575W moving head spot 16CH Robe type
Contents
1. mm Net Weight 33 kg DMX Protocol Function of the control channels 16 bit protocol Channel Value Function 1 0 255 Pan 2 0 255 Pan fine 16bit 3 0 255 Tilt 4 0 255 Tilt fine 16bit 5 0 250 Pan Tilt move speed from fast to slow 251 252 Pan Tilt move fast 253 255 Move fast when move the light is out 6 0 125 Switch on off the lamp 126 139 Reset 140 255 Increase speed of cooling fan 7 0 127 Color wheel1 128 190 Color flow from fast to slow 191 255 Color flow from slow to fast in the opposite direction 8 0 127 Color wheel2 128 255 White 9 0 2 No prism 3 64 3 facet prism clockwise rotate from fast to slow 65 127 3 facet prism anticlockwise rotate from slow to fast 128 255 6 kind of prism effect 10 0 79 Static gobo wheel 80 223 Gobo shake 224 255 Gobo flow from slow to fast 11 0 222 Rotating gobo wheel 223 225 Rotating gobo flow from slow to fast 12 0 2 No function 3 127 Rotating gobo rotate step by step by control 128 191 Rotating gobo rotate clockwise from fast to slow 192 255 Rotating gobo rotate anticlockwise from slow to fast 13 0 255 Iris from big to small 14 0 87 Zoom out and focus 88 170 No zoom and focus 171 255 Zoom in and focus 15 0 30 Dark 31 63 Lighten 64 95 Strobe from slow to fast 96 127 Lighten 15 128 145 Fade out from slow to fast 146 161 Fade in from fast to s2. motor is defective or its driving IC on the main PCB The yoke is not located in the default position after the reset TILT head movement error This message will appear after the reset of the fixture if the head s magneticindexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driving IC on the main PCB The head is not located in the default position after the reset This message will appear if the freguency of the mains is not standard 50 or 60 Hz Cleaning and maintenance The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 7 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the inst
3. 001 with actually set address This situation can occurr if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the MOVING HEAD575 The controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note Its necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link Remotely controllable functions Switching on and off the lamp via the Control Board 1 Switch on the MOVING HEAD575 and wait until the fixture reset has finished 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows LAMP Confirm by pressing Enter key 3 Use the Up and Down keys to select On for switching on the lamp and Off for switch off the lamp and press Enter to confirm or Mode to cancel Note It is also important to note that the discharge lamp is a cold restrike type which means that it has to be cold before re striking For this reason you have to wait 5 minutes max speed of fan must be adjusted after having switched off the lamp before you can switch it back on again If you try to switch on the lamp within 5 minutes after having switched it off the MOVING HEAD575 will store this information and automatically ignite the lamp when the 5 minutes period ha
4. 4 255 Lighten 14 0 255 Dimmer from dark to brightest Addressing The Control Board on the top side of the MOVING HEAD575 allows you to assign the DMX fixture address which is defined as the first channel from which the MOVING HEAD575 will respond to the controller If you set for example the address to channel 5 the MOVING HEAD575 will use the channel 5 to 20 for control Please be sure that you don t have any overlapping channels in order to control each MOVING HEAD575 correctly and independently from any other fixture on the DMX data link If two three or more MOVING HEAD575 are addressed similarly they will work similarly For address setting follow this procedure 1 Switch on the MOVING HEAD575 and wait until the fixture reset has finished rSt is flashing at the display 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows A001 Confirm by pressing Enter key and the letter A will flash 3 Use the Up and Down keys to select the desired address 4 Confirm by pressing Enter or Mode to cancel Controlling After having addressed all MOVING HEAD575 you may now start operating these via your lighting controller Note After switching on the MOVING HEAD575 will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will start to flash A
5. Colo EFEC rGob Grot calibration parameters Select one of them and press Enter Now you can calibrate the colour gobo and effect wheel by your controller The DMX calibration protocol is described in the table mentioned below DMX Calibration protocol After having calibrated required functions press Enter to confirm or Mode to cancel and return to the menu without reset by the ArES function and use the ArES function in order to write the calibration values to the memory EEPROM and to make a reset in order to check the new adjusted positions of the colour effect and rot gobo wheels and gobo indexing Error and information messages This message appears if you try to switch on the lamp within 5 minutes after having switched it off the lamp is too hot 6 The message will appear on the display if the lamp doesn t ignite within 28 seconds The MOVING HEAD575 will store this information and automatically ignite the lamp when the 5 minutes period has expired Caution Please note that this function is disabled if the lamp light sensor is switched off function EnSn The ignition of the lamp is seven times unsuccessful the HEAt message appeared six times before and the display shows LAEr meaning that the lamp could be damaged or even missed the fixture is overheating this can occur if the ambient temperature is 45 C or more or there could be a failure on the ignitor or ballast Please place or replace the lamp check the
6. USER MANUAL 575 SPOT Technical specifications Power supply 220 250 V AC 50 60 Hz Power consumption 900 W Fuse T 5A 250 V Lamp OSRAM HSR575 2 or PHILIPS MSR 575 2 MSD575 Optical System High luminous efficiency parabolic mirror and double condenser system Multi Step Zoom 15 18 22 All lenses are anti reflection coated Colors Color wheel 1 9 dichroic filters plus white color wheel with variable rotation speed Color wheel 2 6 dichroic filters color temperature filters 3200 K and 6000 K UV filter plus white Gobos Static gobos 9 metal gobos plus full circle Static gobo wheel cont rotation Rotating gobos 3 metal gobos 1 glass gobo and 2 multicolor dichroic gobo rotating in both directions at different speeds Gobo indexing Rotating gobo wheel cont Rotation Strobe Strobe effect with variable speed 1 10 flashes per second Dimmer Smooth dimmer from 0 100 Prism 3 facet prism rotating in both directions at different speeds Focus Motorized focus from near to far Iris Motorized iris for different beam diameters Effects 16 Prism Gobo Macros Gobo Shake function for static gobo wheel Preprogrammed pulse effects Motor 12 high quality stepping motors controlled by microprocessors Pan Tilt Pan movement range 530 Tilt movement range 280 8 16 bit movement resolution Temperatures Maximum ambient temperature 45 C Maximum housing temperature 80 C Dimensions and weight L x W x H 470x450x580
7. allation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed Disconnect from mains before starting maintenance operation DANGER TO LIFE We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches CAUTION The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the Light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Installing Replacing the lamp Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse ofsame type and rating Before replacing the fuse u
8. ambient temperature or contact your dealer if the situation was not caused by the lamp Caution Please note that this function is disabled if the lamp light sensor is switched off function EnSn This message informs you that the main PCB does not communicate correctly with the Control Board Color wheel 1 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The color wheel is not located in the default position after the reset Color wheel 2 error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The color wheel is not located in the default position after the reset Rotating gobo wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The rotating gobo wheel is not located in the default position after the reset Rotating gobo indexing error This message will appear after the reset of the fixture and if the magneticindexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The rotat
9. function hierarchy is shown below Main functions DMX 512 Address settings The letter A flashes Use the Up and down keys to select required address 001 512 and press Enter to confirm or Mode to cancel and return to the main menu Pan reverse This function allows you to invert the Pan movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Tilt reverse This function allows you to invert the Tilt movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Movement resolution By this function you can adjust the desired movement resolution 8 or 16 bit Use the Up and Down keys to select On if you wish the 16bit high resolution or Off if you wish only 8 bit resolution and press Enter to confirm or Mode to cancel and return to the main menu Note lf you adjust the 16 bit resolution the fixture will occupy 16 DMX channels if you adjust the 8 bit resolution the fixture will be operated by only 14 DMX channels Please check the DMX protocol Lamp On time This option enables you to read the total number of hours that the lamp has been powered on Press EnterJor Mode to return to the main menu In order to reset the counter to 0 you have to h
10. h not to return the Moving Head to the required position and press Enter to confirm or Mode to cancel and return to the menu Note If feedback was switched Off the PAN TILT position is changed by external force and feedbeck is switched On again the Moving Head might not to be synchronized with the DMX signal You have to make a reset in order to synchronize the Moving Head with the DMX signal Lamp off via DMX This function allows you to switch off the lamp by DMX Use the Up and Down keys to select On if you want to switch off the lamp by DMX or Off if you don t want to switch off the lamp by DMX and press Enter to confirm or Mode to cancel and return to the menu 47 Temperature Inside temperature readouts of the fixture in Celsius Inside temperatures below 80 C are not critical 80 C and more lead to the lamp being switched off Please note that the outside temperature should not exceed 45 C Fan speed operating By using this function you can choose 5 types of fan speed operating Browse through this menu by the pressing Up and Down keys the display shows step by step the following messages Auto HIGH reG Lo HI Lo OF Press Enter if you wish to select one of them or Mode to cancel and return to the menu 5 continuous controlling of the fan speed without the DMX value This mode is similar to reG but the initial level of the fan speed can t be adjusted by DMX high speed of the fans The cool
11. ically This menu allows you to turn the lamp on after switching the fixture on and switch on off the lamp light sensor Lamp On after switching the fixture on This function enables to switch on the lamp automatically after switching on the fixture Use the Up and Down keys to select On if you wish to switch on the lamp 4 automatically after switching on the fixture or Off if you wish the lamp off after switching on the fixture and press Enter to confirm or Mode to cancel and return to the menu Switch On Off the lamp light sensor Use the Up and Down keys to select On if you wish to switch the lamp light sensor On and press Enter to confirm or Mode to cancel and return to the menu The option On is for the 46 standard operation Use the Up and Down keys to select Off if you wish to switch the lamp light sensor Off and press Enter to confirm or Mode to cancel and return to the menu Important The option Off is for emergency operation only if the lamp light sensor is defective and you will wait for a delivery of the spare light sensor If the lamp light sensor was switched Off the error messages LAEr SnEr HEAt will not appear on the display only the message HEAt will appear if the lamp was turned Off and On within 5 minutes and at switching On of the lamp the electronics will still try to ignite the lamp until it shines even when the lamp is damaged or absent on this account some electronics
12. ing fans work on max speed max cooling continuous controlling of the fan speed The fan automatically raises its speed in order to control inside temperature of the lighting if the temperature inside increases about certain level the low fan speed reduces the cooling of the lighting This cycle can repeat several times until the temperature inside is on a suitable level low high speed of the fan operating The fan keeps the adjusted low speed until the temperature exceeds max inside temp of the fixture then the MH 840 automatically switches from low to high fan speed low speed switch off the lamp operating The fan keeps the adjusted low speed until the temperature exceeds max inside temp then the MH 840 automatically switches off the lamp Note In the mode HIGH and Auto the fan speed can t be adjusted by DMX Default settings Press Enter to reset all fixture personalities not the adjusting functions to the default values On the display will appear rSt meaning that the fixture makes the reset See the table of personality setting and their default positions PAN reverse TILT reverse Resolution Lamp On automatically Display permanent on Displayintensity Displayreverse Feedbackfonction Lamp Off via DMX Ventilation fan Display Default value shaded Personality Switch on off lamp light sensor 48 Adjusting the default positions of colour gobo and effect wheels By this function you can calibrate and adju
13. ing gobo is not located in the default position after the reset Static gobo wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The gobo wheel is not located in the default position after the reset Prism wheel error This message will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the ain PCB The prism wheel is not located in the default position after the reset This error message informs you that the fixture was overheating occured if the ambient temperature is 45 C or more and that the relay switched off the lamp This message will appear on the display until the temperature will be on a suitable level then the display will show the HEAt message meaning the lamp is too hot explanation see above This message appears ifthe lamp lighting sensor is failed Please contact your dealer Caution Please note that this function is disabled if the lamp light sensor is switched off function EnSn This message will appear if the fixture was shortly disconnect from the mains PAN yoke movement error This message will appear after the reset of the fixture if the yoke s magneticindexing circuit malfunction sensor failed or magnet missing or the stepping
14. low 162 191 Lighten 192 223 Strobe 224 255 Lighten 16 0 255 Dimmer from dark to brightest Function of the control channels 8 bit protocol Channel Value Function 1 0 255 Pan 2 0 255 Tilt 3 0 249 Pan Tilt move speed from fast to slow 250 252 Pan Tile move fast 253 255 Move fast when move the light is out 4 0 255 Lamp on off 5 0 127 Color wheel1 128 191 Color flow from fast to slow 192 255 Color flow from slow to fast in the opposite direction 6 0 127 Color wheel2 128 255 White 7 0 2 No prism 3 64 3 facet prism rotate clockwise from fast to slow 65 127 3 facet prism rotate anticlockwise from slow to fast 128 255 6 kind of prism effect 8 0 79 Static gobo wheel 80 223 Static gobo shake 224 255 Static gobo flow from slow to fast 9 0 222 Rotating gobo wheel 223 255 Rotating gobo flow from slow to fast 10 0 2 No function 3 127 Rotating gobo rotate step by step by control 128 191 Rotating gobo rotate clockwise from fast to slow 192 255 Rotating gobo rotate anticlockwise from slow to fast 11 0 255 Iris from big to small 12 0 87 Zoom out and focus 88 170 No zoom and focus 171 255 Zoom in and focus 13 0 30 Dark 31 63 Lighten 64 95 Strobe from slow to fast 96 127 Lighten 128 145 Fade out from slow to fast 146 161 Fade in from fast to slow 162 191 Lighten 192 223 Strobe 22
15. nplug mains lead Procedure Step 1 Unscrew the fuseholder on the rearpanel with a fitting screwdriver from the housing anticlockwise Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing and fix it Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer
16. old the Up and Downbutton and press the Enter button Power On time By this option you can read the total number of hours that the MOVING HEAD575 has been powered on Press Enter or Mode to return to the main menu Switch on off the lamp Use the Up and Down keys to select On if you wish the switch on the lamp or Off if you wish switch off the lamp and press Enter to confirm or Mode to cancel and return to the main menu Demo sequences This function allows you to run a special demo test sequences without an external controller which will show you some possibilities of using MOVING HEAD575 Press Up and Down keys to select the Mod1 or Mod2 sequences The Mod1 is suitable for projections on the wall ceilling or ground without any headmovement the Mod2 uses all MOVING HEAD575 functions and therefore is good for a complete introduction of the fixture 45 Reset Function Press Enter key to run reset This option enables the MOVING HEAD575 to index all effects functions and return to their standard positions SPEC Special functions Use the Up and Down keys to browse through the special functions and select the one by pressing Enter Manual control of effects This function allows you to control manually the channel functions of the fixture Use the Up and Down keys to select desired function and press Enter to adjust the effect or Mode to cancel and return to the menu Lamp On automat
17. parts could be damaged DMX values Readout DMX values of each chamnel received by the fixture Use the Up and Down keys to select desired channel and press Enter to read its value coming to the fixture or Mode to cancel and return to the menu Display adjusting This function allows you to adjust the display settings Display intensity With this function you can adjust the display intensity from 20 to 100 Use the Up and Down keys to select the level of the display intensity and press Enter to confirm or Mode to cancel and return to the menu Display reverse With this function you can rotate the display by 180 Use the Up and Down keys to select normal display or display turned by 180 and press Enter to confirm or Mode to cancel and return to the menu Display On This function allows you to keep the display on or to turn off automatically 2 minutes after last pressing any key on the control board Use the Up and Down keys to select On if you wish to keep the display on or Off if you wish to turn off automatically 2 minutes after last pressing any key on the Control Board and press Enter to confirm or Mode to cancel and return to the menu PAN TILT Feedback This function allows to return the Mowing Head to the required position after changing the position by external force e g by stroke Use the Up and Down keys to select On if you wish to enable this function or Off if you wis
18. s expired The message HEAt will appear on the control board display at the back side of the MOVING HEAD575 If the ignition of the lamp is seven times unsuccessful on the display will appear LA Er meaning that the lamp could be damaged or even missed or there could be a failure on the ignitor or ballast Fan The MOVING HEAD575 is cooled by three axial fans one each in the projector head and one in the base The speed of the fan and of course the noise can be continuously reduced if very quiet performance is required By the Control Board using the FAnS function you can choose 5 types of low fan speed operating Please refer to the instructions under SPEC Special functions Control Board The Control Board situated on the top side of the MOVING HEAD575 offers several features You can simply set the lighting address read the number of lamp or unit hours switch on and off the lamp run demonstration seguences make a reset and also use special functions for manual control and service purposes The main menu is accessed by pressing the Mode key press this one so many times until the display shows message A001 with actually stored address Browse through the menu by the pressing Up and Down keys the display shows step by step these messages A001 rPAn rTilt 16br Lati Poti LAMP dEMo rESE SPEC Press Enter if you wish to select one of them The functions provided are described inthe following sections and the
19. st the colour gobo and effect wheels to their standard right positions Use the Up and Down keys to browse through the adjusting menu the display shows step by step these messages PAn Tilt SPEd Col1 Col2 PriS SGob rGob Grot IriS Foc Stro dimr FCAL by which you can adjust the fixture to the required desired position 0 255 before the function calibration Then when the positioning is finished use the last FCAL function Fixture calibration 1 Calibration via the control board Press Enter and the Up and Down keys in order to display the following messages Col1 Col2 PriS SGob rGob Grot for very smooth function calibration Select one of them press Enter and use the Up and Down keys in order to adjust their right value from O to 255 Then press Enter to confirm or Mode to cancel and return to the menu This can be repeated for each calibration parameter if it is required When the calibration is finished it is necessary to use the ArES function in order to write the calibration values to the memory EEPROM and to make a reset in order to check the newly adjusted positions of the colour gobo and effect wheels When the reset of the fixture is finished the display will show the FCAL message Press Enter to repeat the calibration or Mode to return to the AdJ menu 2 Calibration via the external controller Press Enter and the Up and Down keys in order to display the following messages
Download Pdf Manuals
Related Search