User manual of U-Prox proximity readers
Contents
1. User manual of U Prox proximity readers U Prox KeyPad U Prox mini Function U Prox proximity readers is intended to be applied in different access control systems using RS232 Touch memory Wiegand 26 Wiegand 37 or Wiegand 42 interface Reader U Prox KeyPad have built in keypad Types of identificators Integrated Technical Vision Ltd manufactures readers operating with amplitude ASK and frequency FSK modulation proximity cards and tags Design The reader is placed in miniature hermetic plastic case Thanks to the small overall dimensions the reader is distinguished for its advanced reliability Specifications Warm up time 10 seconds after power start Case Material ABS plastic Dimensions U Prox KeyPad U Prox mini mm 120x65x17 5 80x45x13 5 Weight U Prox KeyPad U Prox mini gramm 240 70 Ambient Conditions U Prox mini U Prox KeyPad Temperature 35 60 C 0 55 C Humidity 100 without condensate Power supply U Prox mini U Prox KeyPad Voltage 4 75 16 Vof 9 16 V of direct direct current current Current up to 30 mA up to 40 mA Maximal current up to 60 mA up to 75 mA Voltage ripple up to 500 mV Distance of reading Typical reading distance show in table 1 and depends on tag type used with it This parameter is valid for power supply voltage range from 9 to 16 VDC and ripple up to 150 MVp p U Prox mini U Prox KeyPad Distan2. ce mm 100 120 100 120 Table 1 Wiring Table 2 Reader has 8 wire colored W2 W3 W4 RS232 Touch Memory cable intended for WS connection to access Color Function control panel Green Data 0 Rx iButton Table 2 The wires White Data 1 Tx assignment Red V V V Multiwire signal cable with Black GND GND GND 0 22 mm wires cross Brown Red Led Red Led sectional is recommended Orange Green Led Green Led to use for connection of the Blue Beep Beep reader and control panel Yellow Hold Synch Hold Synch Hold Synch Using this cable the maximum length of 100 30 for Touch Memory meters can be obtained Type of interfaces The proximity reader is intended to be applied in different access control systems using RS232 Touch memory Wiegand 26 Wiegand 37 Wiegand 42 Mounting lt ow It is recommended to mount the reader on a wall closely to a door at appropriate height Do not mount the reader on metal surface since it causes decreasing of reading distance If two readers are mounted at a distance less than 50sm reading distance of a card may be reduced appreciably In such a case connect yellow wires of the readers The readers will synchronize and work in turn Synchronization allows mounting of two readers at a small distance to the extent of reading distance of a card In case that two readers are mounted at a distance less t
3. han reading distance of a card the card may be read by the reader behind the wall To mount the U Pox KeyPad U Pox mini readers proceeds as follows Remove the boot in the bottom part of the reader with loosing the screw Push mounting panel towards the screw and remove it from the reader Using the mounting panel as a template mark and then drill two openings 6mm in diameter and 35mm deep Pass the wire through central opening Secure the mounting plate on a wall using plastic nailing plugs and screws Connect the reader to the control panel s cable Put on the reader on the mounting plate push the case down against stop and secure the reader with the screw Put on the boot The Reader Operation Reading of identificator code The code reading is annunciated by built in buzzer and two color LED according to interface type and annunciation mode refer to Data transfer and Annunciation Repeated reading will be available after 0 8 sec if the identificator is moved away from the reader sensing area Hold Mode Reader is turned to the hold mode while yellow wire is closed to the ground In this mode reader does not read cards thus current consumption decreases to 30mA Do not apply voltage to hold outlet Data transfer and Annunciation While reading card code the reader produces a short sound signal and switches green LED for a short time This confirms that the card code has been read successfully but is not related
4. ntrol packet to the reader Packets should be transmitted with 2 400 bits per second 8 bit data no parity 1 stop bit Packet format Bit 7 6 5 4 3 2 1 byteO 0 1 0 0 1 0 0 1 byte 1 red red blinks steady byte2 green green buzzer buzzer steady blinks pulsatory uninterruptedly 1 corresponds to LED or buzzer switching on LED blinking and buzzer pulsatory control bits have the highest priority Annunciation does not change until next control packet is received Reader transmits data as follows byte 0 1 10 11 12 Card read 23h data C sum ODh PIN entered 21h data C sum ODh data Bit 7 6 5 4 3 2 1 0 Destination 0 0 1 1 X X X X Checksum exclusive OR of low nibbles of bytes from 1 to 10 high nibble of always must be 3h Example Card code 7E000460AA will be sent as 23h 37h 3Eh 30h 30h 30h 34h 36h 30h 3Ah 3Ah 3Bh ODh Limited Warranty Integrated Technical Vision Ltd warrants that for a period of 24months from the date of purchase the product shall be free of defect in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Integrated Technical Vision Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship and no
5. t damages incurred in shipping or handing or damages due to causes beyond the control of Integrated Technical Vision Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be lieu of any and all other warranties whether expressed or implied and of all other obligations or liabilities on the part of Integrated Technical Vision Ltd This warranty contains the entire warranty Integrated Technical Vision Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any warranty or liability concerning this product In no event shall Integrated Technical Vision Ltd be liable for any direct indirect or consequential damages Loss of anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product
6. to the rights of the card within the system E g right to enter Green or Red Led and buzzer are used by controller to indicate the decision made by the system with respect to the presented card To switch a green LED on valid card entry connect Brown wire Red LED And Orange wire Green LED together to negative LED output of the Controller Wiegand Interface Engaging of LED and buzzer is possible automatically or by closing of corresponding wire to the black wire GND according to Table 3 Table 3 Annunciation mode X Buzzer Red LED Gren LED 00 Beep on card read Normally ON switched OFF Blinks at reading at reading 01 Outside control Normally ON switched OFF Blinks at reading at reading 02 Beep on card read Switched OFF Blinks at reading 03 Outside control Switched OFF Blinks at reading 04 Beep on card read Normally ON switched OFF Outside control at reading 05 Outside control Normally ON switched OFF Outside control at reading 06 Beep on card read Outside control Outside control 07 Outside control Outside control Outside control 08 Beep on card read Normally ON switched OFF Blinks at reading Availability to switch ON at reading Availability to Availability to switch from outside switch OFF from outside ON from outside Data transmissions from reader comply with the standard specified RS232 interface To control annunciation send three byte co
Download Pdf Manuals
Related Search