PM-IRRAS Accessory - Agilent Technologies
Contents
1. PM IRRAS Accessory Hardware Manual 2 PM IRRAS Accessory Hardware Manual Notices Agilent Technologies Inc 2010 2013 No part of this manual may be reproduced in any form or by any means including electronic storage and retrieval or translation into a foreign language without prior agreement and written consent from Agilent Technologies Inc as governed by United States and international copyright laws Manual Part Number 8510258800 Edition Fifth edition May 2013 Printed in Malaysia Agilent Technologies Inc Warranty The material contained in this document is provided as is and is subject to being changed without notice in future editions Further to the maximum extent permitted by applicable law Agilent disclaims all warranties either express or implied with regard to this manual and any information contained herein including but not limited to the implied warranties of merchantability and fitness for a particular purpose Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing use or performance of this document or of any information contained herein Should Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms the warranty terms in the separate agreement shall control Technology Licenses The hardware and or software d2. 36 This chapter includes maintenance procedures for the Polarization Modulation Infrared Reflection Absorption Spectroscopy PM IRRAS Accessory that may be carried out by an operator Any maintenance procedures not specifically mentioned in this chapter or in the Help should be carried out only by an Agilent trained Agilent qualified or Agilent authorized customer service representative WARNING Electrical Shock Hazard This accessory contains electrical circuits devices and components operating at dangerous voltages Contact with these circuits devices and components can cause death serious injury or painful electrical shock Always follow the procedures described by Agilent Cleaning Any spills on the PM IRRAS should be immediately wiped up The exterior surfaces of the PM IRRAS should be kept clean All cleaning should be done with a soft cloth If necessary this cloth can be dampened with water or a mild detergent Do not use organic solvents or abrasive cleaning agents Maintenance 36 PM IRRAS Accessory Hardware Manual Fuses The only user accessible fuse in the PM IRRAS is the mains inlet fuse for the PEM controller Refer to the PEM 100 User Manual for details Always turn off the power and remove the power cord before replacing fuses Fuses should be replaced only with the same type and rated fuses as specified on the rear of the controller WARNING Shock and Fire Hazards This accessory contains electr
3. Ensure that there is an integral ground connection between the metal surfaces of the PM IRRAS accessory and the 3 pin earth grounded receptacle NOTE The above model is Equipment Class I Application of the wrong supply voltage can create a fire hazard and a potentially serious shock hazard and could seriously damage the PM IRRAS accessory Replace blown fuses with fuses of the size and rating as stipulated in the text adjacent to the fuse holder or in the manuals where listed Do NOT use power cords with faulty or frayed insulation Laser safety The Agilent PM IRRAS accessory is used with Agilent FTIR spectrometers which incorporate a helium neon He Ne laser operating in the visible region at 632 8 nanometers The spectrometer is a Class 2 laser product powerful enough to warrant caution in its use Agilent FTIR spectrometers comply with FDA and CE standards for light emitting products Safety Practices and Hazards PM IRRAS Accessory Hardware Manual 7 An attenuated portion of the laser beam passes into and through the spectrometer sample compartment and can be directed from there into the accessory Although not powerful enough to harm your skin should your hand intercept it the laser light could cause retinal eye damage during prolonged direct viewing This is not possible given the normal optical layout of the spectrometer However if a highly reflective surface such as a mirror is allowed to intercept the beam the b
4. To perform PM IRRAS measurements in rapid scan mode skip forward to Page 32 Basic Operation PM IRRAS Accessory Hardware Manual 27 Data Collection in Step Scan Mode 1 Go to Collect gt Step Scan gt Step Scan Select the following parameters a Electronics Speed 800 Hz UDR 2 Filter NONE b Optics Source Mid IR Beam Path Right Detector Ext 1 Aperture 2 cm 1 Attenuator 50 2 Click Setup 3 Click Align 4 Click Find Centerburst 5 Go to Collect gt Step Scan gt PM IRRAS DSP 3 and set the parameters as a PM IRRAS DSP 3 Linear Dichroism Signal at 74 KHz Sample Modulation Frequency 50 Hz Modulation Amplitude 1 Delay After Step ms 55 PEM Frequency in Hz Set to equal the 2F frequency displayed on PEM controller may need to be calculated Save Raw Data Starting Step 75 Save Raw Data Total Step Number 1 Basic Operation 28 PM IRRAS Accessory Hardware Manual b Electronics Speed Unavailable UDR 4 Filter Unavailable Resolution 8 cm 1 Sensitivity 1 Scans to Co add 1 c Optics Source Mid IR Beam Path Right Detector Ext 1 Aperture 2 cm 1 Attenuator 50 d Advanced Interferogram Symmetry Asymmetric 6 The switches on the DSP3 Filter B
5. Introduction PM IRRAS Accessory Hardware Manual 13 2 Introduction Specifications 13 Environmental 13 Power 14 Purge gas 14 Liquid nitrogen 15 Weights and dimensions 15 Space 15 Installation requirements 16 Training 16 Documentation 16 Specifications Environmental The Agilent Polarization Modulation Infrared Reflection Absorption Spectroscopy PM IRRAS accessory is designed for indoor use It is suitable for the following categories Installation category II Pollution degree 2 Equipment Class I These conditions are required for proper operation of your PM IRRAS accessory Temperature 20 C to 26 C 68 F to 80 F Temperature gradient 1 C hr 1 8 F hr maximum Relative humidity 20 to 50 non condensing Introduction 14 PM IRRAS Accessory Hardware Manual Altitude 3000 m 10 000 ft maximum Free from corrosive and flammable fumes Free from strong electromagnetic fields NOTE Performance degradation may result from the exposure of the spectrometer to strong radio frequency energy If degradation is experienced reorient or relocate the spectrometer or the radio frequency source Free from vibrations Power PEM controller 60 VA 100 to 240 VAC 60 W 50 or 60 Hz An auto ranging power supply is used No reconfiguration is required for voltage changes Dedicated 10 A circuit with grounded receptacle
6. Purge gas A source of clean dry air dried to dew point of 70 C or liquid nitrogen boil off to be used as a purge gas Where compressed nitrogen is used it must be dry oil free and uncontaminated with purity of 99 996 or better A flow rate of 13 L min 30 ft3 hr maximum is required to assure a non condensing environment The gas supply must be equipped with fittings to accept 6 mm outer diameter OD tubing Tubing should be clean and free of any dust and debris Do not use tubing treated with talcum powder Introduction PM IRRAS Accessory Hardware Manual 15 Liquid nitrogen WARNING Extreme Cold Hazard Liquid nitrogen is very cold and can cause damage to the human body Use appropriate protective equipment when handling liquid nitrogen The detector in the PM IRRAS accessory will require a supply of liquid nitrogen to cool it It takes about 500 milliliters 16 ounces of liquid nitrogen for the initial fill to bring the Dewar to an equilibrium temperature It will take about 20 minutes to reach equilibrium Then add an additional 200 milliliters 7 ounces of liquid nitrogen to top off the Dewar Weights and dimensions Width 67 5 cm 27 in Depth 61 cm 24 in Height 27 5 cm 11 in Weight 45 kg 100 lb Space A flat and level surface is required It must be rigid enough to support the weight of the spectrometer and the PM IRRAS accessory and any additional accessories
7. analysis methodology operating procedures and various accessories is provided in the Help and electronic manuals saved onto your computer hard drive during software installation for your Agilent FTIR spectrometer Hardware PM IRRAS Accessory Hardware Manual 17 3 Hardware Overview 17 Beam path 18 Filters 19 Orientation of sample and detector 20 Overview The Agilent Polarization Modulation Infrared Reflection Absorption Spectroscopy PM IRRAS accessory is designed to be used as an accessory for Agilent FTIR spectrometers The PM IRRAS accessory is used for grazing angle reflectance spectroscopy The PM IRRAS accessory includes External Experiment Module EEM including Plexiglas cover Base plate with optics mounts Base plate with one liquid nitrogen cooled detector Photoelastic Modulator PEM PEM controller complete with user manual This hardware manual NOTE The PEM and the PEM controller are manufactured by Hinds Instruments Inc Details concerning operation and specifications of these devices are not provided in this manual Should you require information about these devices please contact Hinds Instruments Inc directly Hardware 18 PM IRRAS Accessory Hardware Manual The PM IRRAS accessory is attached to the right side of an Agilent 600 Series FTIR spectrometer It is installed and aligned by your Agilent customer service representative Beam path
8. degrees e Detector at 70 75 degrees 4 In the Method Editor in Resolutions Pro set the following instrument parameters a Common Settings Resolution 8 cm 1 Basic Operation PM IRRAS Accessory Hardware Manual 25 b Collect Speed 25 KHz UDR 2 Filter 6 4 KHz Sensitivity 1 c Spectrometer Configuration IR Source Rear Mid IR Beam Path Right Detector Ext 1 Aperture 2 cm 1 Attenuator 50 5 Click Signal Monitor and rotate the test slide to optimize the interferogram signal 6 Select Single Beam while in Signal Monitor and check that the slide is correctly positioned Figure 5 shows a spectrum of the coated side and Figure 6 shows a spectrum of the glass side Figure 5 Single beam spectrum of the coated side of the test slide Basic Operation 26 PM IRRAS Accessory Hardware Manual Figure 6 Spectrum of the glass side of the test slide 7 Set up the PEM controller as follows refer to the PEM 100 controller manual for details a 7500 nm b Retardation 0 5 c Frequency 2F NOTE The PEM frequency may take several minutes to stabilize after it has been turned on or settings have been changed for example retardation amplitude or wavelength Allow the PEM to stabilize before starting data collection 8 To perform PM IRRAS measurements in step scan mode proceed to the next section
9. if applicable without warping or sagging The loaded flatness tolerance is 0 4 millimeter per 300 millimeters of length 1 64 inch per foot of length A minimum of 30 centimeters 12 inches of free space is required behind the spectrometer and PM IRRAS accessory An overhead space of 75 centimeters 30 inches is required Introduction 16 PM IRRAS Accessory Hardware Manual Installation requirements Before receiving your Agilent FTIR spectrometer and PM IRRAS accessory you will have been given a copy of the FTIR spectrometer Site Preparation Guide which describes the environmental and operating requirements of the spectrometer system You must prepare your laboratory according to these instructions before the system can be installed You should keep the pre installation manual for future reference If you have misplaced your copy you can obtain a replacement from your local Agilent office Training The software provided with your Agilent FTIR spectrometer includes an extensive Help applicable for the spectrometer and the PM IRRAS accessory If you require additional instruction or training contact your local Agilent office Documentation This hardware manual provides basic instructions for operating and maintaining your PM IRRAS accessory In addition to this manual you may receive other hardware and software manuals depending on the type of configuration purchased Further information and instructions about software
10. EM real 1500 1450 1400 1350 1300 1250 1200 1150 1100 1050 1000 950 900 4 0 3 5 3 0 2 5 2 0 1 5 Wavenumber Response Basic Operation 32 PM IRRAS Accessory Hardware Manual Data Collection in Rapid Scan Mode 1 Connect the hardware as shown in the schematic Figure 10 Schematic of cabling for rapid scan PM IRRAS measurement 2 Go to Collect gt Method Editor Select the following parameters a Common Settings Sample Scans 64 Resolution 8 cm 1 KEY External Detector Cable BNC Cable BNC Connector SPECTROMETER MCT LOCK IN AMPLIFIER 20 kHz HIGH PASS FILTER Ext 1 Signal Out User 5 2F Ref In CH1 Output Input A PEM CONTROLLER User 1 Basic Operation PM IRRAS Accessory Hardware Manual 33 b Collect Speed 12 5 KHz UDR 2 Filter 3 2 KHz Sensitivity 1 Interferogram Symmetry Asymmetric Signal User 1 Dual A D Collect checked c Spectrometer Configuration IR Source Rear Mid IR Beam Path Right Detector Ext 1 Aperture 2 cm 1 Attenuator 50 3 SR830 Lock in Amplifier a Time constant 30 s b Slope Oct 18 dB c Sensitivity 1 x 1 V variable d Reserve Normal e Signal Input Input connector A Coupling AC Ground Ground f Channel 1 Display X Ratio of
11. Go to Transforms gt Fourier Transforms Set Apodization Function TRIANGULAR and set Zero Function TRIANGULAR and set Zero Filling factor 4 and then click OK to compute the interferograms Spectrum 5 should look similar to Figure 8 dsp3 on fannie mae kevley udr4 pem 7500nm 2 128 0 45 0 40 0 35 0 30 0 25 0 20 0 15 0 10 0 05 700 600 500 400 300 200 100 0 100 Wavenumber Response Basic Operation 30 PM IRRAS Accessory Hardware Manual Figure 8 AC spectrum Ip Is 13 Select Spectrum 5 and go to Transforms gt Spectral Calculator gt Paired Spectra A Spectral Arithmetic Paired Spectra Operations dialog box will be displayed Select Divide by Reference Select Use Current and then select 1 Phase Modulation Real from the list of spectra in the bottom right corner Click Replace 14 Zoom in on Spectrum 5 between approximately 1500 and 900 cm 1 The spectrum should look similar to Figure 9 with a large broad peak around 1110 cm 1 and a weaker peak around 1265 cm 1 PEM real 3800 3600 3400 3200 3000 2800 2600 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 2800 2600 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 Wavenumber Response Basic Operation PM IRRAS Accessory Hardware Manual 31 Figure 9 Ratio of AC spectrum Ip Is to DC spectrum Ip Is 1265 5 1110 3 P
12. The infrared beam exits the spectrometer and is directed by two flat mirrors A and C in Figure 1 to the parabolic mirror D for focusing Figure 1 Agilent PM IRRAS accessory beam path with cover removed for clarity A Flat mirror B Beam from spectrometer C Flat mirror D Parabolic mirror E UDR filter F Polarizer G Photo elastic modulator H Angle Indicator I Sample J Detector J I H G D F E A B C Hardware PM IRRAS Accessory Hardware Manual 19 Filters The focused beam may pass through three optical elements before passing through the Photoelastic Modulator PEM As shown in figure 2 these elements are Infrared polarizer A in Figure 2 with the plane of polarization set parallel to the plane of incidence at the sample UDR filter B in Figure 2 location for UDR4 or UDR8 filter The UDR filters are optical lowpass filters which transmit below 3 950 cm 1 UDR4 filter or 1 975 cm 1 UDR8 filter and are used with the UDR 4 or UDR 8 parameter setting respectively of Resolutions Pro software Quartz window optional C in Figure 2 acting as a high pass optical filter transmitting above 2 000 cm 1 When used with the UDR4 filter see below allows data collection at UDR 8 for the bandpass between 3 950 and 2 000 cm 1 To display data in the required range click Transforms gt Fourier Transform gt Advanced and use the Included Frequency paramete
13. collection Data can be collected either in rapid scan mode or in step scan mode which uses DSP 3 software See the DSP 3 section in the Help Preparing the PEM IRRAS Power The PEM controller should be plugged into an AC alternating current outlet For power requirements refer to the PEM 100 User Manual Power for the detector is supplied from the FTIR spectrometer Detector cooling Fill the detector Dewar with liquid nitrogen for each detector to be used as described on Page 15 Basic Operation 24 PM IRRAS Accessory Hardware Manual WARNING Extreme Cold Hazard Liquid nitrogen is very cold and can cause damage to the human body Use appropriate protective equipment when handling liquid nitrogen Sample purge Turn on the purge if desired The purge fitting is in the back of the PM IRRAS accessory and accepts 6 millimeter OD tubing Set the purge rate to 13 liters per minute Scanning To set up and scan 1 Install the UDR4 filter and the Polarizer 0 deg should be at the top 2 Install the IR Reflective Test Slide in the sample holder on the rotary stage The coated side of the slide should be facing to the right in the beam path The coated side will be the side facing you with the etched corner in the upper right corner Set the angle of the slide at 90 degrees 3 Optical setup a PEM in beam path TURNED OFF b Polarizer in holder c UDR4 filter d IR Reflective Test Slide at 90
14. eam could be redirected out of the sample compartment resulting in on axis or direct viewing Care must be taken to avoid this Refer to the spectrometer hardware manual for more information about the laser Other precautions Use of the PM IRRAS accessory may involve materials solvents and solutions which are flammable corrosive toxic or otherwise hazardous Careless improper or unskilled use of such materials solvents and solutions can create explosion hazards fire hazards toxicity and other hazards which can result in death serious personal injury and damage to equipment and property ALWAYS ensure that laboratory safety practices governing the use handling and disposal of such materials are strictly observed These safety practices should include the wearing of appropriate safety clothing and safety glasses Safety Practices and Hazards 8 PM IRRAS Accessory Hardware Manual Warnings and cautions Carefully read all warnings and cautions and observe them at all times A Warning message is used in the text when failure to observe instructions or precautions could result in death or injury Warnings have the following format WARNING Hazard Type Nature of the hazard information on how to avoid the hazard and possible consequences if you don t The triangular symbols that appear in conjunction with warnings are outlined in the next section A Caution message is used when failure to observe instructions c
15. ectroscopy PM IRRAS accessory has been designed to comply with the requirements of the Electromagnetic Compatibility EMC Directive and the Low Voltage electrical safety Directive commonly referred to as the LVD of the European Union Agilent has confirmed that each product complies with the relevant directives by testing a prototype against the prescribed EN European Norm standards Proof that a product complies with the directives is indicated by The CE marking appearing on the rear of the product The documentation package that accompanies the product containing a copy of the Declaration of Conformity This declaration is the legal declaration by Agilent that the product complies with the directives and also shows the EN standards to which the product was tested to demonstrate compliance Safety Practices and Hazards PM IRRAS Accessory Hardware Manual 11 Electromagnetic Compatibility EN55011 CISPR11 Group 1 ISM equipment group 1 contains all ISM equipment in which there is intentionally generated and or used conductively coupled radio frequency energy which is necessary for the internal functioning of the equipment itself Class A equipment is equipment suitable for use in all establishments other than domestic and those directly connected to a low voltage power supply network which supplies buildings used for domestic purposes This device complies with the requirements of CISPR11 Group 1 Class A as
16. er precautions 7 Warnings and cautions 8 Information symbols 8 CE compliance 10 Electromagnetic Compatibility 11 The Polarization Modulation Infrared Reflection Absorption Spectroscopy PM IRRAS accessory has been carefully designed to be used as an accessory for Agilent FTIR spectrometers When used properly it provides an accurate fast flexible and safe analytical system If the equipment is not used in a manner specified by the manufacturer the protection provided by the equipment may be impaired Information on safety practices appear throughout the documentation both printed and online provided with your spectrometer Before using the PM IRRAS accessory you must thoroughly read these safety practices Observe all relevant safety practices at all times Cryogenic cooling Detectors used with your PM IRRAS accessory are cryogenically cooled The liquid nitrogen used in this process is extremely cold and can cause damage to the human body Use appropriate protective equipment when working with liquid nitrogen Safety Practices and Hazards 6 PM IRRAS Accessory Hardware Manual Electrical hazards The Agilent PM IRRAS accessory contains electrical circuits devices and components operating at dangerous voltages Contact with these circuits devices and components can cause death serious injury or painful electrical shock Good grounding earthing is essential to avoid a potentially serious electric shock hazard
17. escribed in this document are furnished under a license and may be used or copied only in accordance with the terms of such license Restricted Rights Legend If software is for use in the performance of a U S Government prime contract or subcontract Software is delivered and licensed as Commercial computer software as defined in DFAR 252 227 7014 June 1995 or as a commercial item as defined in FAR 2 101 a or as Restricted computer software as defined in FAR 52 227 19 June 1987 or any equivalent agency regulation or contract clause Use duplication or disclosure of Software is subject to Agilent Technologies standard commercial license terms and non DOD Departments and Agencies of the U S Government will receive no greater than Restricted Rights as defined in FAR 52 227 19 c 1 2 June 1987 U S Government users will receive no greater than Limited Rights as defined in FAR 52 227 14 June 1987 or DFAR 252 227 7015 b 2 November 1995 as applicable in any technical data Safety Notices A CAUTION notice denotes a hazard It calls attention to an operating procedure practice or the like that if not correctly performed or adhered to could result in damage to the product or loss of important data Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met A WARNING notice denotes a hazard It calls attention to an operating procedure practice o
18. f Expand off Output X Press CH1 OFFSET Auto before each measurement Basic Operation 34 PM IRRAS Accessory Hardware Manual g Reference Freq h Trig Pos Edge i Press AUTO Phase before each measurement 4 Click Signal Monitor 5 Press and hold CH1 OFFSET AUTO on the lock in amplifier to remove any DC offset from the interferogram 6 Adjust the sensitivity on the lock in amplifier to achieve an interferogram signal of 1 9 V 7 Unplug the BNC cable from User 1 and plug it back into User 5 8 On the Collect page of Method Editor make Signal AUTO 9 Click Scan 10 At the end of the collect two spectra called Signal Channel and Reference Channel will be added to the spreadsheet The Signal Channel corresponds to the AC spectrum Ip Is from the lock in amplifier The Reference Channel corresponds to the DC spectrum Ip Is 11 Select the Signal Channel spectrum in the spreadsheet and go to Transforms gt Spectral Calculator gt Paired Spectra A Spectral Arithmetic Paired Spectra Operations dialog box will be displayed Select Divide by Reference Select Use Current and then select the Reference Channel spectrum from the list of spectra in the bottom right corner Click Add 12 The resultant spectrum should look similar to that shown in Figure 9 on Page 31 Maintenance PM IRRAS Accessory Hardware Manual 35 5 Maintenance Cleaning 35 Fuses 36 Spare parts
19. ical circuits devices and components operating at dangerous voltages Contact with these circuits devices and components can cause death serious injury or painful electrical shock To prevent reduced safety protection or unwanted fusing ALWAYS ensure that fuses are only replaced with fuses of the correct type and rating To check a fuse 1 Disconnect the instrument from the mains power supply 2 Remove the fuse holder from the IEC mains power inlet connector with a small flat blade screwdriver 3 Check that the fuse is the correct type and is not damaged If necessary replace the fuse 4 Fit the fuse holder back into the IEC mains power inlet connector 5 Reconnect the instrument to the mains power supply NOTE If a fuse repeatedly blows it may indicate other problems with the accessory A service call may be required Spare parts For information about spare parts and their part numbers refer to the Agilent website www agilent com www agilent com In This Guide The guide describes the following Safety Practices and Hazards Introduction Hardware Basic Operation Maintenance Agilent Technologies 2010 2013 Printed in Malaysia 05 13 8510258800 8510258800 8510258800 Issue 5
20. ntrast absorption of s polarized light is virtually zero Therefore the dichroic difference spectrum is only sensitive to the thin film on the substrate allowing the surface signal to be digitized with high dynamic range In the lower path above the detector is low pass filtered to eliminate the high frequency PEM component providing the single beam DC spectrum of the substrate The final step of data processing is to ratio the AC to the DC spectrum to obtain the surface spectrum with high sensitivity and free from atmospheric contamination Basic Operation PM IRRAS Accessory Hardware Manual 23 In step scan mode the IR radiation is phase modulated by the interferometer typically at phase modulation frequencies of 400 or 800 Hz at an amplitude of 1 0 or 2 0 HeNe and stepping at 0 5 2 5 Hz The modulated radiation follows the same optical path as in the rapid scan measurement described above In step scan mode the optical low pass filters have dual purpose In addition to enabling higher throughput at frequencies of interest a major advantage is a reduction in collection time Although the optical arrangement is identical between step and rapid scan there is a significant difference in the way that the detector signal is processed In step scan mode unique digital signal processing DSP software within Resolutions Pro is used to replace the function of the LIA the electronic filters and the second A D converter Data
21. odes of collection for PM IRRAS measurements that is rapid scan or step scan In rapid scan mode broadband infrared radiation from a ceramic source is modulated by rapid scanning typically at 12 5 kHz of the interferometer in the spectrometer The modulated radiation is filtered with a low pass optical filter transmitting radiation below 3 950 cm 1 or 1 975 cm 1 The purpose of these low pass filters is to enable higher throughput at frequencies of interest After filtering the IR radiation is polarized by a wire grid polarizer The polarized IR beam is then modulated between s and p polarization at 74 kHz by the ZnSe PEM before reflecting off the sample at a grazing angle of incidence typically 80 to 85 from normal Most commonly the sample is a self assembled monolayer film on a metallic substrate such as gold The IR light is subsequently focused onto a narrow band MCT detector with on axis refractive optics After the detector and preamplifier the signal is sent along two parallel paths as displayed in Figure 4 In the top path shown in Figure 4 the signal is high pass filtered and then demodulated for polarization modulation by a Lock in Amplifier LIA The output of the LIA provides the dichroic difference spectrum between s and p polarized light often called the AC spectrum At large angles of incidence absorption of p polarized light by molecules adsorbed on a metallic surface is enhanced In co
22. ould result in damage to equipment Agilent supplied and or other associated equipment Cautions have the following format CAUTION Caution information appears here Information symbols The following triangular symbols appear in conjunction with warnings on the spectrometer and associated documentation The hazard they depict is shown below each symbol Safety Practices and Hazards PM IRRAS Accessory Hardware Manual 9 Broken glass Corrosive liquid Electrical shock Extreme cold Eye hazard Fire hazard Heavy weight danger to feet Heavy weight danger to hands Hot surface Laser hazard Moving parts Noxious gas The following symbol may be used on warning labels attached to the instrument When you see this symbol refer to the relevant operation or service manual for the correct procedure referred to by that warning label Safety Practices and Hazards 10 PM IRRAS Accessory Hardware Manual The following symbols also appear on the instrument or in the documentation I Mains power on 0 Mains power off Fuse Single phase alternating current When attached to the rear of the instrument indicates that the product complies with the requirements of one or more EU directives When attached to the rear of the product indicates that the product has been certified evaluated to CSA 61010 1 and UL 61010 1 CE compliance The Agilent Polarization Modulation Infrared Reflection Absorption Sp
23. ox should be set as follows Filter IN Frequency 74 KHz 7 Now do a Setup from PM IRRAS DSP 3 window Click the DSP Calibrate button When the calibration is complete click OK 8 Click Scan 9 When the scan is complete look at Spectrum 1 and 5 Both should be strong interferograms If either interferogram is weak or only noise then the actual PEM frequency must be calculated 10 To calculate the PEM frequency select Spectrum 11 Go to Transforms gt Fourier Transforms A Compute window will open On the General tab select Apodization Function Triangular Zero Filling Factor AUTO On the Advanced tab select Use Standard Processing Click OK Basic Operation PM IRRAS Accessory Hardware Manual 29 11 In the resulting spectrum there should be a strong peak at approximately 0 41 as shown in Figure 7 Multiply the peak location by 28571 Subtract this product from 85714 This result is the actual frequency of the PEM Enter this value for the PEM Frequency in Hz parameter and then click Scan again This value may be different than the value on the PEM controller display Note the difference between the calculated value and the displayed value This difference will be constant Figure 7 Spectrum of time based raw data for step number 75Error No bookmark name given 12 When the scan is complete select Spectrum 1 and Spectrum 5 12 When the scan is complete select Spectrum 1 and Spectrum 5
24. r Beam direction Figure 2 Infrared polarizer plane of polarization A Polarizer B UDR filter C Quartz window The filters and polarizers must be placed in the order as shown in Figure 2 Hardware 20 PM IRRAS Accessory Hardware Manual Orientation of sample and detector Mount the sample maximum sample size 75 mm in the optical clamp so that the clamp grips the edge of the sample The detector should be offset from 90 by twice the sample angle The beam exits the PEM along the 90 line Typically the sample should be set along the 80 line 10 offset and the detector set at 70 20 offset The detector position may be optimized by maximizing the magnitude of the interferogram centerburst in rapid scan setup mode while making small adjustments of the detector angle The ZnSe lens assembly has been optimized on installation Do not adjust the lens relative to the detector Figure 3 Sample and detector orientation A Detector B Angle indicator C Sample A B C Basic Operation PM IRRAS Accessory Hardware Manual 21 4 Basic Operation Introduction 21 Data collection 23 Preparing the PEM IRRAS 23 Data Collection in Step Scan Mode 27 Data Collection in Rapid Scan Mode 32 Introduction A schematic diagram of a PM IRRAS experiment is shown in Figure 4 Figure 4 Schematic diagram of an IRRAS experiment Basic Operation 22 PM IRRAS Accessory Hardware Manual Agilent provides two m
25. r the like that if not correctly performed or adhered to could result in personal injury or death Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met CAUTION WARNING Safety Practices and Hazards PM IRRAS Accessory Hardware Manual 3 Contents 1 Safety Practices and Hazards 5 Cryogenic cooling 5 Electrical hazards 6 Laser safety 6 Other precautions 7 Warnings and cautions 8 Information symbols 8 CE compliance 10 Electromagnetic Compatibility 11 EN55011 CISPR11 11 ICES NMB 001 12 2 Introduction 13 Specifications 13 Environmental 13 Power 14 Purge gas 14 Liquid nitrogen 15 Weights and dimensions 15 Space 15 Installation requirements 16 Training 16 Documentation 16 Safety Practices and Hazards 4 PM IRRAS Accessory Hardware Manual 3 Hardware 17 Overview 17 Beam path 18 Filters 19 Orientation of sample and detector 20 4 Basic Operation 21 Introduction 21 Data collection 23 Preparing the PEM IRRAS 23 Power 23 Detector cooling 23 Sample purge 24 Scanning 24 Data Collection in Step Scan Mode 27 Data Collection in Rapid Scan Mode 32 5 Maintenance 35 Cleaning 35 Fuses 36 Spare parts 36 Safety Practices and Hazards PM IRRAS Accessory Hardware Manual 5 1 Safety Practices and Hazards Cryogenic cooling 5 Electrical hazards 6 Laser safety 6 Oth
26. radiation professional equipment Therefore there may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbances Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try one or more of the following measures 1 Relocate the radio or antenna 2 Move the device away from the radio or television 3 Plug the device into a different electrical outlet so that the device and the radio or television are on separate electrical circuits 4 Make sure that all peripheral devices are also certified Safety Practices and Hazards 12 PM IRRAS Accessory Hardware Manual 5 Make sure that appropriate cables are used to connect the device to peripheral equipment 6 Consult your equipment dealer Agilent Technologies or an experienced technician for assistance 7 Changes or modifications not expressly approved by Agilent Technologies could void the user s authority to operate the equipment ICES NMB 001 This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme la norme NMB 001 du Canada
Download Pdf Manuals
Related Search