User manual - Hjelpemiddeldatabasen
Contents
1. Stage 7 Adjusting the abdominal support on the front part Once the front part has been fitted on its holder No 1 and the rider is sitting against the backrest loosen the upward and downward knurled knobs No 6 and swivel the two elements holding supporting strio No 2 to place the strip at the level of the rider s pelvis Retighten knurled knobs No 6 after making the adjustment Pull out the longitudinal adjusting knobs No 5 and slide support strip No 2 to bring it into contact with the rider s pelvis lower abdomen To provide correct positioning and support the surface of abdominal support No 2 must come into contact at the level of the rider s pelvis but without pressing on it too hard Leave a finger s width between the strip and the rider s lower abdomen Release knobs No 5 in the corresponding locking holes once the adjustment has been made Upward and downward adjustments knurled knobs No 6 and front rear adjustments knobs No 5 of strip No 2 can be made asymmetrically on the right hand and left hand sides to provide optimum support i Abdominal i support strip Longitudinal Knurled upward downward adjustment 4 6 adjustment knob knob Figure 8 Details of the front part Before use check that the abdominal support strip is securely locked in place by pulling it gently upwards and pushing it backwards and forwards Locking knob es A a 5 Fae a k i j 7 j f Sl2. Spare parts efso moa E Knuriedknob VS0FOP 67 Restrictions of use Precautiol Made in France Some parts swivel and may cause pinching Saddle module for use as a horse riding aid Check the condition of the module fastening strap very frequently In the event of wear replace it before subsequent use The task of fitting the device on the saddle must be carried out by professional riding Description personnel The presence of accompanying persons is necessary to enable disabled people to go riding Use of a suitable transfer method mounting block or rider lifter is strongly recommended to The module is made up of two main elements the front part abdominal support and handle and enable these people to mount a rear part backrest Never modify any elements of the module structure Foruseona pon saddle putine ginh through ihe slet The unit is held in place by a fastening system that goes under the saddle to hold the two parts in place ppolib_02 2014_Photos non contractual_Printed on FSC certified paper gt lt g Girth slot Cleaning Storage m Store the product in a dry place Do not soak it Sige X Aw amp m Dry clean Use a damp cloth to clean the leather ron and metal parts I Use chlorinated products Z m The covers can be removed and washed Machine dry N at 30 C FSC Guarantee The guarantee covers a one year period provided that the module is used in complian
3. Montage du module sur la selle To watch a video showing how to fit the device on the saddle http www youtube com watchev jEn3mM8Ok4 Fit the module before saddling the horse Slide rod No 4 on the front part along the groove between the two pads under the saddle seat see figure 2 until hooks No 7 come up against the front of the saddle Front part Rear part Figure 4 Proceed in the same way for the rear part Once the rear rod No 19 has been fully inserted the two sliding hooks No 14 must be in contact with the rear part of the saddle seat If this is not the case it is necessary to adjust them to ensure optimum support see stage 1 To fix the two parts front and rear place the saddle and module unit vertically resting on the front part of the saddle to be able to access the central groove between the two pads Put the long part of strap No 21 through the upper rear hook No 11 and then the lower front hook No 9 Slide the end of the long part of the strap into the jaws of buckle No 22 Make sure the two parts front and rear are correctly aligned on the saddle and then pull progressively and vigorously on strap No 21 see figure 5 Front part Rear part Double reeving system to attach the saddle module Upper front pulley Upper rear pulley ie _ i0 0i Pai gaz H wA F Lower rear pulley l Locking buckle Y T Tightening force 22 2 1 Long part of strap Figure 5
4. ce with the manufacturer s instructions as from the date of purchase of the product G Group Gi Mouvly Groupe G2M Visit our website 168 ZA des Aubri res 49412 SAUMUR Cedex www groupe g2m com www mouvly com 02 41 50 50 91 contact mouvly com Purpose UU eesi device If the rider loses his or her balance putting too much stress on the abdominal support a device Device Gesi9ned 19 MAKE Mi easier Or People IO Eam lo NCS O norse is fitted to pivot automatically and release bar No 2 thus freeing the rider Its design also makes it suitable for the disabled Compatibility O The sensitivity of the device can be adjusted to suit the rider s weight The mechanism can be adjusted to obtain a This device is compatible with most standard saddles used in riding stables and pony clubs suitable level of resistance to However it is not suitable for certain models such as pommel saddles In case of doubt contact our customer service client to check for compatibility Remove the protective cloth cover clipped onto the casing Use aring spanner to loosen the locknut and then use an Allen key to adjust the locking Patent finger tighten to increase the releasing force or loosen to reduce the releasing force A patent application has been made to the INPI concerning this equipment m Then re tighten the locknut to keep the under the No 12 01875 setting Carry out the same operation on bo
5. e guides while holding down the two clips No 8 Push handle No 3 in until the two clips No 8 lock into place in their housings No 8a Before use check that the handle is securely locked in place by pulling it forward Figure 10 ting the module on the saddle Start by adjusting the rear part to suit the shape of your saddle The inner part of the saddle should have a central groove between the two pads Figure 2 Stage 1 Adjusting the rear part to suit the shape of the saddle Present the rear part inserting rod No 19 into the groove between the two pads under the saddle seat see figure 2 until the hooks No 14 and the support No 13 reach their position at the back of the saddle The rear part is held firmly in place between rod No 19 and the two sliding hooks No 14 To change their position pull on the adjusting knobs No 15 and slide them along in their guides so that the hooks come into contact with the rear part of the saddle seat to obtain a suitable setting When the hooks reach the desired position release the knobs to lock them in the corresponding hole Check that the knobs are fully inserted The adjustment has now been made 4D f at l E ae j ites BA tg en EA Y 3 Locking G Tm pan a ss a A knob p E rps Ra Siding ay A ee hooks Pils r N P ta oh Po 1 te 17 k ne F i il r a 03 15 Figure 3 Details of the rear part Etape 2
6. iding hooks Figure 8 Details of the rear part The rider is now seated in the saddle and up against the backrest Stage 6 Reposition the abdominal support by putting your hand in handle No 3 and pressing your thumb on the release knob No 20 same position as for removing it operation 3 1 figure 6 page 5 so that it is correctly aligned with the guide tubes The unit must slide easily into place If you find that it catches this is because the tubes are not correctly aligned with the rods Push the assembly fully in onto support No 1 and then release knob No 20 to lock it in place Before use check that the system is securely locked in place by pulling it upwards hard Check before use that the module is securely fixed to the saddle If not pull the strap tighter and make sure that the setting of the sliding hooks No 14 on the rear part provides a clearance free grip on the rear part of the saddle If not readjust the setting of the sliding hooks No 14 stage No 1 and retighten the strap Stage 3 Preparing the saddle to enable the rider to mount To make it easier for the rider to get astride the saddle when mounting it is advisable to remove the abdominal support from the front part and the backrest from the rear part To remove the abdominal support section from the front part put your hand in handle No 3 and press the release button No 20 with your thumb Pull the abdominal support section up
7. rectly its lower part must be in contact with the top of the saddle seat Start by adjusting the front rear backrest setting Pull locking knob No 16 with one hand and swivel backrest No 12 to bring it into position against the rider s back Release knob No 16 in the corresponding locking hole Make sure that the knob is fully inserted in its locking position Unscrew adjusting handle No 21 and adjust the shell height to bring its lower edge into contact with the top of the saddle at the desired tilt angle Lock the guide in place by tightening adjusting handle No 21 Align handle No 21 parallel to the guide by pulling and turning the handle at the same time Saddle seat 1 i i level T eE ee ed Figure 7 Before use check that the backrest is correctly locked in place by pulling it upwards and backwards the base must be resting on the saddle and the front rear locking sequence must be carried out beforehand 7
8. th mechanisms Test the sensitivity by pressing bar No 2 Check the contents of the bag It is advisable to check the setting from time to time Check the setting systematically if the It must contain mechanism trips during use A front part with a handle A rear part with a high back and a shell type back Locknut Locking finger Front part Rear part Figure Part index The module is now operational and correctly adjusted Stage amp Dismounting Before the rider dismounts repeat the procedure in stage 3 operation 3 1 removal of the abdominal support from the front part and then operation 3 2 removal of the backrest from the rear part If the rider is disabled we recommend using a mounting block or a rider lifter with the help of other persons Stage 9 Removing the module from the saddle Unsaddle the horse turn it over and press the locking lever on strap buckle No 22 Strap No 21 slips off pulleys No 9 No 10 and No 11 and releases the two parts Ancillary equipment Handle The grip handle No 3 fitted on the front part is removable It can be removed by pressing simultaneously on the two clips No 8 located on the tubes of its lower part and pulling it forwards The operation is easier if it is carried out while the front part is in place on its support r No 1 fixed to the saddle To reinstall the handle on the front part align and engage the two tubes in th
9. wards while holding button No 20 down until the section comes out of the front holder No 1 Figure 6 Details of the system used to remove the abdominal support 3 1 To remove the backrest No 12 pull out locking knob No 16 with one hand and free the backrest from shaft No 17 by pulling it upwards and rearwards with the other hand Stage 4 Now put the rider in the saddle If the rider is disabled we recommend using a mounting block or a rider lifter with the help of other persons Stage 5 Reinsert the backrest pull out locking knob No 16 with one hand and insert slot No 18 on backrest No 12 in shaft No 17 of holder No 13 The backrest must pivot freely without friction or hard spots Swivel the pad of backrest No 12 to bring it into contact with the rider s back so that the rider s back is held in a vertical position Release locking knob No 16 to let it enter the adjustment hole corresponding to that position and lock the backrest in place see figure 3 page 3 Before use check that the backrest is correctly locked in place by pulling it back and forth and up and down The different types of backrests High backrest for lumbar support high support Optional low backrest bas for lumbar support low support Shell type backrest for wraparound support To install the backrest of your choice refer to stage 5 backrest installation and adjustment To set the shell type backrest cor
Download Pdf Manuals
Related Search