Home

INSTALLATION, OPERATIONS AND USER`S MANUAL

1. 32 Optional Swim Mirror The Swim Mirror helps with stroke technique and makes your swimming workout fun The Swim Mirror described more fully in the Supplemental Guide is made from durable stainless steel and is attached with three stainless steel screws which are already attached to the housing just below the swim propulsion housing When a deeper pool is selected make sure that the shallower area extends at least 13 beyond the front Water Return Channel to accommodate the Swim Mirror Swim Mirrors are easily sent by UPS ground and may be ordered later 33 Optional Synthetic Coping System An ideal solution for indoor installations the Synthetic Coping System finishes off an Endless Pool quickly and easily Typically used when the pool is installed partially or fully aboveground the Optional Synthetic Coping System provides a finished 9 3 4 wide waterproof edge to your pool Made of synthetic boards and corner pieces with shiplapped joints the system comes in a variety of colors Please refer to Supplemental Guide for additional installation information 21 Operations and Maintenance User s Manual Included with your Endless Pool and packaged with your Water Quality System WQS are products to help with start up and on going maintenance These include 1 Container calcium hardness increaser 1 Container water clarifier 1 Container pH decreaser 1 Container pH increaser 1 Container total alkalinity in
2. Output ratings Output Voltage Current Typical Device Out 1 120 240V 17FLA Pump 1 Out 3 120 240V 0 8 A Circulation Pump CP Blower Out 4 120 240V 1A Ozone Generator Out 5 120 240V 5A Audio Video device L1 Light 12VAC 0 1 A CO C1 Communications port S Top side controller CO Comm connector in stik UL CSA Standards UL 1563 Fifth Ed File E182156 CSA No 22 2 218 1 M89 TUV Standards EN IEC 60335 2 60 EN55014 1 EN55014 2 EN61000 3 2 EN61000 3 3 Circulating Pump The circulating pump has been provided with an integral dry run protection thermostat feature that turns the pump off when the pump runs dry thermostat off at 212 F 10 F If left unat tended the thermostat will automatically reset within a relatively short amount of time when the unit cools down thereby allowing the pump to again begin operation at 176 F 13 F Depending on the system conditions many times one or two of these off on cycles will correct an air bound dry run condition by itself with no harm done to the pump thereby allowing continued trouble free operation However if the off on cycling persists then meas ures should be taken to correct the problems in the circulation sys tem causing the on off cycling Floating Thermal Cover Endless Pools Inc provides a lightweight cover for the Endless Pool if a retractable security cover has not been purchased This cover floats on the water surface insul
3. GALVANIZED POOL FANELS STEEL POOL PANEL 9 Liner Underlayment 28 MIL LINER HANGER If it is possible finish the rest of the pool area especially eege SUPPORT the ceiling over the pool before proceeding This will help ALUMINUM COPING ensure that the liner is not damaged and also keep the pool Fig I CORNER DETAIL water skimmer and filter free of construction debris Vacuum the pool floor carefully and make sure there are no sharp bumps that might damage the liner Take special care to remove any metal chips that may have fallen on the floor If you have purchased the Anchor Bolt Kit then that will x come with a roll of closed cell foam Install the protective Foam Corners foam underlayment on the floor of the pool The foam kit SE EN E Sp comes in a box with the four foam corners and a can of the panel height spray adhesive The foam is 3 5 x 32 For wider pools cut pieces as appropriate to cover the floor of the pool Place seams near the walls of the pool so that they will be covered by the Water Return Channels Secure the foam to the floor with the spray adhesive provided With deeper pool instal lations and larger pools a second and sometimes even a third box of foam has been provided Secure the foam to the bottom and walls of the deeper area as well as to the floor of the pool If you have purchased the Floor Leveling Kit then that will come with loose fill vermiculite and sheets of plastic floor ing Th
4. Doing so will give you an idea of how suitable your water source is for swimming pool use Testing the water can be done by using your Taylor test kit A local swimming pool supply store can also test your water at a minimal charge Take a copy of the Water Chemistry Testing Log with you Well Water Certain geographic areas are high in mineral content For pools where well water is to be the water source strong consideration should be given to having water tanked in Well water often has high iron calcium and mineral content which is not ideal for your swimming pool If well water is the only available source please call our Customer Service Department or seek advice from a local pool store ENDLE SS POOLS Hard Water and Water Softeners The phrase hard water refers to having high levels of calcium in the water Many homes that have hard water will often have a water softener installed in their homes that lowers the level of cal cium in the water For ideal water conditions in a vinyl liner pool the calcium hardness level should be between 180 250 ppm Please call us to discuss your options if you have a water softener and or high calcium in your water supply Nature 2 Sanitation of your pool water is partly accomplished by placing one Nature2 purifier into the filter cartridge at the front of your pool The Nature 2 system included in your pool kit significantly reduces the amount of chlorine you ll nee
5. OF LINER HANGER BY OTHERS A SELF geg LINER HANGER 4 ABS SHIM OR 1 GALVANIZED STEEL REINFORCING CHANNEL GALVANIZED STER POOL PANEL 28 MIL PVC LINER ENDLESS POOLS 7 Liner Hanger Cut the liner hanger with a hacksaw at the point where 2 sections overlap Repeat at every point labeled A Va The ends of 2 adjacent liner hanger sections should meet at this point en Repeat for the other side D D ae mee emer a d d sew error e wm E mmm A mm e e e vm wm E he K Attach the liner hanger to the panel with the provided self drilling screws Use 2 screws per notched section and approx every 18 along the sides EE e EN Bend notched liner hanger into place as shown Repeat for all 4 corners Fig 8 8 Optional Liner Hangers Optional Bullnose Coping System Typically used when the pool is installed fully in ground the Optional Bullnose Coping System allows the installer to fin ish with concrete and or tile right up to the water s edge The aluminum bullnose coping system acts as both a liner hanger and a finished edge Endless Pools Inc supplies precut pieces to fit the specific pool size ordered Included in the kit are radius corners and straight pieces to provide a finished look These extrusions are fastened down to the top flange of the pool panels through the PVC shims and the reinforcing ch
6. pH level must be maintained between 7 4 and 7 8 and total alkalinity between 80 and 120 ppm Total dissolved solids TDS must be no greater than 3 000 ppm All orders are FOB Aston PA We will NOT be liable for any costs or losses due to changes in shipping schedules or delivery times It is the responsibility of the Customer to supply safe and proper site preparation installation and operation for all Endless Pool Swim ming Machines This includes but is not limited to adequate drainage at any pool and or equipment site to control humidity to post necessary safety signage and to ensure safe and proper use of all Endless Pool Swimming Machines Customer shall be responsible for any and all building permits fees licenses and authorizations necessary to comply with local building codes or requirements Customer takes all responsibility for site preparation including but not limited to any slab or foundation Any Endless Pools product installed above grade must be placed on a properly engineered structure which is the responsibility of the customer We make no warranty whatsoever in respect to accessories or parts not supplied by Fitness Machines LLC directly The term original purchaser as used in this warranty shall be deemed to mean the person for whom the Endless Pool was originally installed We DO NOT warrant this machine to meet requirements of any safety code of any state municipality or other jurisdiction Purchaser assumes a
7. seem intimidating simply follow the instructions on the underside of the test kit lid These instructions walk you through each of the tests step by step and they are color coded with the appropriate reagent bottles to use for that test When performing the water quality tests write down your results on the log sheet provided at the end of this bulletin We would strongly urge you to make copies of these blank logs for use in the future Any observations chemical additions or actions taken should also be noted While it may seem a bit tedious all of this information will prove invaluable in the event of a water quality problem or when you go to make similar adjustments to the water chemistry in the future During this start up period which will last a few days you will need to Balance the pool water by following the instructions listed below After this initial start up period the testing proce dures and emphasis are a little bit different and they are explained in the Maintaining your Endless Pool instructions a few pages later in this manual The following steps need to be followed when the pool is first filled as well as anytime the pool is partially drained and refilled They will walk you through testing and adjusting the factors af fecting the balance of the water i e the water s total alkalinity pH and calcium hardness levels The level of chlorine inside the pool as long as it is not above 5ppm wil
8. If you will not be using the pool during the winter in an area where freezing is a problem special consideration must be taken to protect the pool and ancillary equipment if either is located outside If you have any questions regarding precautions to take against freezing please call our Customer Service Department at 800 910 2714 26 1 Poolside Water Quality System Troubleshooting Symptom No power to controller No Keypad Display FLO Reading on Display Circulating Pump Makes Noise Pool taking long time to heat Possible Cause 1 Tripped breaker 2 Disconnect turned off 3 Improperly wired controller 1 No power to controller 2 Keypad cord not attached 3 Pins in display receptacle are bent 4 1 2 amp fuse blown in heater controller 1 Pump housing not filled with water 2 Water level too low 3 Filter is dirty 4 Ball valve is closed or return line is plugged 5 Circulating pump is not plugged in 6 Swim current turned on 7 Circulating pump turned off at keypad 8 10amp fuse in heater controller has blown 9 No power to pump receptacle on 1 Debris in impeller 2 Air trapped in housing 3 Rotor bearing worn 1 Heater not turning on 2 Heat indicator on no heat gain 3 Losing heat from pool Solution 1 Reset breaker 2 Turn disconnect to ON position 3 Verify wiring of controller 1 See above diagnosis 2 Plug in keypad cord Plug must l
9. Please refer to the Supplemental Guide for more informa tion on this option The Above Deck can be mounted at either the front or the back of the pool and is compatible with any of our coping options The Above Deck version comes with a convenient bench cover offered in a variety of colors to compliment any decor Please refer to the Supplemental Guide for more information on this option Optional Solar Blanket Roll Up System Endless Pools Inc supplies a Solar Blanket for all Endless Pool sizes if the Retractable Security Cover has not been chosen For those who wish it to serve as a permanent cover a simple PVC pipe may be used to roll up the blanket for storage when the pool is in use For this purpose we supply PVC clips and PVC pipe long enough for your pool width Depending on the width of the pool the PVC pipe will come in one or two pieces with a coupling attached to one end of the one piece of pipe Using the PVC cleaner and PVC cement you received in your plumbing kit glue the second piece of pipe into the open end of the coupling Alternatively the roller mechanism from the retractable security cover may be used in conjunction with a length of 3 diameter PVC pipe to roll up the blanket This optional solar blanket roll up system is available from the Endless Pools Inc Customer Service Department ENDLE SS POOLS 26 Optional UV Sanitizer Ultra violet water purifiers provide a chemical free method of maintaining your
10. Using a sta bilized chlorine source is more expensive and it also requires the periodic testing for cyanuric acid levels If the level gets too high it can render the chlorine ineffective and it may necessitate the partial draining of the pool in order to lower the levels Alternatives to Chlorine and Nature2 Although some alternative Sanitization systems can be used with an Endless Pool the following precautions must be followed e Under NO circumstances can salt chlorine generating systems be used in an Endless Pool e Bacquacil systems damage clear plastic products Light lenses and pump strainer lids will crack e Bromine can be used but not in conjunction with Nature2 e Please call Customer Service with any questions about alternate systems 3 Pool Equipment Start Up amp Operation The pool is full when the water level completely covers the hon eycomb grills where the current is produced A water level 1 2 or more lower than this can cause air to get pulled through the skimmer filter and into the WQS plumbing lines This can lead to problems with the filter and can also cause your heater to work intermittently A water level 1 or more higher than the top of the grills can lead to water getting splashed out of the pool ENDLE SS POOLS Once the pool is full and all connections are made the water qual ity system can be started Verify that the Nature 2 cartridge is in stalled inside the skimmer filter cartrid
11. calcium content and essentially lower the CH level inside the pool If softened water is unavailable perhaps water tanked in from an outside source would be the best option for you If this not possible either we would strongly suggest adding the sequestering agent sent with the pool This chemical helps the water hold all of its dissolved materials in solution including metals and calcium content The main concern with having CH levels too high is that the calcium may deposit out of solution a seques tering agent will help prevent this Calcium hardness will tend to slowly increase over time as water evap orates from the pool and leaves its calctum behind Periodic testing of CH is detailed in the Maintenance and Use of your Endless Pool instructions below 5 How to Swim in an Endless Pool Your swim current is operated via a remote control Two remote controls have been provided with your system and have been pack aged inside the power unit control box along with the antenna kit Upon initial start up you will find that unit has been set to its low est speed which is a barely perceptible current You will need to press and HOLD the FASTER button to increase the speed The swim current is turned on through the use of a remote con trol which also adjusts the speed of the current faster or slower When changing speed you must press and hold the buttons on the remote then wait a few seconds for the current to ad
12. into current pH increaser or pH decreaser to maintain levels between 7 4 7 8 Weekly Test for total alkalinity TA once a week Slug i e pour chemical in 4 spots around pool with water calm TA increaser or pH de creaser to maintain levels between 80 120 If TA is too high it is usually not necessary to decrease as it merely serves as a buffer for the pH and will not cause damage in the pool e Test for total chlorine TC once a week If the test for TC yields a result that is significantly higher than level of FC i e the solution gets noticeably more pink then you have a significant amount of combined chlorine CC in the pool water Combined chlorine gen erates a heavy chlorine odor and can cause bather discomfort in the form of eye and skin irritation If you have significantly more total chlorine than you do free chlorine then it is time to shock the pool ie add enough chlorine to get the FC between 3 5ppm but don t swim until FC falls below 3ppm Shocking the pool should burn off the combined chlorine Every two weeks e Test for calcium hardness CH once every two weeks Predissolve calcium hardness increaser i e fill a 5 gallon bucket with pool water and dissolve calcium in bucket then pour the solution into the current to keep levels between 175 250 ppm If CH is too high it can only be decreased by adding water with less calcium i e softened water If you have an outdoor pool or if you use sta
13. pool by destroying organic pollutants as the water passes through the treatment chamber This reduces the need for chemical sanitizers such as chlorine Our UV system is particularly suitable for users who are sensitive to the usual swimming pool dis infectants heavy metals from ionic purifiers or allergic to chlorine UV still needs to be used in conjunction with a sanitizer to burn off the dead organic matter killed by the UV system We recom mend simply using trace amounts 0 5 1 ppm of regular household bleach such as Clorox or other generic brands This level is lower than the EPA recommended chlorine level for drinking water 27 Optional Treadmill Manual or Hydraulically Driven Turn your Endless Pool into a complete home gym with the ad dition of an Aquatic Treadmill Use the treadmill with the current on or off to vary the intensity of your walk or jog Take it to the next step and use the aquatic treadmill to cross train in the Endless Pool Alternate between swimming and walking or jogging to get a full body workout Our new Aquatic Treadmills offer a spacious 20 wide belt for walking or running Both manual and hydraulically powered versions are available Our underwater treadmills are typically installed in pools with deeper panels 28 Optional Hydrotherapy Jets System By providing a supplementary pump that is operated by the heater controller and using the secondary suction and four venturi type jet
14. the hydrotherapy jet option and your pool is exposed to freezing conditions please refer to Hy drotherapy Jet Supplemental Guide for additional insulat ing measures 7 Liner Hanger The aluminum liner hanger installs around the perimeter of the pool panel enclosure The liner hangs from this ex trusion using a bead that is heat welded into the top edge of the liner The liner hanger system is packaged in the pool Self drilling fasteners are included in the kit along with a nut driver attachment for your drill Fig 7 Because the height of the 2 steel reinforcing channels is slightly higher than the surrounding top flange we provide PVC shims inside the kit to place under the liner hanger and to shim the hanger up to the level of the channels to keep the whole system level The shims can be cut with a hacksaw or scored with a utility knife and snapped to fit the size of the pool Over the channels the fasteners should be drilled through the channel and the flange You may use a pilot hole if you wish Elsewhere the fasteners must be drilled through the shims and the panel flange Take the four 8 lengths of liner hanger that have been notched in the center and bend these pieces so that they will fit and be secured in each corner Measure to ensure the corner piece is centered in the corner Use two self drilling fasteners and PVC shims to secure the small corner length first by drilling through the back corner of the liner hange
15. the panel then they have to be installed at this time as well Use a sharp utility knife to cut a round hole in the liner using the hole in the panel as a template Install the suction thru wall fitting as shown in Fig 16 Repeat this process for the remaining jet suction fitting The plumbing between the suction fittings and the jet pump should be completed prior to starting to fill again as detailed in the Jet Supplemental Guide Once this is completed close the ball valve This will allow you to continue filling the pool without having to plug the suction fittings from inside the pool Once this is completed proceed to the next section 12 Swim Current Component Assembly Provided with this Installation and User s Manual will be the appropriate Supplemental Guide for the type of Swim Current that has been purchased This guide will take you through the assembly of the pri mary internal components of the pool Additional Supple mental Guides will be provided and will have to be referenced should any optional internal components eg hydraulic treadmill corner steps bench seats etc have been purchased 13 Thru Wall Connections Part 2 Once the water level is three inches below the next lowest thru wall above the benches stop filling the pool so that the remaining holes in the liner can be cut At a minimum there are four holes to be cut the Water Quality System suction amp return and the Swim Current high
16. the two swim current thru walls The high pressure hose is to be inserted into the higher fitting Install the Water Quality System pre plumbed thru wall assemblies as shown in Fig 19 Make sure to secure one of the insert elbows into the Water Quality Suction fitting The elbow must be facing down and away from the propul sion housing Fig 20 Optional Underwater LED Lights If the optional underwater LED lights have been pur chased then the lens barrel should be installed at this time as well Use a sharp utility knife to cut a round in the liner using the hole in the panel as a template Install the lens barrel as shown in Fig 21 Optional Hydrotherapy Jets If the jet suction holes in the panel have been cut the panel in the Alternate position above the benches then install that fitting at this time Use a sharp utility knife to cut a round in the liner using the hole in the panel as a template Install the thru wall fitting as shown in Fig 16 The plumbing between the suction fittings and the jet pump should be completed prior to starting to fill again as detailed in the Jet Supplemental Guide Once this is com pleted close the ball valve This will allow you to continue filling the pool without having to plug the suction fittings from inside the pool The four jet fittings can now be installed as well Use a sharp utility knife to cut a round in the liner using the hole in the panel as a template In
17. vacuum running smooth out all of the wrinkles When you are sat isfied with the placement of the liner start to fill with water Keep the vacuum running until there is about 6 of water in the shallowest portion of the pool Turn the vacuum off and remove all tape and the vacuum hose Do not fill be e yond 6 at this time Included in the box with the liner are No Diving signs Please post these in prominent locations around the pool The Endless Pool is shallow and must never be used for diving Diving into the pool is a very serious hazard and these stickers are intended to warn children of the risks Naturally adult supervision is also critical whenever chil dren use the pool ENDLE SS POOLS 1 Thru Wall Connections Part This step only should only be followed if the Optional Hydraulic Treadmill or Optional Hydrotherapy Jets is being installed Otherwise proceed to the next section Hydraulic Treadmill If you are installing a hydraulic treadmill then the thru wall fittings for that option will have to be installed at this time Use a sharp utility knife to cut a round hole in the liner using the hole in the panel as a template Install the thru wall fitting as shown in Fig 15 Proceed to next section Hydrotherapy Jets If you have purchased the hydrotherapy jet option and you have cut the holes in the panel for the jet suction in the Tdeal location 10 up from base of
18. INSTALLATION OPERATIONS AND USER S MANUAL Fully In Ground Installations Original Endless Pool ef a bs d s es Sech ota E am ng see Ee fig ree m a Se Bees ZZ E e a AA ENDLESS POOLS SWIMMING MACHINES Installation Instruction Booklet Information The entire Endless Pool system is ETL listed Ref 2001779 and conforms to UL Standard 1563 Individually all electrical com ponents of the Endless Pool are UL and or CSA approved As defined by the International Residential Code IRC the Endless Pool is considered an aboveground or an in ground pool depending on the installation That is to say customers can install our End less Pool Kit above ground on a garage or basement floor or in the backyard or they can sink it partially or fully in ground The unit is completely self supporting As required by the IRC the Endless Pool meets all the following standards ANSI NSPI Standards 3 Permanently Installed Residential Spas 4 Aboveground On ground Residential Swimming Pools 5 Residential In ground Swimming Pools and 6 Portable Spas The appropriate governing standard is dependent on the installation method and the re quirements and definitions used by the local governing bodies All electrical connections should be made by a licensed electrician in accordance with the current national and local electrical codes All pool equipment including the 4 kW electric heater circulating pu
19. Li J 4 20 ma our CIRC SAVER IN f n J 4 20 ma com CIRC SAVER Bees l 24 COM LINE ONE IN ANTENNA on side Ground Line 2 Neutral Line 1 Wiring Schematic for 60hz Power Unit 230v 24 amp single phase 24 VDC LINE TWO IN NEUTR SWITCHED OUT l SOL l SOL SWITCHED IN l BONDING LUG A onse s N Q LINE IN HYDRAULIC POWER UNIT connection on side Hydraulic Power Unit 5 HP 21 FLA Amps 230 VAC 60 Hz HEATER CONTROLLER optional 24 Amps 230 VAC 60 Hz O PROPORTIONAL K O K O for FLOAT RELIEF VALVE DISPLAY LEVEL Wiring Schematic for 60hz Heater Controller HEATER CONTROLLER Gecko in xe Electrical Wiring Connections 50hz Wiring Schematic for 50hz Power Unit 220v 30 amp single phase RADIO REMOTE CONTROL Va l 4 20 mA OUT CIRC SAVER IN ll f l 4 20 mA COM CIRC SAVER Radio 24 com EEN HYDRAULIC POWER UNIT Antenna LINE TWO IN NEUTRAL SWITCHED OUT SWITCHED IN optional REMOTE DISPLAY 5 HP electric motor 1 phase 230 VAC 21 AMPS Hydraulic Power Unit HPU Brown Blue Gi Green Yellow 230 VOLT Single Phase Type C Motor Rated 30 Amp RCD Wiring Schematic for 50hz Heater Controller Neutral Brown Blue Gd Green Yellow HEATER CONTROLLER Gecko in xe ENDLESS POOLS 20 Bonding and Grounding All of the electrical equipment that we supply is UL or C
20. SA ap proved and must be installed in accordance with local electric codes by a licensed local electrician Bonding and Grounding is an important part of that process All electrical components have bonding lugs and should be bonded together and to the steel pool panels A bonding conductor shall be solid copper not smaller than 8 AWG and may be insulated covered or bare If new construction is involved where reinforcing rods are installed in the concrete under or adjacent to the pool this should be in cluded in the bonding circuit Each of the pieces of equipment should be separately grounded A 8AWG bare copper wire and bonding kit will be provided in the hydraulic hose electrical whip box This wire will be the same length as your electrical whip Connect this wire to your power unit and run it with your hydraulic hose and whip to the front of the pool Inside the bonding kit there will be a machine screw and nut a bonding lug and a drill bit Attach the bonding lug to the Z brace just under the heater controller Feed the bonding wire through the bonding lug on the Z brace through the opening in the heater controller mounting board and con nect it to the bonding bar on the heater controller Jet Pump Fuse Unused Fuse Circulation Pump and UV Fuse Transformer Fuse ENDLESS POOLS 21 Heater Controller Plug In Connections The Heater Controller In xe features in links connectors with colored and tagged polarizers Th
21. amp low pres sure hydraulic lines Note if you are installing an Elite or Dual Propulsion Endless Pool then there will be two sets total of 4 hydaulic lines Use a sharp utility knife to cut a round in the liner using the hole in the panel as a template Install the thru wall fitting as shown in Fig 18 Cork Gasket Lock Nut Rubber Gasket Rubber Gasket wN Thru Wall Fitting Fool Panel J Fool Liner Fig l 5 Rubber Gasket Pool Panel Lock Nut Pool Liner A VGB Approved Suction Cover Suction cover must be screwed to fitting prior to installing Jet Suction Fitting i N Cork Gasket Rubber Gasket Swim Current High Pressure Fit Swim Current Low Pressure Fitt Water Quality System Return Fitting Water Quality System Suction Fitting Fig 17 Rubber Gasket Cork Caeket Rubber Gasket Lock Nut _ Thru Wall Fitting Fool Fanel Fig 18 Fool Liner Pre plumbed thru wall assemblies High Pressure Hose Low Pressure Hose Red tape wrapped around the fitting Attach insert elbow to the suction thru wall prior to securing to the pool wall Fig 20 Pool Panel Clear Gasket Light Lens Lens Locknut Pool Panel Pool Liner Jet Bulkhead WW ENDLESS POOLS The hose with the red tape wrapped around the fitting is the low pressure hose and should inserted into the lower of
22. annels in the same fashion as the regular liner hanger sys tem The installer is responsible for building a proper perime ter substrate for the concrete or tile Fig 9 AN H AW Mir BULLNOSE RECEIVER COPING WITH INTEGRAL LINER HANGER SILICONE SEALANT AROUND PERIMETER OF COPING BY OTHERS Optional Wood Receiver Coping System Typically used when the pool is installed fully in ground the Optional Wood Receiver Coping System allows the installer ee laut to finish with wood or synthetic decking right up to the water s edge The aluminum Wood Receiver Coping System acts as both a liner hanger and a finished edge which can easily accept 2 wood coping Endless Pools Inc supplies precut pieces to fit the specific pool size ordered Included in the kit are mitered corners and straight pieces to provide a ENDLESS POOLS T Z 258 MIL PVC LINER Fig 9 finished look These extrusions are fastened down to the top flange of the pool panels through the PVC shims and the re SILICONE SEALANT A e A AROUND PERIMETER inforcing channels in the same fashion as the regular liner l OF COPING BY DN hanger system The installer is responsible for building a OTHERS proper perimeter substrate for the decking material Fig 10 e a s WOOD TILE RECEIVER Optional Aluminum Coping System COPING WITH INTEGRAL The Endless Pools Aluminum Coping Option offers a con ER venient method to finish off the top
23. artridge BRE et ee eo oe i coca Pad Ler see Fig 51 Fig 51 ae 2 G E See eme gt a DR s ao ae j ee a a ege a KE s TE j Fig 51 ENDLESS POOLS Every two months Remove and clean the filter that is located inside your pool at tached to the propulsion housing First turn the Water Quality System off by pressing and holding the 1 Key see section Key pad Functions until the display reads OFF Then remove the cylindrical filter cage from the filter body Grab the filter inside and unthread it from the filter body Once out the filter can be cleaned by simply rinsing it off or by using a filter specific de tergent If your filter is being cleaned with a detergent then re move the Nature 2 from the cartridge Insert the cleaned filter back into the filter body and thread into place Reinstall the fil ter cage over the cartridge The circulation pump will automat ically turn back on after 30 minutes After several uses the cartridges will have to be replaced Re placement cartridges can be purchased on our Customer Service website www myendlesspool com 4 Balancing the Pool Water Test your pool water now with the kit provided and or take a sam ple of water to a local pool professional for testing The test kit provided by Endless Pools tests for chlorine pH total alkalinity calcium hardness and cyanuric acid While the test kit may first
24. as shut the heater down because the temperature at the heater has reached 119 F 48 C Do not enter the water Remove the spa cover and allow the water to cool down then shut power off and power your spa up again to reset the system AOH Temperature inside the spa skirt is too high causing the internal temperature in the in xe to increase above normal limits Open skirt and wait until error clears FLO The system does not detect any water flow while the primary pump is run ning Check and open water valves Check for water level Clean filter If the problem persists call Customer Service Prr A problem is detected with the tem perature probe Call Customer Service OH The water temperature in the spa has reached 108 F 42 C Do not enter the water Remove the spa cover and allow the water to cool down to a lower temperature Call Customer Service if problem persists UPL No low level configuration software has been installed into the system Call Customer Service 28 ENDLESS POOL LIMITED WARRANTY FITNESS MACHINES LLC WARRANTS TO THE ORIGINAL PURCHASER OF THE ENDLESS POOL MANUFACTURED BY US TO BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP UNDER NORMAL USE FOR TWO YEARS FROM PURCHASE Our obligation under the warranty shall be limited to the repair or exchange at our option of any part or parts which may thus prove defective under normal use within two years from date of purchase by the original p
25. ater will be dropped out of solution and on to the benches and liner Having the pH too high or too low may cause bather discomfort in the form of eye or skin ir ritation The pH will change slowly over the course of a week or two The number of bathers and the type of chlorine used are just two factors that will cause the pH to change For this reason pH should be tested three times a week and adjusted as needed See the Maintenance and Use of your Endless Pool instructions found later in this guide for further details Once the pH is within range move on to adjusting the calcium hard ness 3 Balance Calcium Hardness CH Ideal reading 180ppm Acceptable range 175 250ppm Raise with calcium chloride calcium hardness increaser Lower with water containing less calcium softened water 24 Method of chemical application Fill a clean five gallon bucket with pool water and dissolve the dosage of calcium into this water Do not mix this solution with your hands Pour the solution in to the swim current and let the current circulate the water in the pool for a few minutes Wait a few hours test again and add more calcium if necessary Once again always add less chemical than you think will be necessary to effect the desired change Notes As with TA many regions will have higher CH than what is specified by our recommended range If it is available partially filling the pool with softened water will dilute the
26. ating the pool while pre venting evaporation Consistent use of this cover will keep the water cleaner save energy and help control humidity The cover should be completely removed from the water before the machine is used With standard width Endless Pools 7 inside dimension the cover is shipped in a box with clips along with a 1 1 4 PVC pipe Replacement covers are available from our Customer Service Department The cover once cut to size and installed on the PVC pipe rolls out onto the water surface Nature 2 Installation The Nature 2 purification system will be placed inside of the filter cartridge A retention strap has been provided to prevent the Na ture 2 slotted yellow cartridge from falling out of the filter Remove the Nature 2 and retention strap from its packaging Pass the strap through the Nature 2 so that the locking mecha nism of the strap is facing up 23 Loop the strap over onto itself and interlock the strap end into its locking mechanism The strap end should be inserted into the locking mechanism no more than 4 5 positions Next pull the cylindrical floating cage out of the filter body Re move the filter cartridge from the filter body inside the pool by grabbing the top and unthreading the cartridge Insert the Nature 2 into the opening in the bottom of the car tridge so that the retention strap is facing down Reinstall the filter cartridge and then place the floating skimmer cage over top the c
27. bilized chlorine i e sodium dichlor or sodium trichlor test the cyanuric acid CYA level every two weeks Maintain levels between 20 50 ppm If CYA is above 80 ppm the pool should be partially drained and refilled or un stabilized chlorine should be temporarily used in place of the stabilized If CYA is above 100ppm the pool should be partially drained and refilled ENDLESS POOL Sr Every two months e Remove and clean the filter that is located inside your pool at tached to the propulsion housing First turn the Water Qual ity System off by pressing and holding the 1 Key see section Keypad Functions until the display reads OFF Then re move the cylindrical filter cage from the filter body Grab the filter inside and unthread it from the filter body Once out the filter can be cleaned by simply rinsing it off or by using a fil ter specific detergent If your filter is being cleaned with a de tergent then remove the Nature 2 from the cartridge Insert the cleaned filter back into the filter body and thread into place Reinstall the filter cage over the cartridge The circulation pump will automatically turn back on after 30 minutes e After several uses the cartridges will have to be replaced Re placement cartridges can be purchased on our Customer Serv ice website www myendlesspool com Every four months e Remove the Nature2 cartridge located in your skimmer filter dis card and install a new one Because th
28. creaser 1 Container vinyl cleaner 1 Pool patch kit wet 1 Container stabilized chlorine outdoor pools 1 Nature 2 cartridge 1 Spa Wand 1 Test kit Overview The Endless Pool is a combination of several independent sys tems The swim current system is comprised of a 16 propeller that rotates at variable speeds and is adjusted by remote control The operation of the swim current system is described later in this start up section A second system maintains the water quality by circulating filtering heating and purifying the water This Water Quality System WQS is comprised of the pump filter Nature 2 purifiers and heater The Hydrotherapy jets and a supplemen tary pump comprise a third system Endless Pools will provide toll free technical support during the installation and start up of your swimming machine We encour age you to become familiar with the equipment and components in order to properly maintain the pool 2 Filling Your Endless Pool Your Pool Water As with any swimming pool an Endless Pool requires water chemistry monitoring The water quality system which includes automated recirculating heating filtration and purification does most of the work for you However balancing and maintaining your pool water is essential to the life and health of your equip ment Your Source of Water Endless Pools Inc recommends testing a sample of water before you begin to fill the pool
29. d the green wire to the G terminal 19 Electrical Wiring Connections 50hz The following is for the U K and countries with a similar power supply Two 220 volt 30 amp RCD circuits are required to operate the Endless Pool A minimum of 10AWG wire should be used for all field wiring All connections should be made by a licensed electrician We recommend that you have your electrician install one shut off within 5 of the location of your hydraulic power unit and another shut off to accommodate the heater controller installed on the front panel You can have your electrician install this prior to your pool being delivered Please consult all appropriate national and local codes Power is supplied to the hydraulic system by connecting the existing whip on the hydraulic power unit control box to the shut off in stalled by your electrician Power to the poolside heater controller is supplied by connecting the second shut off and the heater controller through the appropriate knockouts in these respective units This must be hard wired Once the Water Quality System has been installed and your electrician has completed the wiring you should install the Water Quality System Cover Place the cover over the entire water quality system Use the screws provided to attach the cover to the mounting plate ENDLESS POOLS Electrical Wiring Connections 60hz ENDLESS POOLS optional REMOTE DISPLAY connection N RADIO REMOTE CONTROL
30. d to use by adding silver and copper to the pool which will kill bacteria and algae in the water This cartridge should be replaced about every four months Oxidation and Chlorine Requirements Nature2 works well as a pool sanitizer however it does not oxidize or burn up small particles of debris in the pool Maintaining a minimum level of 0 5 ppm free chlorine in your pool at all times is necessary Adding 1 2 cup of Clorox a day will add about 0 5 ppm of free chlorine to a standard sized pool How quickly that chlorine is consumed depends upon water temperature bather load and the amount of direct sunlight the pool receives Chlorine Stabilizer and Outdoor Pools Your Taylor test kit comes equipped with testing procedures for cyanuric acid Cyanuric acid is a chlorine stabilizer meaning it protects chlorine from getting broken down by sunlight If your pool is located outdoors we recommend using the granular form of stabilized chlorine Should have an active ingredient of sodium dichlor instead of Clorox Another option would be to supple ment Clorox by adding cyanuric acid Either method will neces sitate testing for cyanuric acid every two weeks These chemicals are readily available at any pool supply store Chlorine Stabilizer and Indoor Pools Many customers are sold a stabilized chlorine product for use in their indoor Endless Pool Endless Pools would not recommend this practice as Clorox bleach is ideal for this setting
31. dard depth portion of the pool i e the water is half way up the benches Do not drain further than this as the liner needs this much water in order to be held stretched out and in place If you are leaving the water like this for an extended period of time add chlorine and possibly an algaecide in order to mini mize the clean up required before refilling the pool 5 When you are ready refill the pool using a garden hose with a bobby filter on the end to screen out debris and fine sediment If you do not have one of these filters contact Endless Pools Customer Service If you have high calcium content and or high metal content in you area you should also add some se questering agent to the pool water to help prevent scaling staining You may also be able to find both of these items at a local pool store 6 When the water has risen to the top of the benches reinstall the four corner covers Be careful not to push the covers against the liner or hit the liner with the edges of the corner covers Doing so may cause a leak 7 The pool is full when the water completely covers the grill at the front of the pool Reestablish electrical power to the pool equipment and start balancing the pool water Shock the pool to 3 0 ppm free chlorine Turn on your WQS in order to get your new body of water filtered circulated and heated 8 Winterizing Your Endless Pool An Endless Pool may be used year round even in colder climates
32. e any rain water that may accumulate The most popular configuration for this system is to have the cover roll off the rear of the pool Other alternatives are possible if space is limited These are discussed in more detail in the Sup plemental Guide The kit includes the roller mechanism for the width of pool purchased appropriate lengths of track an alu minum leading edge and the rugged fabric which floats on the water surface suspended between the parallel tracks Two steel brackets to mount the roller mechanism at one end of the pool are available The optional Retractable Security Cover system is manually pow ered We believe that this system is optimal for our compact pool and when installed correctly provides a simple means of covering the pool The aluminum track on either side of the pool is a requirement of the retractable security cover option Covering this track is possible but increases complexity and will add to the cost of installation Optional Automatic Retractable Security Cover System Offered in two versions the Automatic Retractable Security Cover System is rapidly becoming one of our most popular options Op erated with the turn of the key the cover retracts easily making it ideal for people who want the convenience of automation or lack the strength to operate one manually The Below Deck version can be fully integrated into any custom finish The cover mechanism must be mounted at the front of the pool
33. e simple pipe insulation and clips for this purpose See Figure 45 on page 20 24 Optional Antenna Extension Your swim current remote operates by radio waves Should the power unit be placed far away from your pool the re mote control may not operate efficiently In order to correct this you should install the Antenna Extension Kit If your antenna has already been installed disconnect it from the side of control box Install the antenna extension wire finger tight onto the control box connection Once the antenna has been positioned closer to the pool connect the other end of the extension wire to the antenna Should you need a longer wire than what was provided you can pur chase coaxial cable locally 1 Tabs of Isolation cover will nest into the slots of the Mounting Board Secure Isolation Cover to the Mounitng Board with the provided 1 2 Screws ENDLE SS POOLS 25 Optional Retractable Security Cover Systems Our most popular option and strongly recommended the Re tractable Security Cover system protects children and pets from the pool while keeping in temperature and humidity With some installations suitable access for this roll up cover system is com plex and should be discussed with an Endless Pool design profes sional during the planning stage The Supplemental Guide describes the cover installation more fully If your pool is to be outside we can provide you with a cover pump to remov
34. e vermiculite will be used to level the floor filling in Liner Underlayment voids or covering bumps The plastic floor will be cut to fit 1 8 plastic sheets cut to fit if floor and placed over the vermiculite and will be taped to them leveling kit was purchased or closed cell selves and to the base of the panels foam cut to fit if anchor bolt kit was chosen Y SS SSS ENDLESS POOLS Do not attach foam to the steel walls of the pool Secure the foam inserts in the 4 corners at the bottom Foam cor ners are not installed in the 4 corners of the deeper section of a custom deep end pool Fig 12 Standard flat bottom pool liners are usually packaged in a cardboard box in the pool crate Liners for deeper pools and Wy custom sized pools are sent separately by UPS Ground Check to see if your liner was backordered at the time of shipment If you have any questions call Customer Service Seal the liner hanger panel seams and where the panels meet the floor with silicone about the status of your liner All work around your pool should be completed before you Ge install your liner Take a moment to be sure you have all Feed the vacuum necessary work completed Prepare for the liner installation Ge Ee Be sure that the liner hanger corners panel joints and panel SE eeh SC face GER e panel to base material are sealed with silicone Tape off all holes deg tape in the pool wall lights jets and front panel holes from t
35. edge of your Endless Pool either indoors or out The coping which also acts as a liner hanger is 1 3 8 thick and comes in a sand textured white fin ish The pieces are precut to fit your pool size and fit securely over the steel channel The coping system is delivered with your pool It may be ordered later and shipped by UPS ground for Awana an additional shipping charge The kit s weight depends on the POOL PANEL pool size and comes in 5 boxes Fig 11 28 MIL PVC LINER Each coping kit contains pre fabricated corners and straight aluminum pieces cut to match your pool size These corners are either square or mitered based on your order The 8 wide profile of the coping makes it ideally suited for pools that are freestanding or partially recessed The coping is secured to the top of the wall panel with tek screws which are concealed ALUMINUM beneath the aluminum snap strip of the same finish as the SE coping As an alternative the 6 3 8 snap strip can be elimi l T f E nated and a 6 accent tile can be installed Joints between the oo J aL Cel INTEGRAL LINER adjacent coping pieces are covered with an aluminum cover ae deiere 1 Ka Fig 10 The front panel will need to be extended or packed out with customer supplied finished materials to extend beyond the equipment mounted on the front panel See Technical Spec ification for details strip with the same finish as the coping ok TOP FLANGE OF GALVANIZED STEEL
36. er controller union nut The raise section of the T gasket will sit in the groove of the tailpiece Once the heater controller is securely attached to the plumbing makes sure that it is level Use the provided self drilling screws to attach the mounting board to the Z brace panel stiffener Use a minimum of 2 screws When the mounting board hits more than one Z brace attach with two screws along the top In the instances when it lands on only one Z brace attach with one screw along the top and one screw through the bottom slotted tab as shown in Figure 26 A mimimum of 2 screws should be used to attach assembly to the panel Z Brace At the outlet of the heater controller attach the single heater controller tailpiece Again make sure the T gasket Heater Controller is seated properly prior to tightening the heater controller Tailpiece union nut Fig 27 T Gasket Attach the pre plumbed return assembly to the Water Quality System thru wall Make sure to wrap Teflon tape around the threads of the adapter that is glued into the thru wall The union of the pre plumbed return can be 1 1 4 the depth of the taken apart to make this step easier tailpiece socket Take a measurement from the edge of the heater controller tailpiece to the vertical pipe of the pre plumbed return as sembly Add 1 1 4 to that dimension the 1 1 4 is the depth of the tailpiece socket Transfer this total dimension
37. ge When power is first introduced to the system the heater con troller will go through a boot up cycle which can last 2 5 min utes During this boot up cycle it is important that no buttons on the keypad are pushed At the end of the boot up cycle the keypad should display the temperature of the water If the keypad is flashing FLO then air may need to be bled out of the system Turn the power off and slowly unthread one of the pump unions allowing any air to escape the system When bleeding the system you will loose some water so it is important to take this into account Once the air has been bled out retighten the union After the system is turned on and the heater controller has veri fied proper water flow to avoid heater activation in dry condi tions the heater will automatically turn on to reach and maintain the water temperature set point Your heater controller has been programmed to run your circu lating pump continuously meaning that your pool is receiving au tomated circulation and filtration through the skimmer filter 24 hours a day The temperature of your pool is controlled by the up and down keys on your keypad Refer to the following section for more information on the heater controller features The Heater Controller has a freeze protection feature called Smart Winter Mode Smart Winder Mode senses the ambient temper ature around the heater controller and turns on the optional hy drotherapy jet pu
38. gen e d en anaana 21 Water Quality System 244 E SE E NEEN a ee H Optional Interior Stair EE 21 Skimmer Filter Installation 11 Optional Swim Mo 21 Keypad Installation NEE 14 Optional Synthetic Coping System 21 Power Be EE 14 Endless Pool Warranty 2 2440354400 0edeatesee end e as 29 OVETVIEW e E oiera rekat atra atas 21 Maintenance and Use of Your Endless Pool 25 Filling Your Endless Pool 21 Draining Your Endless Pool 26 Pool Equipment and Startup 05 22 Winterizing Your Endless Pool 26 Balancing the Pool Water 24 Poolside Water Quality System Troubleshooting 21 How to Swim in an Endless Pool 25 Keypad Functions and Troubleshooting 28 ENDLE SS POOLS Pool Arrival and Inspection The Standard Endless Pool arrives in three packages a skid of pool panels weighing approximately 850 lbs a 4 x 8 x 4 high crate weighing about 1 150 lbs and a pair of 6 5 8 wide steel re inforcing channels Most shipping companies will lower the con tainers to the ground with a hydraulic lift gate on their truck The pool can remain in the containers until you are ready to begin in stallation Please contact our shipping department prior to ship ment to answer any questions you may have Since every delivery is slightly different and depends to a large extent on site condi tions it is important to speak with our shipp
39. hat involves adding a measured amount of chlorine either after you swim or at the very least every other day This measured amount depends on pool use One person swimming every day for 30 minutes might add 1 2 cup of Clorox after each swim This small amount should maintain the required 0 5 to 1 5 ppm chlorine residual Heavier use and use by children generally requires more chlo rine Adding 1 cup of Clorox bleach to a standard sized Endless Pool raises the chlorine level by about 1 ppm It is safe to swim in any pool where the chlorine level is between 0 5 to 3 0 ppm free chlorine Recommended Maintenance Schedule Daily e Test for free chlorine FC after you swim or at least a few times a week Add chlorine to maintain FC levels between 0 5 1 5 ppm As you become familiar with the chlorine demand for your pool you will find that you may not have to test for chlorine as frequently in order to maintain a minimum level of 0 5ppm Twice a week e Check and adjust water level Water should completely cover the honeycomb grill where the current is produced Water 1 2 lower than this can create a choppy current and may cause your skimmer to draw air into the plumbing lines Having the water level 1 or more higher that honey comb grill will cause more water to get splashed out of the pool and may cause the air relief port on the top of the skimmer body to leak water Test for pH at least twice a week Broadcast i e pour chemical
40. he from the outside outside Place a vacuum hose through the highest thru wall cutout or leave a small section of liner bead out of the liner hanger and insert the vacuum hose down from the top 4 Make sure that the vacuum hose opening is sealed with duct eae e tape The hose should be 3 4 off of the bottom of the of the vac hose is j pool floor foam Fig 13 at least 5 off of the floor Fig 13 Install the liner by starting at the center of the front panel Spread the liner in the pool enclosure Shoes should be re moved for this and all future work in the pool to avoid dam aging the liner Find the vertical seam in the liner and center it at the front of the pool Place the four bottom corners of the liner in the four corners of the pool While standing in one corner fit the top bead of the liner into the slot in the liner hanger For easiest install fit the liner bead at both Vertical Seamer corners of an end of the pool then fit the other two corners liner centered at the opposite end Work your way around the pool fitting on the front panel the bead evenly into the hanger We recommend not ending in a corner Smooth the liner on the floor pushing any wrinkles toward the walls Fig 14 After verifying that the vacuum hose is off of the bottom turn the vacuum on When the liner is drawn back check to see that the corners are positioned properly If not turn the vacuum off and reposition the liner With the
41. hz The following is for the U S and countries with a similar power supply One 220 volt 30 amp GFCI circuit is all that is required to operate the Endless Pool A minimum of 10AWG wire should be used for all field wiring All connections should be made by a licensed electrician An electrical whip to connect the power unit to the heater controller is provided The length of this whip is based on the length of your hydraulic hose specified in your order We recommend that you have your electrician install a shut off within 5 of where you intend to place your power unit You can have your electrician install this prior to your pool being delivered Power is supplied to the system by connecting the existing whip on the power unit control box to the shut off installed by your elec trician Power the poolside heater controller by connecting the whip supplied to both the power unit control box and the heater controller through the appropriate knockouts in these respective units Specifically inside the power unit control box connect the black wire to terminal R2 on the line left side of the contactor connect the red wire to R3 on the load right side of the contactor connect the green wire to the ground bus bar and the white wire junctions with the white wire coming from the shut off using a wire nut Connect the heater controller by attaching the black wire to the L1 terminal the red wire to the L2 terminal the white wire to the N terminal an
42. ing department well in advance to reduce the chance of surprises Upon arrival the packages should be inspected for external dam age Should there be visible damage you must complete a dam age claim report provided by the truck driver Please call the Endless Pools shipping department immediately at 800 732 8660 The pool components are not damaged by freezing condi tions and may be stored outside under a tarp for an extended period prior to installation To begin installation or to move pool components begin un packing the pool Using a hacksaw or tin snips remove the steel packing straps encircling the pool panel skid The wooden top and sides of the crate may be removed with a phillips head screwdriver 2 Site Preparation It is important that your Endless Pool be installed over a smooth level concrete slab that is capable of supporting 260 pounds per square foot The thickness and the quality of the con crete slab will affect the anchoring method If you are using the anchor bolt kit or you are installing a Custom Deeper Pool then the floor must contain no voids or bumps and shall be relatively smooth and level For custom deeper pools the walls of the deeper section must also contain no voids or bumps The corners at the depth change should be eased slightly approx 1 4 Custom deeper pools must use the Anchor Bolt Kit Anchoring the pool is discussed in more detail later in these instructions as well as in a Sup
43. is needs to be done every four months it is best to coordinate this around the cleaning of your filter cartridges see Every two months above New Nature2 cartridges can be purchased on our customer website www myendlespool com Every five years e After five years of operation we will send you a letter detailing our recommendation that the submerged hydraulic motor be changed This procedure does require the pool to be drained to 6 in the stan dard depth section of the pool This may also be a convenient time to replace the propeller or front grill in the pool a list of recom mended and optional replacement parts is supplied with the tune up letter As Needed e Clean the water line around the perimeter of the pool and the un derside of the cover as needed Body oils and mold may build up slowly in these areas and should be cleaned off periodically e The spa wand we provided with your pool can be used to help re move any debris that has settled on the floor of the pool floor If you have an outdoor pool you may need to remove front grill from where the swim current is generated with a Phillips head screw driver and clean as necessary Replace grill before restarting ma chine The Endless Pool must not be operated with this front grill removed If you happen to get cloudy water or if the liner feels slippery it likely means that you have algae in the pool A vinyl liner pool brush and pole may be purchased in orde
44. is plug and connector technol ogy has been specifically designed for easy and safe assembly The tags are interchangeable depending on the output the po larizers are designed to avoid misconnections In link connectors are easily and conveniently accessible from the front of the Heater Controller offering a wide range of pos sible connection configurations In link connectors come in 3 sizes HC LC and low voltage for all types of inputs and output devices They all include an integrated latch that keeps them safely in place and provides audible and tactile feedback when properly connected Finally colored and tagged polarizers provide a definite advan tage in easily configuring output devices Refer to Figure 41 for specific connections for the provided equipment Unused Connection Circulating Pump UV Connection Connection Jet Pump Connection Unused Connection Keypad Connection Lights Connection 22 Water Quality System Isolation Cover Now that the Water Quality System has been installed and your electrician has completed the wiring you should install the Water Quality System Cover Place the cover over the entire water quality system Use the provided 1 2 screws to attach the isolation cover to the heater controller mounting board Fig 42 23 Hydraulic Hose Connections Install the long hydraulic hoses between the Power Unit and hydraulic hoses at the front of the pool These hoses are sup
45. just Our standard pool s top speed is roughly equivalent to a 1 08 100 yard pace a speed for expert swimmers only Set the water speed at a comfortable level for your needs Remember since you dont have to turn in an Endless Pool your workout is continuous and you will tire faster than when swimming laps in a traditional pool To stop swimming simply press the on off button on the remote If left running the power unit will turn off automatically after thirty minutes and can be restarted by pressing the on off button again Once you have found an optimal speed for yourself you may leave the system at that setting The controller for the swim machine is designed with a ramp up feature which forces the swim machine to start slowly but will increase to the last setting at which someone swam When you are first learning to swim in the swim current it is often useful to allow yourself to drift back to the rear of the pool Let your feet rest on the rear bench and then swim forward into po sition By starting from the back you can get a feel for just how much room you have When swimming center your outstretched arm about one foot from the front grill 25 6 Maintenance and Use of Your Endless Pool Your Nature2 copper silver purification system will help disinfect the water but it will not keep the pool clean and clear by itself Nature2 is designed to be used in conjunction with chlorine We recommend getting into a routine t
46. l not significantly affect the following tests and proce dures used to balance the pool water Therefore if there is no chlo rine in the pool at this time add some Add 1 2 cups of liquid bleach any brand is fine as long as it does not have an added scent to it to an indoor pool If you have an outdoor pool add the ap propriate amount of granules out of the bag of stabilized chlo rine Test for chlorine in a day or two and add more if necessary 1 Balance Total Alkalinity TA Ideal reading 100ppm Acceptable range 80 120ppm Raise with Sodium Bicarbonate TA increaser Lower with Sodium Bisulfate pH decreaser ENDLESS POOLS Method of chemical application e level of TA in the pool requires that the chemica e slugged i e pour chemical in four different spots around the pool with the water calm Let the water remain calm until the next filtration cycle e Retest TA and adjust again if necessary e Add less chemical than you think is necessary to effect the desired change Keep track of how much chemical it took to make that change Notes Many regions of the country and world will have water with a TA higher than our recommended range In a lot of cases it will be de sirable to leave the TA alone as any adjustment to it will also tend to affect the pH The TA is mainly serving as a buffer for the pH If it is above 120ppm but lower than 200 250ppm leave the level alone It will simply over stabi
47. lize the pH which is not a problem especially if the pH is within range or close to being within range If the TA is lower than our recommended range though we would recommend increasing it to at least 80ppm Once again the TA serves mainly as a buffer for the pH and if the TA is too low the pH level in the pool can change very rapidly causing bather discomfort and damage to the pool and pool equipment Once the TA is within a tolerable range move on to adjusting the pH in the pool You should find that the TA will be slow to change for this reason test for it once a week as detailed in the Maintenance and Use of your Endless Pool instructions found later in this guide 2 Balance pH Ideal reading 7 5 Acceptable range 7 4 7 8 Raise with sodium carbonate pH increaser Lower with sodium bisulfate pH decreaser Method of chemical application e Measure out and pour your dosage of chemical directly into the swim current Afterwards make sure you wash some water on the propulsion housing to ensure that no granules are resting on the benches Test and apply more chemical as necessary Notes It is very important to keep the pH within range If the level is too low severe damage can occur to the pool liner and the submerged hy draulic motor and the pool equipment If the level is too high dam age can occur to the liner and it can make the water prone to scaling when minerals and metals dissolved in the w
48. ll risk and liability whatsoever resulting from the use thereof In order to claim this warrant original purchaser must promptly notify our Customer Service Department in writing of the existence of the claim and then follow our written instructions regarding the procedures for remedying the defect Endless Pools shall not be responsible for cartage transportation removal and or reinstallation labor or any other such costs relating to performance of the warranty In the event any portion of this warranty shall be deemed unenforceable by a court of law the remainder of this warranty shall remain in full force and effect as if the voided portion were never included Prepaid returns of all Endless Pool products are accepted less a 10 restocking fee up to 30 days from the date of purchase if undamaged and in its original shipping containers Accessories options and equipment that have been used are non refundable Before returning any product you must call our Customer Service Department to receive proper return authorization Fitness Machines LLC 1601 Dutton Mill Rd Aston PA 19014 800 910 2714 ENDLESS POOLS ANTER TEx IAs GI ENDLESS POOLS 2008 VGB Compliant Sw MM MG NMAGHIa cn Fitness Machines LLC 1601 Dutton Mill Rd Aston PA 19014 293 D40055 0912 800 910 2714 610 497 8693 fax e www myendlesspool com 2012 Endless Pools
49. mounted at the front of the pool A minimum of 24 horizontal clearance is required at the front of the pool for the Drive Mechanism The combination in wall cover track and liner hanger will raise the coping off the rein forcing channel by 2 1 8 The coping or other finish material covering the front edge of the pool must be constructed so to not interfere with the operation of the cover At a minimum access must be maintained in the finished work for the track end guides at the front corners of the pool Ideally there should be access to the entire cover mechanism For more detailed information on the assembly and installation of this option please refer to the Below Deck Automatic Re tractable Security Cover Supplemental Guide 6 Optional Insulation by others To conserve heat and reduce operating costs we strongly recom mend that the Endless Pool be insulated with rigid foam Simple 2 thick rigid foam insulation boards are usually adequate and are available from any building supply house Check with your supplier for a recommended adhesive appropriate for the type of rigid in sulation that they supply Be sure to leave access to all of the panel cutouts when you are installing the insulation Be sure to consider the danger of freezing for any pipes running outside the insulation ENDLE SS POOLS Refer to the appropriate Supplemental Guide if you pur chased one of our optional Skirting Kits Fig 6 If you have selected
50. mp and 5 HP hydraulic power unit runs off one 30 amp single phase GFCI protected 220 volt service A minimum of 1OAWG wire should be used for all field wiring We recommend you install a shut off within 5 of where you intend to place your power unit Please read this Owner s Manual and all associated Supplemental Guides prior to beginning your project Installation Instructions Table of Contents Pool Arrival and Inspection 0 00 00 2 WING to ohh edad uate AC doo es 15 Site Preparation ern on ees Lewes ba eh anon eae 2 Bonding and Grounding AE EE REN SEELEN ox 18 Assembly of Pool Panels Overview 2 Heater Controller 2 art NEE EE Ee ss 18 Automatic Retractable Security Cover 2 Water Quality Isolation Cover 19 Optional Insulation 204444424 neecdowdsas Ee bea 2 Hydraulic Hose Connections 0 000000 0 0 19 Liner Hanger EE 3 Optional Antenna Extension 19 Optional Liner Hangers 24 EE AE Ne e 4 Optional Retractable Security Cover System 20 Liner Underlayment aea aaa a aa ee a a RAE tacks 5 Optional UV Sanitizer eg EE tee gg 20 WAGE EE 6 Optional Treadmill 0 0 0 0 eee 20 Thru Wall Connections 9005 lt lt 508 a0 68 4 oc aKdemesiann 7 Optional Hydrotherapy Jets System 20 Swim Current Component Assembly 7 Optional Underwater Lights System 20 Thru Wall Connections J Optional Corner Step a d re
51. mp as the temperature drops The colder the temperature the more frequently the pump will turn on The Smart Winter Mode indicator light see Keypad Function section is illuminated when this feature is activated The heater controller also is programmed to turn the optional hy drotherapy jet pump on 4 times daily for 60 seconds Heater Controller The in xe is a heater controller used by Endless Pools to control the following water quality features e Water temperature can be set between 59 F and 104 F Default set point at 84 F The set point is changed with the up and down keys e The Circulating Pump CP is always on The heater can only turn on when CP is on e Pressing the light key will turn lights on off with an on time of 120 minutes e Optional Pump 1 is for a single speed Jet pump Pressing the first key turns pump 1 on off with a run time of 30 minutes The heating element is turned off when Pump 1 is activated To aid in filtration there are 4 purges per day e Optional UV always on except when Pump 1 is on and remains off or 30 minutes after pump 1 is turned on e Holding first key for 5 seconds will turn off all devices for 30 minutes to allow for servicing Pressing again will return to nor mal operation in xe UL CSA electrical specifications Input rating 120 240 VAC 2 phase required with neutral 48 A maximum 60Hz Software limited to 24A Install on a 30A GFCI circuit 22
52. nd wire exiting the top of the housing around one of the screws prior to tight ening Fig 37 If you have purchased a Raised Rear Bench Seat then that option should be installed at this time as well Refer to the Raised Bench Seat for a 48 amp 54 Pool for more detailed information After the the Skimmer Filter has been installed continue filling the pool until the top row of the honeycomb grill of the propulsion housing has been covered Tabs of shroud side are to be inserted into slot in wing caps Connect the suction hose to each insert elbow prior to placing skimmer filter assembly Fig 35 1 2 Stainless Steel Screw Fosition suction hose inside skimmer filter housing as shown Wrap bond wire around mounting screw prior to tightening ENDLESS POOLS ENDLE SS POOLS 2 5 8 66mm 25 4mm Antenna Connection Wireless Controller High Pressure Connection Low Pressure Connection 16 Keypad Additionally the placement of the keypad needs to be con sidered The majority of our customers place the keypad in the coping at the front of the pool However the keypad can be placed anywhere in the pool coping or the outside vertical finish The only constraint is the length of the cord between the keypad and the poolside water quality system When installing the keypad drill two 1 diameter holes at 2 5 8 from center to center Then with an appropriate saw cu
53. nnect the run hoses The low pressure hose lowest hydraulic hose on the front panel gets connected to the connection on the black fill cap The high pressure hose gets connected to the fitting on the high pressure manifold Fig 39 Endless Pools Inc supplies a special vegetable based hydraulic fluid created for this application and this equipment Do not use a substitute hydraulic fluid Extra hydraulic fluid is pro vided for longer hose runs Any excess fluid should be retained for future use Make sure that the power is turned off to the power unit Re move the fill black fill cap and remove the oil filter by lifting it out of fill opening Use the provided paper funnels and fill the reservoir to with in 2 of the top Once filled replace the oil filter and ensure that it is seated properly before putting the fill cap back on If you have selected a longer run hose we have provided extra fluid In this case turn the unit on and let it run for one minute to fill the run hoses Turn the power off remove the fill cap and oil filter and add fluid as needed Again you want to fill the reservoir to within 2 of the top The power unit controller comes equipped with an automatic timer shutting off the system 30 minutes after receiving its last command Because the controller remembers the last speed at which is turned off it will return to that same pace when it is turned back on 14 18 Electrical Wiring Connections 60
54. nough so that the skimmer body can rotate Fig 32 Glue the PVC straight nut into the IN port at the bottom of the skimmer body Glue the 1 1 2 slip x 1 1 2 female pipe thread adapter into the OUT port Then thread the suction fitting into the straight nut and thread the insert elbow into the adapter Fig 33 Attach the skimmer filter shroud side to the shroud top with the provided screws as shown The elbow attached to the bottom of the skimmer is to be closer to the housing Spin the shroud top pre attached to the skimmer filter as necessary Fig 34 I5 Skimmer Filter Installation cont Connect the provided suction hose to the two insert elbows 1 attached to the skimmer filter and 1 attached to the thru wall fitting Secure the hose with the provided plastic hose clamps Fig 35 Note If installing into a Dual Propulsion Pool then the skimmer filter assembly will be attached to the right propulsion housing Next insert each of the tabs in the bottom of the shroud into its corresponding slot in the wing cap The excess hose should be place behind and to the right of the skimmer filter body Secure the shroud top to the PVC angle bracket with the provided 1 2 stainless steel screws Fig 36 Restart filling the pool Once the water level is just below the Housing Lid temporarily remove the Housing Lid Use the provided 1 self drilling screw to attach the housing to the pool wall Make sure to wrap the bo
55. ock into place 3 Straighten pins to allow cord to properly attach 4 Check for continuity on fuse and replace if necessary 1 Remove air from housing prime pump 2 Add water to pool should be 1 2 way up skimmer opening 3 Clean filter s 4 Open valve or remove plug 5 Plug pump in Plug must lock into place 6 Condition is normal 7 Turn pump back on by pressing key 1 on keypad or wait 30 minutes for auto restart of circulating pump 8 Check for continuity and replace if necessary 9 10 amp fuse may be blown inside heater controller heater controller If fuse not blown turn off breaker for 5 minutes and reset If still no voltage to receptacle replace heater controller 1 Remove pump from system take apart pump and clean ceramic ball that the impeller sits on 2 Remove air from housing prime pump 3 Replace pump 1 Controller not calling for heat check thermostat set point 2 Check element continuity 14ohms Replace if not in this range 3 Insulate pool Keep pool covered when not in use Refer to Retaining Heat Service Instruction ENDLE SS POOLS 9 Keypad Functions and Troubleshooting 2S Le US uly Ay SS V Smart Winter Mode Indicator Jet Pump Indicator Light Indicator Filter Indicator Heat Indicator Set Point indicator Smart winter mode indicator Key Light key Up key Down Key 10 Troubleshooting Error Code
56. onto the provided flexible PVC and cut it to that length Use the provided PVC cleaner and cement to glue the cut pipe into the tailpiece socket Make sure to apply cleaner then cement to both faces of the glue joint X 1 1 4 ENDLE SS POOLS 14 Water Quality System cont Cut the excess pipe off of the pre plumbed return assembly so that the end of the vertical pipe is just above the top most edge of the horizontal pipe Fig 29 Finally glue the slip x slip elbow onto both the vertical and horizontal pipe Make sure to apply PVC cleaner then ce ment to both faces of each glue joint Either the heater controller union or pre plumbed return assembly union can be broken to make this step easier Fig 30 15 Skimmer Filter Installation If not done so already attach the PVC angle bracket to the right side of the propulsion housing with the provided screws Fig 31 EE rr These connections can be undone to make gluing elbow into place easier 2 S Ki me EN Lock Ring IN Fort Glue joint Apply Teflon Tape to threads prior to installing 1 2 Stainless Steel Screw ENDLESS POOLS I5 Skimmer Filter Installation cont Remove the lock ring from the filter body Loosely place the skimmer body into the shroud top Re install the lock ring The lock ring should be tightened to the point where the skimmer body is seated firmly against the shroud top but loose e
57. ool For outdoor in stallations a weather resistant can is provided for added protection A 22 cord connects these lights and plugs directly into the heater controller The lights are then operated by the pool side controls 20 30 Optional Corner Step To assist with access to the Endless Pool optional Corner Steps are available inside the Endless Pool in any of the four corners For a more complete discussion about access to an Endless Pool please refer to the Planning Guide These optional steps are ap proximately 11 high and are secured to the internal Water Re turn Channel They are easily installed using a phillips screwdriver If you wish to order them after the pool has shipped contact the Customer Service Department and they will ship one to the address provided The optional Corner Step is de scribed more fully in the Supplemental Guide 31 Optional Interior Stair For those needing an easier route into the pool our Optional In terior Stair provides easy access Typically installed with fully in ground Endless Pools the Interior Stair allows the user to gradually enter the water from deck height Interior stair con figurations depend on the panel height purchased Optional In terior Stairs are described more fully in the appropriate Supplemental Guides The Interior Stairs should be ordered with the pool to avoid substantial additional freight charges due to the size and weight of the box needed to ship the steps
58. plemental Guide An optional Tension Strap and Floor Leveling Kit is available for out of level or non smooth sites If a new slab is poured consult your local electrical codes regarding grounding and bonding Many areas require a bonding wire to be attached to the reinforcing bar that is buried in the concrete Drainage should be provided at the pool It is ideal to install a floor drain in the area just outside of the front pool panel but not directly under the panel or pool itself In installations where this is not possible installation of a secondary containment system to help divert water to a more desirable location is recommended Please call the Customer Service Department if you need any as sistance in the design of a containment system It is extremely important to ensure that any water that may reach the bottom flange of the pool panel by splashing run off or ac cidental leakage be drained away immediately With the bottom flange of the pool panel standing in water corrosion may occur over time It is worth the time and effort now to install a drainage system rather than be unprepared in the event of a mishap 3 Assembly of Pool Panels Provided with this Installation and User s Manual will be the ap propriate panel assembly Supplemental Guide for the Swim Cur rent that has been chosen This Guide will take you through assembling the panels anchoring the panels and drilling the appropriate holes into
59. plied by Endless Pools Inc to the length specified Often they are not shipped with the pool as the exact length is un known at the time of shipment Please order these hoses a week before they are needed to allow shipment by UPS ground Two hoses up to 25 feet in length are supplied at no additional charge It is best to use hoses close to the length you need rather than simply going with the standard 25 feet There is an additional charge for lengths in excess of 25 feet Remove the protective plugs and connect the 2 hydraulic hoses to the 2 ports on the Power Unit and tighten firmly Do not over tighten The hose connecting to the fill cap on the Power Unit is the return low pressure hose which gets connected to the lowest hydraulic hose at the front panel The high pressure hose which is connected to the fitting on blue high pressure manifold connects to the higher hose at the front of the pool Adapters have been provided in the hydraulic hose electrical whip box to connect the hy draulic run hose to the hoses penetrating the front panel The hoses that go through the panels are a smaller diameter than your run hose you will find adapters in the Electrical Whip box to make these connections If the hoses you or dered are too short and you need longer hoses call Cus tomer Service Extra care should be taken that these hoses are cushioned when they pass by anything that could rever berate This will ensure a quieter installation Us
60. r flange then secure the rest of the hanger to the end and side panels using shims when not securing through the channel The hanger pieces should be flush with the inside of the reinforcing channel and will protrude into the pool the thickness of the channel everywhere else Once the corner lengths are secured install the remaining two lengths of liner hanger along the side of the pool These pieces vary in length depending upon your pool size so they may need to be trimmed It is important that the gap at any joint between two liner hanger pieces be no greater than 1 8 Caulk the gap between the liner hanger and the panel to ensure that no water falling on the top flange of the pool panel can work its way down behind the liner With the same objective in mind later caulk the joint between the top of the liner hanger and the coping that you install over the entire top flange of the pool NOTE PANELS ARE SHOWN IN A FULLY ABOVE AROUND CONFIGURATION WITH OPTIONAL SKIRTING amp SYNTHETIC COPING OTHER INSTALLATIONS MAY VARY OPTIONAL SKIRTING klal FOAM RECOMMENDED BY OTTERS CUT TO FIT WITHIN PANEL BAYS INSULATION UU MIN JOIN INSULATION BOARDS e CORNERS amp TAPE SEAMS C TYPICAL IN CONFIGURATIONS 2 amp 2 INSULATION EE Ce TOP FLANGE OF POOL PANEL PLAN VIEW NOTE INSTALL INSULATION PRIOR TO ANCHORING PANELS IN INSTALLATIONS WITH RECESSED APPEARANCES SILICONE SEALANT AROUND PERIMETER
61. r to wipe down all the surfaces in the pool Increasing free chlorine level temporarily to 5 ppm will help as will maintaining the free chlorine level in the pool at 3 ppm until the water is clear Test the chlorine level frequently during this time If you have selected the gas heater for your Endless Pool we would encourage you to have the heater serviced on a yearly basis This is very important if you have elected to put the gas heater outdoors or if the pool is drained for extended periods of time ENDLESS POOLS 7 Draining Your Endless Pool 1 Disconnect electrical power to all pool equipment 2 Begin to drain down pool water by placing a suitable sump pump in the pool or by setting up a siphon using a garden hose If using a siphon two or more hoses may be used simultane ously in order to expedite the process 3 If you have full depth stairs they should be unfastened from the panel and shifted away from the corner enough to a re move the corner cover underneath and b allow the liner to pull in toward the pool a little bit If you have a corner step remove the step as the water level lowers to the top of that step Once the water is within an inch or two from the top of the benches remove the 4 corner covers located in the corners of the pool These covers should be removed by unscrewing the 4 machine screws found on the tops of all the covers 4 Continue draining pool until 6 of water is remaining in the stan
62. s ENDLESS POOLS Key Press Key 1 key twice to turn the optional jet pump on Press a third time to turn jets off A built in timer automatically turns pump off after 20 minutes unless pump has been manu ally deactivated first as The Pump 1 indicator lights up when CH Pump 1 is on Light Key Press Light key to turn light on Press a second time to turn light off A built in timer automat ically turns light off after 2 hours unless it has been manually deactivated first The Light indicator lights up when light is on Up Down Keys Use Up or Down key to set desired water temperature The temperature setting will be displayed for 5 seconds to confirm your new selection 9 The Set Point icon indicates that the display shows the desired temperature NOT the current water temperature Off Mode This mode allows you to stop all outputs for 30 minutes to perform a quick spa maintenance Press and hold Key 1 key for 5 secs to activate the Off mode Quick press Key 1 key to reacti vate the system before the expiration of the 30 minute delay While the Off mode is engaged the display will toggle between OFF and the water temperature Jet Pump Light indicator key indicator Light key Set Point indicator Heat indicator Filter indicator Up key Down Key Hr An internal hardware error has been detected in in xe Contact Customer Service HL The system h
63. s through the wall of an Endless Pool the user can enjoy the therapy benefits of jets in addition to the variable speed swim cur rent Installation is relatively straightforward but roughly doubles the plumbing work required The kit provided by Endless Pools Inc includes everything necessary with the exception of the 1 1 2 schedule 40 PVC pipe Detailed instructions are included in the Supplemental Guide along with a typical layout drawing When jets are installed it is important to leave access to the outside of the pool panel for service The holes for the jets should be cut before installing the liner If the pool is located outdoors where freezing is an issue care must be taken with the jet system plumbing Ad ditional insulation should be considered under these conditions Call Customer Service with any questions about this limitation 29 Optional Underwater Lights System Underwater Lights are an important aesthetic option Typically located on either the side or the end wall of the pool these two lights thread into in niches that are installed after the liner is in place The holes for these niches are cut using the holesaw pro vided before the foam and the liner are installed Directions come with the lights which are packaged in the pool crate These direc tions are also found in the Supplemental Guide Each light con sists of a dry niche which serves as a porthole The low voltage light threads into this porthole outside the p
64. stall the thru wall fitting as shown in Fig 22 Before installing the four jets refer to the Endless Pool Jet Hydrotherapy Supplemental Guide The 1 2 venturi piping will need to be secured to the jet body prior to permanently installing them 14 Water Quality System Note If you have purchased the Optional UV Sanitizer then refer to that Supplemental Guide at this time as these instructions will have been modified to accept this option The Water Quality thru wall assemblies should be installed by this point Attach the pre plumbed suction assembly to the suction thru wall Make sure to wrap Teflon tape around the threads of the adapter that is glued into the thru wall The union of the pre plumbed suction can be taken apart to make this step easier Fig 23 Attach the circulating pump to the bottom of the pre plumbed suction assembly Make sure that the pump union o ring is seated properly prior to installing Fig 24 Next attach the pump to heater pre plumbed assembly to the pump as shown Again make sure that the pump union o ring is seated properly prior to installing Fig 25 Pre plumbed Suction Assembly Pump Union O Ring Circulating Pump Pump to Heater Pre plumbed Assembly This next step is best done with a helper Align the heater controller with the pump to heater pre plumbed assembly Make sure the T gasket is seated properly prior to tightening the heat
65. t out the piece between the two holes Next peal off the adhesive protection on the backside of the keypad Feed the keypad cord through the cutout Firmly press the keypad into place Then feed the bracket through the cord and push the bracket all the way up to the underside of the coping Make sure that the bracket is placed over the two threaded studs on the back of the keypad Once that is completed thread the two wing nuts over the threaded studs and hand tighten them If you are going to have your keypad in a horizontal surface that is deeper than the threaded studs then simply cut your holes remove the adhesive protection feed the cord into the hole and firmly press the keypad into place When picking a location for the keypad in your finish work it is important to make sure it is within 10 of the Heater Controller 17 Power Unit The power unit should be placed on flat and level surface If the power unit is to be placed outside we recommend selecting our Outdoor Power Unit with Weather Guard to protect it against everyday elements Whether placed indoors or out doors this is an air cooled unit and must have ample ventila tion Therefore a minimum of 12 of air spaced must be provided on all sides of the power unit In addition the power unit needs to be check periodically for maintenance and should be accessible The power unit is heavy take care when placing the power unit Once the power unit is in place co
66. the panels It is critical that this Guide be referenced at this point Any required hole must be drilled before proceeding with the installation An Endless Pool is usually customized to meet the needs of the end user Pools of different lengths and widths are selected as well as deeper pools Naturally the installation will vary depending on the options selected so it is important to understand exactly what has been supplied On the day your pool ships you will receive an email with a customized owner s manual containing the appro priate Supplemental Guides for the options that were purchased A hard copy of that same owner s manual will be packaged in the pool crate Please review all appropriate Supplemental Guide be fore proceeding with the installation to ensure that selected op tions have been considered Additionally the placement of the Water Quality System keypad needs to be considered The majority of our customer s place the keypad in the coping of the pool However the keypad can be mounted in the skirting or on a nearby wall as an alterna tive Please refer to the Keypad Section of these installation in structions for a more detailed description 5 Automatic Retractable Security Cover If you have purchased a Below Deck Automatic Retractable Se curity Cover BDARSC then the installation must begin at this time The cover mechanism and bracket will be attached directly to the pool panels The BDARSC must be
67. urchaser and which our examination shall disclose to our satisfaction to be thus defective All labor costs for removal and re installation of the defective part and all freight charges shall be paid by the purchaser and will not be reimbursed by Fitness Machines LLC This warranty is expressly in lieu of all other warranties expressed or implied including the warranties of merchantability and fitness for use and of all other obligations or liabilities for all damages direct or consequential to person property or business whether or not occasioned by our negligence and we neither assume for us any other liability in connection with the sale of this Endless Pool IN ADDITION ENDLESS POOLS OFFERS A TEN YEAR STRUCTURAL WARRANTY ON THE STEEL WALL PANEL SYSTEM Ifa panel should deteriorate beyond structural use in this ten year period we will repair or replace the panel at our option after receipt and inspection of the defective panel The structural warranty is voided when suitable drainage is not provided and or panels are not properly bonded as stipulated in the installation instructions THIS WARRANTY SHALL NOT APPLY TO THIS ENDLESS POOL OR ANY PART THEREOF WHICH HAS BEEN SUBJECT TO SALT CHLORINE GENERATORS ACCIDENT NEGLIGENCE FREEZING IMPROPER INSTALLATION OR OPERATION ALTERATION ABUSE OR MISUSE THIS INCLUDES BUT IS NOT LIMITED TO FLOW RESTRICTIONS OR OBSTRUCTIONS ON ALL WATER AND HYDRAULIC SYSTEMS AND NOT MAINTAINING PROPER WATER CHEMISTRY

INSTALLATION, OPERATIONS AND USER`S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents