Systems TWINDRIVE™ TD3 + HB20RF Systems TWINDRIVE™ TD3
Contents
1. Congratulations on your new elevation bed An actuator is mounted in the bed This is the electronic unit which moves the bed when you press the handset The actuator is a LINAK product LINAK is the worlds leading manufacturer of actuator systems A LINAK actuator is reliable and noiseless it provides a high and constant force and it leaves more space under the bed than any other actuator The actuator has been constructed with full focus on security and at the same time it has lowest power consumption in the market In short A LINAK actuator is a quality product which is built to ensure full functionality several years ahead In this user manual you can find advice and information for correct use of your new elevation bed We recommend that you read the user manual thoroughly through before use so that you will have optimum pleasure with the bed and the LINAK actuator many years ahead Have a good time Mains inlet Battery cable connection HB connection Battery drawer Reset Start up The TD3 can accept commands from up to 2 RF handsets From the factory the TD3 cannot recognize any RF handsets at all Therefore the end user bed manufacturer must match it to the RF handset before they can control the TD3 operation Conditions which must be fulfilled prior to activating the learning mode Both the back and the leg actuators must be in the fully down position if head or foot end are NOT in the fu2. intensity can be controlled when running in a massage program but the massage program will be temporarily halted and both motors are run with currently chosen intensity until up down key is released ae a Controlling massage program Short key press on left key turns on a massage program wave pulse etc or changes to next program if a program is already activated Starting a massage program always turns on both motors at current intensity Short key press on right key turns off both massage motors no matter if it is running in a massage program or separately Keep key pressed to adjust the motor change speed up or down Left key down right key up Tani D AT Store and recall massage settings 2 massage settings can be stored Adjust the massage to the preferred settings Pres the S key followed by either key 1 or 2 To recall a previous stored setting press key 1 or 2 You have chosen a quality and technical product of high value This mounting guideline gives you the information on the use and maintenance of the TWINDRIVE product t3 This is only an additional mounting guideline ua Should you have further questions please contact the g bed manufacturer ual Is only valid for the motor part TWINDRIVE
3. lly down position the matching procedure cannot be continued as now an ordinary reset down function is performed instead Thereafter the reset key must be released and reactivated After battery change press a button for 3 sec Activating the learning mode e Activate the reset key on the TD3 by using a pen or similar to keep the button pressed This learning mode works via battery pack too e Keeping the reset key activated the RF handset s must be activated one at a time by pressing a random key on the RF handset The RF handset ID s are stored in the TD3 memory and at the same time previous RF handset ID s are erased If you like to match 2 RF handsets you should keep pressing the reset key until you have stored both handsets do not release before you matched the second handset otherwise it will recognize only the first one Copyright LINAK 2008 05 MA M9 02 260 Systems TWINDRIVE TD3 HB20RF www linak com LINAK 5 WE IMPROVE YOUR LIFE e After having activated the RF handset keys the reset key must be released e If no RF handset keys are activated during the matching procedure no changes are made in the ID memory of the TD3 e Please be aware that other equipments HB2ORF as e g doorbells which use the 433MHz can disturb the RF signal e Under some circumstances it is not possible to run 2 or more TD3 s at the same time RF signal gets disturbed Please be aware that if yo
4. s been reached HB20 for Massage 1D Enter exit massage command mode Sets the control in massage mode for controlling the massage functions LED flashing or returns to normal mode for controlling the bed adjustment LED off Pressing this key has no influence on the TWINDRIVE unit If no keys are pressed for 10 min the control will automatically go to normal mode LED off CE9 Controlling the backrest massage motor Short key press turns the backrest massage motor on or off Left key on right key off Turning on a motor which has been turned off by turning the intensity to off starts the motor with lowest configured intensity Keep key pressed to adjust the intensity up or down Left key up right key down Keeping the down key pressed will turn the motor off when going below minimal intensity The intensity can be controlled when running in a massage program but the massage program will be temporarily halted and both motors are run with currently chosen intensity until up down key is released lees BD controlling the leg rest massage motor Short key press turns the leg rest massage motor on or off Left key on right key off Turning on a motor which has been turned off by turning the intensity to off starts the motor with lowest configured intensity Keep key pressed to adjust the intensity up or down Left key up right key down Keeping the down key pressed will turn the motor off when going below minimal intensity The
5. u use the TD3 the first time or it has been tSS taken off the current the TD3 RF receiver will need approx 1 min to be able to receive a signal Child lock Enable Disable Child lock To enable the function the position of the switch in the front of the transmitter must be changed N B Child lock do only lock actuators functions Therefore it s disabled while the HB is in Massage command mode Unlock of Child lock Press up and down keys of the 2nd row at the same time for one sec When the blue LED turns on the handset is unlocked The handset is not unlocked If the key s not are released again before the blue led turns off Lock If the up down key is pressed more than 2 sec the handset will lock again Automatic lock The handset is unlocked for 10 sec after last key press Then it automatically locks again Signaling off handset is locked If the handset is locked and the user tries to operate it it will give a short fl ash with the LED to indicate key is pressed but handset is locked Functional description Transmitter HB20 Up down head motor Up down foot motor Simultaneous up down 1 2 3 memory S store How to store e Drive to the desired position e Push S e Immediately afterwards the desired memory position must be pushed 1 2 or 3 e The position is now stored Drive to stored memory position Push 1 2 or 3 keep the button down until the position ha
Download Pdf Manuals
Related Search