User`s Manual - Parking Sensor Kits
Contents
1. not included e If necessary smooth the sharp edge of the holes with a polishing head or small round file 23s Run the sensor wires into the holes drilled Push the sensors into the holes When pushing the sensors only apply pressure at the edges not on the middle of the sensor to avoid damage to the sensor element The sensors are tapered for a snug fit g Adjust the sensors for non vertical bumper surface by using rotating the plastic sensor spacers with wedged thickness included h For front sensors run the sensor wires from the front bumper into the inside of the vehicle through the existing wiring holes or rubber grommet in the fire wall and then to the main control box in the back of the vehicle hide the wire under the door or weather trim i For rear sensors run the sensor wires from the rear bumper into the trunk or inside of the vehicle through the existing small vent or rubber grommet in the rear of the trunk or vehicle and to the main control box Note Do not cut the excess sensor wires to avoid signal loss j Attach sensor wires to the vehicle body with cable wire ties so that they will not get in the way of any moving parts and there are no loose wires hanging down k Plug all sensors into their corresponding sockets at the main control box Testing Your New Parking Sensor System Warning To avoid collision with obstacle because of the inertia of vehicle while backing up parking keep your vehicle2. speed at about 3 miles per hour and stop the vehicle immediately once you hear the continuous beeping This is because even if you have applied brake your vehicle will still go for some distance inertia before it comes to a complete stop Because the back up parking system detects obstacle by emitting ultrasonic wave and receiving reflected ultrasonic wave from obstacle the system may fail to give audible alert if an obstacle has smooth ball shaped or sloped surfaces as such surfaces may not reflect ultrasonic wave back to the sensors Drivers in these situations should pay more attention while parking their vehicles In heavy falling rain or snow the system may give alert as falling rain or snow may be detected as obstacles Keep surface of sensors clean of snow mud dirt and other debris Troubleshooting For the rear sensors back your vehicle slowly about 3 miles per hour to approximately 1 5m 4 9 feet from a flat vertical surface such as a wall Continue to back up slowly and check the performance against Chart 1 For the front sensors do the same test while parking forward slowly with braking Note have somebody watch the vehicle while you are doing the test Using the Beeper Audible Alert Problem Cause Solution No beeping when reversing or parking forward with braking Beeper not connected properly No power to the main control box Faulty beeper Check beeper connection to main control bo
3. to contact our Customer Service by visiting our Web site then click on the Contact Us link to get your Return Merchandise Authorization Number RMA Customer Service and Technical Support For customer service and technical support visit our Web site as listed below then click on the link Contact Us Spare and Replacement Parts To order spare and replacement parts for your system visit our Web site as listed below then click on the link Replacement Parts HY Technologies http parkingsensors net Copyright 2007 HY Technologies Milpitas Californias USA All Rights Reserved 6 Copyright 2007 HY Technologies http parkingsensors net HY Technologies Milpitas Californias USA All Rights Reserved a7 Made In China
4. L4 0 3L L3 0 4L L6 L7 L8 or L6 L8 0 3L L7 0 4L Main Control Box Front Sensors E F G H a OOOO Beeper Plug ES SSSEEEEE SS _ Sensor Main Control Box Plugs Power Plug gt z Sensor Center Line S Parallel to Ground El TZ Wi smog a g Ser Sensor Mounting Height 50 80cm 20 32 Q090 NG c Rear Sensors Ground Back Up Brake Gnd Light Light Fig 3 Main Control Box Beeper Sensors and Wiring Fig 4 Mounting Height and Angle of Sensor Installation and Wiring IMPORTANT a Read this manual thoroughly before proceeding to installation You can also have the system installed by a professional installer such as your local auto mechanic auto electrician car stereo store b Turn off the engine and ACC during installation c Double check that all wiring is correct before power on the system d During installation avoid flatting perforating cutting and extending the wires of sensors to reduce unnecessary signal loss 1 Installation of the Main Control Box a Find a flat and clean surface for the main control box inside the vehicle close to driver s side taillight assembly For trucks you may install it inside the driver s side taillight assembly Keep it away from areas of high heat high humidity direct water contact direct sunlight and electromagnetic devices b Place the main contro
5. User s Manual Front and Rear Parking Sensor System 4 Front and 4 Rear In Bumper Sensors with Audible Alert Beeper For Cars Mini VANs 4X4s SUVs and Small Trucks MODEL HYT F4R4 B FCC CE ISO9001 HY Technologies http parkingsensors net Copyright 2007 HY Technologies Milpitas Californias USA All Rights Reserved Front and Rear Parking Sensor System 4 Front and 4 Rear In Bumper Sensors with Audible Alert Beeper For Cars Mini VANs 4X4s SUVs and Small Trucks MODEL HYT F4R4 B Included in the Box gt 8x Sensors in bumper type with attached gt 1x Power Cable for Main Control Box cable and 2 pin mini connector Cable including three wires red yellow and Length Front Sensor 8 0m 26 2ft Rear black with a 3 pin connector on one end Sensor 2 5m 8 2ft Length 1 0m 3 3ft gt 1x Beeper with attached cable 2 5m or gt 1x Drill Bit 21mm Note if drilling 8 2ft long through metal bumpers you will need a gt 1x Main Control Box bi metal 21mm drill bit not included gt 1x Double Sided Self Adhesive Pad for gt 8x Plastic Sensor Spacers with wedged thickness for non vertical bumpers gt 1x User s Manual affixing main control box to vehicle Features gt Front and Rear Parking Sensor System to gt Beeping faster when closer to obstacle provide good coverage of both front and gt Audible alert beeper without display rear end of vehicle meaning easy to in
6. ed Faulty sensor s Faulty main control box Unplug all sensors and then plug back in one sensor at a time to find out which sensor is causing the problem Adjust angle of the sensor Refer to 4 Installation of the Sensors for details Replace the sensors s Replace the main control box Contact Technical Support for help Beeps even there is no obstacle behind or in the front Ground is detected Sensors angle is low Sensors installed too low mounting height below 0 5m Unplug all sensors and then plug back in one sensor at a time to find out which sensor is causing the problem Adjust angle of the sensor Refer to 4 Installation of the Sensors for details For more installation related questions and Frequently Asked Questions FAQs with answers and product photos visit our Web site at http parkingsensors net 5 IMPORTANT The Parking Sensor Systems sold and distributed by HY Technologies are only devices used to assist a driver while parking They should not be considered as a substitute for driver responsibility when operating a vehicle No warranty as to operational efficiency is granted We don t guarantee or assume liability for collisions or damages that take place when parking your vehicle with the use of the Parking Sensor System We will not be liable for any claims actions suit proceedings costs expenses damages or liabilities arising out of the use of this product By p
7. eded for the ultrasonic wave emitted by a sensor to reach an obstacle and for the sensor to receive the ultrasonic wave reflected from the obstacle Given the speed of the ultrasonic wave the system can then calculate and display the distance between the sensor and the obstacle To provide good coverage of both front and rear end of vehicle the system comes with 8 sensors 4 front and 4 rear sensors To have the look of factory installed system the 8 sensors are in bumper type to be installed in the front and rear bumpers by drilling holes through the bumpers Controlled by the 12V from the back up light the rear sensors are activated when the vehicle is put in reverse Controlled by both the 12V from the brake light and the OV from the back up light no 12V applied to the back up lights when parking forward the front sensors are activated when the brake is applied and parking forward It comes with a beeper audible alert which beeps faster when vehicle is getting closer to an obstacle and sounds continuously when vehicle is within 0 4m 1 3ft from an obstacle ry AA A v A Fig 1 Mounting Height and Position of 4 Rear Sensors Fig 2 Mounting Height and Position of 4 Front Sensors H 50 80cm 20 32 H 50 80cm 20 32 L1 6 15cm 2 6 L5 6 15cm 2 6 L2 L3 L4 or L2
8. l box in place temporarily without securing it to the vehicle as you may need to adjust the location of the main control box while wiring Note After completing all wiring use the double sided self adhesive pad included to secure it to the vehicle c Insert the 3 pin plug of the power cable for the main control box into its 3 pin socket labeled PWR on the front side of the main control box Fig 3 2 Wiring the Main Control Box a Locate the 12V and the negative wires from the back up light near the taillight assembly b Locate the 12V wire from the brake light near the taillight assembly If necessary remove the taillight assembly to locate them Strip 1 2 of the wires c Connect the red wire of the power cable to the 12V wire of the back up light Fig 3 d Connect the black wire of the power cable to the negative wire of the back up light e Connect the yellow wire of the power cable to the 12V wire of the brake light Wrap all connections with vinyl electrical tape 3 Installation of the Beeper a Find a place for the beeper near the middle of the vehicle on the driver side Place the beeper in place temporarily without securing it to the vehicle Note After completing all wiring secure it with the included self adhesive on the bottom of the beeper b Run the wire of the beeper to the main control box in the back of the vehicle hide the wire under the carpet or weather trim c Insert the 2 pin connect
9. or of the beeper into its 2 pin socket labeled DISP on the front side of the main control box 4 Installation of the Sensors IMPORTANT a To avoid false alert from the system detecting the ground the sensors should be mounted between 50cm to 80cm 20 to 32 above the ground and the face of the sensors need to be vertical or slightly upward angled Fig 4 b Horizontally the sensors should be equally spaced if possible or symmetric to the center of the bumper c The outer two sensors should be mounted about 15cm 5 9 from the corner of the bumper for better corner coverage Note The bumper surface for mounting the sensors should be as flat and vertical as possible Use the plastic sensor spacers with wedged thickness included if the surface of the bumpers is non vertical a Start with the front sensors and then the rear sensors Refer to Fig 1 and 2 for mounting height and position of the front and rear sensors b Work under the front and rear bumpers to check the internal structure of them before marking the positions for drilling holes If the view is blocked you may need to remove the bumpers c With chalk or marker mark the position of sensors on the bumpers Make sure that the sensors can be pushed all the way in and that you can feed the wires through d Drill the holes through the bumpers at the marks with the 21mm drill bit included Note if drilling through metal bumper you will need a bi metal 21mm drill bit
10. stall no installation of gt 4 front and 4 rear in bumper sensors to display on top of dashboard give the look of factory installed system gt Designed for cars SUVs 4x4s Mini VANs gt Rear sensors activated while reversing and and small trucks front sensors activated while parking gt 12 Month Warranty forward and braking Specifications gt FCC CE ISO9001 Approved gt Audible Alert Volume 60 db gt Operating Voltage DC 10 5 s16V gt Maximum Power Consumption 4W gt Detecting Range 0 3 1 5m 1 0 4 9ft gt Current Consumption 100 300mA gt Sensor Detection Angle 90 gt Operating Temperature Range 30 70 C gt Detection Response Time 300ms gt Size of the Beeper diameter 4 0cm 1 6 gt Audible Alert when obstacle within 0 1 thickness 1 7cm 0 7 1 5m 0 3 4 9ft gt Dimensions of the Main Control Box Width x v Depth x Height 10 0cm x 7 2cm x 2 5cm 3 9 x 2 8 x 1 0 Ultrasonic Frequency 40Khz Note The specifications are for reference only They may be changed without prior notice Tools Needed 21mm 13 16 drill bit include drill tape measure chalk or marker wire stripper vinyl electrical tape cable wire ties voltage meter screw driver set pliers Note Use a bi metal 21mm 13 16 drill bit not included if drilling through metal bumpers 1 How the System Works The Parking Sensor System determines obstacle distance by measuring the time ne
11. urchasing installing and using such a Parking Sensor System customers agree to take full responsibility of use of such System Returns and Warranty We offer 12 month product warranty This warranty excludes defects or damage due to misuse abuse or neglect Returns exchanges can be made within 15 days of your receipt of your order Note You are responsible for the shipping cost to mail the defective parts returns exchanges and items for Warranty back to us and for us to ship them to you Items for return must be in new unused re sellable condition in their original condition including the original packaging manufacturer s containers documentation warranty cards manuals and all accessories Unopened returns are subject to a 15 re stocking fee Opened returns are subject to a 25 re packing and re stocking fee Returns which are damaged or have parts missing may be subject to a greater re stocking fee or returned to customer Shipping to customer is not refundable Returns are not acceptable if the packaging is not in its original condition or the item has been used or installed International orders are not returnable If a domestic or international shipment is refused by the customer or customs and returned back to us a 15 restocking fee will apply less the shipping cost to the customer It is the customer s responsibility to make all arrangements with us for refused shipments For your return to be processed you need
12. x Check main control box connections to 12V from back up light and brake light Check main control box power connection Replace the beeper Contact Technical Support for help The beeper beeps faster as vehicle gets closer to obstacle and sounds continuously when vehicle is within 0 4m 1 3ft from the obstacle Chart 1 Obstacle Distance Alert Zones and Beeping Audible Alert System is not detecting any obstacle in front and rear Beeper not connected properly No power to the main control box Sensors not connected Faulty beeper Faulty main control box Check beeper connection Check main control box connections to 12V from back up light and brake light Check sensor connections Replace the beeper Replace the main control box Contact Technical Support for help System is not detecting any obstacle in front System has no 12V from brake light Check main control box connection to 12V from brake light System is not detecting any obstacle in rear System has no 12V from back up light Check main control box connection to 12V from back up light Alert Zones Obstacle Distance Beeping Safe Zone 2 0 1 5m Starting to beep at 1 5m Safe Zone 1 5 1 0m Beeping Fast to Faster Safe Zone 1 0 0 7m Beeping Faster to Fastest Warning Zone 0 7 0 3m Beeping Fastest Stop Zone 0 3 0 0m Beeping Continuously Beeps continuously Object within 0 40m is detect
Download Pdf Manuals
Related Search