Home

Power Stone Manual v.1 - Multi

1. Passive On or Passive Off and you can also access Manual Operating mode from a remote location 20 2 Controlling Power To Equipment That Does Not Require A Phone Line The Power Stone is not a one dimensional product It can control power to virtually any equipment that requires up to 15 Amps at 120 Volts You can use The Power Stone to control power to a lamp stereo equipment a crock pot any device you can think of that meets the load specifications of The Power Stone a The Power Stone is plugged into a 120 Volt wall outlet b The Power Stone is connected to the telephone line via the supplied line cord On end is plugged into the tdephone wall jack and the other end is plugged into the port labeled LINE The device you wish to control power to is connected to the 120 Volt receptacle on the face of The Power Stone d The equipment lamp stereo equipment etc does not require connection the phone line 120 VAC WALL OUTLET INCOMING LINE TELEPHONE WALL JACK HOME LAMP STEREO EQUIP ETC Heplful Tips In this installation the Power Call Automatic Operating mode will not perform as touted Since there is no auto answer equipment fax modem devices in this application Power On Call as an operating mode should be avoided All other operating modes are applicable and will function in this installation such as Reboot Toggle P
2. RELAX This is NOT rocket science About This Manual Weare serious about making the finest products on the market And we are serious about the information you need to make the product function correctly but we can t get real serious about writing product manuals There are enough bad product manuals out there to sink an aircraft carrier You ve probably seen them the ones that take a degree in Electrical Engineering to figure out or they are written in every language except English or they are just plain boring Our humor or wit or lack of either in the rhetoric of this manual is not put here to lessen any aspect of the product except maybe the painful task of getting through some very dry material Thanks Something You Should Know Now That You Have Purchased Our Product You are the most important person in the world and we at Multi Link want to THANK YOU for your business We can t say it enough At one time in America business was conducted face to face where a word and a handshake were good enough While we seldom get the opportunity to personally meet and thank the people who buy our products we realize your purchase of The Power Stone is a vote of confidence and trust in our product and our company We will not betray this confidence or trust that is our word and handshake to you You are the backbone of our business The ultimate goal we as a company have targeted is your satisfaction We want you as a cus
3. AUDI ANSWER NO OF RINGS FEATURE OVERRIDE BUTTON OVERRIDE PROGRAMMABLE gt SECURITY FEATURE POWER STATUS REAO ONLY NON PRDGAMMABLE POWER FAILURE STATUS READ ONLY NON PROGAMMABLE 0 PASSIVE OFF No power is supplied to equipment regardless of ring 1 PASSIVE ON Poweris supplied to equipment regardless of of rings POWER ON CALL Power supplied when inbound call rings are detected Power turned off at the end of a call within 2 minutes REBOOT When ring is detected power is stopped tor 15 seconds TOGGLE Power is switched on or off with each subsequent call 2 OR LESS RINGS When two or less rings are detected The Power Stone will perform operating modes 2 thru 4 3 rings or more will not react 3 3 OR MORE RINGS When 3 or more rings are detected The Power Stone will perform operating modes 2 thru 4 2 or less rings will not react Single Ring Cadence Sensitive to only a single ring cadence Double Ring Cadence Sensitive to double ring transmitted by phone Co Triple Ring Cadence Sensitive to triple ring transmitted by phone Co 0 AUDIO ANSWER 15 Rings Tha Power Stone answers at 15 rings and transmits power status tones same as Reg 07 Will hold the line for 10 sec 1 AUDIO ANSWER 3 Rings The Power Stone answers at three rings and transmits power status tones same as Reg 07 Will hold the line for 10 sec 0 Normal Op
4. 5 2 Helpful Tips Yes we know what you are thinking But there is a real world use for these two operating modes The reason for providing you with these two passive modes is this SECURITY If your PC modem is connected to the phone line through The Power Stone outside access by callers isdenied when The Power Stone is in the Passive Off operating mode The PC modem won t answer the line because the PC isn t receiving power Only you can call in and turn your PC on Just call and when a voice telephone device goes off hook like your answering machine or The 10 Power Stone goes off hook afier 15 rings enter your security access code Now you can change Passive Off mode to Passive On by dialing 011 Enter 80 to write your change to menory and hang up Of course in between entering your SAC changing operating modes and dialing 80 to prograrn exit The Power Stone will be prompting you with Audible Readback response beeps To get a better understanding how to perform these functions refer to example number four in the section titled Down N Dirty Application Info For The Terminally Impatient What about the Passive On mode You may require that connected equipment be supplied power until you call in and direct The Power Stone to shut power down Connected equipment in this example and application can be a bulletin board PC LAN or for you gadget heads on the cutting edge home
5. factory preset at 8 8 can be customized by the addition of 2 characters at the end of the code string The digits 0 through 9 Star and pound can be programmed as additional characters to prevent callers from turning on and hacking into your voice data equipment or inadvertently changing the status of power supplied to equipment Register 06 controls this feature Override Button Override Sound weird Wall it s not This featureis beneficial to the terminally forgetful the face of The Power Stone is an OVERRIDE button which when pushed overrides all operating modes and supplies an uninterruptable flow of power to your connected equipment let s say a PC you need to do some work For some unknown reason you fly off to parts unknown the next day forgetting to take The Power Stone out of override mode You callin to get messages off your answering machine and discover your PC modem is powered on and your intemal modem is screaming at everyone who is calling Just get into Manual Operating mode access the OVERRIDE Button Override register and program The Power Stone back to normal operation In the event of a power outage both override s the button and the register revert to factory preset which is Normal Operation or override off Register 05 controls this feature 11 Operating Modes operating modes passive and automatic are contained in Register 0 1 See sections titl
6. Beeps Symbols 2 Long Beeps Addtl Short Bips COPYRIGHT 1995 MULTI LINK INC NICHOLASVILLE KY 23 12 FCC Regulation This equipment complies with Part 68 of the FCC rules On the bottom of this equipment is a label that contains among other information the FCC Registration Number and Ringer Equivalence Number REN for this equipment You must upon request provide this information to your telephone company The REN is used to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If your telephone equipment causes harm to the tdephone network the tdeohone company may discontinue your service temporarily If possible they will notify you in advance But if advance notice isn t practical you will be notified as soon as possible You will be informed of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance to give you an opportun
7. Feature 42 Distinctive Ring Cadence Detection Feature 43 Automatic Operating Modes Passive a ER 10 5 1 Passive Operating M odes 5 2 Helpful Tips Programmable Features W 11 Standard Nonprogrammable Features 12 7 1 Read Only Registers 7 2 Audible Readback Of Programming 7 3 Manual Override Button 7 4 Telephone OverrideCommands 7 5 Status Power LED 7 6 Circuit RESET Button EJ The Programming And Quick Reference 14 Manual Operation Programming Of The Power Stone 15 9 1 The How To Of Programming 9 2 Overview Of Programming 9 3 Audible Readback Of Programming Installation Overview Helpful Tips icin 20 Remote Programming Feedback 22 Registration i E OA 24 IB Warranty Service Informations 25 Technical 26 Copyright 1995 All Rights Reserved Multi Link Inc Nicholasville Kentucky 40356 Safety Instructions When using your telephone electrical power equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read and understand all instructions 2 Follow all warn
8. The Power Stone to supply a constant uninterrupted supply of electricity to your connected equipment The Power Status LED will glow brightly with no flashing All inbound calls will be ignored by The Power Stone Pressing the OVERRIDE button again will return The Power Stone to its previous programmed operating mode In the event of a power outage both override s the button and Register 05 revert to factory preset which is Normal Operation or OVERRIDE off 12 7 4 Telephone OVERRIDE Command If The Power Stone is plugged into a power strip wall outlet and you can t get to it to press the OVERRIDE button there is a touchtone command that will perform the same function as pressing the OVERRIDE button To do this you must have a touchtone phone connected to the DEVICE port Press the star symbol on your touchtone phone and The Power Stone will go into OVERRIDE get The Power Stone out of OVERRIDE and back to its previous operating mode press the Star character twice Telephone OVERRIDE Command will only work when the Power Stone is not in Manual Operating mode Note If you arein the programming mode you cannot override by dialing In the event of a power outage both overide s the button and Register 05 revert to factory preset which is Normal Operation or OVERRIDE off 7 5 Status Power LED The Status Power LED signals the status of power supplied to your equi
9. appropriate number of inbound rings will have to be detected before The Power Stone will perform automatically 4 3 Automatic Operating Modes The Power Stone can be programmed to automaticallv_ control electrical power to your chosen equipment three different ways Of course your choice of operating mode is dependent on your application but for now we ll keep it clean and talk about the different ways power can be manipulated automatically Automatic operating modes along with passive operating modes are selectable and reside in Register 01 Power OnCall This one s pretty cool for fax modem and fax machine users who don t want to leave Office equipment powered up 24 hours a day In this operating mode the Power Stone when tripped by the appropriate number of rings of course will supply electrical power to equipment plugged into its 120 Volt receptacle for the duration of that phone call When ether party hangs up the call is over The Power Stone will power down that equipment within two minutes Any incoming call detected during the two minute interval after the previous caller has hung up will continue the power up process for the duration of that call plus an additional two minutes Reboot You may want to temporarily interrupt power to selected equipment such asa locked up PC or modem In Automatic Reboot mode electrical power is constantly supplied to equipment plugged into The Power S
10. lighting stereo equipment even a crock pot that is cooking your 3 Ib rump roast Get creative Again refer to example number four in the section titled Down N Dirty Application Info For The Terminally Impatient 6 Programmable Features Audio Answer Number of Rings The Power Stone has a feature that allows it to automatically answer the phone line after a number of rings and audibly readback the status of power supplied to your equipment The factory preset number of rings for this feature is 15 The other selectable option is 3 rings After answering and transmitting the status of power supplied to connected equipment to a caller The Power Stone will remain off hook for 10 seconds before hanging up the call This allows you to call and manually control The Power Stone from remote location without having an auto answer device like an answering machine at The Power Stone s location Remember that to get into Manual Operating mode something at The Power Stone s location must go off hook and answer the line If you don t have an answering machine just wait 15 rings If you re a hurry program itto answer after 3 rings Register 04 controls this feature Customized Security Code Feature To getinto Manual Operating mode and control power from a remote location you must transmit your Security Access Code through the phone line via a touchtone phone to The Power Stone The standard security code
11. 1 Recommended Operating odes Use Passive Off mode if you want equipment to be powered off until you call in to The Power Stone and manually turn it on Use Passive On mode if you want equipment powered on until you call in to The Power Stone and manually turn it off Recommended Programming A Rings Trip feature regardless of setting does not function when either passive mode is programmed so don t worry about programming Rings To Trip 6 Before you can access The Power Stone s Manual Operating mode with your security code something must first answer the phone line at the site This can be accomplished with an answering machine connected to the phone line If you don t own an answering machine you can call The Power Stone let it ring 15 times and it will automatically answer giving you an audible power status beep see Audio Answer Number of Rings feature page 11 At that time you have 10 seconds to transmit your touchtone security code If you don t want to wait 15 rings program register 04 Audio Answer No of Rings to 3 REMEMBER rings Now The Power Stone will automatically answer in 3 VSE TOUCH rings give a status beep and you have 10 seconds to enter TONE PHONE your touchtone security code on the key pad To Enter Manual Operating Mode And Turn Power ON To Your Equipment 1 The Power Stone or answering machine a
12. BOL AUDIBLE TONES BEEP BEEP BOOOOOOP 1 BIP There is a manual control command that 2 BIP BIP allows The Power Stone to audibly readback via the phone the value of any register This feature is handy when you re calling long distance to your home BEEP BIP and you have forgotten what you have just BEEP BIP BIP programmed and want a quick readback BEEP BIP BIP BIP when checking to see if The Power Stone BEEP BIP BIP BIP BIP is properly programmed before leaving BEEP BEEP your home or office There are two types of tones that The Power Stone will transmit BEEP BEEP BIP BIP through your receiver on the audible read back A clipped high pitched bip which has a numerical value of one A long low pitched beep which has the numerical value of five The chart to the right describes the audible tones which coincide with each number or symbol in a register BEEP 5 6 x SHE 18 Executing Audible Read Back With The Power Stone First you must enter the M anual Operating mode by dialing 8 8 or your customized code Then press and the register number you wish to read back An Exarnple First you press 8 8 on your touchtone phone to enter the M anual Operating mode The Power Stone responds with a PROCEED tone You press 01 telling The Power Stone to audibly read back the valuein R
13. MANUAL OPERATION PROGRAMING OF THE POWER STONE This is the greatest asset of The Power Stone You can call to your home or Office from remoce location and control the power to your selected equipment or change the automatic operation at the site of The Power Stone just by pressing characters on your telephone key pad You can also check the status of each programmable setting and receive information about power status to a device Before You Can Access The Power Stone If you wish to access The Power Stone s Manual Control mode from a remote location OR right on site some basic requirements need to be satisfied For On Site Access A TOUCHTONE telephone must be connected to the DEVICE port of The Power Stone You may if you have a modem plugged into the DEVICE port connect your telephone to the Phone port on the back of the modem If your modem does not have a Phone port on the back pane and you need to have a phone and modem connected to the Power Stone s DEVICE port use a telephone splitter adapter We recommend a splitter adapter similar or equal to the AT amp T adapter part no 267A2 because of the over under splitter configuration This type of splitter adapter when plugged into The Power Stone s DEVICE port will not interfere with the LINE port directly beside it Access When Calling From A Remote location Ifyou are calling
14. Readback Enter then Register No of any register press Star followed by the Register 01 Operating Modes appropriate Register No The Power Stone 0 Passive OFF Beep Beep Low will then readback the programmed setting 1 Passive ON Bip with audible Beeps and or Bips 2 Power On Call Bip Bip 3 Reboot Bip Bip Bip 4 Toggle Bip Bip Bip Bip To the right of each feature setting in a ae Bip Bip Register is the corresponding audible Beep Bip readback r that If you pas Pinga Pip Pip Bip readback Register 01 and the programmed Register 03 Distinctive Ring Cadence setting is Power On Call The Power 1 Single Ring Bip Stone will audibly transmit Bip Bip 2 Double Ring Bip Bip through the phone line ro you 3 Triple Ring Bip Bip Bip Register 04 Audio Answer_ of Rings 0 Audio Answer 15 Rings Beep Beep Low 1 Audio Answer 3 Rings Register 05 Override gt 0 Normal Operation Beep Beep Low 1 Override Mode Bip The arrow beside a program setting in each Register denotes the factory preset In other words this is how The Power Stone is programmed out of the box or if you hit 60 as an input command p gt Denotes Factory Preset OVER 22 Response Signals are different than the readback Beeps Bips of a feature setting During readback and program ming The Power Stone transmits these signals as a form of feedback aft
15. To Trip feature Here s how Rings To Trip works When a call rings into the location of The Power Stone your selected automatic operation will be activated or tripped when The Power Stone detects either 2 or less rings or or more For more detailed explanation about Rings To Trip options see page 8 Passive Operation The Power Stonealso has two passive operating modes Passive On and Passive Off that totally ignore the rings of an inbound call while providing either no power Passive Off or constant power Passive On to your equipment Either passive mode is useful when you do not want an inbound call to change the status of the power to your equipment How Do You Hook It Up This part is real simple and straight forward in good 01 plain English Refer to page 20 Installation Overview Hdpful Tips section for pictures It contains two installation schematics that should cover virtually any application that you have in mind The installation part is a no brainer What really makes The Power Stone work is your choice of operating mode Passive or Automatic the sdected number of rings to trip an Automatic operating mode your understanding of how to access Manual Operating mode from a remote location and the audible readback feature Plugging Into 120 Volt Power On the backside of The Power Stone there are three metallic blades which look like the 120 Volt electrical blades fou
16. age fire flood or damage resulting from repairs or alterations performed other than by authorized service stations This warranty gives you specific legal rights and you may also have other rights which vary from state to state Service Information Your machine has been registered with the Federal Communications Commission and under this program in the event of equipment malitinction all repairs will be performed by Multi Link Inc ora warranty repair center that we have authorized The owner is restricted fmm performing any maintenance operation other than those specified within this instruction manual If you require service please contact your dealer or Multi Link Inc at In Canada Unit A1 6120 2nd Street S E Calgary AB 2 2L8 1 800 661 8371 In the U S 225 Industry Parkway Nicholasville Kentucky 40356 1 800 535 4651 DON T FORGET TO FILL OUT AND MAIL YOUR WARRANTY CARD 25 14 Technical Specifications Input Power Requirement 120 Volts AC 60 Hz Maximum Current Output 15 Amps General Purpose Maximum Power Output 600 Watts Incandescent 1800 Watts General Purpose Ringer Equivalence Number 1 1 B For Indoor Use Only No Seviceable Parts Inside UL Listed 9NO6 Appliance Control United States and Canada 26 The Power Stone contains patented and otherwise proprietary circuits and software algorithms This owner s manual describes the operation and function of some of these circuits and algorithm
17. as the PC The problem is not with The Power i Stone The problem is with the fact that the PC is powered up all the time and the modem would probably or grab the line before your answering machine does We Beier refer you to the previous application to overcome this problem 5 3 If You Want To Power PC Automaticaliy Using the Distinctive Ring Service Installation Refer to Installation Number 1 on page 20 of the Installation Overview Recommended Operating Mode Power On Call Factory Prese Additional Requirement Subscribe to the Distinctive Ring service and receive an additional phone number from your local tdephone company See page 9 for Distinctive Ring service info Recommended Programming A Program Distinctive Ring Cadence Detection feature to detect the inbound call ring pattern of your DR phone number The additional phone number A should ring two ring or double burst pattern as 2 WS program Register 03 with the number 2 for wo N double ring detection al 4 give your PC the ability to power up automatically and have it answer with one call set Rings To Trip at 3 rings or more Factory Preset The caller should continue to ring the PC until it answers C If you want to power up the PC but need boot up time before the moden will answer set Rings To Trip at 2 ring
18. assive On or Passive Off and you can also access Manual Operating mode from a remote location Remember that to access Manual Operating mode a telephony device answering machine phone will need to go off hook before you can transmit your security code over the phone line from a remote location If you do not have a device that will go off hook automatically you can reprogram The Power Stone s Audio Answer feature to answer at 3 rings or B simply ring The Power Stone 15 times factory preset 21 11 Remote Programming Readback How To Read Use Your Remote Programming Readback Card A Remote Programming Readback Card has been included with The Power Stone to help guide you from a remote location through access programming and readback of features power status Here are some views of the card with less condensed explanations of what you are seeing Relax It s fairly easy to understand Again we urge you to stick this card in your wallet purse or brief case Maybe you can keep it next to your long distance calling card just a thought Your Security Access Code when dialled puts The Power Stone in Manual Operating REMOTE PROGRAMMING READBACK CARO Mode You can customize the SAC with two additional charactets Register 06 Remember to record your customized code S i ONE on this card My Secutity Access Code is 8 8 If you wish to get a readback on the setting Audible
19. ct Il To reduce the risk of electric shock do not disassemble this product but take it to a qualified serviceperson when some service or repair work is required Opening or removing covers may expose you to dangerous voltages or other risks Incorrect reassembly can cause electric shock when the appliance is subsequently used 12 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When a power supply cord plug or phone line cord connected to the product is damaged or frayed B If liquid has been spilled into the product but it is thoroughly dried out C If the product has been exposed to rain or water but it is thoroughly dried out D If the product does not operate normally by following the operating instructions adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result indamage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged F If the product exhibits a distinct change in performance 13 Avoid using a telephone other than a cordless type during an electrical storm There may be aremote risk of electric shock from lightning 14 Do not use the telephone to report a gas leak in the vicinity of the leak 15 Do not touch or attempt to unplug this product
20. ct the previous attempt by entering new numbers Summary of the types of tunes you will hear PROCEED Three high pitched tones in rapid succession tell you The Power Stone is ready to program a register or receive more commands in the form of touchtones Bip Bip Bip OK Or Okay for you purists One high pitched tone immediately followed by a mid pitched tone means that the numbers you have entered are acceptable and within range for the register number and value 16 ERROR A single low pitched tone indicates that the register number feature value or program commands we talk about those next that you have entered are invalid After receiving an ERROR tone you should wait two seconds before proceeding Common errors made when programming are Entering an incomplete register number let s say it s Operating Modes and you enter only part of the number The register number for Operating Modes is 01 If you enter I The Stick will give you an ERROR tone Entering a feature value that is outside of the program range As an example we will use Operating Modes again You are only allowed to sdect and program modes 1 2 3 or 4 If you enter the number 5 there is no fifth operating mode after entering the correct register number of 01 The Power Stone will give you an ERROR tone Waiting more than two seconds bet
21. degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the tdecommunications company cause to request the user to disconnect the equipment 24 Users should ensure for their own protection that the electrical ground connections of the power utility tdephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections thernselves but should contact the appropriate electric inspection authority dectridan as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to tdephone loop which is used by the device to prevent overloading The termination a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 Notice This product has been tested and meets the Class B limits for radio noise emissions set out by the Radio Interference Regulation of the Canadian Department of Communications 13 Limited Warranty We warrant that if this product manufactured by Multi Link Inc and purchased by you proves to be defective in material
22. ed Automatic Operation and Passive Operation for feature explanation Rings To Trip Automatic Operation Register 02 controls this feature setting Refer to Rings To Trip Feature in section titled Automatic Operation Distinctive Ring Cadence Detection Register 03 controls the setting for this programmable feature For full feature explanation refer to Distinctive Ring Cadence Detection in section titled Automatic Operation 7 Standard Nonprogrammable Features 7 1 The Power Stone contains two read only programming registers The Power Supplied Status Register Register 07 will readback the current status of power supplied to connected equipment Two low beeps tell you The Power Stone is not supplying power to your equipment One beep tells you power is supplied to the equipment The Power Failure Status Register Register 08 will tell you if a power failure has occurred since the last reading of this register Two low beeps tell you power has not been interrupted to The Power Stone since your last inquiry One beep indicates that a power outage has occurred since your last inquiry 7 2 Audible Readback Of All Programming Upon accessing The Power Stone s Manual Operating mode you can direct The Power Stone to readback any programming and feature settings See page 15 for a more in depth explanation 7 3 Manual OVERRIDE Button Pressing this button will direct
23. egister 1 The Power Stone transmits 2 Bips signifying the value 2 Power On Call After a short pause The Power Stone will transmit an OK tone followed by a PROCEED tone At that time you may either read back or program any register For Registers Containing More Than A Single Value Register 6 can contain and does readback more than a single value a short example of what a readback would sound like where more than 2 digits or symbols are programmed the register You first enter M anual Operating mode 8 8 or your customized code Press 06 to read back Register 6 The Power Stone transmits Beep Beep pause Beep Beep Because the register is not programmed with a custom Security Access Code it contains the numerical value zero zero This translates into two sets of two low pitched beeps The Power Stone immediately transmits the OK and Proceed tones Helpful Tips If You re Having Trouble After entering 8 8 to get into Manual Operating mode you have 30 seconds to enter a complete readback command After 30 seconds if no readback information is entered The Power Stone will transmit an Okay tone Bee Bip and exit programming mode The Power Stone acts as if you have dialed 90 Note You will receive an Error tone when entering star and an incorrect or partial register number on audible read back Never fear t
24. er you have inputted a command Check page 16 for full blown descriptions After programming The Power Stone Input Commands allow you to record your programmed settings to memory or erase them and start over Input Commands can be used at any time during programming This part of the card describes the audible readback Beeps Bips that correspond to numerals 1 thru 9 0 and 0 equals 10 equals 11 and equals 12 So if a Bip means 1 and a Beep means 5 a Beep Bip 5 1 equals six A Beep 5 5 equals ten or 0 Get it No See the table on page 18 for the real deal Register 06 Customized Securitv Code Beep Beep Beep Beep Low p gt 00 No Code Code Your 6 Register 07 Power Supplied Status 0 No Power Supplied Beep Beep Low 1 Power Supplied Bip THIS REGISTER IS READ ONLY Register 06 Power Failure Status 0 No Failure Last Read Beep Beep Low 1 Failure Last Read Bip THIS REGISTER IS READ ONLY Input Commands 60 Set All Registers to Factory Preset 80 Write Programs to Memory and Exit 90 Exit Manual Op Mode w o Saving ignal Beep Bip Information Accepted Bee Bip Bee Bip Info Accepted Exit Mode Low Beep Error Bad Input Command Numerals 1 4 Coinciding of Short Bips Numeral 5 1 Long Beep Numerals 6 g 1 Long Beep Addtl Short Bips Numeral 0 2 Long
25. eration The Power Stone will operate in the programmed operating mode when the proper of rings are detected 1Dverride Operating modes are overridden and power is supplied to equipment constantly regardless of Register 2 setting 00 No Security Access Code To enter manual control all you dial is 88 __ 2 To add 2 characters to the end of the securfty access code strfng 0 Audible 2 low Beeps tells you no power is supplied to your equipment 1 Audible 1 Bip tells you power is supplied to your equipment 0 Audible 2 low tells you there has been power failure since the last reading of this register 1 Audible 1 Bip tells you there has been a power failure since the last reading of the register DENOTES FACTDRY PRESETS Pro romining Commands l 88 The factory preset code for access to Manual Mode and programming Command 60 Set registers 01 02 03 04 05 and 06 to factory presets Command 80 Save current contents of registers to memory and exit manual control Command 90 Exit manual control without saving changes to register All registers will be restored __ with the values last saved in NOTE Registers 07 and 08 are and when accessed will audibly read out status of power and immediate history of power failure at the site Register 05 Override always reverts to the preset when a power outage occurs 14 Manual Operation Programing
26. from a remote location you must be placing the call from a touchtone phone and the call you place to the location of The Power Stone must be answered by either A an auto answer device like an answering machine modem fax machine or a person or C if A or is not available you can simply let the phone line ring 15 times and The Power Stone will go off hook automatically The Power Stone can be programmed to answer the line after 3 rings see page 11 Audio Answer feature Operations Note The Power Stone upon answering the phone line option C will transmit two different types of audible tones signalling the status of power to your selected equipment AND HOLD THE LINE FOR 10 SECONDS See the Programmable Features Section Audio Answer Feature Two low beeps indicate The Power Stone is receiving power from the wall socket but is not sending power to your selected equipment One bip signals that electrical power is being supplied to equipment plugged into The Power Stone If The Power Stone does not answer and transmit tones after the 15th ring you have a power outage at The Power Stone s location 9 1 The HOW TO Of Programming The Power Stone Now that everything is hooked up and in place the fun begins You should read through this section once or twice to familiarite yourself with the process You may also want to refer back to the Programming and Quick Referente Guide to pencil
27. from the wall outlet if A liquid has been spilled into the product and it is wet or suspected to be wet B the product has been exposed to rain or water and it is wet or suspected to be wet INSTALLATION INSTRUCTIONS 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specially designed for wet locations 3 Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying telephone lines How The Power Stone Works Slick Hi Tech Marketing Statement The Power Stone is a call activated power control call processor that can perform a number of functions relating to the supply of 120 Volt power to your selected equipment This feature rich power controller enables you to power up power down or interrupt power to your equipment up to 15 Amps at 120 Volts through a single phone line either with its automatic operation capability or by manually inputting commands through the phone line in the form of touchtones from a telephone Hopefully Plain and Simple If the previous paragraph said too much here s the deal in layperson terms The Power Stone can work for you three ways automatically passively or manually and with all the available programming features it will satisfy your power control requirements for just about any ap
28. g mode This is done by pressing 01 for Operating odes Register 1 and 07 for Power Status Register 7 5 You press 80 on your touchtone key pad The Power Stone bee bips twice You hang up Your equipment is now powered off Helpful Tips Included with The Power Stone is a Remote Programming Readback Card which is a handy reference when you want to control The Power Stone from a remote location It eliminates the need to memorize register and feature numbers gives you the command for Audible Readback of each register feature and explains the meaning and numerical value of The Power Stone s readback beeps See page 22 for more info Please put it in your purse or wallet and don t leave home without it 7 5 If You Want Call In From Remote location Readback Programming And Power Status Installation Either Installation 1 or 2 is suitable for this application Refer to Install Overview page 20 21 To Enter Manual Operating Mode And Readback Programming And Power Status To Your Equipment 1 The Power Stone or answering machine answers your inbound call 2 You enter 8 8 on the touchtone phone The Power Stone bips 3 times Proceed 3 At that time you enter with the appropriate register number 4 There is a short pause followed by the register readback in the form of bips and or beeps 5 There is a short pause after the readbac
29. he basic grasp of how The Power Stone operates If not please browse through this section again If you know or think you have a good idea about your application and how The Power Stone needs to be programmed go for it If you have no idea or just want to get some quick input please read the next section appropriately titled Down N Dirty Application Info wk Kas FOR THE TERMINALY IMPATIENT In The Home or Home Office The Power Stone can be used to control power to many different types of electronic devices normally found in the home or office Again home and office applications are dependent on what you want to control power to and how you want to do it Some of the more popular applications with recommended programming scenarios are listed in this section 1 If You Want To Power Up A PC Modem or Fax Machine Automatically Installation Refer to Installation Number 1 on page 20 of the Installation Overview Recommended Operating Mode Power On Call Factory Preset Recommended Programming A To power up the PC and have it answer with one call set The Power Stone s Rings To Trip to 3 rings or more The caller should continue to ring the PC modem until it answers Factory Preset m NEED B If you want to power up the PC but need boot up POWER time before an internal modem will answer set Rings i i NOWIU To Trip at 2 rings or le
30. in selected programming values for each feature you wish to control The first thing you should do is place a local call to your best buddy Ask him or her to lay their phone receiver down for a moment but don t hang it up This will keep you from incurring any long distance phone charges or freaking out the local phone company After placing a call to your friend wait at least five seconds before proceeding To get into Manual Opemting Mode DIAL 8 8 on your klephone key pad _ The STATUS light will begin blinking rapidly Immediately listen for three high pitched bips in your handset Three bip tones indicate that you have entered the programming mode and may PROCEED At this time you can enter a register number 01 to 06 followed by the value you want to program into the register If the proper register number and programming value s are entered The Power Stone will answer with a high pitched tone immediately followed by a mid pitched tone It kind of sounds like bee bip This means OK If the numbers you enter are invalid either for the register number or program value The Power Stone will respond with a low pitched ERROR tone This tone might remind you of thesound you hear when you blow it on your favorite video game In either case three bips will immediately follow telling you to PROCEED At this time you may ether access and program anew register or corre
31. ings and instructions marked on the product 3 Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp doth for deaning Let dry thoroughly before plugging device back into 120 Volt outlet 4 Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Do not use this product outdoors 5 Do not place this product onan unstable cart stand or table The product may fall causing serious damages to the product 6 This product should never be placed near or over a radiator or heat register This product should not be placed ina built in installation unless proper ventilation is provided 7 This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your dealer or local power company 8 Do not allow anything to rest on the power cord to phone lines connected to it Do not locate this product where the cord will be abused by persons walking on it 9 Do not overload wall outlets and extension cords as this can result in the risk of fire or electricn shock 10 Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the produ
32. ity to maintain uninterrupted telephone service If you experience trouble with this telephone equipment please contact your dealer or Multi Link Inc for information on obtaining service or repairs The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning This equipment may not be used coin service provided by the company and is not intended for use with party line service This equipment is intended for use only on loop start service and will not operate a ground start central Office line DOC Registration The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets certain tdecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an accepted method of connection In some cases the company s inside wiring associated with a singleline individual service may be extended by means of acertified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent
33. k then The Power Stone beebips once Info Accepted followed by 3 bips Proceed 6 You may readback another register at this time or 7 You press 80 on your touchtone key pad saves programming The Power Stone bee bips twice exit You hang up Helpful Tip You can also change programming at any time before dialing 80 to exit Manual Operating mode Dialing 80 saves programming to memory and exits Manual Operating mode 4 Automatic Operation 4 1 Rings To Trip Feature The Power Stone will perform any of three selected power operations Automatic Operating Modes automatically when detecting ring voltage as a number of rings over the phone line from an inbound call The ring settings to trip your selected Automatic Operating Mode are available in two options 1 2Or Less Rings If The Power Stone detects two rings or less from an inbound callit will automatically perform the operating mode you have programmed In this option if The Power Stone detects more rings it will not be tripped therefore no automatic operation will occur 2 3 Rings or M ore Upon detecting a minimum of 3 rings on an inbound call The Power Stone will perform its automatic operating mode If it detects less than 3 rings 2 or less rings option 1 it will not be tripped no automatic operation will occur Good Stuff To Know Remember that the Rings To Trip feature option 2 o
34. nd on any standard electrical plug That s right these blades are standard size and are designed to plug into any standard grounded 120 Volt electrical wall outlet extension cord or power strip The key word here is grounded For maximum protection to you and your equipment only plug The Power Stone into grounded wall outlets extension cords or power strips Safety Tip If you use extension cord be sure itis capable of safely carrying the current required by your load Connecting To The Phone Line You will find on the left side of the Power Stone as you look at the face of the unit a 2 port RJ 11 telephone line receptacle One port is labeled LINE Take the supplied modular telephone line cord and plug end into the LINE port Plug the other end into the telephone wall jack The Power Stone is now connected to the phone line The other port labeled DEVICE allows you to connect any telephone equipment fax machine modem PC fax modem card ma telephone answering machine etc through The Power Stone to the phone line When an inbound call rings into your location The Power Stone will pass the ring voltage through to the equipment connected to the port labeled DEVICE When vou readv to program The Pow on site vou will be required to pl touchtone phon into the port labeled DEVICE Now That You re Comfortable Hopefully you venow gotten t
35. nswers your inbound call 2 You enter 8 8 on the touchtone phone The Power Stone bips 3 times Proceed 3 At that time you enter 011 01 for Operating Modes Register 1 and 1 for Passive On mode The Power Stone bee bips once Info Accepted then bips 3 times Proceed 4 We recommend that while in Manual Operating mode you readback any change to an operating mode AND the status of power supplied to your connected equipment before recording your programming and exiting manual operating mode This is done by pressing 01 for Operating Modes Register 1 and 07 for Power Status Register 7 5 You press 80 on your touchtone key pad Execute Programming The Power Stone bee bips twice You hang up Your equipment is now powered up To Enter Manual Operating Mode And Tum Power OFF To Your Equipment 1 The Power Stone or answering machine answers your inbound call 2 You enter 8 8 on the touchtone phone The Power Stone bips 3 times Proceed 3 At that time you enter 010 01 for Operating M odes Register 1 and 0 for Passive Off mode The Power Stone bee bips once Info Accepted then bips 3 times Proceed 4 We recommend that while in Manual Operating mode you readback any change to an operating mode AND the status of power supplied to your connected equipment before recording your programming and exiting manual operatin
36. or workmanship we will provide without charge for a period of one 1 year U S only the labor and the parts necessary to remedy any such defect Warranty period commences on the date of purchase by the original retail consumer The duration of any implied warranty of merchantability fitness for a particular purpose or otherwise on this product shall be limited to the duration of the applicable express warranty set forth above In no event shall we be liable for any loss inconvenience or damage whether direct incidental consequential or otherwise resulting from breach of any express or implied warranty of merchantability fitness for a particular purpose or otherwise with respect to this product except as set forth herein Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you To obtain service under this warranty you must present or send your product together with a copy of the retail sdle s original bill of sale your charge or credit card receipt or other satisfactory proof of the date of the original retail purchase of the product to any authorized service station A list of the authorized sevice stations can be obtained fmm your dealer or from Multi Link Inc This warranty does not cover damage which results from accident misuse abuse improper line volt
37. ou experiment with ring settings and how your local phone company sends its rings to your phone 4 2 Distinctive Ring Cadence Detection Feature Not only does The Power Stone give you a choice of two settings for the number of rings to trip your selected automatic operating mode but you can also select the type of ring cadence The Power Stone will react to Register 03 contains the three selectable ring cadence detect settings About The Distinctive Ring Service q G 5 As Your local phone company offers a service ais ay called Distinctive Ringing which allows you to have multiple phone numbers on a single phone line Each phone number when dialed will ring your phone with a specific Distinctive ring cadence Your original phone number rings with a single lt 0 long ring cadence your second phone number would ring with two short ring q d burst a third number rings a3 time burst a combination of one long and two short bursts j oO How The Power Stone Works With DR Service The Power Stone can be programmed to detect any one of the three standard Distinctive Ring cadences transmitted by your local phone company The ring cadences you have selected will be the only cadence The Power Stone will recognize All other ring cadences will be ignored In addition regardless of the ring cadences setting the
38. plication The possibilities and options are endless Your feature and operation selection depends on what equipment you want to control power to and how you want to do it Manual Control Remote or On Site You can control power to equipment plugged into the standard 120 Volt receptacle on the front of The Power Stone MANUALLY by a calling into The Power Stone s location entering your security access code and appropriate feature commands from a touchtone phone or b picking up the touchtone phone connected directly to The Power Stone and entering your security access code and appropriate feature commands Once you ve entered your security access code you can also command The Power Stone to give you an audible readback status on a how each individual feature is programmed b the status of power supplied to your equipment and c whether there has been a recent power outage at The Power Stone s location More in depth information about Manual Control can be found on page 15 but please continue to read on to get the big picture of how your fine product operates Automatic Operation You can program The Power Stone to control power via one of three automatic operating modes Power On Call Reboot or Toggle For a more in depth explanation of each individual operating mode and how they control power to your equipment see page 9 For Automatic Operation you are also required to program the Rings
39. pment If the light is blinking in a certain sequence here s what s going on f 1 OFF There is no power to The Power Stone STATUS The 120 Volt wall outlet is dead due to a power outage on that particular circuit or perhaps to your whole house 2 OFF Blinking On Briefly Once A Second The Power Stone is functional and has not been activated It is not supplying power to your equipment 3 ON Winking Off Once A Second The Power Stone has b n activated and is supplying power to your connected equipment 4 ON Solid The Power Stone isin Override mode and is supplying power to your equipment 5 ON Blinking Rapidly The Power Stone is in Manual Operating mode and ready for programming or readback 7 6 Circuit RESET Button At the bottom of The Power Stone is 15 Amp resettable breaker button This button resets The Power Stone in the event that you overload its circuit and trip the breaker Please pay special attention that you do not plug in multiple devices that could cause an overload to The Power Stone If The Power Stone circuit breaker continues to blow investigate the load requirements of each device that you have connected to The Power Stone s 120 Volt 15 Amp receptacle 8 Programming amp Quick Reference Guide REG REGISTER TITLE FEATURE DESCRIPTIONS W CONTROL NUMBERS YOUR SETTING OPERATI NG MODES RINGS TO TRIPI AUTOMATIC OPERATION DISTINCTM RING CADENCE SENSITIVITY
40. r less 3 or rings will only trip an automatic operating mode In other words it will only work when programmed in conjunction with one of the three selectable automatic operating modes see page 9 for anin depth explanation Passive Operating Modes Passive On and Passive Off ignore or are passive to all inbound call rings and control power without interference from inbound calls See page 10 for info about Passive Operating Modes The Rings To Trip feature does not cause The Power Stone to answer a call nor does it require a telephone device to go off hook answer the phone line to perform its function This means that you do not incur an extra long distance phone charge when calling in to trip The Power Stone from a remote Iccation All you have to do is ring The Power Stone with the appropriate number of rings and hang up the phone Neat huh Curveball From The Phone Company The number of rings you hear in the handset of your remote site telephone will probably not correspond exactly to the number of rings The Power Stone receives The discrepancy usually lies at the phone company If you have programmed the Rings To Trip feature at 2 less please ring The Power Stone two full rings before hanging up By doing that you can be sure The Power Stone will manage to hear at least one of those rings and trip your selected automatic operating mode We do advise that y
41. rings The Power Stone Audible Readback Response Answers with an OK tone then a PROCEED tone You have 30 seconds to begin the next command 4 You change the Operating Mode from Power On Call the factory preset to Reboot by dialing 13 01 selects Register 1 and 3 selects Reboot mode The Power Stone Audible Readback Response Answers with an OK tone then a PROCEED tone You have 30 seconds to begin the next command 5 You have finished programming the desired feature changes and wish to save them to memory and exit Manual Operating mode You dial 80 The Power Stone Audible Readback Response Answers with the OK tone twice The LED returns to normal blinking Check and see if your mom is on the other end of the line If so talk to her You don t call her enough If not hang up the phone NOTE If The Power Stone does not receive a command within 30 seconds it will give you an OK tone and exit programming mode without saving any changes Basically it is acting as if you have dialed 90 See page 17 the section titled Programrning Commands The Power Stone requires 10 seconds after either party goes on hook hangs up to reset itself Why is this important If you hang up on The Power Stone and immediately call back within 10 seconds chances are you will get a busy signal 9 3 AUDIBLE READBACK OF PROGRAMMING NUMBEFUSYM
42. ry again 10 INSTALLATION OVERVIEW you install The Power Stone is totally dependent on the type of equipment you wish to control power to and if this equipment needs access to the phone line Bdow are two general installation applications that should give you a good idea of how to get optimal performance when using The Power Stone 1 Controlling Power To Data Equipment That Requires Access To The Phone Line a The Power Stone is plugged into a 120 Volt wall outlet b The Power Stone is connected to the telephone line via the supplied line cord One end is plugged into the tdephone wall jack and the other end is plugged into the port labeled LINE 120 VAC WALL OUTLET INCOMING LINE TELEPHONE WALL JACK PC MODEM FAX MODEM CARD LAN SYSTEM c The data equipment you wish to control power to is connected to the 120 Volt receptacle on the face of The Power Stone d The data equipment PC modem fax card fax machine etc is connected to the phone line through The Power Stone by plugging the RJ II line cord from your equipment into the port labded DEVICE Helpful Tips This is the required installation when using the Power On Call Automatic Operating mode All auto answer equipment fax or modem devices is required to be connected through The Power Stone to the phone line for Power On Call to work properly Other operating modes will function in this installation such as Reboot
43. s Unauthorized duplication of this manual is a violation of U S and other copyright laws and unauthorized use of all or part of this manual may result in patent infringement Therefore THIS MANUAL IS TO BE USED ONLY WITH OR AS A MARKETING TOOL FOR THE POWER STONE Duplication of all or part of this manual without the permission of Multi Link Inc is prohibited
44. s or less Call in and let the phone ring twice then hang up no charge if it s long distance The Power Stone will supply power to the PC for 2 minutes Call back within 2 minutes to a receptive PC Helpful Tip Using a Distinctive Ring number as the only means to trip The Power Stone s operation is a great way to power up your PC Just call your DR phone number and The Power Stone will do its thing If you are using an answering machine on thesame phone line as your PC ignore B and utilize options A and C of recommended programming Some answering machines regardless of the ring pattern will try and answer all inbound calls how to get around the answering machine Program your answering machine to answer at 4 rings Set your modem to answer at 3 rings When you power up your PC internal modem with 2 distinctive rings or less options A and C and hang up nothing will answer the phone line But the next time you call within thetwo minute period the modem will grab the call before the answering machine 4 If You Want To Manually Control The Power Stone From A Remote Location Installation Either Installation 1 or 2 can be suitable for this application Refer to Installation Overview page 20 21 If your application does require that the equipment you are controlling power to be connected to a phone line you want to talk to it after you turn it on use Installation Number
45. ss Call in and let the phone ring neg a once or twice then hang no charge if it s long a ay distance The Power Stone will supply power to the eet PC for 2 minutes Call back within 2 minutes toa receptive PC Helpful Tip If you are using an answering machine on the same phone line as your PC choose B of recommended programming Program your answering machine to answer at 4 rings Set your modem to answer at 3 rings When you power up your PC modem with 2 rings or less and hang up nothing will answer the phone line But the next time you call in within the two minute period the modem will grab the call before the answering machine 2 If You Want To Automatically Reboot A PC But Not On Every Inbound Call Instaliation Hither Installation 1 or 2 is suitable for this application Refer to Installation Overview page 20 21 Recommended Operating Mode Reboot Recommended Programming Reboot Operating mode supplies power to your PC that is turned on until you call in to interrupt power The recommended Rings To Trip setting for this application is 2 rings or less Call in and let the phone ring twice then hang up no charge if it s long distance The Power Stone will interrupt power to the PC for 15 seconds then a ats resupply power Helpful Tip This application really doesn t work well come WE when you include an answering machine on the same phone line
46. tomer A commitment to your complete satisfaction AFTER THE SALE is our pledge If at any time you have a comment or question about The Power Stone call us at 1 800 535 4651 We want to hear from you And again THANKS for the opportunity to do business with you You are important to us Your Needs And Our Product Our engineering and marketing folks here at Multi Link have designed a feature rich product that can perform a very simple function control power to your equipment a number of different ways It is our intent with this manual to supply you with all the operational information needed to realize the full potential of The Power Stone While our focus is to get you up and running as quick as possible it is difficult to anticipate what specific information you will need to do this Here s what we suggest First look through the table of contents to become familiar with the manual layout and what features you think would apply for your application Definitely read the sections titled How The Power Stone Works An Overview and Down N Dirty Application Info For The Terminally Impatient These sections are pretty good for developing a basic concept for specific application We also recommend turning to page 14 and viewing the Programming and Quick Reference Guide to familiarize yourself with the programming of features If your power control needs are pretty P simple and you req
47. tone When the appropriate number of rings is detected from an inbound call The Power Stone will shut off supplied power for a minimum of 15 seconds We say a minimum of 15 seconds because The Power Stone begins the 15 second timing period after the caller stops ringing the phone After the timed 15 second period The Power Stone will restore power to your connected equipment Toggle In this operating mode The Power Stone will toggle or switch the power supplied to your equipment when each subsequent inbound call is detected For instance you have your living room light plugged into The Power Stone If the lamp is currently off an incoming call will toggle the lamp on The next cal1 will toggle it off again 5 Passive Operation 5 1 Passive Operating Modes Passive When programmed the Passive On mode The Power Stone will supply uninterrupted power to connected equipment regardless of inbound call activity Basically Passive On mode ignores all inbound rings regardless of the Rings To Trip feature setting This modeis used when you do not want an inbound call to interrupt your power to a connecred device Passive Off When in this operating mode The Power Stone does exactly what the feature name implies it NEVER supplies power to equipment regardless of inbound call activity Always ignores all inbound rings and will not supply power to equipment connected to The Power Stone
48. u ve read the manual thoroughly penciling in the feature changes on your Programming and Quick Refernce Guide You call your mom don t if it s long distance call somebody local and ask her to lay the phone down for a moment while you program this neat new Call Activated Power Controller you ve just purchased She says OK Here s What Happens You ve decided to customize your Security Access Code program the Rings To Trip feature to 2 or less and program The Power Stone for the Reboot automatic operaring mode 1 Because five seconds have more than elapsed since you initiated the callto your mom you can enter the manual operating mode You dial 8 8 on your touchtone phone connected to the DEVICE port The Power Stone Audible Readback Response Answers with a PROCEED tone The STATUS light is blinking rapidly You have 30 seconds to begin the next command 2 You customize your SAC from 88 factory preset to 8899 by dialing 0699 06 selects Register 6 Customized Security Code and 99 isthe additional numbers that make it 17 custom The Power Stone Audible Readback Response Answers with an OK tone then a PROCEED tone You have 30 seconds to begin the next command 3 You change the Rings To Trip feature to 2 or less factory preset 3 or by dialing 022 02 selects Register 2 and 2 means 2 or less
49. uire The Power gt Stone to operate in one mode all the ae cae time then the job is simple Just read the Programming and Quick Vy O 2 UIS Reference Guide the Manual Nt Operation Programming Of The G RE A EST Power Stone section and go for it Install The Power Stone program P U STOME R pertinent features and operating eee ae mode according to the manual directions and your application requirements and it s a done deal meant RINE If your power control needs are of a more complex variety and you want to master The Power Stone s full potential as aremote power control and feature readback device we suggest you dothis read the manual thoroughly hook up The Power Stone to a phone line and 120 Volt wall socket plug in your selected device connect a phone to the DEVICE port and plav_with it Hands on training is the best way to sharpen your operating skills instill confidence in The Power Stone s abilities and overcome any technophobia you may have Table of Contents The Power Stone Call Activated Power Controller Operations Programming Manual EB Saf ty Instructions ia 1 E How The Power Stone Works An 2 El Down N Dirty Application Info For The Terminally Impatient 5 ES 8 4 1 Rings To Trip
50. ween entering numbers characters Let s say you are in Manual Operating mode and you are programming a register You enter the register number and then take too long to enter the appropriate feature number You will receive an ERROR tone Programming Commands Save To Memory Exit After programming all feature values that you wish to change you will need to save the register settings to permanent nonvolatile memory and exit the manual operating mode This can be done by entering 80 At that time you will hear the OK tone twice The STATUS LED will indicate the appropriate operating mode sequence Even if there is a power loss to The Power Stone 41 programming is saved No Save Exit If you wish to dump any programming you ve done and exit the manual operating mode dial 90 At that time you will only hear the OK tone once The Power Stone will revert to the previous programmed operating mode and features Set Registers Factory Preset This command sets all program registers to the factory presets refer to the Programming and Quick Referente Guide When you dial 60 all registers automatically revert to factory preset The Power Stone will answer with an OK tone followed immediatedy by a PROCEED tone This command does not exit manual operating mode 9 2 An Overview of Programming This is the big picture of how to program The Power Stone Being the good consumer you are yo

Power Stone Manual v.1 - Multi

Contents

Download Pdf Manuals

Related Search

Related Contents