USER`S MANUAL - BTD Car Tools
Contents
1. CAR TOOLS LTD www btd cartools com USER S MANUAL For BTD E 2 8 KEEP THE MANUAL NEAR THE MACHINE ALL TIME AND MAKE SURE ALL USERS HAVE READ THIS 2 8 Ton Movable Scissor Lift MODEL NO FOLLOW THE INSTRUCTIONS CAREFULLY TO GRANT THE BTD E 2 8 MACHINE CORRECT FUNCTION AND LONG SERVICE LIFE CAR TOOLS LTD www btd cartools com Daily Maintenance 1 Insure all bolts are secured and snug with lock washer nylon lock nuts or cotter keys 2 Lift locking mechanism should be lubricated to operate properly 3 Check spring on locking mechanism for constant tension 4 Check cylinders and hose for loose connections and leaks 5 Check oil level in pump reservoir Operating Tips 1 DONOT attempt to lift more than the units rated capacity 2 Lift should only be operated on a level foundation 3 Remove any potential obstacles that might impede roller travel 4 The machine or vehicle that is being lifted should be balanced on the lift 5 Do not remove heavy components from a raised machine or vehicle without first installing adequate supports The vehicle may become unbalanced and fall On Site Assembly Instructions 1 Mount motor and pump to power unit stand with 4 bolts supplied with the lift 2 Mount the 3 8 hydraulic hose to 3 8 adapter located on the lower end of the hydraulic splitter See Fig 2 Fill reservoir tank with hydraulic oil SAE 10 weight non foaming non deter2. Lift mechanism does not move up and down smoothly Move vehicle location on the lift for more equal weight distribution Bleed the hydraulic system by first loosening the hose connection at the rod end of both cylinders Then loosen the hose from fitting NOT the fitting from the cylinder Run the Power unit until fluid appears at the hose and fitting connection and hose connection at the rod end When there is no more air exiting the System tighten both hose connections 4 Lift does not lift its rated capacity Move vehicle location on the lift for more equal weight distribution Check the voltage of the electrical supply with the unit run under load Make sure the pump is getting adequate voltage 5 Cylinders leak under rated load Check for leaks at the hydraulic hose fittings cylinders and pump Contamination may be in the check valve preventing the valve from completely closing 1 Hold open the lowering valve by pushing the control lever on the power unit 2 Atthe same time run the pump for 30 seconds to flush the valve 3 Repeat 3 to 4 times 4 If cylinders continue to leak down pump may have a faulty Valve Contact the manufacturer CAR TOOLS LTD www btd cartools com 6 Lift will not lower Raise lift 1 tO 2 squeeze release handle and try again to lower lift Rack localization locking the height is adjustable more safe by machine locking Check tension the relea
3. C27 30C NT CAR TOOLS LTD www btd cartools com FAY lt 23153420 gt 33 FIG 1 CAR TOOLS LTD www btd cartools com 13 17 4130 41 FIG 2 TOOLS LTD Installation photo 1367 270 324 2062 www btd cartools com 1059 10 164
4. gent and plug into 110 volt AC power source 3 The lock release cable should already be installed at the lock end of the lift CAR TOOLS LTD www btd cartools com Attach the other end of the lock release cable to the brake handle and mount to the power unit stand handle Specifications Lowered Height 37 8 Voltage 110VAC Raised Height 48 Motor Output 1HP Overall Width 39 1 2 Pump Output 3200 psi Overall Length 88 Fluid Capacity 6 at Lift Capacity Scale This is what the lift pick up with weight directly on the lifting pads at the specified distances from the floor 1 500 Ibs Scissor lift platform fully retracted with no spacer on the platform attachment bolts 3 000 Ibs Scissor lift platform is raised 11 2 distance from the floor with provided spacer on platform attachment bolts 4 000 Ibs Scissor lift platform is raised 2 1 2 distance from the floor requires additional spacer 5 000 Ibs Scissor lift platform is raised 3 3 8 distance from the floor requires additional spacer 6 000 Ibs Scissor lift platform is raised 4 3 8 distance from the floor requires additional spacer Troubleshooting 1 Pump motor will not operate Check electrical plug and cord Check electrical supply breaker 2 Power unit switch does not operate properly Contact the manufacturer for a replacement or Additional troubleshooting information CAR TOOLS LTD www btd cartools com 3
5. se cable Provides four request pad body the height is adjustable and may 360 degrees rotations CAR TOOLS LTD www btd cartools com C 27 PARTS LIST ITEM JPN _ 3 PN 7 13 17 23 27 G QIN 30 68923 88 ____ NUTOMM 31 6867 85 SLOTEDNUTOMMx10 1 32 6896 85 WASHER GB5782 86 BOLT 16 80 Nl 8 8 34 GB T889 86 NYLONLOCKNUT16MM 1 35 6870 85 BOLT _ 2 36 685781 86 BOLT 8MMx20MM _ 5 37 6870 85 BOLT 5MMx16MM _ 1 CAR TOOLS LTD www btd cartools com GB77 85____ BOLTSMM 16MM 39 C2730 SAFETYRELEASECABLE 1 _ YG03 9100 CYLNDER 2 GB9585 FLATWASHER 2 a2 c27150 4 42 C27 130 LIFTING PADS SADDLE 2 LIFTING PADS 02721 HYDRAULICHOE 2 EE 51053 1800 DOLLY 51053 1811 HANDLE 2 4433 C27 30 SAFETY RELEASE HANDLE 1 44 4 6891 36 SPLITPIN3MMx30MM_ 2 gie G89I8186 446 __ casters____ GB97 1 85 SADE 6 448 30400 9053YZ 1 carmo TOPPLATFORM 47 889 86 NYLONLOCKNUT18MM 4 49 627 58 __ 4 524 0 5297_ 3 GB41 86 NT 60 738 CABLEADJUSTBOLT ___ 1 61
Download Pdf Manuals
Related Search