Thermocouple Process Calibrator AX-C830
Contents
1. AXIO i Hii MET Thermocouple Process Calibrator AX C830 User s Manual Safety Information To avoid possible electric shock or personal injury Never apply more than 30V between any two jacks or between any jack and earth ground Make sure the battery door is closed and latched before you operate the calibrator Remove test leads from the calibrator before you open the battery door Do not operate calibrator if it is damaged Do not operate the calibrator around explosive gas vapor or dust To avoid possible damage to the calibrator Make sure you choose the right jack and range before you use the calibrator to measurement or calibrator Take away the calibrator from the used circumstance before operate the calibrator or after close the calibrator Introduction Thermocouple Process Calibrator is a exactitude measurement and source handhold instrument it can be used to calibrate the Thermocouple instrument Thermocouple Process Calibrator can measure or simulate 8 types of difference Thermocouple C or F and measure or simulate the millivolt But it cannot be used for measurement or source at the same time The accessories 2 pcs Thermocouple plugs no wire 6 AAA 1 5V battery user s manual If the Calibrator is broken or short of some accessories please contact the supplier The following table has showed the technical parameter and function of the Calibrator Specification All the specificati2. nt Panel The front panel is show as in right figure an Input jack 2 Output jack 3 Power key 4 Mode key 5 C F key 6 Input output key 7 Increase more value key 8 Reduce more value key 9 Increase less value key 10 Reduce less value key 11 Low power indication 12 Input state indication 13 Output state indication 14 Reading value 15 Unit indication 16 Mode indication Operation Instructions Thermocouple or Millivolt measurement input CDPress the power key 3 turn on the calibrator Press the Input output key Press mode key 4 on the measure type you want Put the measure thermocouple or millivolt source into the input jack 1 5 Get the reading value 14 ES En INPUTOUTPUT K BBABA Vy w Ww Qe 6 when on the input mode INPUT The number in the a referring to the Explanation on Front Panel Page7 WWW AXIOMET EU J ZJ Thermocouple or Millivolt Simulate output r OUTPUT CDPress the power key 3 turn on the calibrator l n n n n Press the Input output key 6 when on the output mode LI L LILI TYPE J Press mode key 4 on the measure
3. on will under 1 year calibration cycle and temperature between 18 28 C except addition explain Measure input Simulate output Millivolt specification HINI WWW AXIDMET EU INPUT OUTPUT RANGE RESOLUTION ACCURACY 10mV 75mV 0 025764 2counts Maximal input voltage 30Vpp Measure input Simulate output Thermocouple Specification FUNCTION 200 1200 C 328 2192 F 200 1370 C 328 2498 C 200 400C 328 752 F 200 950 C 328 1742 F 20 1750 C 4 3182 F 20 1750 C 4 3182 F 600 1800 C 1112 3272 F 250 1300 C 418 2372 F Maximal input voltage 30Vpp REFERENCE RESOLUTION ACCURACY JUNCTION ERROR BN B BN B WWW AXIDMET EU General Specifications Maximum voltage applied between any jack and earth ground or between any two jack 30V Storage temperature 40 C 60 C Operating temperature 0 C 50 C Operating altitude 3000 meters maximum Temperature coefficient 0 02 C on 0 C 18 C and 28 C 50 C Relative humidity 95 up to 30 75 up to 40 45 up to 50 Shock Random 2g 5Hz to 500Hz Safety 1 meter drop test Power requirements 6 x AAA 1 5V battery Size 205mmx98mmx46mm Weight 472 g include battery International Symbols l Earth ground Conforms to European Union directives Refer to this instruction sheet for information about this feature Battery Double insulation Explanation on Fro
4. type you want ER MMM Press the adjust value key 7 B 9 0 to let the value f UN S on your need mai Put the thermocouple instrument or voltage meter into the output jack 2 Ef you want to change the output value then press the adjust value key 7 8 9 10 or change to other thermocouple type use the mode key 4 The number in the a referring to the Explanation on Front Panel Page7 Maintenance Cleaning Periodically wipe the case with a damp cloth and detergent do not use abrasives or solvents Calibration Calibrate your calibrator once a year to ensure that it performs according to its specifications Replacing the Battery Please change the battery when the LCD indicates as Turn off the power of the Calibrator before you change the battery and screw off the breechblock on the battery cabinet cover then take it off and put the fresh AAA 1 5V battery Connect wire Use the accessories thermocouple plug to make the difference plug connect wire which you want HINI WWW AXIDMET EU
Download Pdf Manuals
Related Search