Anaheim Scientific H200 Single Channel Thermocouple
Contents
1. 3 Using the Up Button 4 7 Fig 1 to increase the offset value and or the Down Button 4 6 Fig 1 to decrease the offset value 4 Release all buttons to go to the normal measurement screen The meter wil now display measured values with the offset already calculated in to the reading 4 5 Measuring Considerations 1 When inserting the measurement probes in to the Thermocoupk Input Socket 4 10 Fig 1 not the correct polarity usually indicated by the size of the plug blades negative usually being the wider of the two 2 For the most accurate reading allow the probe to stabilize when it is being introduced in to an environment thatis significantly different in temperature fromits starting point 4 6 Data Hold Mode 1 During a measurement press the Hold Button 4 3 Fig 1 to hold the displayed value on the LCD The HOLD symbol will also be displayed on the LCD 2 Pressing the Hold Button 4 3 Fig 1 will release the data hold function 4 7 REC Mode 1 To record the maximum and minimum readings press the REC Button 4 4 Fig 1 The REC symbol will be displayed on the LCD By pressing the REC Button 4 4 Fig 1 you can toggle through the Max and Min values 2 To stop using the REC function press and hold the REC Button 4 4 Fig 1 for atleast 3 seconds 4 8 REL Mode 1 Itis recommended that you memorize the value on the LCDdisplay first Also note that the REL f2. 110 1000 C 0 2 1 C 58 0 to 2102 0 F 0 2 1 F 0 2 18 F 50 1 to 1000 C 0 2 1 C Type J oF 58 0 to 2372 0 F 0 2 1 F o E 49 58 1t0 1480 F 02 18 oe 50 00 1150 0 C 0 2 05 1 F l 1 C z 1 F 1 C 14 F C 1 F 58 010 752 0 F 02 1 F 50 0 to 400 0 C 02 0 5 58 1 t0 1480 F 0 2 18 50 110 1000 C 0 2 1 C 50 110 1000 C 02 1 C 58 0 to 1652 0 F 0 2 1 5 F Type E 58 110 1480 F 0 2 18 F 0 to 600 C 1 5 C a 60110 1700 C 15 5 C y 3210 1112 F 1 10 F 1113 to 3092 F 15 10 F Data Hold Display freeze Saves MAX or MIN values with recall 58 1 to 1480 F 50 0 to 900 00 02 080 Sampling Time Approximately 1 second Over Range Indicator erro LU Data Output RS 232 Serial data output Operating Environment 32 to 122 F 0 to 50 C lt 80 R H Sa 6 Pieces of DC 1 5V Batteries UM4 AAA or Power Supply equivalent Weight approx 0 62bs 2809 Dimensions approx 6 9 x 27x 1 7 174 x68x 42mm Included Accessories Instruction manual battery carrying case Note Accuracy applicable in environments with temperatures between 20 C to 26 C and only applies to the meter itself not the probe Specifications and information are subject to change without notice Please visit www anaheimscientific com for the most current product information 4
3. Operating Instructions 4 1 Unit Diagram 4 10 Fig 1 4 1 Display 4 8 RS232 Socket 4 2 Power Button 4 9 Battery Compartment 4 3 Hold Button 4 10 Thermocouple Input Socket 4 4 REC MAX MIN Button 4 11 Stand 4 5 Sensor Button 4 13 Tripod Screw Mount 4 6 REL Button 4 12 Battery Cover Screw 4 7 C F tt Button 4 2 Measuring Procedure 4 3 Thermocouple Measuring Procedure 1 Power on the meter by pressing the Power Button 4 2 Fig 1 The meter will go through a short self test 2 Select the sensor type by pressing the Sensor Button 4 5 Fig 1 As you press this button multiple time the meter will display the sensor type along the bottom of the LCD You will see it change between K J T E amp R 3 Once you have setit for the desired sensor type insert the probe in to the Thermocouple Input Sockef 4 10 Fig 1 4 Select the unit of measure by pressing the C F Button 4 7 Fig 1 5 Insert the Thermocouple in to the environment you wish to measure The LCD wil display the measured values 4 4 Offset Value Adjustment In some environments or applications there may be some need to offset the displayed temperature value After following section 4 3 follow these steps to seta offset value 1 Simultaneously press and hold the Hold Button 4 3 Fig 1 and REC Button 4 4 Fig 1 2 The LCD willdisplay the starting value in the bottom ofthe LCD and the value in the middle section
4. ANAHEIM SCIENTIFIC Division of BK PRECISION INSTRUCTION MANUAL Models H200 Single Channel K J T E R Thermometer CE Table of Content 1 Product Introduction cocccconnonccnccnncnccncnanananncnnos 3 A PEPELEPIFFEEEEFELEEEELETEFFEFPEPEIRERCE 3 1 2 Applicatons anne eos 3 2 Safety Information uusssunnnnenennnnnennnnnnnnennnnnnnennnn 4 ZAC Scala cia 4 2 2 Safety OT 4 A ehe 5 4 Operation Instructions uuussesnennennnnnnnnnnnnnnnnnnnn 6 4 14 Unit Diagram a2 6 4 2 Measuring Procedure oooooooccccnnooccccciocnncccnos 7 4 3 Thermocouple Measuring Procedure 7 4 4 Offset Value Adjustment 0cceeeeeeeeeeeeees 7 4 5 Measuring Considerations c0cceeeeeeees 7 4 6 Data Hold Mode ccccceeceeseeseeseeseeeeeseeeeees 7 4 7 Rec Mode cececceeeeeeceeeeeeeeetseeeeeeeeeees 7 4 8 RELMOGS seen 8 5 Auto Power Off Disable aeee 8 6 RS232 PC Serial Interface Information 9 7 Battery Replacement uunsesnnensnnnnnnnnnnnnnnnnnnnnnnnn ann 11 8 Service Information uussssrnennnnnnnnnn nennen nem nn 12 9 Warranty Information uuersssnnnnnnnnnnnnnnnnnnnnnnnnnnnnn ann 13 To see all available accessories and downloadable software please visit www anaheimscientific com 1 Product Introduction 1 1 Features Measures temperature from five different types of thermocouples 0 1 Resolution Fast response time High l
5. evel of accuracy Large LCD display Two year warranty 1 2 Applications Science Experiments HVAC Plant Maintenance Manufacturing Agriculture Quality Control 2 Safety Information A Read the follow ing safety information carefully before attempting to operate or service the meter Only qualified personnel should perform repairs or servicing not covered in this manual 2 1 Cautions m DO NOT submerge the products mentioned in this manual in water or any other types of liquids m This product is not designed for use in medical applications The product can only be used to measure body temperature simply for reference 2 2 Safety Symbols Dangerous refer to this manual before using the meter E Conforms to requirements of European Union and European Fare Trade Association EF TA lt a Battery level is low E lt Don t dispose this product as unsorted municipal waste This instrument conforms to the following standards EN61326 Electrical equipment for measurement control and laboratory use 1EC61000 4 2 Electrostatic discharge immunity test 1EC61000 4 3 Radiated radio frequency electromagnetic field immunity test 1EC61000 4 8 Power frequency magnetic field immunity test 3 Specifications Unitof Measurement Temperature Compensation Automatic for cold junction on K amp J type Thermocoupk Types K J T E amp R Thermocoupk Type Resolution Range Accuracy Type K 0 0 0 0 0 0 0 1 50
6. indicates the following status Polarity 0 Positive 1 Negative D12 amp D11 F 02 Decimal Point DP position fromright to left 0 NoDP 1 1DP 2 2DP 3 3DP Display reading D1 LSD D8 MSD Example If the display reading is 1234 D8 to D1 then D8 to D1 is 00001234 poo End Word RS232 Setting Baud Rate 9600 Data bit 8 Data bits Stop bit 1 Stop bit 10 7 Battery Replacement a 1 When the LCD display shows the CT law battery symbol It is necessary to replace the battery The specifications listed for this instrument do not apply when the low battery symbol is displayed 2 Open the Battery Compartment 4 9 Fig 1 by first loosening the Battery Cover Screws 4 12 Fig 1 3 Replace the batteries with good batteries noting the correct polarity Replace Battery Compartment 4 9 Fig 1 and Battery Cover Screws 4 12 Fig 1 Ensure the cover is securely fastened 8 Service Information Warranty Service Please return the product in the original packaging with proof of purchase to the address below Clearly state in writing the performance problem and return any leads probes connectors and accessories that you are using with the device Non Warranty Service Return the product in the original packaging to the address below Clearly state in w riting the performance problem and return any leads probes connectors and accessories that you are using w ith the device Cust
7. omers not on open account must include pay ment in the form of a money order or credit card For the most current repair charges please visit www anaheimscientific com and click on service repair Return all merchandise to Anaheim Scientific w ith pre paid shipping The flat rate repair charge for Non Warranty Service does not include return shipping Return shipping to locations in North American is included for Warranty Service only For overnight shipments and non North American shipping fees please contact Anaheim Scientific Anaheim Scientific 22820 Savi Ranch Parkw ay Yorba Linda CA 92887 www anaheimscientific com 714 921 9095 Include with the returned instrument your complete return shipping address contact name phone number and description of problem 9 Limited Two Year Warranty Anaheim Scientific w arrants to the original purchaser that its products and the component parts thereof will be free from defects in workmanship and materials for a period of two years from date of purchase from an authorized Anaheim Scientific distributor Anaheim Scientific will w ithout charge repair or replace at its option defective product or component parts Returned product must be accompanied by proof of the purchase date in the form of a sales receipt To obtain w arranty coverage in the U S A this product must be registered by completing the w arranty registration form on www anaheimscientific com w ithin fifteen 15 da
8. unction does notwork when the meter is in Data Hold or Data Record conditions 2 To remove any displayed value fromthe LCD you can press the REL Button 4 6 Fig 1 The display will then go to zero and you will see the REL marker in the top portion 3 All subsequent values displayed wil be the measured value minus the amount on the display when the REL button was pressed 4 To cancel the REL function simply press the REL Button 4 6 Fig 1 The REL marker will then disappear fromthe LCD 5 Auto Power Off Disable This instrument has a Auto Power Off function that can prolong battery lie The meter will shut off automatically if none of the buttons are pressed in approx 10 min To disable this function select the memory record function during a measurement by pressing the REC Button 4 4 Fig 1 6 RS232 PC Serial Interface Information This instrument has RS232 PC serial interface via a 35 mm terminal 4 12 Fig 1 The dat outputis a 16 digit streamwhich can be utilized for user s specific application ARS232 lead wit the following connection will be required to link the instrument with the PC serial port Visit www anaheimscientific comto see any available downloadabk software for your instrument Center Pin 3 5 mm jack plug Ground shield resister The 16 digit data stream will be displayed in the following format D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1DO Each digit
9. ys of purchase Exclusions This warranty does not apply in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs The warranty is void if the serial number is altered defaced or removed Anaheim Scientific shall not be liable for any consequential damages including without limitation damages resulting from loss of use Some states do not allow limitations of incidental or consequential damages So the above limitation or exclusion may not apply to you This w arranty gives you specific rights and you may have other rights which vary from state to state Anaheim Scientific 22820 Savi Ranch Parkw ay Yorba Linda CA 92887 www anaheimscientific com 714 921 9095 Anaheim Scientific 22820 Savi Ranch Par kw ay Yorba Linda CA 92887 U S A www anaheimscientific com Printed in Tawan Ver 1 0 0606 2006 Anaheim Scientific Corporation
Download Pdf Manuals
Related Search