ATA User`s manual - PLANET Technology Corporation.
Contents
1. Enable Log System all DoS Sa Enable Log Check to enable log function Upgrade Firmware This page allows you upgrade the ATA firmware to new version Please note do not power off the device during the upload because it may crash the system Upgrade Firmware This page allows you upgrade the ATA firmware to new version Please note do not power off the device during the upload because it may crash the system Select Files as Select File Browse and select file you want to upgrade and press Upload to perform upgrade Please wait till on screen shows related information after upgrade finished 530 Save Reload Settings This page allows you save current settings to a file or reload the settings from the file which was saved previously Besides you could reset the current configuration to factory default Save Reload Settings This page allows you save current settings to a file or reload the settings from the file which was saved previously Besides you could reset the current configuration to factory default Save Settings to File BAVE Load Settings from File fs Reset Settings to Default Save Settings to File Save current settings to a file Reset Settings to Default Press Reset will clean all current configurations and return to default values Password Setup This page is used to set the account to access the web server of ATA Empty user name and password will2. PLANET Networking Communication VolP Analog Telephone Adapter ATA 150 ATA 150S User s manual Version 1 1 Copyright Copyright C 2010 PLANET Technology Corp All rights reserved The products and programs described in this User s Manual are licensed products of PLANET Technology This User s Manual contains proprietary information protected by copyright and this User s Manual and all accompanying hardware software and documentation are copyrighted No part of this User s Manual may be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form by any means by electronic or mechanical Including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use and without the prior express written permission of PLANET Technology Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no
3. 5 C picks up the handset and conversation with A 6 A hang up and C conversation with B 3 Way Conference 1 Aand B are in the process of conversation 2 Awant to invite C to join their conversation 3 Apress Flash button on telephone to hold the conversation with B at first and hear the dial tone then input the number of C Follow by the A key 4 C will ring up and pick up the handset to conversation with A A press Flash button again and they will entry the 3 Way conference mode Call Waiting 1 Aand B are in the process of conversation 2 C call to A and A will hear the prompt sounds 3 Apress Flash button to hold the conversation with B and switch to conversation with C Switch the Default Proxy ATA can register to two different SIP Proxies at the same time lt can receive any one of different SIP accounts incoming call and it can switch to any one SIP accounts for making calls through input 46 the switch code Realm switch code 1500 Realm 1 1501 Realm 2 For example The default is Realm 1 input the 1501 from keypad and hang up the telephone set It will switch to Realm 2 can make the SIP calls via Realm 2 Auto Update firmware by manual Keypad If pick up the handset of ATA it will hear the DoDoDo prompt If want to carry out the upgrade action please input 190 to unlock the device at first Then input 160 to upgrade the new firmware AF x Ap
4. Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN 55022 2006 Class B EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 EN 55024 1998 A1 2001 A2 2003 EN 61000 4 2 2001 EN 61000 4 3 2008 EN 61000 4 4 2004 EN 61000 4 5 2005 EN 61000 4 6 2008 EN 61000 4 8 2001 EN 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Person responsible for making this declaration Name Surname Jonas Yang Position Title Product Manager 1 __Taiwan _ 20 May 2009 u Jana Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw http www planet com tw 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528 gt PLANET Networking amp Communication EC Declaration of Confommi For the following equipment Type of Product VoIP Analog Telephone Adapter 2 FXS Model Number ATA 150S Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C is herewith confirmed to comply with the requirements set out
5. In this example there are three ATA register to IPX 300 and ATA_A had set Call Forward function to ATA B e IPX 300 WAN 192 168 0 1 LAN LAN i ATA A ATA B ATA C Line number Forward Line number Line number 1001 _ 2002 3003 Machine configuration on the ATA Please log in ATA_A via web browser browse to the Phone 1 2 menu and select the Call Forward config menu In the setting page please enable the All Forward function and fill in the number of ATA_B in All Fwd No field then the sample configuration screen is shown below All Forward Of VoIP All Fwd No Busy Forward Off VolP Busy Number Sd No Answer Forward Of VoIP No Answer Fu no No Answer Fwd Time sec 0 Test the scenario 1 2 3 4 ATA_C pick up the telephone Dial the number 1001 ATA _A Because ATA _A had set up All Forward function to the number 2002 ATA _B The number 2002 ATA _B will ring up then it pick up the telephone and communication with the number 3003 ATA _C 44 Case 5 Call Forward Feature_Example 2 In this example there are three ATA and connect with Peer to Peer mode ATA _A had set Call Forward function to ATA _B o Switch Intranet st 97 168 0 197 168 0 2 192 168 0 3 LAN 192 168 0 1 LAN if J Forward ATA_A ATA_B ATA_C Machine configuration on the ATA Please log in ATA_A via web browser browse to the Phone 1 2 menu and select the Call Forward
6. Press this speed dial number and followed by can dial out assigned phone number Phone Number Set phone number for ATA to make speed dial 95 SIP Advanced SIP INFO Duration ms Call Waiting Enable Call Waiting Caller ID O Enable Reject Direct IP Call Enable SIP Port Set local SIP listening port Default 5060 DMTF Relay Select DIMF Relay to be In band RFC 2833 or SIP INFO Default Inband SIP INFO Duration ms If user select DTMF as SIP INFO type here can modify SIP INFO duration ATA will send out DTMF as this duration Default 250 Call Waiting Caller ID Check to enable call waiting caller ID function If this function is enabled caller ID will display when having waiting call Please note that your phone set should also support such function Default Disable 26 NAT Traversal NAT Traversal stun Enable Stun Server Stun Port 348 Stun Check to enable STUN function Default Disable Stun Server Port If user enables STUN function please input STUN Server port Default 3478 E e E kk ade e apto b a e b efe ea os G S pasao a Oo Ss kk daa e fl A o ko Pop e A o Pease aa saa E G726 Packing Order G723 Bit Rate 6 3k na Precedence Set codec priority sequence 1 38 FAX 1 38 Enable T 38 Por Fax Modem Detection Mode ae 1 38 Check to en
7. 0 254 00 e0 4c 61 66 d3 0 8 37 This page shows the packet counters for transmission and reception regarding to Ethernet networks Statistics This page shows the packet counters for transmission and reception regarding to Ethernet networks Ethernet LAN DDNS Sent Packets 527 Received Packets 479 Dynamic DNS is a service which provides you with a valid unchanging internet domain name an URL to go with that possibly ever changing IP address Before setting this page you should click below link to DynDNS or TZO to apply an account for DDNS 35 Dynamic DNS Setting Dynamic DNS is a semice that provides you with a valid unchanging internet domain name an URL to go with that possibly everchanging IP address C Enable DDNS User Name Email n E Note For TZO you can have a 30 days free trial here or manage your TZO account in contro panel For DynDNS you can create your DynDNS account here Enable DDNS Check to enable DDNS function User may register to DDNS server for DDNS function Domain Name Input the applied domain name for ATA Password Key Input password for DDNS server login Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet Current Time ee Time Zone Select OMT 08 00 Pacific Time US
8. Asked Questions List scccssssssssssccccccscsscccssssssssssssssccccccsssssccessssssssssssseses 48 Appendix DATA SDECITICACIONS siria iii iii AAA AAA AA A AAA AAA A cd 49 Chapter 1 Introduction Overview Based on years of VoIP manufacturing experiences PLANET Technology VoIP total solutions are known for advanced implementation of standards based telephony with mass deployment capability Cost effective easy to install and simple to use the PLANET ATA 150 ATA 150S VoIP Phone Adapter ATA in the following term converts standard telephones to IP based networks The service providers and enterprises can offer users traditional and enhanced the telephony communication services via the existing broadband connection to the Internet or corporation network With the ATA home users and companies are able to save the installation cost and extend their past investments in telephones conference and speakerphones The ATA equipped with two telephony interfaces users may register to different SIP proxy servers IP PBX and establish up to 2 concurrent VoIP calls for more flexibility in the voice communications ATA can be the bridge between the traditional analog telephones to IP network with an extremely affordable investment Product Features e Feature rich telephone service over home Internet Intranet connection e Up to 2 concurrent VoIP calls e Cost effective easy to use solution for Analog Telephone Adapter e W
9. Chapter ManaseMent sicicicesvcsccicencsecasevicccccevehanceenedccdcenesacanetocecsseuedeccuessseccoseeeecansiescaceeecseiens 35 AS E is 35 O aanacce nu a eceranamesleensebodauoneune nests maaaevesuboneneuminn oer cesanieameaneisacet 35 BDN eter eet A A A center er eeemied 35 AA a E E E A eal teas reloaded 36 Benia kol rV CO ee a a 37 A aaa altace ae eanaste mane e 38 Upgrade PU MAW Artt tae ee ee 38 Save Reload SENE id 39 Password SU o DORA CP COP ROI OE EE O O Sse oo ee ee ee 39 A E A ees 39 A a ate se camnanncneas coteadenasenetudieeam cen soacie Meme aaa caetnatenesesaara cates cons 40 Appendix A Voice communication SAMPIES cccccccrcrsrrrsssssssssccscccccccccsscccsssssssssssssssscsscccccsssssseeseesssssssecs 41 Peer to DE dea e e EDO 41 Case 2 Peer to Peer mode ATA 150S Port 1 to Port 2 communicati0DS ccccccccnccnnnnnnnnnnnnnnnnnnnnnnos 41 Case ee lP Proy ada 42 Case a Call Forward Feamre Example L esrinorriniinnen n a eden eaa 43 Case gt Call Forward Feature E e ee sae EN 45 Appendix B The method of operation guide ssssssssssececcccoccccsssssesesecceccccocssssssssesscecececeocsssssssssssseeooso 46 sia E A eee ee eects oe 46 De Way COMIC eMC eai Scere decent en Since e eects Siac aes he a 46 RAUL VAIN coi RR 46 SWIC the DELE PEOR AAA A AAA A AA AA essen 46 Auto Update firmware by manual Keypad sssyccasgate toes cies sialeee Sates ninada patie hans had haat Avan dabei A occas 47 Appendix C Frequently
10. Continuous ATA will keep trying to connect to server when PPPoE disconnect If user set type as Connect on Demand please set following idle time ATA will check connection after this time If user set type as Manual ATA will only connect or disconnect by press Connect or Disconnect manually Default Continuous 18 LAN Physical Set IP type if Dynamic IP or Static IP at PPPoE connection Default Dynamic IP Subnet Mask LAN Mask of the ATA at Static IP type Default 0 0 0 0 After confirming the modification you ve done please click on the SUBMIT button to apply settings effective and the ATA will be reload page automatic by itsely that you must to afresh enter the final modification IP address for logon web management Connection Type Description PPTP IP Type FPTP v Mode Dynamic IP Static IP IF Address Subnet Mask Gateway Server IP Address ee E jaa a Sue 1400 1460 bytes C Request MPPE Encryption Attain DNS Automatically Set DNS Manually Clone MAC Address C Enable uPNP Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Apply Changes 19 PPTP Set LAN interface as PPTP mode IP Address LAN IP Address of the ATA at Static IP type Default 0 0 0 0 Gateway Gateway of the ATA Default 0 0 0 0 User Name Set user name of PPTP
11. Path Check new firmware Power On Scheduling Schuduling Day O 1 30days Schuduling Time AM 0000 05 59 w Auto Update Automatic Notify Only Fle Pro Next Update Time Ott Firmware Version Aa Mode There are TFTP FTP and HTTP three ways to provide the auto upgrade function HTTP Server Address Input the HTTP Server address and it could input the IP or Domain Name form FTP Server Address Input the FTP Server address and it could input the IP or Domain Name form FTP Password The login password Check new firmware The ATA will according to the below ways to check the new firmware Power On The machine will check the new firmware when power on and following the scheduling date and time Scheduling The machine will follow the scheduling date and time to check the new firmware Scheduling Time The ATA will check the new firmware between the time range by random File Prefix It will check the information of model name 34 Status Chapter 5 Management In this page can show the current status and some basic settings of the ATA Status This page shows the current status and some basic settings of the device Uptime Firmware Version Build Time Attain IP Protocol IP Address Subnet Mask Default Gateway MAC Address Version Statistics Oday Oh m 52s v1 0 Fri 31 Oct 2008 15 19 25 0600 Fixed IP 192 168 0 1 255 255 255 0 192 168
12. amp Canada Tijuana C Enable NTP client update NTP server E 112 541 41 North America OL tana iP Sting Current Time Input current time manually 36 Enable NTP client Check to enable NTP update Once this function is enabled ATA update will automatically update current time from NTP server Denial of Service A denial of service DoS attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service Denial of Service A dental of service DoS attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service Enable DoS Prevention Whole System Flood SYN Packets Second Whole System Flood FIN Packets Second Whole System Flood UDP Packets Second Whole System Flood ICMP Packets Second Per Source IP Flood SYN Packets Second Per Source IP Flood FIN Packets Second Per Source IP Flood UDP Packets Second Per Source IP Flood ICMP Packets Second TCP UDP Port Scan Low Sensitivity ICMP Smurf IP Land IP Spoof IP Tear Drop Ping Of Death TCP Scan TCP Syn With Data UDP Bomb UDP Echo Chargen Sie ACL Enable Source IP Blocking Block time sec Enable DoS Prevention Check to enable DoS function ee Log This page can be used to set remote log server and show the system log System Log This page can be used to set remote log server and show the system log
13. config menu In the setting page please enable the All Forward function and fill in the IP address of ATA_B in All Fwd No field then the sample configuration screen is shown below All Forward Of VoIP All Fwd No Busy Forward Of O VoIP Busy Number No Answer Forward OF O VoIP No Answer Fu No No Answer Fwd Time fse 0 Test the scenario 1 ATA_C pick up the telephone 2 Dial the IP Address 192 168 0 1 ATA_A 3 Because ATA_A had set up Immediate Forward to function to the IP Address 192 168 0 2 ATA_B 4 The IP Address 192 168 0 2 ATA_B will ring up then it pick up the telephone and communication with the ATA_C 45 Appendix B The method of operation guide In this section we ll introduce the features method of operation and lead you step by step to establish these features Call Transfer A Blind Transfer 1 B call to A and they are in the process of conversation 2 Acarry the transfer function out Press 1 button to hold the conversation with B 3 Awill hear the dial tone then input the number of C Follow by the HP key 4 C will ring up then A hang up the handset 5 C picks up the handset and conversation with B B Attendant Transfer 1 B call to A and they are in the process of conversation 2 Acarry the transfer function out Press 1 button to hold the conversation with B 3 Awill hear the dial tone then input the number of C Follow by the FP key 4 C will ring up
14. disable the protection Password Setup This page is used to set the account to access the web serer of ATA Empty user name and password will disable the protection Now Password oo Confimed Password User Name Enter user name Confirmed Password Confirm password again Reboot Press Reboot to reboot system Please wait for a few minutes and reload web page again 39 System Reboot Press Reboot to reboot system Please wait for a few time and reload web page again Logout This page is used to logout Logout This page is used to logout Do you want to logout _ 40 Appendix A Voice communication samples There are several ways to make calls to desired destination in ATA In this section we ll lead you step by step to establish your first voice communication via keypad and web browsers operations Peer to peer P2P mode Assuming there are two ATA in the network the IP address are 192 168 0 1 and 192 168 0 2 ATA A ATA B LAN IP address XU AM i LAN IP address 192 168 0 1 Y 192 168 0 2 ede elle Elle Tell STEP Pick up telephone handset of ATA A and dial 192 168 0 2 Then the phone of ATA B should ring You can do the same thing to the ATA B If the IP address of the remote calling party is known you may directly make calls by preset number via its IP O Hint address and end with If the Telephone Adapter is installed behind a NAT firewall IP sharing d
15. gt PLANET ATA VolP Adapter Rebworkirg A Ccomuricstim Site contents Ra Network m SIP Settings This page illustrate the system related information Management B Reboot Logout Company PLANET Technology Corp 11F No 96 Min Chuan Road Hsin Tien System Information ER es aes Taipei Taiwan R O C Tel 886 2 22199518 888 2 22199528 E Mail BSP E TEE Web Site www p lanet com tw VolP Phone Adatper main page LAN IP address configuration via web configuration interface This page is used to configure the parameters for Internet network which connects to the LAN port of your ATA Here you may change the access method to static IP DHCP PPPoE or PPTP by click the item value of LAN Access type LAN Interface Setup This page ts used to configure the parameters for Internet network which connects to the LAN port of your ATA Here you may change the access method to static IP DHCP PPPoE or PPTP by click the item value of LAN Access type P Type IP Address Subnet Mask Default Gateway MTU Size 1400 1500 bytes DNS 1 y Clone MAC Address Enable uPNP Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection _15 Connection Type Description Static IP Static IP Set LAN interface as Static IP mode Subnet Mask LAN mask of the ATA Default 255 255 255 0 MTU Size set MTU maximum transmission unit s
16. responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions CE mark Warning The is a class B device In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Stand by mode operation For energy saving please remove the DC plug or push the hardware Power Switch to OFF position to disconnect the device from the power circuit Without remove the DC plug or switch off the device the device will still consuming power from the power circuit In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to switch off or remove the DC plug for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crosse
17. will be played for 100ms Default 0 ee Other Function Key Must be 0 9 Call Transfer default 1 Call Transfer Set call transfer function key Default 1 Dial Option Auto Dial Time 3 9 sec 0 is disable Auto Dial Time Set Auto dial time When user finish input number after this time ATA will dial out immediately If the call is ended by the call will be send immediately and you do not need to wait for the Auto Dial time Default 5 Off Hook Alarm Off Hook Alarm Time 10 60 sec 0 is disable Off Hook Alarm Time Set off hook alarm time If phone set has been off hook after this time from phone sett will hear alarm Default 30 QoS You can define the DSCP code here for SIP and RTP Higher DSCP higher priority When DSCP is defined a DSCP will be added in SIP and RTP packets and the priority of voice should be higher than data SIP DSCP EF QDSCP Onze wv RTP DSCP EF DSCP Cn2e w ze Auto Config Auto Config ATA supports HTTP TFTP and FTP auto configuration function in total Mode O HTTP O TFIP FIP Disable HTTP Sener Address OOOO HTTP Server Port TIP Sener Ad ress FTP Sener Adress OOOO FTP Usemame OO FP Passwd Fie Path Expire Time O days Auto Firmware Update The ATA can update new firmware file automatically by the Auto Firmware Update function ATP rep OOOO FTP Sener Address FTP Usemame OOO FTP Password FTP
18. 0 Number 200 ATA B LAN IP address a LAN IP address 192 168 0 1 192 168 0 2 IPX 2000 or IPX1900 LAN IP address 192 168 0 50 STEP 1 Log in IPX 2000 or IPX 1900 and create two testing accounts password 100 123 for ATA A and 200 123 for ATA B for the voice calls STEP 2 Please log in ATA A via web browser find to the SIP item In the setting page please insert the account password information obtained from your service provider in this sample we re using PLANET IPX 2000 or IPX 1900 as the IP PBX server for SIP account call authentications and then the sample configuration screen is shown below SAD x Line Number Register Name Register Password Proxy Server Proxy Port Domain Server SIP Expire Time Outbound Proxy Outbound Proxy Server Outbound Proxy Port Register Status STEP 3 Repeat the same configuration steps on ATA B and check the machine registration status make sure the registrations are completed STEP 4 To verify the VoIP communication please pick up the telephone Dial the destination number to make call between SIP clients For example ATA A with number 100 with keypad number 200 to ATA B or reversely makes calls from SIP client ATA B to the number 100 ATA A Case 4 Call Forward Feature_Example 1 LO LO Enable 192 168 050 li Enable l Registered In the following samples we ll introduce the Call Forward Feature applications
19. 1 STUN RFC 3489 UPnP MDS5 for SIP authentication RFC 2069 RFC 2617 G 711 G 723 G 729 Voice Standard Voice activity detection VAD Comfort noise generation CNG G 168 Line echo canceller LEC Jitter Buffer DTMF Detection and Generation In Band and Out of Band RFC 2833 SIP INFO QoS IP TOS IP Precedence DiffServ FAX support T 38 FAX Relay G 711 Fax pass through Telephony Features Call Waiting Call Hold Resume Call Transfer Blind Transfer Attended Transfer Call Forward On Busy Forward No Condition forward No Answer Forward Call Screen Incoming Call Screen Reject or Forward Incoming Call Outgoing Call Screen Blocking Outgoing Call 3 Way Conference Configuration amp Web based Graphical User Interface Management Remote management over the IP Network Web based firmware upgrade Backup and Restore Configuration file SNMP vi v2 TR 069 Network and Configuration _ 49 PLANET Networking amp Communication Q EC Declaration of Confomi For the following equipment Type of Product VoIP Analog Telephone Adapter 1 FXS Model Number ATA 150 Produced by Manufacturer s Name Planet Technology Corp Manufacturer s Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
20. able T 38 function Default Disable DSP Vad DTMF FSK Date amp Time Sync C Enable Reverse Polarity before Caller ID C Enable Short Ring before Caller ID C Enable Dual Tone before Caller ID C Enable Caller ID Prior First Ring Enable Caller ID DTMF Start Digit DTMF_ Caller ID DTMF End Digit DTME_C y Flash Time Setting ms lt Flash Time lt Space 10 Min 30 Max 2000 Speaker Voice Gain dB 32 31 Mute 32 Mic Voice Gain dB 32 31 Mute 32 Vad Check to enable VAD Voice Activity Function function Default Disable FSK Date amp Time Sync Check to send FSK Date and Time to caller ID display device Default Disable Short Ring before Caller ID Check to send short ring before caller ID Default Disable _ 28 Caller 1D Prior First Ring Check to send caller ID before first ring Default Enable Caller ID DTMF End Digit Set caller ID DTMF end digit Default DTMF_C Speaker Voice Gain dB Set Speaker voice volume 32 31 Mute 32 Det DND Don t Disturb Semice Domain Call Forward Dial Plan Advanced Others DND Mode O Always O Enable Disable From 0 2 nte To 09 22 _ hhamm DND Mode You can select 3 mode of DND The call will be always rejected if Always is selected The call will be rejected by below Time setting From and To if Enable is selected The call will be ac
21. answer time Once phone is not picked up after this time incoming call be will forwarded to assigned number Default 0 siy Dial Plan Replace prefix code Dial Plan Select to enable On or disable Off prefix replace function Default Off User can set how many digits or which number for ATA to dial out immediately Available parameters are 0 9 2 X Symbol means or x could be numbers 0 9 For example user can set Dial Plan as 911 xXxXxxxxxx xx which means if user dial 911 87654321 or 11 these number will be dial out immediately without waiting for dial time or pressing sign Default Null Prefix Unset Plan User can set special access code to disable Auto Prefix function in single call Available parameters are 0 9 PP 2 X Symbol means or x could be numbers 0 9 For example if user set Prefix Unset Plan as 1 xxxxxxxxxx When dialed number as 1 87654321 or 10 digits of number for this call will not be added with Auto Prefix number Default Null Dl Abbreviated Dial Phonebook Abbreviated Name Abbreviated Dial Phonebook access code Input this number and followed by can dial out assigned phone number Speed Dial Speed Dial Position Phone Number Select 0 TTT Reve Al Position Speed Dial access code
22. cepted if Disable is selected Default Disable To Set the end time for DND with Enable mode Default 00 00 Alarm Enable L Time o o hh mm 29 Enable If set up as Enable the telephone will ringed up at the specific time Default Disable Hot Line Use Hot Line _ Enable Hot Line Number Oo Use Hot Line Hot Line Number Default Disable one User can adjust the items of the Call Control when in VolP communication And basically system will use the following default setting values if user does not want to change them Select Country Select Country Country TAIWAN v Apply Country User can select country to specify tone parameters Dial Tone Ring Tone Busy Tone and Waiting Tone If user wants to set tone manually please select CUSTOMER After selecting CUSTOMER user can assign Custom 1 to 8 for each tone Default TAIWAN 30 Select Country Select Custom Tone Custom Tone Custoral Custom Tone Select Custom tone number to set Tone Parameters Default Custom1 Tone Parameters Tone Parameters Gana DOO O ieas caon DO es Freq1 Set first set of tone frequency in HZ Default 0 Gain1 Set volume level of Freq1 in dB 7 10 Please set this parameter under zero and suggested to set between 7 to 10 Default 0 CanOn Set cadence time for tone to play in ms For example if set CanOn as 100 the tone
23. connection Default Null Please be noticed that the Utility Tool is only designed L Note for the LAN environment setting If the Connect Type is PPPoE the Utility Tool can NOT find the device 20 Chapter 4 VoIP Settings Phone 1 Phone 2 ATA 150S Here is to set VoIP Phone 1 and Phone 2 ATA 1505 related configurations Default Proxy Select Default Proxy Select Default Proxy Each Phone port has support register two different Proxy Servers When select one of Proxy as default ATA will use this account for making outgoing call And ATA could receive incoming calls through both Proxys Default Realm Realm 1 Realm 2 VoIP General Settings Semice Domain Call Forward Dial Plan Advanced Default Proxy Select Default Proxy Proxy0 Display ame Line Number Register name Register Password Proxy C Enable pi Oo Proxy Por A 7 SP Expire Time Outbound Proxy L Enable Outbound Pray Sener SSS Outbound Proxy Port Register Status Not Registered Jia Display Name Number Login ID Password Proxy Proxy Addr Proxy Port SIP Domain Reg Expire sec Outbound Proxy Outbound Proxy Addr Outbound Proxy Port Register Status Set ATA Phone display name for caller ID information Default Null Set registering Phone number Default Null If Proxy server needs registration authentication please input Login ID here Default Null I
24. d out wheeled bin symbol Do not dispose of oo Oe WEEE as unsorted municipal waste and have to collect such WEEE separately Trademarks The PLANET logo is a trademark of PLANET Technology This documentation may refer to numerous hardware and software products by their trade names In most if not all cases their respective companies claim these designations as trademarks or registered trademarks Revision User s Manual for PLANET VoIP Analog Telephone Adapter Model ATA 150 ATA 150S Rev 1 1 2010 October Part No EM ATA150 Series TABLE OF CONTENTS Chapter E Intro d UCA Aces ceiiaiadian 6 OV CE VIC W OPEP AA ono A 6 Package Content A a A aa 7 Physical Detalla ciar idad dani 7 PC O E ES CURNNO 8 Chapter 2 Preparations amp Installation c ccsssssssssccccccsssssssssscccccssccsssssssscccsssseeesssssecs 10 Physical Installation Requirements einai nese ad 10 Ty AC COMI ATI A A Aer I tO 11 Chapter gt TOP UP SCS ia 14 Configuring and monitoring your ATA from Web browser ccccccccccssssssssssssssssssssssscscccccccssssssseeeeeees 14 Overview onthe website face OL ATA isa 14 Manipulation of ATA via web DI 14 LAN IP address configuration via web configuration interface oooooncccconooaooononoonoonnnnnnnnnnnnnnononnnnnnnnnos 15 Chapter 4 VolP Sete cui a o nadia 21 Phone Pine 2 ALTAS id 21 A ric anai site a a ats fics aan ncian E ceases 30 OO Eeee A ads 32 AWO CONI Mn UI e e o E e A ee ee 33
25. eb based utility and machine configuration e Remote administrator authentication e Voice prompt for machine configurations VoIP Features e SIP 2 0 RFC3261 compliant e Voice codec G 711 A law u law G 729 AB G 723 6 3 Kbps 5 3Kbps e FolP T 38 FAX Relay G 711 Fax pass through e QoS IP TOS IP Precedence DiffServ e Call Waiting Hold Resume Transfer Forward e 3 Way Conference Caller ID Generation e VAD CNG Dynamic Jitter Buffer e SNMP v1 v2 TR 069 and Auto Provision Package Content The contents of your product should contain the following items VolP Telephone Adapter Power adapter Quick Installation Guide User s Manual CD RJ 11 cable x 1 Physical Details The following figure illustrates the each panel of SIP ATA ATA 150 SIP Analog Telephone Adapter 1 x RJ 45 1 x RJ 11 ATA 1508S 2 Port FXS SIP Analog Telephone Adapter 1 x RJ 45 2 x RJ 11 PLANET VoIP Analog Telephone Adapter ODO ARA Front Panel of ATA 150 z Dc Left Right Panel of ATA 150 PLANE Y Front Panel of ATA 150S Left Right Panel of ATA 150S Physical Interface 8 Button Pressing 1 second to reboot machine 1 RESET Pressing 5 seconds to reset to the factory default setting RJ 45 connector for Internet access connected directly to Switch Hub through straight CAT 5 cable 3 LAN 8 LED Display of ATA 150 PWR Power is supplied to the device OFF the
26. ess bar of your web browser to logon ATA web configuration page To start ATA web configuration you must have one of these web browsers installed on computer for management o Microsoft Internet Explorer 6 00 or higher with Java support Please locate your PC in the same network segment 5 Note 192 168 0 x of ATA If you re not familiar with TCP IP please refer to related chapter on user s manual CD or consult your network administrator for proper network configurations Keypad commands The ATA series phone adapters support telephone keypad configurations please connect analog telephone set and refer to the following table for machine network configurations IVR Menu Choice Machine operation Parameter s Notes oo ATA will change to DHCP Set DHCP client Client Use the star key DHCP will be disabled and Setup Static IP Address when entering a decimal system will change to the 11 Use the star key 113XXX XXX XXX Set Network Mask when entering a decimal Must set Static IP first xxxH point Use the star key 114xxx xxx xxx Set Gateway IP Address when entering a decimal Must set Static IP first XXx point Use the star key 115XXX XXX XXX Set Primary DNS Server when entering a decimal Must set Static IP first XXX point Must unlock the protect function before carry out 190 Unlock None the firmware update 160 Must save network settings after set up Save N
27. etwork Settings network settings via keypad The system will be reset to Factory Reset factory default value and reboot automatically prompt IVR will announce the current IP address of Check IP Address the ATA IVR will announce if DHCP in enabled or Check network connection Type disabled IVR will announce current enabled VoIP Check the Phone Number number IVR will announce the current network mask Check Network Mask of the ATA IVR will announce the current gateway IP address of the ATA Check Gateway IP Address IVR will announce the current setting in the DNS field Check DNS Server Setting IVR will announce the version of the Check Firmware Version firmware running on the ATA ls Following keypad commands can be used to set up the main function 01 G 711 u Law 02 G 711 a Law 03 G 729 You can set the codec you 04 G 723 6 3K 05 want to the first priority 130 first Set First Priority Codec G 723 5 3K 06 G 726 For example 13001 priority codec 16K 07 G 726 24K 08 Set G 711 u Law to the first G 726 32K 09 G 726 priority codec 40K 10 GSM FR For example 13410 Mic Voice 10 Set Mic Voice Gain 00 31 32 Mute Disable call waiting None Disable Call waiting Update firmware Must unlock the protect 160 Update firmware function 190 before carry out the firmware update 13 Chapter 3 TCP IP Settings Configuring and monitoring y
28. evice please make sure the NAT device support SIP applications before making calls Case 2 Peer to Peer mode ATA 150S Port 1 to Port 2 communications Supposing one ATA 150S connects to two telephones just pick up phone 1 and dial 192 168 0 1 5061 phone 2 will ring Analog telephone sets are connected to the phone RJ 11 ports of ATA 150S respectively 192 168 0 1 da w da 1001 1002 HEI bee AeA 4 Test the scenario 1 Pick up the telephone set on ATA 150S port 1 and you should be able to hear the dial tone 2 Press the keypad 192 168 0 1 5061 shall be able to connect to the ATA 150S port 2 3 Then the telephone set in ATA 150S port 2 should ring Please repeat the same dialing steps on port 2 to establish the first voice communication from ATA 150S If the IP address of the remote calling party is known you may directly make calls via its IP address and end with a Hint If the ATAs are installed behind a NAT firewall IP sharing device for Peer to Peer VoIP application please make sure the NAT device support SIP applications and suitable settings should be applied to the NAT device to enable the SIP communications before making calls ATA 150S in PLANET ATA series products to connect to remote ATA press the keypad in the following sequence to connect to the remote ATA 150S port 2 Remote ATA IP address 5061 for example 192 168 0 2 5061 Case 3 SIP Proxy mode ATA A Number 10
29. f Proxy server needs registration authentication please input password here Default Null Check to enable Proxy mode Default Disable If user enable Proxy mode please input Proxy address Default Null If user enable Proxy mode please input Proxy port Default 5060 Set SIP domain name for SIP signaling Default Null Set expire time of registration ATA will keep re registering to proxy server before expire timed out Default 60 Check to enable Outbound Proxy mode Default Disable If user enables Outbound Proxy please input Outbound Proxy address Default Null If user enables Outbound Proxy please input Outbound Proxy port Default 5060 Here will display SIP account register status DD Forward Mode Sonics Doma Call Forward Toara DSP Call Forward All Forward No Answer Time sec Immediate Forward to This is unconditional forward setting All incoming call will be forwarded to specified number Check to enable immediate forward function Default Off Busy Forward to Check to enable Busy Forward function When phone is busy incoming call will be forwarded to assigned number Default Off No Answer Forward to Check to enable no answer forward function When phone is not answered for a period of time incoming call will be forwarded to assigned number Default Off No Answer Time sec Set no
30. in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on 2004 108 EC For the evaluation regarding the EMC the following standards were applied EN 55022 2006 Class B EN 61000 3 2 2006 EN 61000 3 3 1995 A1 2001 A2 2005 EN 55024 1998 A1 2001 A2 2003 EN 61000 4 2 2001 EN 61000 4 3 2008 EN 61000 4 4 2004 EN 61000 4 5 2005 EN 61000 4 6 2008 EN 61000 4 8 2001 EN 61000 4 11 2004 Responsible for marking this declaration if the Manufacturer O Authorized representative established within the EU Authorized representative established within the EU if applicable Company Name Planet Technology Corp Company Address 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Person responsible for making this declaration Name Surname Jonas Yang Position Title Product Manager al Taiwan 18 Aug 2009 Jer Place Date Legal Signature PLANET TECHNOLOGY CORPORATION e mail sales planet com tw _ http www planet com tw 11F No 96 Min Chuan Road Hsin Tien Taipei Taiwan R O C Tel 886 2 2219 9518 Fax 886 2 2219 9528
31. ize Default 1412 Clone MAC Address To clone the MAC by manual input Default 000000000000 Null Enable IPsec pass through on Check to enable IPsec function VPN connection Default Enable Enable L2TP pass through on Check to enable L2TP pass through function VPN connection Default Enable 16 Connection Type Description DHCP Client IP Type DHCP Client v Host Name MTU Size 1400 1492 bytes O Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Address Enable uPNP Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection DHCP Client Set LAN interface as DHCP mode 17 Connection Type Description PPPoE UserName passwords O SeviceName Connection Type Connect Disconnect Idle Time 1 1000 minutes MTU Size 1360 1492 bytes WAN Physical Dynamic IP Static IP IP Address Subnet Mask Attain DNS Automatically Set DNS Manually Clone MAC Address Enable uPNP Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection PPPoE Set LAN interface as PPPoE mode Password Set password of PPPoE connection Default Null Connection Type Set PPPoE connection type to be Continuous Connect on Demand Manual If user set type as
32. our ATA from web browser The ATA integrates a web based graphical user interface that can cover most configurations and machine status monitoring Via standard web browser you can configure and check machine status from anywhere around the world Overview on the web interface of ATA With web graphical user interface you may have More comprehensive setting feels than traditional command line interface Provides user input data fields check boxes and for changing machine configuration settings Displays machine running configuration To start ATA web configuration you must have one of these web browsers installed on computer for management Microsoft Internet Explorer 6 00 or higher with Java support Manipulation of ATA via web browser Log on ATA via web browser After TCP IP configurations on your PC you may now open your web browser and input http 192 168 0 1 to logon Phone Adapter web configuration page Edit View Favorites Tools Help E E iOD anl p E a EI Enter the IP address of the ATA which ap Ocoh El x lz fa Search by default is 192 168 0 1 rU UOU Arnes E http f 192 168 0 1 Phone Adapter will prompt for logon username password admin 123 ATA YolP Adapter User name E wt C Remember my password ATA login prompt screen 14 When users login the web page users can see the Phone Adapter system information like firmware version company etc in this main page
33. pendix C Frequently Asked Questions List If your SIP ATA is not functioning properly you can refer to this chapter first for sample troubleshooting before contacting your dealer This can save your time and effort but if the symptoms persist please consult your dealer Q I forget my ATA login username and or password A 1 Restore ATA to its factory default settings by pressing the Reset button which is at the side panel of the device for 5 seconds or more Q Non of the LEDs are on when I turn on the SIP ATA A 1 Check if power cord is connected properly 2 Check if there is proper AC power coming from the power outlet Q Why can t I dial my friend s SIP number A 1 Check SIP Server Domain Name IP address Make sure you have the right Name or IP address 2 Check the web browser and access the configuration menu Make sure that the SIP Server Domain Name IP Address is correct 3 Check the register status under SIP Account Settings in the configuration menu from web browser If your status is Not Registered it means you do not have a SIP account Contact your SIP service provider to get an account Q How to know the machine IP address A 1 To pick up the telephone set and key in 120 2 Machine will prompt the current IP address 48 Appendix D ATA Specifications Product SIP Analog Telephone Adapter Model 3 ATA 150 ATA 1508 Hardware Standard SIP 2 0 RFC326
34. phone is idle Phone ON the phone is in use off hook Blinking the phone is ringing LED Display of ATA 150S PWR Power is supplied to the device OFF the phone is idle RING1 ON the phone is in use off hook Blinking the phone is ringing 1 Machine default IP is http 192 168 0 1 Press RESET button on rear panel over 5 seconds will reset the VoIP b Note Phone Adapter to factory default value Except speed dial and call forward settings 2 Using the power supply that is not the one included in package will cause damage and void the warranty for this product 3 Be noted to use the switching type power supply for regular operating Chapter 2 Preparations amp Installation Physical Installation Requirement This chapter illustrates basic installation of ATA analog Phone Adapter ATA in the following term e Network cables Use standard 10 100Base TX network UTP cables with RJ 45 connectors e TCP IP protocol must be installed on all PCs For Internet Access an Internet Access account with an ISP and either of a DSL or Cable modem Administration Interface PLANET ATA provides GUI Web based Graphical User Interface and utility for machine management and administration Utility quickly search access Using for soft utility to search SIP ATA from current network The utility not only easy to use and provides user more convenience for configuration access at the some time If yo
35. u forget this IP address can also found that via the utility Copy this utility tool in your laptop or desktop computer first And this utility tool can only be executed in Windows series of operating systems Click the icon for windows desktop to start searching ATA in the network eb PLANET Smart Discovery Lite File Option Help Tom _ ae HeC Adress Device Name Version Device __ NewPasowor P Ades q 00 30 4 01 01 01 aTa 1508 vio 19216801 2 192 168 0 1 255 255 255 0 192 168 0 254 ATA 1505 select Adapter 192 168 0 201 00 0 18 48 09 71 ka T Control Packet Force Broadcast 3 Update Device Update Multi Update All Connect to Device Device ATA 1508 00 30 4F 01 01 01 Get Device Information done Select Refresh and you will get the results as above choose the device you want to configuration click this IP address of ATA and press the Connect to Device button to browse the web page 10 Web configuration access You will connect to SIP ATA via your web browser automatically ATA will prompt for logon username password please enter admin 123 to continue machine administration ATA VolP Adapter User name E WH Remember my password ATA will prompt for logon username password please enter admin 123 to continue machine administration The default IP address of ATA is 192 168 0 1 You also could open your web browser and insert http 192 168 0 1 in the addr
Download Pdf Manuals
Related Search