Storm Racing Drone (Type A) USER MANUAL V1.2
Contents
1. again If the transmitter is off push throttle stick to down position turn on the transmitter push throttle to middle switch the FMD switch Down 2 and Up 0 to take over the control again 6 Copyright 2015 HeliPal com Rights Reserved Compass Calibration Please follow the following procedures to calibrate the compass calibration mb FMD Down 2 and Up 0 1 Switch the FMD switch up and down quickly for 6 to 10 times The LED indicator on the drone will turn on constantly yellow 2 Fig 1 Hold your Multi rotor horizontal and rotate it around the gravitational force line about 360 until the LED on the drone changes to constant green and then go to the next step 3 Fig 2 Hold your Multi rotor vertically and rotate it nose down amp tail up around the gravitational force line about 360 until the LED turns off meaning the co Fig l Fig 2 calibration is finished 4 lf the calibration was successful calibration mode will exit automatically 5 If the LED keeps flashing quickly Red the calibration has failed Switch the control mode switch one time to cancel the calibration and then re start from step 2 NAZA V2 Manual It is important to learn more about the NAZA M V2 GPS Controller You can download the manual here http download dji innovations com downloads nazam v2 en NAZA M V2 Quick Start Guide en pdf 7 Copyright 2015 HeliPal com Rights Reserved Circuit Diagr2. 101010 5880MHz 000000 5780MHz 101000 5885MHz 110100 5785MHz 110110 5905MHz 010100 5790MHz 001010 5925MHz 100100 5800MHz 001000 5945MHz 000100 9 Copyright 2015 HeliPal com Rights Reserved Lost connection with radio controller If the drone cannot connect with transmitter Red LED inside the RX701 receiver blink rapidly that means the radio system is not bind successfully You need to do this re binding step below 2 Make sure you have NOTHING plugged into BATT port on the RX701 receiver On the transmitter select MODEL gt FIXED ID press ENT if it is showing the code then press ENT again press one more time till it is showing RUN press R to choose NO press ENT again it s showing FIXID press R again to choose OFF then press EXT and turn off transmitter Plug the bind plug into Batt port on the RX701 receiver with this plug still in BATT port and power up the drone you will see receiver flashing red slowly then means old code has been erased unplug drone battery and remove this bind plug Now you need to activate the Fixed ID function Turn on transmitter and then make sure Throttle Stick is all the way down all trimming is neutral both corner FMOD switch and Throttle Switch is off pointing backward and all switches on the transmitter pointing upward then turn off transmitter Connect drone battery the receiver will start flashing place drone on flat surface Turn on transmitter
3. GEAR 83 0 83 5 FUNCTION gt REVSW gt ELEV NORM FUNCTION gt TRVAD gt FLAP U88 D88 FUNCTION gt REVSW gt AILE NORM FUNCTION gt TRVAD gt AUX2 100 100 FUNCTION gt REVSW gt THRO NORM FUNCTION gt REVSW gt RUDD NORM 8 FUNCTION gt SAFE gt ELEV HOLD FUNCTION gt REVSW gt GEAR REV FUNCTION gt SAFE gt AILE HOLD FUNCTION gt REVSW gt FLAP REV FUNCTION gt SAFE gt THRO SAFE L100 FUNCTION gt REVSW gt AUX2 REV FUNCTION gt SAFE gt RUDD HOLD FUNCTION gt SAFE gt GEAR SAFE 40 FUNCTION gt SUBTR gt ELEV 0 FUNCTION gt SAFE gt FLAP HOLD FUNCTION gt SUBTR gt AILE 0 FUNCTION gt SAFE gt GYRO HOLD 10 Copyright 2015 HeliPal com Rights Reserved
4. Storm Racing Drone type with Naza V2 GPS Flight Controller USER MANUAL V1 2 1 Copyright 2015 HeliPal com Rights Reserved DISCLAMIER Please read this disclaimer carefully before using this product This product is a hobby with motor but not a toy which is not suitable for people under the age of 18 By using this product you hereby agree to this disclaimer and signify that you have read them fully You agreed that you are responsible for your own conduct and content while using this product and for any consequences thereof Before you fly the drone 1 Make sure all connections are good and keep children and animals away during flying firmware update system calibration and parameter setup 2 Always fly the drone away from unsafe conditions such as obstacles crowds high voltage lines etc 3 Do not use in bad weathers such as rainy day snow windy more than moderate breeze hail lighting tornadoes hurricanes etc 4 Check whether the propellers and the motors are installed correctly and firmly before flight Make sure the rotation direction of each propeller is correct 5 Check whether all parts of the drone are in good condition before flight Do not fly with aging or broken parts 6 Never overcharge LiPo batteries Do not charge above 4 2V per cell When the battery is fully charged disconnect it from the charger Never leave the battery charger unattended during charging 7 Never discharge batte
5. am Clockwise Anti Clockwise RX701 Receiver VERY IMPORTANT Video Transmitter gt iOSDmini overlap flying informatin on video Clockwise GPS Antenna Anti Clockwise Rear Compass Motor 1 Battery TRUM ee DEVO 40 57441 2 4GHz Ses 39039990 Video Transmitter AY14510 N33825 NO qso GPS Antenna Compass 8 Copyright 2015 HeliPal com Rights Reserved System TS5823 video transmitter has up to 32 different video channels available to avoid interference with other channels If two or more drones are flying at the same time ON KE i try to select different video frequency to avoid ete video interference bigger different in video frequency between drones the less interference generated Default Setting is channel 5665M Always check the supported channels of you FPV reception devices such as monitor goggle Frequency Table Frequency Switch 123456 Frequency Switch 123456 5645MHz 001100 5805MHz 001110 5665MHz 101100 Default Channel 5809MHz 110010 5685MHz 011100 5820MHz 110000 5705MHz 111100 5825MHz 101110 5725MHz 000110 5828MHz 010010 5733MHz 111010 5840MHz 010000 5740MHz 111000 5845MHz 011110 5745MHz 100110 5847MHz 100010 5752MHz 011010 5860MHz 100000 5760MHz 011000 5865MHz 111110 5765MHz 010110 5866MHz 000010 5771MHz
6. ries to below 3 3V per cell 8 Remove batteries when not using the drone 2 Copyright 2015 HeliPal com Rights Reserved Package includes Fully Assembled Storm Racing Drone GPS w DJI V2 GPS System Built in FPV System Camera and Transmitter DJI iOSD Mini Module Overlay flight data information Walkera DEVO 7 Radio System 14 8V 2200mah 30C Li Po Battery 6pcs Clockwise 6045 Dual Blade Propeller 4 of them are spare parts 6pcs Counter Clockwise 6045 Dual Blade Propeller 4 of them are spare parts SKYRC E4 Battery Charger 1 5 mm Hex Wrench 10 2 0 mm Hex Wrench 11 10mm Hex Nut Driver Driver for motor cap 12 5 5mm Hex Nut Cross Wrench for airframe 13 Battery Warning Buzzer 3 Copyright 2015 HeliPal com Rights Reserved Quick Start 1 FMD Up 0 GPS Mode 2 Throttle Down Mode 2 Left Stick 3 Power On 4 Stand Up Antennas 5 Check Battery Level 7 4 2V per cell Full m 4 Alarm to 3 6V or above ik y gt 6 Put the drone an open area with good GPS signal and then connect battery to drone 7 Wait for around 1 minute until green LED blank rapidly That means GPS signal is ready and ready to fly 8 Unlock the system Left Stick Left Bottom Right Stick Right Bottom 9 You can fly it now 10 When the red LED blanks rapidly it means low battery land it immediatel
7. y Control FLIGHT MODE UP 0 GPS MODE MID ATTITUDE MODE DOWN 2 ATTITUDE MODE Up FORWARD TURN TURN a 9 RIGHT NES POWER SWITCH MODE 2 LEFT THROTTLE STANDARD FLIGHT MODE UP 0 GPS MODE MID ATTITUDE MODE DOWN 2 ATTITUDE MODE G FORWARD A TURNZ TURN LEFT RIGHT LEFT RIGHT POWER SWITCH MODE 1 RIGHT THROTTLE 5 Copyright 2015 HeliPal com Rights Reserved Auto Go Home If the drone has been started up correctly and the GPS signal is good with 6 or more satellites are found the drone can undergo Go Home features when it lost signal with radio controller 1 Ifthe attitude of the drone more than 20 meters it will go home horizontally 2 If the attitude of the drone below 20 meters it will ascend to 20 meters and go home horizontally 3 If the attitude of the drone is below 20 meters and behind an object there is high risk of crash during ascends 4 If the drone go home path is blocked by object there is high risk of crash during auto go home process Important How to take over the control again during Auto Go Home When the drone is undergoing auto go home feature you can take over the control again by performing the following procedures If the transmitter is on push the throttle stick to FMD and eO middle position and then switch the FMD Switch Down 2 and Up 0 and you can control the drone
8. you should see black box running on the transmitter screen do not touch anything or you will break the searching mode Do not touch anything around 7 10 seconds until transmitter stop flashing and you will see the RX701 receiver have solid light that means binding has completed On the transmitter go to MODEL gt FIXED ID turn it ON then press DN button to confirm the code then press ENT and press ENT again to confirm it will ask you to RUN choose YES and press ENT From now on your receiver is bound to this memory on your DEVO 7 Radio Controller Parameters If you reset your radio controller Devo 7 setting you can apply the setting below 1 2 MODEL gt TYPE gt AERO FUNCTION gt SUBTR gt THRO 0 FUNCTION gt SUBTR gt RUDD 0 MODEL gt INPUT gt FM SW FMD FUNCTION gt SUBTR gt GEAR 5 5 MODEL gt INPUT gt FM TRM COMM FUNCTION gt SUBTR gt FLAP D5 0 MODEL gt INPUT gt HLDSW HOLD FUNCTION gt SUBTR gt GYRO 0 FUNCTION gt SUBTR gt AUX2 0 MODEL gt OUTPUT gt GEAR FMD and ACT MODEL gt OUTPUT gt FLAP MIX and ACT 7 FUNCTION gt TRVAD gt ELEV U100 D100 MODEL gt OUTPUT gt AUX2 AUX2 and ACT FUNCTION gt TRVAD gt AILE L100 R100 FUNCTION gt TRVAD gt THRO H100 L100 MODEL gt AMPLI gt 20 FUNCTION gt TRVAD gt RUDD L100 R100 FUNCTION gt TRVAD gt
Download Pdf Manuals
Related Search