Installafion and Operafion
Contents
1. HQ GHRISE Installation and Operation Handi Quilter Designed by a Quilter for Quilters Copyright 2013 Handi Quilter Inc All rights reserved Printed in the U S A 08 2013 Table of Contents Contents of the HQ HighRise kit 3 Installation 6 Operation of the HQ HighRise 12 Troubleshooting 15 2 HQHigh Rise Instructions 08 26 13 www HandiQuilter com Contents of the HQ HighRise kit The HQ HighRise works with the straight leg HQ Studio Frame and HQ Fusion Frame systems Be sure to verify that you have the straight leg frames and not the slanted legs on your frame Item Part Number s Quantity Photo A actuators with cable QT10800 6 labeled 1 6 B saddle brackets QT10817 6 C top left brackets QT10815 6 2 ik D top right brackets QT10816 6 A E extension cables QT20110 170 5 4 labeled 3 6 of different lengths QT20110 146 6 QT20110 113 4 QT20110 65 3 F controller with QT20105 1 mounting plate www HandiQuilter com 08 26 13 HQ High Rise Instructions 3 Item G power supply H power cord cable ties J adhesive tie wrap pads K fir tree plugs L cable sheath M M6 x 55mm screws 4 HQ High Rise Instructions Part Number s Quantity QT20110 1 QM20277 1 not applicable 18 not applicable 12 not applicable 4 not applicable 2 QT10813 6 08 26 13 Photo www HandiQuilter com Item Part Number s Quantity Photo N M6 x 50mm screws Q2. a Fusion Frame the center legs have two vertical posts Mount the actuator behind the front post of Front of 4 foot each center leg NOTE The controller can be mounted on the left side or the right side of the frame These instructions show photographs for mounting the controller on the right side of the frame If you mount the controller on the left side of the frame reverse the actuator numbers and positions e g put actuator 1 on the back left side leg put actuator 2 on the front left side leg etc However you should still connect the cables into the controller according to their numbers as described later www HandiQuilter com 08 26 13 HQ High Rise Instructions 7 To mount the actuators to the frame s legs Follow steps 1 through 7 to mount each actuator required for the size and configuration of your frame 1 Place the bottom saddle bracket over the inside bottom frame tube with the motor side of the actuator facing away from the leg Motor Saddle bracket 2 Tilt the bottom of the actuator saddle bracket end away from the leg and place the right and left top brackets around leg and over the top of the motor end of the actuator 3 Insert a M6 x 50mm screw between the right and left top brackets and Loosely fasten loosely fasten the right and left top brackets 4 Insert four M6 x 16mm screws to clamp the right and left top brackets together around leg tube and loosely fasten Loosely faste
3. T10819 6 O M6 x 35mm screws QT10812 6 P M6 x 16mm screws QT10811 24 Q wireless key fob QT20108 1 IMPORTANT The key fob has been synchronized with your controller It will not work with another HQ HighRise controller Tools required e Screwdrivers Phillips screwdriver and flat blade screwdriver e Small adjustable wrench e 5mm hex wrench or if available a 5mm hex head drill bit mounted in a cordless drill Level optional Isopropyl alcohol to wipe the frame before attaching adhesive tie wrap pads www HandiQuilter com 08 26 13 HQ High Rise Instructions 5 Installation To prepare the frame legs for the HQ HighRise 1 Lower the frame to its lowest position IMPORTANT Before proceeding make sure the frame is level from front to back and from side to side Use a spirit or bubble level if you have one available If you need to adjust the leveling feet on the frame use the 17 13 16mm wrench that came with your frame 2 Remove the frame s leg latches Use a 3 hex wrench and an adjustable wrench or 5 16 inch socket wrench to remove all of the leg latches CAUTION Be careful when removing the screw because the spring is under a slight tension IMPORTANT Keep the leg latches springs and screws in case you need to remove the HQ HighRise system To prepare the actuators for installation Mount the saddle bracket to the non motor end of all six actuators with M6 x 35mm screws Slide the screw through t
4. ame e Press and hold the green up button until the frame raises to your desired height It will be at its maximum height when all eight LEDs are lit and motion has stopped because the frame can t go any higher e Alternately press and hold the top button on the key fob for longer than one second and until the frame raises to your desired height To lower the frame e Press and hold the blue down button until the frame lowers to your desired height It will be at its lowest position when a single LED is lit and motion has stopped because the frame can t go any lower e Alternately press and hold the bottom button on the key fob for longer than one second and until the frame lowers to your desired height To customize the three preset frame heights Preset three frame heights and quickly recall a height by pressing one of the preset buttons 1 Set the frame to the desired height using the up green and down blue buttons 2 Press and hold one of the three preset buttons for two to three seconds The LED above the button will blink then the LED will stay illuminated indicating the button is programmed 3 Repeat these steps for the other two buttons with two other preset frame heights To recall a preset frame height e Quickly press one of the preset height buttons The HQ HighRise will adjust the frame to the preset height www HandiQuilter com 08 26 13 HQ High Rise Instructions 13 To use the wireless key fob The ho
5. d One or more actuator s have stopped lifting or lowering the table Actuators raise or lower the table with an uneven nonlevel motion www HandiQuilter com 08 26 13 Corrective Measure Fault LED red is illuminated Look at the lift height LEDs The illuminated LED indicates which actuator has a fault The bottom LED corresponds to actuator 1 the second LED from the bottom corresponds to actuator 2 and so forth for the bottom six LEDs Disconnect the power cord from the wall socket and check all of the cable connections including the exten sion cables Reconnect the power cord If the red fault LED is no longer illuminated try to raise or lower the frame If the red fault LED comes on disconnect the power cord from the wall and call Handi Quilter technical support One or more of the actuators or extension cables is not plugged in Disconnect the power cord from the wall socket and check that the cables are plugged into the correct connectors on the controller See To connect cables and power supply and the two notes marked IMPORTANT on page 8 for more information Reconnect the power cord and confirm that LED 7 and the fault LED are no longer illuminated Stop pressing buttons on the controller Disconnect the power cord from the wall socket and call Handi Quilter technical support Stop pressing buttons on the controller Disconnect the power cord from the wall socket and call Handi Quilter technical suppor
6. he flat hole on the bracket then through the opening on the actuator and out through the hole on the other side of the bracket tightening as you go Motor The number of actuators you will install to the frame depends on the size and configuration of your frame e f you have a 12 foot frame or a 10 foot frame use all six actuators numbers 1 through 6 one each on the front and back of the side legs and one on each of the center legs e f you have an 8 foot frame or a 6 foot frame use five actuators numbers 1 2 3 4 and 5 one each on the front and back of the side legs and one on the center leg e f you have an 4 foot frame use four actuators numbers 1 2 3 and 4 one each on the front and back of the side legs 6 HQ High Rise Instructions 08 26 13 www HandiQuilter com Use the following diagrams to determine which actuator to mount to each leg of the frame Lay each of the prepared actuators next to the leg to which it will be mounted and double check before proceeding Actuator 5 Actuator 1 Actuator 6 Actuator 2 Actuator 4 Actuator 3 Actuator 4 mounted behind left center leg Front of 12 foot or 10 foot frame Actuator 4 Actuator 1 Actuator 5 Actuator 2 Actuator 3 Front of 8 foot or 6 foot frame Actuator 3 Actuator 1 Actuator 4 Actuator 2 Actuator 3 mounted behind right center leg IMPORTANT The photograph above shows the Studio Frame If you have
7. le indicates the top of the key fob Press and hold for longer than Quickly press to move the a second to frame to preset height A raise the frame Quickly press to move the frame to preset height B Press and hold for longer than a second to lower the frame Quicly press to move the frame to preset height C To use the key fob to raise or lower the frame e Press and hold the top button for longer than a second to raise the frame When the frame is at the desired height release the button e Press and hold the bottom button for longer than a second to lower the frame When the frame is at the desired height release the button To use the key fob to adjust the frame to a preset height e Quickly press one of the buttons on the key fob The HQ HighRise adjusts the frame to the preset height The top button adjusts the frame to preset height A the middle button adjusts the frame to preset height B and the bottom button adjusts the frame to preset height C AY NOTE When the actuators are extended there may be a small amount of oil on the inside actuator tube This is normal Keep fabrics and other objects away from these inside tubes 14 HQ High Rise Instructions 08 26 13 www HandiQuilter com Troubleshooting Your HQ HighRise requires no maintenance Troubleshooting Problem or Symptom Fault LED red is illuminated Fault LED red is illuminated LED 7 second lift height LED from the top is illuminate
8. n the four 30mm Screws 8 HQ High Rise Instructions 08 26 13 www HandiQuilter com 5 Push the bottom of the actuator so the actuator is parallel to the leg 6 Fully tighten all screws 7 Insert a M6 x 55mm screw under the bottom frame tube and tighten 8 Repeat steps 1 through 7 for each actuator you install To lay out and connect the cables 1 Lay out extension cables 5 longest 6 next longest 4 and 3 PADER on the floor behind the frame Make sure the cables are oriented such that the connector i ends can be plugged into the actuators 2 Connect the numbered extension cables to the 5 6 4 and 3 actuator cables If youa re using fewer actuators connect extension cables to only those actuators 3 Pull the other ends of extension cables over to the right front side of the frame They will be connected to the controller later in the setup www HandiQuilter com 08 26 13 HQ High Rise Instructions 9 To mount the controller to the side of the frame 1 Remove the front poles from the frame s pole brackets 2 Useasmall adjustable wrench to remove two bolts from the front right side of the pole brackets 3 Insert the bolts you just removed through controller s mounting plate and place the bolts back into the front right side of the pole brackets Tighten the bolts To connect cables and power supply 1 Connect the 1 and 2 actuator cables to labeled connectors 1 and 2 on the c
9. ontroller 2 Connect extension cables 3 4 5 and 6 to labeled connectors on the controller Connectors 7 and 8 are open nothing connected 3 Lay the power supply inside the right front bottom frame tube 4 Connect the power supply cable to the controller Wrap the power supply cord around the front right leg and use cable ties to secure the power supply cable near the controller Ensure there is sufficient slack in the cable to allow for raising the frame 5 Connect the power cord to the back of the power supply 10 HQHigh Rise Instructions 08 26 13 www HandiQuilter com 6 Use one piece of cable sheath to bundle cables 1 2 and 3 connected to the controller Trim the sheath if necessary with a pair of scissors 7 Use one piece of cable sheath to bundle the cables 4 5 and 6 connected to the controller NOTE Trim the sheath to appropriate length if necessary with scissors 8 Pull the cables with sheaths behind and underneath the right upper frame tube and push a fir tree plug into any empty screw hole and then use a cable tie to secure the cable bundles 9 Use adhesive tie wrap pads and cable ties to secure cable bundles to the back of the frame NOTE To ensure good adhesion wipe the frame with isopropyl alcohol and allow it to dry before sticking the adhesive tie wrap pad www HandiQuilter com 08 26 13 Fir tree plugs in serted into open screw holes in the frame Cable ties in
10. serted into a tree plugs and then wrapped around cables HQ High Rise Instructions 11 Operation of the HQ HighRise The HQ HighRise is simple to operate Lift height LEDs Raises the frame to its maximum height Set three pre set heights Then select the button for ra the the an you rame to its want lowest position Fault LED Red First time operation 1 Plug in the power cord from power supply to an outlet At least one LED on the controller will light indicating power is on 2 Press the green up arrow button for a few seconds All actuators should lift If not refer to the troubleshooting section of this manual 3 Press the blue down arrow button for a few seconds All actuators should lower If not refer to the troubleshooting section of this manual Your HQ HighRise is now operational AN caution When the actuators are extended there may be a small amount of oil on the inside actuator tube This is normal Keep fabrics and other objects away from these inside tubes iN NOTE When the actuators are extended there may be a small amount of oil on the inside actuator tube This is normal Keep fabrics and other objects away from these inside tubes IMPORTANT The actuators have a 10 duty cycle which requires that the HQ HighRise is not operated constantly The actuator motors may overheat if the system is run constantly 12 HQ High Rise Instructions 08 26 13 www HandiQuilter com To raise the fr
11. t HQ High Rise Instructions 15
Download Pdf Manuals
Related Search