HDMI Switch Box
Contents
1. switcher User s Manual ILLUSTRATION Front Panel MONOPEICE Homi HD 411E3 LEC LEE POWER SELECT Rear Panel e DC5V OUTPUT CONNECTION ILLUSTRATION HDTV Display Blu ray DVD DVD Recorder Power Adaptor Satellite Receiver Home Theater CONNECTION amp OPERATION Connection Step 1 Connect the HDMI cables from the HD sources PS3 DVD player to the input ports of the HDMI Switcher Step 2 Connect the HDMI cable from your HD display HDTV or projector to the output port of the HDMI Switcher Step 3 Connect the 5VDC power adaptor to the HDMI Switcher Step 4 After you finish the connection the power indication LED red CEC indication LED blue and port 1 input indication LED green will be lighted on 2 Step 1 2 5 Initiate the CEC communication Turn on the connected TV Switch box and all connected source devices Select the source devices one by one and make sure all source devices are working correctly Audio and video correctly show on TV with no interruption or noise 3 Follow the operational instruction below and try all the operation function include CEC 4 Note 1 control function Routing Change One Touch play Standby If any function can not work please restart the switcher and perform Step 5 again Initiate the CEC communication can make sure the switcher collect the correct EDID information from source device and displ2. the cable connection was changed please re initiate the CEC communication Please follow Step 5 of the connection instruction on page 3 Please make sure the CEC function can work correctly when the source device is connected directly to the display device TV f you operate the CEC function when the DVD or Blue ray player playing mandatory non skip part video ex Copy right warning it may cause the CEC not working properly Please turn off the player and restart the player The CEC functions may not totally work under different brand device Because each brand may have their own special control features It is suggested to choose same brand devices in order to support full CEC features of each brand s CEC control NOTICE Manufacturer reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC HD 411E3 incorporates HDMI M technology
3. MONOPRICE HDMI Switch Box HDMI CEC Supported _Z 4 inputs 1 output Model HD 411E3 INTRODUCTION Congratulations on your purchase of the HDMI Switcher Your satisfaction is very important to us Our series of HDMI Switchers are designed to make the use of your HDTV equipment more comfortable HD 411E3 Switcher can expand HDMI input of your HDMI display device up to 4 HDMI inputs The Switcher offers single cable connection solution to TV instead of connecting 4 HDMI cables to your HDTV You will find this is a useful application when you try to hang a TV on wall The switch box can support HDMI CEC function and compliant with your CEC enable devices You can enjoy the convenience of CEC features without the interruption from switch box FEATURES AND CONTENTS For the best performance of this switch box please read this manual carefully and keep it for further information Features HDMI CEC Supported Expand 4 HDMI sources on your HDTV devices or Home Theater system Support 1080P 12 bit Deep color HDTV Support Pixel clock rate upto 225 MHz HDCP Compliant DTS HD Dolby TrueHD lossless compressed digital audio Compliant Gold plated connectors IR Remote Control Switch box CEC function enable disable control HDMI CEC functions supported Routing change One touch play Stand by Pass through CEC commands Content of Package 5V DC 1A power adaptor Remote control unit HDMI 4 IN 1 OUT
4. ay device Incorrect EDID information may cause failure of CEC function Due to varied design of CEC device some CEC devices will automatically initiate the CEC communication with the switcher The following condition is recommended to initiate or re initiate the CEC communication When you first use the HDMI Switcher with your CEC enabled device f you disconnect or change the cable connection order of the connected HDMI source devices f you connect the output of switch box to another TV set Please check the step 5 in the connection instruction The CEC is working under standby mode for all connected CEC supported devices only Please make sure the power of all CEC supported devices are plugged in and under standby mode The CEC feature only works with CEC supported devices Consumer Electronics Control CEC is also known as in following terms by their respective Brand Name Philips EasyLink Sony BRAVIA Theatre Sync Samsung Anynet LG Simplink Sharp Aquos Link Panasonic HDAVI Control EZ Sync and VIERA Link Pioneer Kuro Link Toshiba CE Link and Regza Link Onkyo RIHD Remote Interactive over HDMI Mitsubishi NetCommand Each brand may have its extend CEC fractures Under standby mode the HDMI switcher will memorize the latest input port At your next use the HDMI switcher will detect and connect the latest input port first To reset the switcher please unplug the power adaptor or unplug the po
5. nel 1 the CH1 LED will light on gt CH1 CH2 gt CH3 PCH4 TROUBLE SHOOTING 1 When there is no picture present please Make sure the direct connection from the source device to the display device without the HDMI Switcher is working Check all connectors connect well or not Check the connecting cable is damaged or not Check the power of HDMI Switcher or reset the switcher 2 When there is only picture displayed and without sound Check the cable connection to see if it fits properly Check your cable to see if it supports video transmission only DVI or it is damaged HDCP may not match very well at first connection please reset your HDMI switcher Do you connect any output to your Video recorder HDCP will lock up audio part 3 When resolution could not show in 1080p Make sure your sources HD DVD Player and displays are fully supporting 1080p Make sure your HDMI cables are capable of transmit 1080P video signal 4 When CEC function is not working properly Please make sure the blue CEC LED light is on If not you can use the remote control to turn on the CEC function or unplug the power cord to restart the switcher Please check if the connected source and display devices support HDMI CEC function Please make sure the CEC function of connected source and display devices is enabled Please re initiate the CEC communication Please follow Step 5 of the connection instruction on page 3 f
6. t Due to varied design of CEC device the status of previous source device DVD may change to pause continue to play or turn to standby Enable and disable the CEC function of the switcher Use the CEC button on the remote controller to enable or disable the CEC function of the switcher The original setting is CEC enabled A blue LED light will indicate the status Unplug the power and restart the switcher the switcher will be set to the original setting Users may also enable and disable the CEC function from their CEC devices TV DVD player Blue ray player Please check user s manuals of the CEC devices IR Remote operation Use the power key on the IR remote to power on the HDMI switcher the power indication LED on the front panel will be lighted on Press the power key one more time to turn the switcher to standby Use number buttons to switch between sources Use the CEC button on the remote controller to enable or disable the CEC function of the switcher Manual Operation The POWER SELECT key is a multi function key Press the button for 2 seconds to turn off the power Standby Press the POWER SELECT key once to turn on the switcher If you want to change the input channel manually you can only press the key once There will be a LED for channel indication The procedure is a cyclic function When you selected the channel there will be a LED on to present the channel If you select chan
7. wer cord from DC jack for 10 seconds or longer and then plug it back CEC operation Power ON OFF amp Input Port Selection Power on the CEC supported source device DVD The Switcher will power on and select to the proper input port If the TV set is in standby mode the TV CEC supported will power on and change to correct HDMI input port If you are watching from none HDMI source the TV will change to correct HDMI input port One Touch Play Power on and play other HDMI source devices CEC supported which is connected to the switcher box the switcher will change the input source to the newly active device Routing Control Power off standby the TV CEC supported The switcher and all source devices will turn to standby mode Standby Note If the source devices do not support CEC function the source devices will not turn to standby mode automatically All other CEC control features between source device and display device will be passed through Please check the manual of your CEC devices for CEC operations CEC functions may also support One Touch Record Deck Control Tuner Control Remote Control Pass through and more If you like to perform these CEC function above please check your display and source devices can both support the CEC functions Switch between different CEC supported source devices When you turn on and play on the selected device the switcher will automatically switch to the selected input por
Download Pdf Manuals
Related Search