Home

User manual - MCM Electronics

Contents

1. Do not install the product on an unstable or vibrating surface insecure shelf sloped surface etc e The product may fall and break or cause a personal injury e Using the product in an area with excess vibration may damage the product or cause a fire Do not install the product in a vehicle or a place exposed to dust moisture water drips etc oil or smoke e An electric shock or fire may result Do not expose the product to direct sunlight heat or a hot object such as a stove e Otherwise the product lifespan may be reduced or a fire may result Do not install the product within the reach of young children e The product may fall and injure children Edible oil such as soybean oil can damage or deform the product Do not install the product in a kitchen or near a kitchen counter Take care not to drop the product when moving it e Otherwise product failure or personal injury may result Do not set down the product on its front e The screen may become damaged When installing the product on a cabinet or shelf make sure that the bottom edge of the front of the product is not protruding e The product may fall and break or cause a personal injury e Install the product only on cabinets or shelves of the right size Before Using the Product Before Using the Product A Warning
2. Put down the product carefully e The product may fall and break or cause a personal injury Installing the product in an unusual place a place exposed to a lot of fine particles chemical substances or extreme temperatures or an airport or train station where the product should operate continuously for an extended period of time may seriously affect its performance e Besure to consult Samsung Customer Service Center page 149 before installation if you want to install the product at such a place High voltage runs through the product Do not attempt to disassemble repair or modify the product on your own e An electric shock or fire may result e Contact Samsung Customer Service Center page 149 for repair Before moving the product turn off the power switch and disconnect the power cable and all other connected cables e Otherwise the power cord may be damaged and a fire or electric shock may result If the product generates a strange noise a burning smell or smoke remove the power cord immediately and contact Samsung Customer Service Center page 149 e An electric shock or fire may result Do not let children hang from the product or climb on top of it e The product may fall and your child may become injured or seriously harmed If the product falls or the exterior is damaged power off the product remove the power cord and contact Samsung Customer S
3. Icons Description Open or close the onscreen display OSD menu or return to the parent menu e OSD control lock Maintain the current settings or lock the OSD control to prevent unintended changes to settings e Enable To lock the OSD control press and hold the MENU button for 10 seconds e Disable To unlock the OSD control press and hold the MENU button for more than 10 seconds MENU K Ifthe OSD control is locked e Brightness Contrast and fa GicAngle can be adjusted and INFORMATION can be viewed e The Customized Key function can be used by pressing the Cr button The Customized Key is available even when the OSD control is locked Configure Customized Key and press 4 The following options will be enabled MacicAngle mAc cBright Eco Saving Image Size 14 To configure Customized Key go to SETUP amp RESET Customized Key and select the mode you want 1 Preparations Preparations Icons Description Move to the upper or lower menu or adjust the value for an option on the A V OSD menu bog Use this button to control the brightness and contrast of the screen owe Confirm a menu selection Press the AUTO button to automatically adjust the screen settings AUTO K Changing the resolution in Display Properties will activate the Auto Adjustment function amp Turn the screen on or off Function Key Guide When a contro
4. 17 5 x 13 7 x 7 0 Inches 4 6 lbs Dimensions Without 445 x 273 x 53 mm 467 x 283 x 53 mm Wx H x D Stand 17 5 x 10 7 x 2 1 Inches 18 4x 11 1 x 2 1 Inches Weight With Stand 445 x 348 x 177 mm 2 1 kg 467 x 357 x 177 mm 2 4 kg 18 4 x 14 1 x 7 0 Inches 5 3 lbs VESA Mounting Interface 75 mm x 75 mm 3 0 Inches x 3 0 Inches Environmental Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 96 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 96 95 96 non condensing z 1 6 Specifications 131 Specifications Model Name S19C150F S20C150FL Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may be brighter or darker on the LCD panel This does not affect product performance Specifications 16 3 General S20C150NL Model Name Panel Size S20C150NL 19 5 Inches 49 cm Display area 432 mm H x 239 76 mm V 17 0 Inches H x 9 4 Inches V Pixel Pitch 0 27 mm H x 0 27 mm V 0 011 Inches H x 0
5. 5 5 Screen Setup SAMSUNG MAGIC Angle MAGIcAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle K This option is not available when MA icBright is in Cinema or Dynamic Contrast mode This feature provides the viewing angle brightness and tint to suit your preferences 5 5 1 Configuring SAMSUNG MAGIC Angle 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press 3 c on the product 3 Press 4 W to move to St Angle and press 17 8 on the product The following screen will appear Off Lean Back Mode 1 Lean Back Mode 2 Standing Mode Side Mode Group View Custom KI iv 4 AUTO O v v v v v v Off D Select this option to view directly in front of the product e Lean Back Mode 1 Select this option to view from a place slightly lower than the product e Lean Back Mode 2 O Select this option to view from a place lower than Lean Back Mode 1 e Standing Mode Select this option to view from a place higher than the product e Side Mode OF Select this option to view from either side of the product e Group View Select this option for more than one viewer to view from places D and e Custom Lean Back Mode 1 will be applied by default if Custom is selected 4 Press M V to move to
6. y Setup and Reset 10 5 Key Repeat Time Control the response rate of a button when the button is pressed 10 5 1 Configuring Key Repeat Time 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 2 3 on the product 3 Press 4 W to move to Key Repeat Time and press 7 c on the product The following screen will appear SETUP amp RESET Acceleration 1 sec 2 sec No Repeat 4 LY 4 NUO v v v v v v e Acceleration 1 sec or 2 sec can be selected If No Repeat is selected a command responds only once when a button is pressed 4 Press 4 W to move to the option you want and press 3 c 5 The selected option will be applied 10 Setup and Reset 99 y Setup and Reset 10 6 Customized Key You can customize Customized Key as follows 10 6 1 Configuring Customized Key 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Customized Key and press 3 C on the product The following screen will appear SETUP amp RESET HRG Br Eco Saving Image Size KE a AUTO v v v v v v e MA amp cBright Eco Saving Image Size 4 Press A
7. 2 Press A W to move to SETUP amp RESET and press 2 3 on the product 3 Press A V to move to Customized Key and press 9 on the product The following screen will appear SETUP amp RESET SAMSUNG MAGIC Angle MAGIC Bright Eco Saving Image Size La Lv 4 AUTO O v v y v y v e mAe cAngle MagicBright Eco Saving Image Size 4 Press M V to move to the option you want and press a 5 The selected option will be applied 12 Setup and Reset 114 A Setup and Reset 12 9 Auto Source You can activate Auto Source 12 9 1 Configuring Auto Source 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A V to move to SETUP amp RESET and press II C2 on the product Press A V to move to Auto Source and press I C on the product The following screen will appear SETUP amp RESET Auto Manual La Lv 4 AUTO O v v v e Auto The input source is automatically recognized e Manual Manually select an input source Press A V to move to the option you want and press 7 c The selected option will be applied 12 Setup and Reset 115 Va Setup and Reset 12 10 Display Time Set the on screen display OSD menu to automatically disappear if the menu is not used for a specified period of time Display Time can be used to specify the time after which you want
8. MOROCCO 080 100 2255 http www samsung com OMAN 800 SAMSUNG 726 7864 http www samsung com ae English http www samsung com ae_ar Arabic Appendix 153 Appendix MENA PAKISTAN 0800 Samsung 72678 http Awww samsung com pk QATAR 800 2255 800 CALL http www samsung com ae English http www samsung com ae_ar Arabic SAUDI ARABIA 920021230 http www samsung com sa SYRIA 18252273 http www samsung com Levant English TUNISIA 80 1000 12 http www samsung com n_africa TURKEY 444 7711 http www samsung com U A E 800 SAMSUNG 726 7864 http www samsung com AFRICA BOTSWANA 8007260000 http www samsung com BURUNDI 200 http www samsung com CAMEROON 7095 0077 http www samsung com africa_fr COTE D IVOIRE 8000 0077 http www samsung com africa_fr DRC 499999 http www samsung com GHANA 0800 10077 http www samsung com africa_en 0302 200077 KENYA 0800 545 545 http www samsung com NAMIBIA 08 197 267 864 http www samsung com NIGERIA 0800 726 7864 http www samsung com africa_en MOZAMBIQUE 847267864 827267864 http www samsung com RWANDA 9999 http www samsung com SENEGAL 800 00 0077 http www samsung com africa_fr SOUTH AFRICA 0860 SAMSUNG 726 7864 http www samsung com SUDAN 1969 http www samsung com TANZANIA 0685 88 99 00 http www samsung com UGANDA 0800 300 300 http www samsung com ZAMBIA
9. Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to MENU SETTINGS and press 17 c on the product Press A V to move to Menu H Position or Menu V Position and press I C2 on the product The following screen will appear MENU SETTINGS MENU SETTINGS La AUTO N v v hf v Press A V to configure Menu H Position or Menu V Position The selected option will be applied EI Aa AUTO v v v v v v 8 Coordinating OSD 8 3 Coordinating OSD Display Time Set the on screen display OSD menu to automatically disappear ifthe menu is not used for a specified period of time Display Time can be used to specify the time after which you want the OSD menu to disappear 8 3 1 Configuring Display Time T Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to MENU SETTINGS and press IQ on the product 3 Press 4 W to move to Display Time and press t c on the product The following screen will appear MENU SETTINGS 5 sec 10 sec 20 sec 200 sec 4 LY 4 lt u or v v v v v v 4 Press A V to move to the option you want and press 13 8 5 The selected option will be applied 8 Coordinating OSD 89 8 4 Coordinating OSD Transparency
10. The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance Table Of Contents BEFORE USING THE 11 PRODUCT 12 13 13 14 14 15 16 18 22 PREPARATIONS 23 28 24 25 25 27 29 31 33 33 34 35 Copyright Icons used in this manual Cleaning Securing the Installation Space Precautions for storage Safety Precautions Symbols for safety precautions Electricity and Safety Installation and Safety Operation Correct posture to use the product Checking the Contents Removing the Packaging Checking the Components Parts Frontal Button The functions available may vary depending on the product model Frontal Button The functions available may vary depending on the product model Frontal Button The functions available may vary depending on the product model Reverse Side Installation Attaching the Stand S19C150N S19C150F S200 150FL S20C150NL S22C150N S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS Attaching the Stand S19V325N PLUS S20V325B PLUS Removing the Stand S19C150N S19C150F S20C150FL S20C150NL S22C150N Table Of Contents S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S200325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS 36 Removing t
11. Set the transparency for the menu windows 8 4 1 Changing Transparency 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to MENU SETTINGS and press 9 2 on the product 3 Press A V to move to Transparency and press Q9 on the product The following screen will appear MENU SETTINGS 4 Press A W to move to the option you want and press a 5 The selected option will be applied 8 Coordinating OSD 90 9 1 Coordinating OSD The functions available may vary depending on the product model H Position amp V Position H Position Move the screen to the left or right V Position Move the screen up or down WZ gt This menu is available in Analog mode only e _ This menu is only available when Image Size is set to Screen Fit in AV Mode When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally select Screen Fit to adjust horizontal position in 0 6 levels 9 1 1 Configuring H Position amp V Position 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SIZE amp POSITION and press 4 7 on the product 3 Press A V to move to H Position or V Position and press 3 The following screen will appear EI AUTO O ve v
12. on the product The following screen will appear Mio Wide KI E 4 AUTO N bl bd v v v e Auto Display the picture according to the aspect ratio of the input source e Wide Display the picture in full screen regardless of the aspect ratio of the input source Press A V to move to the option you want and press I 2 The selected option will be applied 3 Screen Setup 55 3 7 Screen Setup H Position amp V Position H Position Move the screen to the left or right V Position Move the screen up or down 3 7 1 Configuring H Position amp V Position 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to PICTURE and press 2 C3 on the product Press A V to move to H Position or V Position and press Y 2 The following screen will appear KI AUTO v v KA v v Press A W to configure H Position or V Position The selected option will be applied 3 Screen Setup ET 3 8 Screen Setup Coarse Adjust the screen frequency 3 8 1 Adjusting Coarse 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press IQ on the product 3 Press A W to move to Coarse and press Q on the product The fol
13. 0211 350370 http www samsung com Appendix 154 Appendix Responsibility for the Pay Service Cost to Customers NG When the service is requested in spite of in warranty we may charge you for a visit from a service technician in the following cases Not a product defect Cleaning of the product Adjustment Explanation Re installation and etc fa service technician gives instructions on how to use product or simply adjusts options without disassembling product e Ifa defect is caused by external environmental factors Internet Antenna Wired Signal etc Ifa product is reinstalled or devices are connected additionally after installing the purchased product for the first time fa product is reinstalled to move to a different spot or to move to a different house e f customer requests instructions on how to use because of another company s product e If customer requests instructions on how to use the network or another company s program e f customer requests software installation and setup for the product e Ifa service technician removes cleans dusts or foreign materials inside of the product e _ lf customer requests an installation additionally after purchasing a product through home shopping or online A Product damage caused by customer s fault Product damage caused by customer s mishandling or wrong repair If a product damage is caused by e _ external impact or drop e use of suppli
14. 2 sec can be selected If No Repeat is selected a command responds only once when a button is pressed 4 Press 4 W to move to the option you want and press 3 c 5 The selected option will be applied 11 Setup and Reset 105 Setup and Reset 11 6 Customized Key You can customize Customized Key as follows 11 6 1 Configuring Customized Key 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A V to move to Customized Key and press 3 C on the product The following screen will appear SETUP amp RESET KAG Ange MAGIC Bright Eco Saving Image Size KE Y a AUTO v v e MacicAngle MagicBright Eco Saving Image Size 4 Press A V to move to the option you want and press I 5 The selected option will be applied 11 Setup and Reset 106 12 1 A Setup and Reset The functions available may vary depending on the product model Reset Return all the settings for the product to the default factory settings 12 1 1 Initializing Settings Reset 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press A W to move to Reset and press
15. Reset and press 3 c on the product The following screen will appear SETUP amp RESET Reset Eco Saving Off Timer Key Repeat Time Customized Key Off Off Acceleration RUIS Bri 4 gt Brio v v v Reset all settings 4 Press 4 W to move to the option you want and press a 5 The selected option will be applied 10 Setup and Reset 95 y Setup and Reset 10 2 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel A This menu is not available when fa GieBright is in Dynamic Contrast mode 10 2 1 Configuring Eco Saving 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 3 08 on the product 3 Press A V to move to Eco Saving and press 2 3 on the product The following screen will appear SETUP amp RESET 4 iv A a lt UK X v v v B v e 75 Change the monitor power consumption to 75 of the default level e 50 Change the monitor power consumption to 50 of the default level e Off Deactivate the Eco Saving function 4 Press A V to move to the option you want and press 3 8 5 The selected option will be applied 10 Setup and Reset 96 Setup and Reset 10 3 Off Timer You can set the product to automatically turn off 10 3 1 Co
16. Settings 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press 9 on the product 3 Press M V to move to Color Tone and press 3 C on the product The following screen will appear Cool 2 Cool 1 Normal Warm 1 Warm 2 Custom La Lv 4 AU KO v v v v v v e Cool 2 Set the color temperature to be cooler than Cool 1 e Cool 1 Set the color temperature to be cooler than Normal mode e Normal Display the standard color tone e Warm 1 Set the color temperature to be warmer than Normal mode e Warm 2 Set the color temperature to be warmer than Warm 1 e Custom Customize the color tone NG When the external input is connected through HDMI and PC AV Mode is set to AV Color Tone has four color temperature settings Cool Normal Warm and Custom e _ The function may not be supported depending on the ports provided with the product 4 Press 4 W to move to the option you want and press 3 9 5 The selected option will be applied 7 Configuring Tint 85 7 6 Configuring Tint Gamma Adjust the mid range brightness Gamma of the picture K This menu is not available when Ma gicAngle is enabled 7 6 1 Configuring Gamma 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display th
17. V to move to Eco Saving and press Q on the product The following screen will appear SETUP amp RESET 4 iv A E lt UK X v v v B v e 75 Change the monitor power consumption to 75 of the default level e 50 Change the monitor power consumption to 50 of the default level e Off Deactivate the Eco Saving function 4 Press A V to move to the option you want and press 3 8 5 The selected option will be applied 11 Setup and Reset 102 Setup and Reset 11 3 Off Timer You can set the product to automatically turn off 11 3 1 Configuring Off Timer 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to SETUP amp RESET and press II C2 on the product Press A W to move to Off Timer and press T C on the product The following screen will appear SETUP amp RESET KI y A E or v X v v v v e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically Press A V to move to the option you want and press H C The selected option will be applied 11 Setup and Reset 103 Setup and Reset 11 4 Turn Off After The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours A This option is
18. a Source Device Connecting and Using a PC Select a connection method suitable for your PC K Connecting parts may differ in different products 2 2 1 Connection Using the D SUB Cable Analogue Type WZ Do not connect the power cable before connecting all other cables Ensure you connect a source device first before connecting the power cable S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS 1 Connect the D SUB cable to the RGB IN port on the back of the product and the RGB port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC For details refer to 2 3 Connecting the Power 3 Press 13 03 to change the input source to Analog 4 Provided ports may vary depending on the product Connecting and Using a Source Device S19C150F S20C150FL S19C150N S20C150NL S22C150N S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S19V325N PLUS 1 Connect the D SUB cable to the RGB IN port on the back of the product and the RGB port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC For details refer to 2 3 Connecting the Power K Provided ports may vary depending on the product 2 2 2 Connection Using the DVI Cable S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS A WZ Do
19. of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press 3 c on the product 3 Press 4 W to move to Sharpness and press t c on the product The following screen will appear Ul AUTO O v v v v v v 4 Adjust the Sharpness using the A Y buttons 5 The selected option will be applied 3 4 Screen Setup SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used IZ This menu is not available when Eco Saving is enabled You can customize the brightness to suit your preferences 3 4 1 Configuring SAMSUNG MAGIC Bright 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press t c on the product 3 Press A V to move to MaGiceright and press 13 c on the product The following screen will appear Custom Standard Game Cinema Dynamic Contrast 4 Lv 4 AUTO v v bo y v v e Custom Customize the contrast and brightness as required e Standard Obtain a picture quality suitable for editing documents or using Internet e Game Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements e Cinema Obtain the brightness and sharpness
20. pins and power socket with a dry cloth e Otherwise a fire may result Before Using the Product Do not unplug the power cord when the product is in use e _ The product may become damaged by an electric shock Do not use the power cord for products other than authorized products supplied by Samsung e An electric shock or fire may result Keep the power socket where the power cord is connected unobstructed e If any problem occurs in the product unplug the power cable to completely cut the power to the product Power to the product cannot be completely cut off with the power button Hold the plug when disconnecting the power cord from the power socket e An electric shock or fire may result Installation and Safety A Warning DO NOT PLACE CANDLES INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES e Otherwise a fire may result Avoid installing the product in a narrow space with bad ventilation such as a bookshelf or wall closet e Otherwise a fire may result due to an increased internal temperature Keep the plastic packaging bag for the product in a place that cannot be reached by children e Children may suffocate Before Using the Product 16 Before Using the Product Es S
21. power socket DC 14V A The input voltage is switched automatically Connecting and Using a Source Device 2 3 1 Driver Installation K e You can set the optimum resolution and frequency for this product by installing the corresponding drivers e An installation driver is contained on the CD supplied with the product e fthe file provided is faulty visit the Samsung homepage http www samsung com and download the file Insert the user manual CD provided with the product into the CD ROM drive Click Windows Driver Follow the instructions given on the screen to proceed with installation Aa UNa Select your product model from the list of models Select the display adapter on which you wand to intall the monitor Select the montor which you weet to install 5 Go to Display Properties and check that the resolution and refresh rate are appropriate Refer to your Windows OS manual for further details Connecting and Using a Source Device 2 3 2 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase Select a language on the product and change the resolution on your PC to the optimum setting The optimal resolution for this monitor is as follows Use the above settings to set the resolution on your PC a English A le v a a Y v v v 1 Press A V to move to the languag
22. the OSD menu to disappear 12 10 11 Configuring Display Time 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 2 3 on the product 3 Press 4 W to move to Display Time and press t c on the product The following screen will appear SETUP amp RESET 5 sec 10 sec 20 sec 200 sec La aa 4 AUTO O v JAK v v v v 4 Press M V to move to the option you want and press a 5 The selected option will be applied 12 Setup and Reset 116 Va Setup and Reset 12 11 Menu Transparency Set the transparency for the menu windows 12 11 1 Changing Menu Transparency 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press 4 W to move to Menu Transparency and press 3 c on the product The following screen will appear SETUP amp RESET La Lv 4 AUTO O v v y v v v 4 Press M V to move to the option you want and press 5 0 5 The selected option will be applied 12 Setup and Reset KEI INFORMATION Menu and Others A 13 1 INFORMATION View the current input source frequency and resolution 13 1 1 Displaying INFORMATION 1 Press any button on the front of the pr
23. x v v v 4 Press A to configure H Position or V Position 5 The selected option will be applied 9 2 Coordinating OSD Image Size Change the picture size 9 2 1 Changing the Image Size 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to SIZE amp POSITION and press 9 on the product 3 Press M V to move to Image Size and press Q c on the product The following screen will appear In PC mode am Lv 4 AUTO v v v v v v e Auto Display the picture according to the aspect ratio of the input source e Wide Display the picture in full screen regardless of the aspect ratio of the input source In AV mode AUTO 3 v v v e 4 3 Display the picture with an aspect ratio of 4 3 Suitable for videos and standard broadcasts e 16 9 Display the picture with an aspect ratio of 16 9 e Screen Fit Display the picture with the original aspect ratio without cutting off NG e Changing the screen size is available when the following conditions are satisfied e The function may not be supported depending on the ports provided with the product a A digital output device is connected using the DVI cable 9 Coordinating OSD 92 Coordinating OSD o The input signal is 480p 576p 720p or 1080p and monitor can display normally Not every model can support all of
24. 011 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7 M Resolution Optimum 1600 x 900 60 Hz Resolution Maximum 1600 x 900 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 136 MHz Analog Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable 476 2 x 299 8 x 53 mm 18 7 x 11 8 x 2 1 Inches Dimensions Without WxHxD Stand Weight With Stand 476 2 x 379 4 x 187 mm 2 4 kg 18 7 x 14 9 x 7 4 Inches 5 3 lbs Environmental Operating considerations Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 118 F 20 C 45 C Humidity 5 95 non condensing 16 Specifications 133 Specifications Model Name S20C150NL Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired P
25. 3 on the product The following screen will appear SETUP amp RESET Reset Language Eco Saving Off Timer On Off PC AV Mode Key Repeat Time Acceleration bo La Lv 4 DD BAO Reset all settings 4 Press M V to move to the option you want and press a 5 The selected option will be applied 12 Setup and Reset TVA Setup and Reset A 12 2 Language Set the menu language e A change to the language setting will only be applied to the onscreen menu display e Tt will not be applied to other functions on your PC 12 2 1 Configuring Language 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to SETUP amp RESET and press 13 c on the product 3 Press A V to move to Language and press R c on the product The following screen will appear SETUP amp RESET Deutsch English Espa ol EI LY 4 gt auo oO 4 Press A V to move to the language you want and press 3 ce 5 The selected option will be applied 12 Setup and Reset 108 Va Setup and Reset 12 3 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel A This menu is not available when FAG cBright is in Dynamic Contrast mode 12 3 1 Configuring Eco Saving 1 Press any button on the front of the product to disp
26. 6 875 75 000 49 500 MAC 832 x 624 49 726 74 551 57 284 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 MAC 1152 x 870 68 681 75 062 100 000 VESA 1280 x 720 45 000 60 000 74 250 VESA 1280 x 800 49 702 59 810 83 500 VESA 1440 x 900 55 935 59 887 106 500 VESA 1440 x 900 70 635 74 984 136 750 VESA 1600 x 900 RB 60 000 60 000 108 000 16 Specifications Specifications S22C150N Resolution Haha a gt ni pa iran kHz Hz IBM 720 x 400 31 469 70 087 28 322 MAC 640 x 480 35 000 66 667 30 240 MAC 832 x 624 49 726 74 551 57 284 MAC 1152 x 870 68 681 75 062 100 000 VESA 640 x 480 31 469 59 940 25 175 VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 VESA 1280 x 720 45 000 60 000 74 250 VESA 1280 x 800 49 702 59 810 83 500 VESA 1280 x 1024 63 981 60 020 108 000 VESA 1280 x 1024 7
27. 7 5 x 11 4 x 2 6 Inches 478 x 291 x 53 mm 18 8 x 11 5 x 2 1 Inches Dimensions Without WxHxD Stand Weight With Stand 445 x 362 x 198 mm 2 1 kg 17 5 x 14 3 x 7 8 Inches 4 6 lbs 478 x 365 x 177 mm 2 1 kg 18 8 x 14 4 x 7 0 Inches 4 6 lbs 16 Specifications 139 Specifications Model Name S19V325N PLUS S20C325B PLUS VESA Mounting Interface 75 mm x 75 mm 3 0 Inches x 3 0 Inches Environmental Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 96 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 Yo 95 Yo non condensing Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may be brighter or darker on the LCD panel This does not affect product performance 16 Specifications 140 Specifications 16 7 General S20G325B PLUS S20H325B PLUS Model Name S20G325B PLUS S20H325B PLUS Panel Size 20 Inches 50 cm Display area 442 8 mm H X 249 08 mm V 17 4 Inches H x 9 8 Inches V Pixe
28. 815 56480 http www samsung com POLAND 0 801 172 678 http www samsung com pl lub 48 22 607 93 33 catkowity koszt potaczenia jak za 1 impuls wedtug taryfy operatora koszt po czenia wed ug taryfy operatora PORTUGAL 808 20 SAMSUNG 808 20 7267 http www samsung com ROMANIA 08008 SAMSUNG 08008 726 http www samsung com ro 7864 TOLL FREE No SERBIA 011 321 6899 http www samsung com rs Appendix 151 Appendix EUROPE SLOVAKIA 0800 SAMSUNG 0800 726 786 http www samsung com SPAIN 902172678 http www samsung com SWEDEN 0771 726 7864 SAMSUNG http www samsung com SWITZERLAND 0848 SAMSUNG http www samsung com ch 7267864 CHF 0 08 min German http www samsung com ch_fr French U K 0330 SAMSUNG 7267864 http www samsung com CIS ARMENIA 0 800 05 555 http www samsung com AZERBAIJAN 088 55 55 555 http www samsung com BELARUS 810 800 500 55 500 http www samsung com GEORGIA 0 800 555 555 http www samsung com KAZAKHSTAN 8 10 800 500 55 500 http www samsung com GSM 7799 KYRGYZSTAN 00 800 500 55 500 http www samsung com MOLDOVA 0 800 614 40 http www samsung com MONGOLIA 7 800 555 55 55 http www samsung com RUSSIA 8 800 555 55 55 http www samsung com TADJIKISTAN 8 10 800 500 55 500 http www samsung com UKRAINE 0 800 502 000 http www samsung com ua Ukrainian http www samsung com ua_r
29. 9 976 75 025 135 000 VESA 1440 x 900 55 935 59 887 106 500 VESA 1600 x 900 RB 60 000 60 000 108 000 VESA 1680 x 1050 65 290 59 954 146 250 VESA 1920 x 1080p 67 500 60 000 148 500 o Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle The reciprocal number of a horizontal cycle is called horizontal frequency Horizontal frequency is measured in kHz e Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures The repeat frequency is called vertical frequency or refresh rate and is indicated in Hz 16 Specifications 148 Appendix Contact SAMSUNG WORLD WIDE IZ Ifyou have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center NORTH AMERICA U S A 1 800 SAMSUNG 726 7864 http www samsung com us CANADA 1 800 SAMSUNG 726 7864 http www samsung com ca English http www samsung com ca_fr French LATIN AMERICA ARGENTINE 0800 333 3733 http www samsung com ar BOLIVIA 800 1 0 7260 http www samsung com BRAZIL 0800 124 421 Demais cidades e http www samsung com br regi es 4004 0000 Capitais e grandes centros CHILE 800 SAMSUNG 726 7864 http www samsung com cl COLOMBIA 01 8000 112 112 http www samsung com co Bogota 600 12 72 COSTA R
30. IC Bright 53 62 72 SAMSUNG MAGIC Color 81 SAMSUNG MAGIC Upscale 54 64 Sharpness 52 61 71 Standard Signal Mode Table 146 T Terminology 157 Transparency 90 Turn Off After 98 104
31. ICA 0 800 507 7267 http www samsung com latin Spanish http www samsung com latin_en English DOMINICA 1 800 751 2676 http www samsung com latin Spanish http www samsung com latin_en English ECUADOR 1 800 10 7267 http www samsung com latin Spanish http www samsung com latin_en English EL SALVADOR 800 6225 http www samsung com atin Spanish http www samsung com latin_en English Appendix 149 Appendix LATIN AMERICA GUATEMALA 1 800 299 0013 http www samsung com latin Spanish http www samsung com latin_en English HONDURAS 800 27919267 http www samsung com latin Spanish http www samsung com latin_en English JAMAICA 1 800 234 7267 http www samsung com NICARAGUA 001 800 5077267 http www samsung com latin Spanish http www samsung com latin_en English MEXICO 01 800 SAMSUNG 726 7864 http www samsung com PANAMA 800 7267 http www samsung com latin Spanish http www samsung com latin_en English PARAGUAY 009 800 542 0001 http www samsung com py PERU 0 800 777 08 http www samsung com pe PUERTO RICO 1 800 682 3180 http www samsung com TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 http www samsung com URUGUAY 000 405 437 33 http www samsung com VENEZUELA 0 800 100 5303 http www samsung com ve EUROPE AUSTRIA 0810 SAMSUNG http www samsung com 7267864 0 07 min BELGI
32. Reset 110 Va Setup and Reset 12 5 Off Timer Setting The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours A This option is only available when Off Timer On Off is set to On 12 5 1 Configuring Off Timer Setting 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to SETUP amp RESET and press 3 8 on the product 3 Press 4 W to move to Off Timer Setting and press 9 on the product The following screen will appear SETUP amp RESET KI E AUTO y v v v v v 4 Press 4 W to configure Off Timer Setting 5 The selected option will be applied 12 Setup and Reset 111 A 12 6 Setup and Reset PC AV Mode Set PC AV Mode to AV The picture size will be enlarged This option is useful when you view a movie K e _ This function does not support Analog mode e Supplied for the wide models only such as 16 9 or 16 10 12 6 1 Configuring PC AV Mode T Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to SETUP amp RESET and press 9 on the product 3 Press A V to move to PC AV Mode and press 2 3 on the product The following screen will appear SETUP amp RESET Reset Lang
33. Reverse Side e The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality e Provided ports may vary depending on the product S19C150F S20C150FL S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S19V325N PLUS SAMSUNG S19C150N S20C150NL S22C150N J Port Description DC 14V Connects to the DC power adapter RGB IN Connect to a PC using the D SUB cable 1 Preparations Preparations S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS DC 14V DVIIN RGB IN E coms Port Description Connects to the DC power adapter Connects to a source device via a DVI cable Connect to a PC using the D SUB cable 1 3 Preparations Installation 1 3 1 Attaching the Stand S19C150N S19C150F S20C150FL S20C150NL S22C150N S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS _ Before assembling the product place the product down on a flat and stable surface so that the screen is facing downwards e _ The exterior may differ depending on the product Insert the stand neck into the Check that the stand neck is Tightly fasten the connecting stand base in the direc
34. UM 02 201 24 18 http www samsung com be Dutch http www samsung com be_fr French BOSNIA 051 331 999 http www samsung com BULGARIA 07001 33 11 share cost tariff http www samsung com bg CROATIA 062 SAMSUNG 062 726 786 http www samsung com hr CYPRUS 8009 4000 only from landline http www samsung com gr Appendix 150 Appendix EUROPE CZECH 800 SAMSUNG 800 726786 http www samsung com Samsung Electronics Czech and Slovak s r o V Parku 2343 24 148 00 Praha 4 DENMARK 70 70 19 70 http www samsung com EIRE 0818 717100 http www samsung com ESTONIA 800 7267 http www samsung com ee FINLAND 030 6227 515 http www samsung com FRANCE 01 48 63 00 00 http www samsung com fr GERMANY 0180 6 SAMSUNG bzw http www samsung com 0180 6 7267864 0 20 Anruf aus dem dt Festnetz aus dem Mobilfunk max 0 60 Anruf GREECE 80111 SAMSUNG 80111 726 http www samsung com gr 7864 only from land line 30 210 6897691 from mobile and land line HUNGARY 06 80 SAMSUNG 726 7864 http www samsung com hu ITALIA 800 SAMSUNG 726 7864 http www samsung com LATVIA 8000 7267 http www samsung com lv LITHUANIA 8 800 77777 http www samsung com lt LUXEMBURG 261 03 710 http www samsung com MONTENEGRO 020 405 888 http www samsung com NETHERLANDS 0900 SAMSUNG http www samsung com 0900 7267864 0 10 Min NORWAY
35. V to move to the option you want and press I 5 The selected option will be applied 10 Setup and Reset 100 11 1 Setup and Reset The functions available may vary depending on the product model Reset Return all the settings for the product to the default factory settings 11 1 1 Initializing Settings Reset T Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press 4 W to move to Reset and press 3 c on the product The following screen will appear SETUP amp RESET Reset Eco Saving Off Timer Key Repeat Time Customized Key Off Off Acceleration HARI Ange 4 BAO v v v Reset all settings 4 Press 4 W to move to the option you want and press a 5 The selected option will be applied 11 Setup and Reset 101 Setup and Reset 11 2 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel A This menu is not available when fa GieBright is in Dynamic Contrast mode 11 2 1 Configuring Eco Saving 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to SETUP amp RESET and press 13 08 on the product 3 Press A
36. and e Custom Lean Back Mode 1 will be applied by default if Custom is selected Press A V to move to the option you want and press H The selected option will be applied 4 Screen Setup 63 4 6 Screen Setup SAMSUNG MAGIC Upscale MacicUpscale function can enhance the layers of the picture details and the vividness of the picture WZ gt The function has more obvious effects on low resolution pictures e This menu is not available when Ma GicBright is in Cinema or Dynamic Contrast mode 4 6 1 Configuring SAMSUNG MAGIC Upscale 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press 13 3 on the product 3 Press 4 W to move to SY SUpscale and press O C on the product MAGIC The following screen will appear Comparing with Mode1 Mode2 has a stronger effect 4 Press M V to move to the option you want and press 5 0 5 The selected option will be applied 4 7 Screen Setup Image Size Change the picture size 4 74 Changing the Image Size 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to PICTURE and press 17 c on the product Press A V to move to Image Size and press H C on the product The following scre
37. anel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may be brighter or darker on the LCD panel This does not affect product performance Specifications 16 4 General S19C325N PLUS S19G325N PLUS Model Name S19C325N PLUS S19G325N PLUS Panel Size 18 5 Inches 47 cm Display area 409 8 mm H x 230 4 mm V 16 1 Inches H x 9 1 Inches V Pixel Pitch 0 300 mm H x 0 300 mm V 0 012 Inches H x 0 012 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7M Resolution Optimum 1366 x 768 60 Hz Resolution Maximum 1366 x 768 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 85 MHz Analog Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable Dimensions Without 445 x 273 x53 mm 453 x 284 x 49 mm EDD jean 17 5 x 10 7 x 2 1 Inches 17 8 x 11 2 x 1 9 Inches Weare With Stand 445 x 348 x 177 mm 2 1 kg 453 x 353 x 193 mm 2 1 kg 17 5 x 13 7 x 7 0 Inches 4 6 los 17 8 x 13 9 x 7 6 Inches 4 6 lbs VESA Mounting Interface 75mm x 75
38. ar power is measured with the test method in the current Energy Star Standard e To reduce the power consumption to O watts turn off the power switch on the back of the product or disconnect the power cable Be sure to disconnect the power cable when you will not be using the product for an extended period of time To reduce the power consumption to O watts when the power switch is not available disconnect the power cable 16 Specifications 145 Specifications 16 10 Standard Signal Mode Table N e This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel Therefore a resolution other than the specified resolution may degrade the picture quality To avoid this it is recommended that you select the optimum resolution specified for the screen size of your product e _ Check the frequency when you exchange a CDT monitor connected to a PC for an LCD monitor If the LCD monitor does not support 85Hz change the vertical frequency to 60Hz using the CDT monitor before you exchange it with the LCD monitor If a signal that belongs to the following standard signal modes is transmitted from your PC the screen will automatically be adjusted If the signal transmitted from the PC does not belong to the standard signal modes the screen may be blank even though the power LED turns on In such a case change the settings according to the following table by referring
39. arance and Themes Display Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows ME 2000 Go to Control Panel Display Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows Vista Go to Control Panel gt Appearance and Personalization Personalization Display Settings gt Advanced Settings Monitor and adjust Refresh rate under Monitor settings Windows 7 Go to Control Panel gt Appearance and Personalization Display Screen Resolution gt Advanced settings Monitor and adjust Refresh rate under Monitor settings Windows 8 Go to Settings Control Panel Appearance and Personalization Display gt Screen Resolution gt Advanced settings Monitor and adjust Refresh rate under Monitor settings 15 Troubleshooting Guide Troubleshooting Guide Question Answer How can change the resolution Windows XP Go to Control Panel gt Appearance and Themes Display Settings and adjust the resolution Windows ME 2000 Go to Control Panel Display Settings and adjust the resolution Windows Vista Go to Control Panel gt Appearance and Personalization Personalize gt Display Settings and adjust the resolution Windows 7 Go to Control Panel gt Appearance and Personalization Display gt Adjust Resolution and adjust the resolution Windows 8 Go to Se
40. arts or entirety without the authorization of Samsung Electronics is prohibited Microsoft and Windows are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of the Video Electronics Standards Association e An administration fee may be charged if either o a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual o b you bring the unit to a repair centre and there is no defect in the product i e where you have failed to read this user manual e The amount of such administration charge will be advised to you before any work or home visit is carried out Icons used in this manual PE The following images are for reference only Real life situations may A differ from what is shown in the images Before Using the Product Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched Take the following steps when cleaning E 1 Power off the monitor and computer 2 Disconnect the power cord from the monitor 4 Hold the power cable by the plug and do not touch the cable with wet we hands Otherwise an electric shock may result 3 Wipe the monitor with a clean soft and dry cloth e Do not apply a cleaning agent that contains alcohol solvent or surfactant to the monitor e Do not spray water or dete
41. ce a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product faces downwards While holding the stand neck with one hand pound the other fisted hand down onto the top of the stand base in the direction of the arrow to detach the stand base Turn the connecting screw at the bottom of the stand base to separate it Remove the stand neck from the stand base by pulling it in the direction of the arrow as shown in the figure Preparations 1 3 4 Removing the Stand S19V325N PLUS S20V325B PLUS K The exterior may differ depending on the product Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product faces downwards While holding the stand neck with one hand pound the other fisted hand down onto the top of the stand base in the direction of the arrow to detach the stand base Preparations 1 3 5 Installing a Wall mount Kit or Desktop Stand S19C150F S20C150FL S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S19V325N PLUS Q Attach the wall mount kit or desktop stand here O Bracket sold separately Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding parts on the wall mount kit or desktop stand you want to attach A Wg Notes es Using a screw longer than the standard length can dama
42. ct The following screen will appear MG Demo Full Intelligent e Off Disable fr GieColor e Demo Compare normal screen mode with Acc Color mode e Full Obtain a vivid picture quality for all areas including the flesh colors in the picture e Intelligent Improve the chroma for all areas except the flesh colors in the picture 4 Press 4 W to move to the option you want and press a c 5 The selected option will be applied 7 Configuring Tint 81 7 2 Configuring Tint Red Adjust the value of the color red in the picture Range 0 100 A higher value will increase the intensity of the color Wg This menu is not available when fen GicColor is in Full or Intelligent mode a 7 2 1 Configuring Red 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press H C on the product 3 Press 4 W to move to Red and press f7 c on the product The following screen will appear La AUTO O v v v v v v 4 Adjust the Red using the A V buttons 5 The selected option will be applied 7 Configuring Tint 82 Configuring Tint 7 3 Green Adjust the value of the color green in the picture Range 0 100 A higher value will increase the intensity of the color SAMSUNG K This menu is not available when MAGiceolor is in Full or Intelligent mode 7 3 1 Co
43. cted option will be applied 6 Configuring Tint 6 5 Configuring Tint Gamma Adjust the mid range brightness Gamma of the picture 6 5 1 Configuring Gamma 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A V to move to COLOR and press 9 on the product 3 Press 4 W to move to Gamma and press 9 on the product The following screen will appear Mode1 Mode2 Mode3 4 iv 4 KI AUTO v v v v v v 4 Press M V to move to the option you want and press a c 5 The selected option will be applied 6 Configuring Tint Fy 7 1 Configuring Tint The functions available may vary depending on the product model Adjust the tint of the screen This menu is not available when 7X jcBright is set to Cinema or Dynamic Contrast mode SAMSUNG MAGIC Color MAGIGColor is a new picture quality improvement technology developed independently by Samsung which delivers vivid natural colors without picture quality degradation A This menu is not available when ffa GicAngle is enabled 7 1 1 Configuring SAMSUNG MAGIC Color 7 Press any button on the front of the product to display the Key guide Next press MENU to display the corresponding menu screen 2 Press M V to move to COLOR and press 9 2 on the product 3 Press amp 4 W to move to MaAGicCoOlor and press 17 c on the produ
44. e The appearance of the components and items sold separately may differ from the image shown Components Quick setup guide Warranty card User manual optional Not available in some locations EF DC power adapter D SUB cable optional gt DVI cable optional Stand base Stand neck optional A Components may vary depending on the country 1 Preparations 24 Preparations 1 2 Parts 1 2 1 Frontal Button The functions available may vary depending on the product model IZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality SAMSUNG Function Key Guide MENU SAMSUNG MAGIC BRIGHT Icons Description Open or close the onscreen display OSD menu or return to the parent menu e OSD control lock Maintain the current settings or lock the OSD control to prevent unintended changes to settings e Enable To lock the OSD control press and hold the MENU button for 10 seconds e Disable To unlock the OSD control press and hold the MENU button for more than 10 seconds MENU K Ifthe OSD control is locked e Brightness Contrast and AGI cBright can be adjusted and INFORMATION can be viewed e The Customized Key function can be used by pressing the IC button The Customized Key is available even when the OSD control is l
45. e corresponding menu screen 2 Press A W to move to COLOR and press 9 on the product 3 Press 4 W to move to Gamma and press 9 1 on the product The following screen will appear Mode1 Mode2 Mode3 4 iv 4 AUTO O v v B v v y 4 Press M V to move to the option you want and press a 5 The selected option will be applied 7 Configuring Tint 86 8 1 Coordinating OSD The functions available may vary depending on the product model Language Set the menu language 4 e A change to the language setting will only be applied to the onscreen menu display e It will not be applied to other functions on your PC 8 1 1 Configuring Language 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A V to move to MENU SETTINGS and press t73 c on the product 3 Press A V to move to Language and press 9 amp on the product The following screen will appear MENU SETTINGS Deutsch English Espanol z AUTO v v v 4 Press 4 W to move to the language you want and press 3 c 5 The selected option will be applied 8 2 Coordinating OSD Menu H Position amp Menu V Position Menu H Position Move the menu position to the left or right Menu V Position Move the menu position up or down 8 2 1 Configuring Menu H Position amp Menu V Position 1
46. e you want and press 17 3 2 To hide the information message press MENU A e Ifthe optimum resolution is not selected the message will appear up to three times for a specified time even when the product is turned off and on again e _ The optimum resolution can also be selected in Control Panel on your PC 2 Connecting and Using a Source Device KI Connecting and Using a Source Device 2 3 3 Changing the Resolution Using a PC K e Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality e The picture quality of TFT LCDs may degrade if the optimum resolution is not selected Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution E Control Panel Control Panel File Edit View Favorites Tools He Set Program Access and gt favorites Tools Help Defaults Qe O DB PD senh E roles Connect To Address B gt Control Panel mnie C E 5 2 8 Accessibilty Add Hardware Add or Administrative Adobe Gamma Help and Support Options Remov Tools Ps vB r Folder Options Game Intel R GMA Controllers Driver for All Programs gt TI Run gt onde 9 2 OX 22 Log off Lo irn OFF Keyboard Mail Network Network Setup ae Connections Wizard reen Saver Assmann Setings Drag the moniter icons to march the physical arrangement of your monitors Display LELEL Screen wschdun s
47. el V high 2 0V V low lt 0 8V Maximum Pixel Clock 85 MHz Analog Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable Dimensions Without 445 x 273 x53 mm 445 x 285 8 x 53 mm Wx Hx D Stand 17 5 x 10 7 x 2 1 Inches 17 5 x 11 3 x 2 1 Inches Weight With Stand 445 x 348 x 177 mm 2 1 kg 445 x 347 x 177 mm 2 1 kg 17 5 x 13 7 x 7 0 Inches 4 6 lbs 17 5 x 13 7 x 7 0 Inches 4 6 lbs VESA Mounting Interface 75mm x 75mm 3 0 Inches x 3 0 Inches Specifications Model Name S19H325N PLUS S19R325N PLUS Environmental Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 Yo 95 non condensing Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1ppm may be brighter or darker on the LCD panel This does not affect product p
48. en will appear 1 Auto Wide KI Lv 4 AUTO N ha hd v v v e Auto Display the picture according to the aspect ratio of the input source Wide Display the picture in full screen regardless of the aspect ratio of the input source Press A V to move to the option you want and press I 2 The selected option will be applied 4 8 Screen Setup H Position amp V Position H Position Move the screen to the left or right V Position Move the screen up or down 4 8 1 Configuring H Position amp V Position 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A V to move to PICTURE and press 2 C3 on the product Press MA V to move to H Position or V Position and press Y 2 The following screen will appear KI AUTO v v KA v v Press A W to configure H Position or V Position The selected option will be applied 4 9 Screen Setup Coarse Adjust the screen frequency 4 9 1 Adjusting Coarse 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press Q on the product 3 Press A W to move to Coarse and press 9 2 on the product The following screen will appear La i AUTO v LA v but v v 4 Adju
49. erformance Specifications 16 6 General S19V325N PLUS S20C325B PLUS Model Name S19V325N PLUS S20C325B PLUS Panel Size 18 5 Inches 47 cm 20 Inches 50 cm Display 409 8 mm H x 230 4 mm V 442 8 mm H X 249 08 mm V arca 16 1 Inches H x 9 1 Inches V 17 4 Inches H x 9 8 Inches V Pixel Pitch 0 300 mm H x 0 300 mm V 0 27675 mm H x 0 27675 mm V 0 012 Inches H x 0 012 Inches V 0 011 Inches H x 0 011 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7 M 16 7 M Resolution Optimum 1366 x 768 60 Hz 1600 x 900 60 Hz Resolution Maximum 1366 x 768 60 Hz 1600 x 900 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 85 MHz Analog 136 MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable 15pin to 15pin D sub cable Detachable DVI D to DVI D connector Detachable 445 x 289 x 67 mm 1
50. ervice Center page 149 e Otherwise an electric shock or fire may result Do not put a heavy object toy or sweets on top of the product e The product or heavy objects may fall as children try to reach for the toy or sweets resulting in a serious injury Before Using the Product 18 Before Using the Product During a lightning or thunderstorm power off the product and remove the power cable e An electric shock or fire may result Do not drop objects on the product or apply impact e An electric shock or fire may result Do not move the product by pulling the power cord or any cable e Otherwise the power cable may be damaged and product failure an electric shock or fire may result If a gas leakage is found do not touch the product or power plug Also ventilate the area immediately e Sparks can cause an explosion or fire Do not lift or move the product by the power cord or any cable e Otherwise the power cable may be damaged and product failure an electric shock or fire may result Do not use or keep combustible spray or an inflammable substance near the product e An explosion or fire may result Ensure the vents are not blocked by tablecloths or curtains e Otherwise a fire may result from an increased internal temperature Do not insert a metallic object a chopstick coin hai
51. es or separately sold product unspecified by Samsung e repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co Ltd e remodeling or repairing the product by customer e using it with incorrect voltage or non authorised electrical connections e not following the cautions in User Manual Others e If product fails by natural disaster lightning fire earthquake flood damage etc e f consumable components are all used up Battery Toner Fluorescent lights Head Vibrator Lamp Filter Ribbon etc K If customer requests a service in case the product has no defect service fee may be charged So please read User Manual first Appendix Correct Disposal Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local gove
52. ess using the A V buttons 5 The selected option will be applied Screen Setup 5 2 Contrast Adjust the contrast between the objects and background Range 0 100 A higher value will increase the contrast to make the object appear clearer K This option is not available when fa gicBright is in Cinema or Dynamic Contrast mode 5 2 1 Configuring Contrast 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press a on the product 3 Press 4 W to move to Contrast and press 373 on the product The following screen will appear KI i AUTO amp v v v v v M 4 Adjust the Contrast using the A V buttons 5 The selected option will be applied 5 3 Screen Setup Sharpness Make the outline of objects more clear or blurry Range 0 100 A higher value will make the outline of objects clearer A This option is not available when MagGicBright is in Cinema or Dynamic Contrast mode 5 3 1 Configuring Sharpness 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press t c on the product 3 Press A W to move to Sharpness and press Q C on the product The following screen will appear EI AUTO O v v v v v v 4 Adju
53. ge the internal components of the product The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications Do not use screws that do not comply with the VESA standards Do not attach the wall mount kit or desktop stand using excessive force The product may get damaged or fall and cause personal injury Samsung shall not be held liable for any damage or injury caused by using improper screws or attaching the wall mount kit or desktop stand using excessive force Samsung shall not be held liable for any product damage or personal injury caused by using a wallmount kit other than the one specified or from an attempt to install the wall mount kit on your own To mount the product on a wall ensure you purchase a wall mount kit that can be installed 10cm or farther away from the wall Be sure to use a wall mount kit that complies with the standards To install the monitor using a wall mount disconnect the stand base from the monitor Preparations 1 3 6 Adjusting the Product Tilt I The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality e You can adjust the tilt of your monitor e Hold the lower part of the product and adjust the tilt carefully Preparations 1 3 7 Anti theft Lock An anti theft lock allows you to use the product securely even in public places The l
54. gnal Mode Table the message Not Optimum Mode will appear for a short time 15 1 3 Check the following Installation issue PC mode Issues Solutions The screen keeps switching on and off Check the cable connection between the product and PC and ensure the connectors are locked Refer to 2 2 Connecting and Using a PC Troubleshooting Guide Screen issue Issues The power LED is off The screen will not switch on Solutions Check that the power cable is connected properly Refer to 2 2 Connecting and Using a PC The message Check Signal Cable appears Check that the cable is properly connected to the product Refer to 2 2 Connecting and Using a PC Check that the device connected to the product is powered on Not Optimum Mode is displayed This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product Change the maximum resolution and frequency to suit the product performance referring to Standard Signal Mode Table page 146 The images on the screen look distorted Check the cable connection to the product Refer to 2 2 Connecting and Using a PC The screen is not clear The screen is blurry Adjust Coarse and Fine Remove any accessories video extension cable etc and try again Set the resolution and frequency to the recommended level The screen appears unstable a
55. grams to remove the software Select Yes to start removing MagicTune Wait until a message box appears informing you that the software has been removed completely LE For technical support the FAQ frequently asked questions or information about the software upgrade for MagicTune please visit our website http www samsung com us consumer learningresources Monitor magetune pop intro htmi A Installing the Software 14 2 MultiScreen im MultiScreen MultiScreen enables users to use the monitor by partitioning multiple sections 14 2 1 Installing the Software 7 Insert the installation CD into the CD ROM drive 2 Select the MultiScreen setup program NG If the pop up screen for the software installation does not appear on the main screen find and double click the MultiScreen setup file on the CD ROM 3 When the Installation Wizard appears click Next 4 Complete the remaining software installation steps according to the instructions displayed on the screen NG e _ The software may not work properly if you do not restart the computer after the installation The MultiScreen icon may not appear depending on the computer system and the product specifications e Ifthe shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MultiScreen The MultiScreen installation may be affected by the Graphics Card Motherboard and the Networking Environment Syste
56. he Stand S19V325N PLUS S20V325B PLUS 37 Installing a Wall mount Kit or Desktop Stand S19C150F S20C150FL S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S19V325N PLUS 38 Adjusting the Product Tilt 39 Anti theft Lock CONNECTING AND USING 40 Before Connecting A SOURCE DEVICE IN O Pre connection Checkpoints 41 Connecting and Using a PC 41 Connection Using the D SUB Cable Analogue Type 42 Connection Using the DVI Cable 43 Connection Using an DVI HDMI Cable 43 Connecting the Power 44 Driver Installation 45 Setting Optimum Resolution 46 Changing the Resolution Using a PC SCREEN SETUP 50 Brightness 50 Configuring Brightness 51 Contrast 51 Configuring Contrast 52 Sharpness 52 Configuring Sharpness 53 SAMSUNG MAGIC Bright 53 Configuring SAMSUNG MAGIC Bright Table Of Contents 54 54 55 55 56 56 57 on 58 58 SCREEN SETUP ss 59 60 60 61 61 62 62 63 63 64 64 65 65 66 66 67 67 SAMSUNG MAGIC Upscale Configuring SAMSUNG MAGIC Upscale Image Size Changing the Image Size H Position 4 V Position Configuring H Position amp V Position Coarse Adjusting Coarse Fine Adjusting Fine Brightness Configuring Brightness Contrast Configuring Contrast Sharpness Configuring Sharpness SAMSUNG MAGIC Bright Configuring SAMSUNG MAGIC Bright SAMSUNG MAGIC Angle Configuring SAMSUNG MAGIC Angle SAMSUNG MAGIC Upscale Co
57. hes H x 0 01 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7M Resolution Optimum 1366 x 768 60 Hz 1920 x 1080 60 Hz Resolution Maximum 1366 x 768 60 Hz 1920 x 1080 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 85 MHz Analog 148 MHz Analog Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable Dimensions Without 445 x 273 x 53 mm 512 x311 x53 mm WxH xD Weight Stand 17 5 x 10 7 x 2 1 Inches 20 2 x 12 2 x 2 1 Inches With Stand 445 x 348 x 177 mm 2 15 kg 512 x 385 x 197 mm 3 1 kg 17 5 x 13 7 x 7 0 Inches 4 7 lbs 20 2 x 15 2 x 7 8 Inches 6 8 lbs Environmental Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 96 non condensing Storage Temperature 4 F 118 F 20 C 45 C Humidity 5 95 Yo non condensing 16 Specifications 129 Specifications Model Name S19C150N S22C150N Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the mo
58. ii eee by eeepc ORE Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel Personalization Display Settings and change the resolution 2 Windows Live Messenger Download w Norton AntiVirus Windows DVD Maker Windows Meeting Space gt All Programs Pick a different mouse pointer You can also change how the mouse porter looks during such activities as clicking and selecting Theme Change the there Themes can change a wide range of visual and auditory elements at one time including the appearance of menus icons backgrounds sereen cavers some computer sounds and mouse pointers Display Settings Adjust your monitor revolution which changes the view 10 more or fewer items fit on the screen You can also control monitor flicker refresh rate KKK KHER KEK KKK KKK ERK HK Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution a Remote Desktop Connection wi Microsoft Word 2010 evices and Printe j Fes Administrative Tools gt Wireless Display Manager Backup and Restore xe Microsoft Office Excel 2007 a Color Management he gt o Default P Desktop G fan P en n a E Device Manager airg Devices and Printers a Display Ease of Access Center ee g Ko Control Panel gt All Control Pa
59. installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may be brighter or darker on the LCD panel This does not affect product performance Specifications 16 8 General S20R325B PLUS S20V325B PLUS Model Name S20R325B PLUS S20V325B PLUS Panel Size 20 Inches 50 cm Display area 442 8 mm H X 249 08 mm V 17 4 Inches H x 9 8 Inches V Pixel Pitch 0 27675 mm H x 0 27675 mm V 0 011 Inches H x 0 011 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75Hz Frequency Display Color 16 7M Resolution Optimum 1600 x 900 60 Hz Resolution Maximum 1600 x 900 60 Hz Resolution Input Signal Terminated RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 136 MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin
60. ize Changing the Image Size Menu H Position amp Menu V Position Configuring Menu H Position amp Menu V Position Reset Initializing Settings Reset Table Of Contents 96 Eco Saving 96 Configuring Eco Saving 97 Off Timer 97 Configuring Off Timer 98 Turn Off After 98 Configuring Turn Off After 99 Key Repeat Time 99 Configuring Key Repeat Time 100 Customized Key 100 Configuring Customized Key SETUP AND RESET 101 Reset 101 Initializing Settings Reset 102 Eco Saving 102 Configuring Eco Saving 103 Off Timer 103 Configuring Off Timer 104 Turn Off After 104 Configuring Turn Off After 105 Key Repeat Time 105 Configuring Key Repeat Time 106 Customized Key 106 Configuring Customized Key SETUP AND RESET 107 Reset 107 Initializing Settings Reset 108 Language 108 Configuring Language 109 Eco Saving 109 Configuring Eco Saving Table Of Contents 110 Off Timer On Off 110 Configuring Off Timer On Off 111 Off Timer Setting Wi Configuring Off Timer Setting 112 PC AV Mode a2 Configuring PC AV Mode 113 Key Repeat Time 113 Configuring Key Repeat Time 114 Customized Key 114 Configuring Customized Key 115 Auto Source 115 Configuring Auto Source 116 Display Time 116 Configuring Display Time 117 Menu Transparency 117 Changing Menu Transparency INFORMATION MENU AND 118 INFORMATION OTHERS 118 Displaying INFORMATION 119 Configuring Brightness and Contrast in the I
61. l Pitch 0 27675 mm H x 0 27675 mm V 0 011 Inches H x 0 011 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75Hz Frequency Display Color 16 7M Resolution Optimum 1600 x 900 60 Hz Resolution Maximum 1600 x 900 60 Hz Resolution Input Signal Terminated RGB Analog DVI Digital Visual Interface Compliant Digital RGB 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 136 MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable DVI D to DVI D connector Detachable 486 x 301 x53 mm 479 x 291 x53 mm 19 1 x 11 9 x 2 1 Inches 18 9 x 11 5 x 2 1 Inches Dimensions Without WxHxD Stand Weight With Stand 486 x 370 x 193 mm 2 2 kg 479 x 365 x 177 mm 2 1 kg 19 1 x 14 6 x 7 6 Inches 4 9 lbs 18 9 x 14 4 x 7 0 Inches 4 6 lbs Environmental Operating considerations Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 96 95 non condensing 4 6 Specifications 141 Specifications Model Name S20G325B PLUS S20H325B PLUS Plug and Play This monitor can be
62. l button on the product is pressed the Function Key Guide will be displayed before the onscreen menu opens The guide shows the function of the button pressed To access the onscreen menu when the guide is displayed press the corresponding button again The Function Key Guide may vary depending on the function or product model Refer to the actual product Preparations 1 2 3 Frontal Button The functions available may vary depending on the product model NG The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Function Key Guide MENU SAMSUNG wo EB ee MD Icons Description Open or close the onscreen display OSD menu or return to the parent menu e OSD control lock Maintain the current settings or lock the OSD control to prevent unintended changes to settings e Enable To lock the OSD control press and hold the MENU button for 10 seconds e Disable To unlock the OSD control press and hold the MENU MENU button for more than 10 seconds K Ifthe OSD control is locked e Brightness Contrast and AGI cAngle can be adjusted and INFORMATION can be viewed e The Customized Key function can be used by pressing the Cr button The Customized Key is available even when the OSD control is locked Configure Customized Key and press 4 The following o
63. lay the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 13 08 on the product 3 Press A V to move to Eco Saving and press IQ on the product The following screen will appear SETUP amp RESET 4 iv A ee BUKO v v v v Yy v e 75 Change the monitor power consumption to 75 of the default level e 50 Change the monitor power consumption to 50 of the default level e Off Deactivate the Eco Saving function 4 Press A V to move to the option you want and press 3 8 5 The selected option will be applied 12 Setup and Reset 109 A Setup and Reset 12 4 Off Timer On Off You can set the product to automatically turn off 12 4 1 Configuring Off Timer On Off 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A V to move to SETUP amp RESET and press T C on the product Press A V to move to Off Timer On Off and press H C on the product The following screen will appear SETUP amp RESET KI LY 4 gt ao o bd y v v v v e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically Press A V to move to the option you want and press I 2 The selected option will be applied 12 Setup and
64. lowing screen will appear La i AUTO v LA v but v v 4 Adjust the Coarse using the A W buttons 5 The selected option will be applied 3 Screen Setup 57 3 9 Screen Setup Fine Fine adjust the screen to obtain a vivid picture 3 9 1 Adjusting Fine 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press Q on the product 3 Press M V to move to Fine and press H C on the product The following screen will appear KI AUTO vi Ni v x v v 4 Adjust the Fine using the A W buttons 5 The selected option will be applied 3 Screen Setup 58 4 1 Screen Setup The functions available may vary depending on the product model Configure the screen settings such as brightness Brightness You can adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter K e This menu is not available when Ma GicBright is set to Dynamic Contrast mode e This menu is not available when Eco Saving is enabled 4 1 1 Configuring Brightness 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press a on the product 3 Press A V to move to Brightness a
65. lution and 768 vertical lines vertical resolution E g A resolution of 1920 x 1080 consists of 1920 horizontal pixels horizontal resolution and 1080 vertical lines vertical resolution Plug amp Play The Plug amp Play feature allows the automatic exchange of information between a monitor and PC to produce an optimum display environment The monitor uses VESA DDC international standard to execute Plug amp Play Index A Auto Source 115 B Before Connecting 40 Blue 78 84 Brightness 50 59 69 C Checking the Contents 23 Coarse 57 67 74 Color Tone 79 85 Connecting and Using a PC 41 Connecting the Power 43 Contact SAMSUNG WORLD WIDE 149 Contrast 51 60 70 Copyright 11 Correct Disposal 156 Correct posture to use the product 22 Customized Key 100 106 114 D Display Time 89 116 E Eco Saving 96 102 109 F Fine 58 68 75 G Gamma 80 86 General 129 Green 77 83 Image Size 55 65 92 INFORMATION 118 Installation 33 K Key Repeat Time 99 105 113 L Language 87 108 M MagicTune 120 Menu Transparency 117 MultiScreen 122 O Off Timer 97 103 Off Timer Setting 111 P Parts 25 PowerSaver 145 Q Q amp A 127 R Red 76 82 Requirements Before Contacting Samsung Customer Service Center 124 Reset 95 101 107 Responsibility for the Pay Service Cost to Customers 155 Index S Safety Precautions 14 SAMSUNG MAGIC Angle 63 73 SAMSUNG MAG
66. m Requirements Os e Windows 2000 e Windows XP Home Edition e Windows XP Professional e Windows Vista 32Bit e Windows 7 32Bit e Windows 8 32Bit NG For MultiScreen the operating systems Windows 2000 or later is recommended Installing the Software Hardware e Atleast 32MB of memory e Atleast 60MB of free space on the hard disk drive 14 2 2 Removing the Software Click Start select Settings Control Panel and then double click Add or Remove Programs Select MultiScreen from the program list and click the Add Delete button 15 1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 15 1 1 Testing the Product A Before calling Samsung Customer Service Center test your product as follows If the problem persists contact Samsung Customer Service Center Check if your product is operating normally by using the product test function If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC perform a self diagnosis test 1 Power off both the PC and product 2 Disconnect the cables from the product 3 Power on the product 4 If the message Check Signal Cable appears the product is working normally NG If the screen remains blank check the PC system video controller and cable 15 1 2 Checking the Resolution and Frequency For a mode that exceeds the supported resolution refer to 16 10 Standard Si
67. mm 3 0 Inches x 3 0 Inches Specifications Model Name S19C325N PLUS S19G325N PLUS Environmental Operating Temperature 50 F 104 F 10 C 40 C considerations Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 Yo 95 non condensing Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1ppm may be brighter or darker on the LCD panel This does not affect product performance Specifications 16 5 General S19H325N PLUS S19R325N PLUS Model Name S19H325N PLUS S19R325N PLUS Panel Size 18 5 Inches 47 cm Display area 409 8 mm H x 230 4 mm V 16 1 Inches H x 9 1 Inches V Pixel Pitch 0 300 mm H x 0 300 mm V 0 012 Inches H x 0 012 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7M Resolution Optimum 1366 x 768 60 Hz Resolution Maximum 1366 x 768 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL lev
68. nd press t c on the product The following screen will appear EI AUTO bd v v bud v v 4 Adjust the Brightness using the A V buttons 5 The selected option will be applied 4 2 Screen Setup Contrast Adjust the contrast between the objects and background Range 0 100 A higher value will increase the contrast to make the object appear clearer A This option is not available when fa gicBright is in Cinema or Dynamic Contrast mode 4 2 1 Configuring Contrast 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press aQ on the product 3 Press 4 W to move to Contrast and press 373 on the product The following screen will appear AUTO O v v v v v 4 Adjust the Contrast using the A V buttons 5 The selected option will be applied 4 3 Screen Setup Sharpness Make the outline of objects more clear or blurry Range 0 100 A higher value will make the outline of objects clearer K e This option is not available when MagicBright is in Cinema or Dynamic Contrast mode e This menu is not available when Ma GicUpsceale is in Mode1 or Mode2 4 3 1 Configuring Sharpness 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W t
69. nd shaky There are shadows or ghost images left on the screen Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product Next if required change the settings referring to Standard Signal Mode Table page 146 in this manual and the INFORMATION menu on the product The screen is too bright The screen is too dark Adjust Brightness and Contrast Screen color is inconsistent Change the COLOR settings Refer to Configuring Tint The colors on the screen have a shadow and are distorted Change the COLOR settings Refer to Configuring Tint White does not really look white Change the COLOR settings Refer to Configuring Tint 15 Troubleshooting Guide 125 Troubleshooting Guide Issues Solutions There is no image on the screen and the power The product is operating in power saving mode LED blinks every 0 5 to 1 second Press any key on the keyboard or move the mouse to return to normal operating mode Source device issue Issues Solutions A beeping sound is heard when my PC is booting If a beeping sound is heard when your PC is booting have your PC serviced Troubleshooting Guide 15 2 Q amp A Question How can change the frequency Answer Set the frequency on your graphics card Windows XP Go to Control Panel gt Appe
70. nel Items P Display 6r Seorch Control Ponet 2 Control Panel Home Change the appearance of your displays Make it easier to read what s on your screen Adjust resolution You can change the size of text and other items on your screen by choosing one of these options To temporarily enlarge just part of the screen use the Magnifier Calibrate color tool Change display settings Connect to a projector PAA Adjust ClearType text Set stom et size PD Medium 125 See a s a payan ar prem the MP key ont tap P dx Some items may not tit on your screen If you choose this setting while your display is set to this resolution en Connecting and Using a Source Device Changing the Resolution on Windows 8 Go to Settings Control Panel Display Screen Resolution and change the resolution 2 Connecting and Using a Source Device 49 3 1 Screen Setup The functions available may vary depending on the product model Configure the screen settings such as brightness Brightness You can adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter K e This menu is not available when Ma GicBright is set to Dynamic Contrast mode e This menu is not available when Eco Saving is enabled 3 1 1 Configuring Brightness 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corre
71. nfiguring Green 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press 9 2 on the product 3 Press 4 W to move to Green and press 13 3 on the product The following screen will appear AUTO v v v v 4 Adjust the Green using the A W buttons 5 The selected option will be applied 7 Configuring Tint 83 7 4 Configuring Tint Blue Adjust the value of the color blue in the picture Range 0 100 A higher value will increase the intensity of the color Wg This menu is not available when ya Color is in Full or Intelligent mode a 7 4 1 Configuring Blue 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press H C on the product 3 Press A W to move to Blue and press t c on the product The following screen will appear KI i AUTO v v v v v v 4 Adjust the Blue using the A W buttons 5 The selected option will be applied 7 Configuring Tint 84 1 9 Configuring Tint Color Tone Adjust the general color tone of the picture K e This menu is not available when jn GicColor is in Full or Intelligent mode N e This menu is not available when fA GicAngle is enabled 7 5 1 Configuring the Color Tone
72. nfiguring Off Timer 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to SETUP amp RESET and press II C2 on the product Press A W to move to Off Timer and press T C on the product The following screen will appear SETUP amp RESET KI y A eee lt BUKO v X v v v v e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically Press A V to move to the option you want and press H C The selected option will be applied 10 Setup and Reset y Setup and Reset 10 4 Turn Off After The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours A This option is only available when Off Timer is set to On 10 4 1 Configuring Turn Off After 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 13 8 on the product 3 Press M V to move to Turn Off After and press on the product The following screen will appear SETUP amp RESET KI AUTO hd y v N v v 4 Press A to configure Turn Off After 5 The selected option will be applied 10 Setup and Reset 98
73. nfiguring SAMSUNG MAGIC Upscale Image Size Changing the Image Size H Position 4 V Position Configuring H Position amp V Position Coarse Adjusting Coarse Table Of Contents 68 Fine 68 Adjusting Fine SCREEN SETUP 69 Brightness 69 Configuring Brightness 70 Contrast 70 Configuring Contrast 71 Sharpness 71 Configuring Sharpness 72 SAMSUNG MAGIC Bright U2 Configuring SAMSUNG MAGIC Bright 73 SAMSUNG MAGIC Angle 13 Configuring SAMSUNG MAGIC Angle 74 Coarse 74 Adjusting Coarse 75 Fine Us Adjusting Fine CONFIGURING TINT 76 Red 76 Configuring Red 77 Green Ut Configuring Green 78 Blue 78 Configuring Blue 79 Color Tone 79 Configuring the Color Tone Settings 80 Gamma 80 Configuring Gamma CONFIGURING TINT si SAMSUNG MAGIC Color 81 Configuring SAMSUNG MAGIC Color Table Of Contents COORDINATING OSD COORDINATING OSD SETUP AND RESET 82 82 83 83 84 84 85 85 86 86 87 88 88 89 89 90 90 91 92 92 94 94 95 95 Red Configuring Red Green Configuring Green Blue Configuring Blue Color Tone Configuring the Color Tone Settings Gamma Configuring Gamma Language Configuring Language Menu H Position amp Menu V Position Configuring Menu H Position amp Menu V Position Display Time Configuring Display Time Transparency Changing Transparency H Position amp V Position Configuring H Position amp V Position Image S
74. nitial Screen INSTALLING THE 120 MagicTune SOFTWARE 120 What is MagicTune 120 Installing the Software 121 Removing the Software 122 MultiScreen 122 Installing the Software 123 Removing the Software Table Of Contents TROUBLESHOOTING 124 Requirements Before Contacting GUIDE Samsung Customer Service Center Testing the Product 124 Checking the Resolution and Frequency 124 Check the following 127 Q amp A SPECIFICATIONS 129 General S19C150N S22C150N 131 General S19C150F S20C150FL 133 General S20C150NL 135 General S19C325N PLUS S19G325N PLUS 137 General S19H325N PLUS S19R325N PLUS 139 General S19V325N PLUS S20C325B PLUS 141 General S20G325B PLUS S20H325B PLUS 143 General S20R325B PLUS S20V325B PLUS 145 PowerSaver 146 Standard Signal Mode Table APPENDIX 149 Contact SAMSUNG WORLD WIDE 155 Responsibility for the Pay Service Cost to Customers 55 Not a product defect 155 A Product damage caused by customer s fault 150 Others Table Of Contents 156 156 157 INDEX Correct Disposal Correct Disposal of This Product Waste Electrical amp Electronic Equipment Terminology Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality 2013 Samsung Electronics Samsung Electronics owns the copyright for this manual Use or reproduction of this manual in p
75. nitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1ppm may be brighter or darker on the LCD panel This does not affect product performance Specifications 16 2 General S19C150F S20C150FL Model Name S19C150F S20C150FL Panel Size 18 5 Inches 47 cm 19 5 Inches 49 cm Display area 409 8 mm H x 230 4 mm V 432 mm H x 239 76 mm V 16 1 Inches H x 9 1 Inches V 17 0 Inches H x 9 4 Inches V Pixel Pitch 0 300 mm H x 0 300 mm V 0 27 mm H x 0 27 mm V 0 012 Inches H x 0 012 Inches V 0 01 Inches H x 0 01 Inches V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7M Resolution Optimum 1366 x 768 60 Hz 1600 x 900 60 Hz Resolution Maximum 1366 x 768 60 Hz 1600 x 900 60 Hz Resolution Input Signal Terminated RGB Analog 0 7 Vp p 5 separate H V sync Composite SOG TTL level V high 2 0V V low lt 0 8V Maximum Pixel Clock 85 MHz Analog 136 MHz Analog Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors 15pin to 15pin D sub cable Detachable
76. njured e Tilting the product excessively may cause it to fall and result in personal injury Do not place heavy objects on the product e Product failure or personal injure may result Before Using the Product Correct posture to use the product Use the product in the correct posture as follows e _ Straighten your back e Allow a distance of 45 to 50 cm between your eye and the screen and look slightly downward at the screen Keep your eyes directly in front of the screen e Adjust the angle so light does not reflect on the screen e Keep your forearms perpendicular to your upper arms and level with the back of your hands e Keep your elbows at about a right angle e Adjust the height of the product so you can keep your knees bent at 90 degrees or more your heels attached to the floor and your arms lower than your heart 1 1 Preparations Checking the Contents 1 1 1 Removing the Packaging 1 Open the packaging box Be careful not to damage the product when you open the packaging with a sharp instrument 7 Remove the styrofoam from the product Check the components and remove the styrofoam and plastic bag NG This image is for reference only Store the box in a dry area so that it can be used when moving the product in the future Preparations 1 1 2 Checking the Components K e Contact the dealer from whom you purchased the product if any item is missing
77. not connect the power cable before connecting all other cables Ensure you connect a source device first before connecting the power cable SAMSUNG 7 Connect the DVI cable to the DVI IN port on the back of the product and the DVI port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC For details refer to 2 3 Connecting the Power 3 Press O to change the input source to DVI A Provided ports may vary depending on the product 2 3 Connecting and Using a Source Device 2 2 3 Connection Using an DVI HDMI Cable S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS WZ Do not connect the power cable before connecting all other cables Ensure you connect a source device first before connecting the power cable T Connect the HDMI DVI cable to the DVI IN port on the back of the product and the HDMI port on the PC 2 Connect the DC power adapter to the product and a power socket Next turn on the power switch on the PC For details refer to 2 3 Connecting the Power 3 Press O to change the input source to DVI A Provided ports may vary depending on the product Connecting the Power e _ Connect the power adapter to DC 14V jack on the rear of the product Connect the power cable to the DC power adapter Next connect the DC power adapter to the product Plug in the power cable to the
78. o move to PICTURE and press t c on the product 3 Press 4 W to move to Sharpness and press t c on the product The following screen will appear Ul AUTO O v v v v v v 4 Adjust the Sharpness using the A V buttons 5 The selected option will be applied 4 4 Screen Setup SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used IZ This menu is not available when Eco Saving is enabled You can customize the brightness to suit your preferences 4 4 1 Configuring SAMSUNG MAGIC Bright 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press 3 c on the product 3 Press A V to move to MaGiceright and press 13 c on the product The following screen will appear Custom Standard Game Cinema Dynamic Contrast 4 v 4 AUTO O v v bo y v v e Custom Customize the contrast and brightness as required e Standard Obtain a picture quality suitable for editing documents or using Internet e Game Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements e Cinema Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content e Dynamic Contrast Obtain balanced brightness through automatic contras
79. ocation go to our website www samsung com recyclingdirect or call 877 278 0799 16 Specifications 144 16 9 A Specifications PowerSaver The power saving function of this product reduces power consumption by switching off the screen and controlling the power LED status if the product is not used for a specified period of time The power is not turned off in power saving mode To switch the screen back on press any key on the keyboard or move the mouse Power saving mode functions only when the product is connected to a PC that has a power saving function PowerSaver Energy cto Power saving mode Poweron Power Consumption 9 Power button Power Indicator On Blinking Off Power Consumption S19C150N S19C150F S19C325N PLUS S19G325N PLUS 13W Typical 0 3 W Typical 0 3 W S19H325N PLUS S19R325N PLUS S19V325N PLUS Power Consumption S20C150NL 16W Typical 0 3 W Typical 0 3 W S20C150FL Power Consumption 23W Typical 0 3 W Typical 0 3 W S22C150N Power Consumption S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS 30W Typical 0 3 W Typical 0 3 W IZ gt The power consumption level can vary in different operating conditions or when settings are changed S C150 Model Power saving mode Power off Power button Max 0 45 watts e ENERGY STAR is a US registered mark of the United States Environmental Protection Agency Energy St
80. ocked Configure Customized Key and press The following options will be enabled Ei MAc cBright Eco Saving Image Size 4 To configure Customized Key go to SETUP 4 RESET Customized Key and select the mode you want 1 Preparations FIT Preparations Icons Description Move to the upper or lower menu or adjust the value for an option on the A V OSD menu bog Use this button to control the brightness and contrast of the screen owe Confirm a menu selection Press the AUTO button to automatically adjust the screen settings AUTO K Changing the resolution in Display Properties will activate the Auto Adjustment function amp Turn the screen on or off Function Key Guide When a control button on the product is pressed the Function Key Guide will be displayed before the onscreen menu opens The guide shows the function of the button pressed To access the onscreen menu when the guide is displayed press the corresponding button again The Function Key Guide may vary depending on the function or product model Refer to the actual product Preparations 1 2 2 Frontal Button The functions available may vary depending on the product model WZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Function Key Guide MENU NASON nce SAMSUNG
81. ocking device shape and locking method depend on the manufacturer Refer to the user guide provided with your anti theft locking device for details The lock device is sold separately WZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality To lock an anti theft locking device 1 2 3 A R Fix the cable of your anti theft locking device to a heavy object such as a desk Put one end of the cable through the loop on the other end Insert the Kensington Lock into the security slot on the back of the display Lock the locking device An anti theft locking device can be purchased separately e _ Refer to the user guide provided with your anti theft locking device for details e Anti theft locking devices can be purchased at electronics retailers or online Connecting and Using a Source Device The exterior may differ depending on the product 2 1 Before Connecting 2 1 1 Pre connection Checkpoints e _ Before connecting a source device read the user manual provided with it The number and locations of ports on source devices may differ from device to device e Do not connect the power cable until all connections are completed Connecting the power cable during connection may damage the product e Check the types of ports at the back of the product you want to connect 2 2 Connecting and Using
82. oduct to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A to move to INFORMATION The current input source frequency and resolution will appear PICTURE y COLOR Ng bd kHz Hz NP lt gt MENU SETTINGS 2 e SETUP amp RESET INFORMATION EXIT v A A The displayed menu items may vary depending on the model 13 INFORMATION Menu and Others 118 A INFORMATION Menu and Others 13 2 Configuring Brightness and Contrast in the Initial Screen Adjust the Brightness Contrast using the X buttons when the initial screen that displays no menu screen is displayed 1 Press any button on the front of the product when no menu screen is displayed to display the Function Key Guide Next press X The following screen will appear Contrast 2 Press the 3 c button to alternate between the Brightness and Contrast settings 3 Adjust the Brightness Contrast using the A V buttons 13 INFORMATION Menu and Others 119 Installing the Software 14 1 MagicTune 14 1 1 What is MagicTune Mag clune MagicTune is a software program that helps with monitor adjustments by providing comprehensive descriptions of monitor functions and easy to understand guidelines You can adjust the product with the mouse and the keyboard without using the operating buttons of the product 14 1 2 Installing the Software 1 Insert
83. of TVs suitable for enjoying video and DVD content e Dynamic Contrast Obtain balanced brightness through automatic contrast adjustment 4 Press M V to move to the option you want and press a c 5 The selected option will be applied 3 5 Screen Setup SAMSUNG MAGIC Upscale MacicUpscale function can enhance the layers of the picture details and the vividness of the picture WZ gt The function has more obvious effects on low resolution pictures e This menu is not available when Ma GicBright is in Cinema or Dynamic Contrast mode 3 5 1 Configuring SAMSUNG MAGIC Upscale Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press 3 8 on the product 3 Press 4 W to move to SY SUpscale and press 17 c on the product MAGIC The following screen will appear Comparing with Mode1 Mode2 has a stronger effect 4 Press A V to move to the option you want and press 13 8 5 The selected option will be applied 3 6 Screen Setup Image Size Change the picture size 3 6 1 Changing the Image Size 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A W to move to PICTURE and press 17 c on the product Press A V to move to Image Size and press H C
84. only available when Off Timer is set to On 11 4 1 Configuring Turn Off After 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 13 08 on the product 3 Press 4 W to move to Turn Off After and press O C on the product The following screen will appear SETUP amp RESET KI AUTO hd y v N v v 4 Press A V to configure Turn Off After 5 The selected option will be applied A For products for the market in Europe the Off Timer is set to automatically activate 4 hours after the product powers on This is done in accordance with power supply regulations If you do not want the timer to activate go to MENU gt SETUP amp RESET and set Off Timer to Off 11 Setup and Reset 104 Setup and Reset 11 5 Key Repeat Time Control the response rate of a button when the button is pressed 11 5 1 Configuring Key Repeat Time 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press 2 3 on the product 3 Press M V to move to Key Repeat Time and press 7 c on the product The following screen will appear SETUP amp RESET Acceleration 1 sec 2 sec No Repeat 4 LY 4 NUO v v v v v v e Acceleration 1 sec or
85. precautions A Warning A serious or fatal injury may result if instructions are not followed Personal injury or damage to properties may result if instructions are AN Caution not followed Activities marked by this symbol are prohibited Instructions marked by this symbol must be followed Before Using the Product EYE Before Using the Product Electricity and Safety A The following images are for reference only Real life situations may differ from what is shown in the images A Warning Do not use a damaged power cord or plug or a loose power socket e An electric shock or fire may result Do not plug many products into the same power socket e Otherwise the socket may overheat and cause a fire Do not touch the power plug with wet hands e Otherwise an electric shock may result Insert the power plug all the way in so it is not loose e An unstable connection may cause a fire Connect the power plug to a grounded power socket type 1 insulated devices only e An electric shock or injury may result Do not bend or pull the power cord with force Do not weigh the power cord down with a heavy object e A damaged power cord may cause an electric shock or fire Do not place the power cord or product near heat sources e An electric shock or fire may result Remove foreign substances such as dust around the plug
86. ptions will be enabled Es MacicAngle mMAc cBright Eco Saving Image Size 14 To configure Customized Key go to SETUP amp RESET Customized Key and select the mode you want 1 Preparations 29 Preparations Icons Description Move to the upper or lower menu or adjust the value for an option on the A V OSD menu xt Use this button to control the brightness and contrast of the screen Confirm a menu selection Pressing the D C button when the OSD menu is not displayed will oe change the input source Analog DVI If you power on the product or change the input source by pressing the T L button a message that shows the changed input source will appear at the top left corner of the screen Press the AUTO button to automatically adjust the screen settings K e Changing the resolution in Display Properties will activate the AUTO i Auto Adjustment function e This function is only available in Analog mode tab Tum the screen on or off Function Key Guide When a control button on the product is pressed the Function Key Guide will be displayed before the onscreen menu opens The guide shows the function of the button pressed To access the onscreen menu when the guide is displayed press the corresponding button again The Function Key Guide may vary depending on the function or product model Refer to the actual product 1 Preparations ET Preparations 1 2 4
87. r pin etc or inflammable object paper match etc into the vent or ports of the product e If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 149 e Product failure an electric shock or fire may result Do not place objects containing liquid vases pots bottles etc or metallic objects on top of the product e If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 149 e Product failure an electric shock or fire may result Before Using the Product ET Before Using the Product A Caution F Ca 3 paa maga Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn in or defective pixels If you are not going to use the product for an extended period of time activate power saving mode or a moving picture screen saver Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time vacation etc e Otherwise a fire may result from accumulated dust overheating an electric shock or electric leakage Use the product at the recommended resolution and frequency e Your eyesight ma
88. rgent directly on the product ER 9 4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the monitor 5 Connect the power cord to the product after cleaning the product 6 Power on the monitor and computer Before Using the Product Securing the Installation Space Ensure some space around the product for ventilation An internal temperature rise may cause fire and damage the product Be sure to allow the amount of space as shown below or greater when installing the product NG The exterior may differ depending on the product 4 3 93 inches 10 cm f 3 98 inches 10cm 1 3 93 inches 10 cm 3 93 inches 10 cm 3 Precautions for storage A Be sure to contact Samsung Customer Service Center page 149 if the inside of the monitor needs cleaning Service fee will be charged Before Using the Product Safety Precautions Caution RISK OF ELECTRIC SHOCK DO NOT OPEN Caution TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK THERE ARE NO USER SERVICEABLE PARTS INSIDE REFER ALL SERVICING TO QUALIFIED PERSONNEL This symbol indicates that high voltage is present inside It is dangerous to make any kind of contact with any internal part of this product N This symbol alerts you that important literature concerning operation and maintenance has been included with this product Symbols for safety
89. rnment office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Appendix Terminology OSD On Screen Display On screen display OSD allows you to customize on screen settings to optimize the picture quality as required You can change the screen brightness tint size and many other settings using menus displayed on the screen Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen Adjusting the brightness brightens the whole screen but adjusting Gamma only brightens the medium brightness Grey scale Scale refers to levels of color intensity that show variations of color change from darker areas to brighter areas on the screen Changes to the screen brightness are expressed with black and white variation and grey scale refers to the medium area between black and white Changing the grey scale through Gamma adjustment will change the medium brightness on the screen Scanning rate Scanning rate or refresh rate refers to the frequency of screen refreshes Screen data is transmitted as it refreshes to display an image although the refreshing is invisible to the naked eye The number of screen refreshes is called scanning rate and is mea
90. sponding menu screen 2 Press amp 4 W to move to PICTURE and press a on the product 3 Press A V to move to Brightness and press t c on the product The following screen will appear EI AUTO b d v v v v v 4 Adjust the Brightness using the A V buttons 5 The selected option will be applied 3 2 Screen Setup Contrast Adjust the contrast between the objects and background Range 0 100 A higher value will increase the contrast to make the object appear clearer This option is not available when AGI Bright is in Cinema or Dynamic Contrast mode 3 2 1 Configuring Contrast 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press aQ on the product 3 Press 4 W to move to Contrast and press 373 on the product The following screen will appear EI AUTO O v v v v v M 4 Adjust the Contrast using the A V buttons 5 The selected option will be applied 3 3 Screen Setup Sharpness Make the outline of objects more clear or blurry Range 0 100 A higher value will make the outline of objects clearer A e This option is not available when MagicBright is in Cinema or Dynamic Contrast mode e This menu is not available when AGjeUpscale is in Mode1 or Mode2 3 3 1 Configuring Sharpness 1 Press any button on the front
91. st the Coarse using the A W buttons 5 The selected option will be applied Screen Setup 4 10 Fine Fine adjust the screen to obtain a vivid picture 4 10 1 Adjusting Fine 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press IQ on the product 3 Press M V to move to Fine and press H C on the product The following screen will appear La i AUTO v LA v but v v 4 Adjust the Fine using the A W buttons 5 The selected option will be applied 5 1 Screen Setup The functions available may vary depending on the product model Configure the screen settings such as brightness Brightness You can adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter K e This menu is not available when Ma GicBright is set to Dynamic Contrast mode e This menu is not available when Eco Saving is enabled 5 1 1 Configuring Brightness 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press Q on the product 3 Press A V to move to Brightness and press 3 c on the product The following screen will appear EI AUTO v v v v v M 4 Adjust the Brightn
92. st the Sharpness using the A W buttons 5 The selected option will be applied 5 Screen Setup 71 5 4 Screen Setup SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used A e This menu is not available when Eco Saving is enabled e This menu is not available when A icAngle is enabled You can customize the brightness to suit your preferences 5 4 1 Configuring SAMSUNG MAGIC Bright 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press Q on the product 3 Press 4 W to move to MAc cBright and press 13 c on the product The following screen will appear Custom Standard Game Cinema Dynamic Contrast v Lv 4 AUTO vi Wi e Custom Customize the contrast and brightness as required e Standard Obtain a picture quality suitable for editing documents or using Internet e Game Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements e Cinema Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content e Dynamic Contrast Obtain balanced brightness through automatic contrast adjustment 4 Press 4 W to move to the option you want and press ce 5 The selected option will be applied
93. sured in Hz A scanning rate of 60Hz means that the screen refreshes 60 times per second The screen scanning rate depends on the performance of the graphics cards in your PC and monitor Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots pixels Pixels are transmitted in horizontal lines which are then arranged vertically to create an image The horizontal frequency is measured in kHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85000 times per second The horizontal frequency is indicated in 85kHz Vertical Frequency One image is made of numerous horizontal lines The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines A vertical frequency of 60 means that an image is transmitted 60 times per second The vertical frequency is also called refresh rate and affects screen flicker Appendix Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen It represents the level of display detail A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time E g A resolution of 1366 x 768 consists of 1366 horizontal pixels horizontal reso
94. t adjustment 4 Press M V to move to the option you want and press a c 5 The selected option will be applied 4 5 Screen Setup SAMSUNG MAGIC Angle MAGIcAngle allows you to configure the settings to obtain the optimum picture quality according to your viewing angle K This option is not available when MA icBright is in Cinema or Dynamic Contrast mode This feature provides the viewing angle brightness and tint to suit your preferences 4 5 1 Configuring SAMSUNG MAGIC Angle 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen Press A V to move to PICTURE and press 17 2 on the product Press 4 V to move to fa gicAngle and press H C on the product The following screen will appear Off Lean Back Mode 1 Lean Back Mode 2 Standing Mode Side Mode Group View Custom KI iv 4 v v v v Off D Select this option to view directly in front of the product e Lean Back Mode 1 Select this option to view from a place slightly lower than the product e Lean Back Mode 2 O Select this option to view from a place lower than Lean Back Mode 1 e Standing Mode Select this option to view from a place higher than the product e Side Mode OF Select this option to view from either side of the product e Group View Select this option for more than one viewer to view from places D
95. t of the screen This menu is not available when 7 X jcBright is set to Cinema or Dynamic Contrast mode Red Adjust the value of the color red in the picture Range 0 100 A higher value will increase the intensity of the color 6 1 1 Configuring Red T Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press M V to move to COLOR and press 9 on the product 3 Press 4 W to move to Red and press C3 on the product The following screen will appear Ea E3 AUTO O v v v x v 4 Adjust the Red using the A W buttons 5 The selected option will be applied 6 Configuring Tint 6 2 Configuring Tint Green Adjust the value of the color green in the picture Range 0 100 A higher value will increase the intensity of the color 6 2 1 Configuring Green 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press 9 2 on the product 3 Press 4 W to move to Green and press 2 c on the product The following screen will appear 4 Adjust the Green using the A W buttons 5 The selected option will be applied 6 Configuring Tint 6 3 Configuring Tint Blue Adjust the value of the color blue in the picture Range O 100 A higher value will increase
96. the installation CD into the CD ROM drive 2 Select the MagicTune setup program I fthe pop up screen for the software installation does not appear on the main screen find and double click the MagicTune setup file on the CD ROM 3 Select the installation language and click Next 4 Complete the remaining software installation steps according to the instructions displayed on the screen Ze The software may not work properly if you do not restart the computer after the installation The MagicTune icon may not appear depending on the computer system and the product specifications e Ifthe shortcut icon does not appear press the F5 key Restrictions and Problems with the Installation MagicTune The installation of MagicTune may be affected by the Graphics Card Motherboard and the Networking Environment System Requirements OS e Windows XP Windows Vista Windows 7 Windows 8 Installing the Software 14 1 3 Removing the Software You can only remove MagicTune through Add or Remove Programs in Windows To remove MagicTune complete the following steps 1 9 mm KR GUN Click Start select Settings and select Control Panel from the menu For Windows XP click Start and select Control Panel from the menu Double click the Add or Remove Programs icon in the Control Panel In the Add Remove window find and select MagicTune so that it is highlighted Click Change or Remove Pro
97. the intensity of the color 6 3 1 Configuring Blue 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to COLOR and press 9 2 on the product 3 Press 4 W to move to Blue and press t c on the product The following screen will appear AUTO v v v 5 4 Adjust the Blue using the A V buttons 5 The selected option will be applied 6 Configuring Tint 6 4 Configuring Tint Color Tone Adjust the general color tone of the picture 6 4 1 Configuring the Color Tone Settings 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to COLOR and press 9 on the product 3 Press M V to move to Color Tone and press Q C on the product The following screen will appear Cool 2 Cool 1 Normal Warm 1 Warm 2 Custom La Lv 4 AUR v v v v v v e Cool 2 Set the color temperature to be cooler than Cool 1 e Cool 1 Set the color temperature to be cooler than Normal mode e Normal Display the standard color tone e Warm 1 Set the color temperature to be warmer than Normal mode e Warm 2 Set the color temperature to be warmer than Warm 1 e Custom Customize the color tone 4 Press A V to move to the option you want and press 13 8 5 The sele
98. the option you want and press a 5 The selected option will be applied 5 6 Screen Setup Coarse Adjust the screen frequency 4 This menu is available in Analog mode only 5 6 1 Adjusting Coarse 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press 4 W to move to PICTURE and press Q on the product 3 Press 4 W to move to Coarse and press Q on the product The following screen will appear KI AUTO v v v v v M 4 Adjust the Coarse using the A V buttons 5 The selected option will be applied 5 Screen Setup 74 5 7 Screen Setup Fine Fine adjust the screen to obtain a vivid picture 4 This menu is available in Analog mode only 5 7 1 Adjusting Fine 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to PICTURE and press Q on the product 3 Press 4 W to move to Fine and press 3 C on the product The following screen will appear po A a GG 0 KI AUTO v v v v v v 4 Adjust the Fine using the A W buttons 5 The selected option will be applied 5 Screen Setup 15 6 1 Configuring Tint The functions available may vary depending on the product model Adjust the tin
99. these signals o This can only be set when the external input is connected through DVI and PC AV Mode is set to AV 4 Press A V to move to the option you want and press a c 5 The selected option will be applied 9 3 Coordinating OSD Menu H Position amp Menu V Position Menu H Position Move the menu position to the left or right Menu V Position Move the menu position up or down 9 3 1 Configuring Menu H Position amp Menu V Position 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SIZE amp POSITION and press 13 on the product 3 Press A V to move to Menu H Position or Menu V Position and press 3 c on the product The following screen will appear KI i AUTO v v v w v v 4 Press A V to configure Menu H Position or Menu V Position 5 The selected option will be applied 9 Coordinating OSD 94 10 1 y Setup and Reset The functions available may vary depending on the product model Reset Return all the settings for the product to the default factory settings 10 1 1 Initializing Settings Reset 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press A W to move to SETUP amp RESET and press t c on the product 3 Press 4 W to move to
100. tion firmly connected screw at the bottom of the shown in the figure stand base Place a soft cloth overthetable Hold the main body of the Caution to protect the product and product with your hand as Do not hold the product upside place the product onto the shown by the figure down only by the stand cloth so na me front of the Push the assembled stand into product is facing downwards the main body in the direction of the arrow as shown in the figure Preparations 1 3 2 Attaching the Stand S19V325N PLUS S20V325B PLUS K e Before assembling the product place the product down on a flat and stable surface so that the screen is facing downwards e _ The exterior may differ depending on the product Place a soft cloth over the table Hold the main body of the Caution to protect the product and product with your hand as Do not hold the product upside place the product onto the shown by the figure down only by the stand cloth so imat Ing front of the Push the assembled stand into product is facing downwards the main body in the direction of the arrow as shown in the figure Preparations 1 3 3 Removing the Stand S19C150N S19C150F S20C150FL S20C150NL S22C150N S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS A The exterior may differ depending on the product Pla
101. to 15pin D sub cable Detachable DVI D to DVI D connector Detachable 478 x 304 x 53 mm 478 x 306 x 67 mm 18 8 x 12 0 x 2 1 Inches 18 8 x 12 0 x 2 6 Inches Dimensions Without WxHxD Stand Weight With Stand 478 x 365 x 177 mm 2 2 kg 478 x 380 x 198 mm 2 4 kg 18 8 x 14 4 x 7 0 Inches 4 9 lbs 18 8 x 15 0 x 7 8 Inches 5 3 lbs Environmental Operating considerations Temperature 50 F 104 F 10 C 40 C Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 96 95 non condensing 4 6 Specifications 143 Specifications Model Name S20R325B PLUS S20V325B PLUS Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may be brighter or darker on the LCD panel This does not affect product performance WZ The above specifications are subject to change without notice to improve quality 4 This device is a Class B digital apparatus USA only Dispose unwanted electronics through an approved recycler To find the nearest recycling l
102. to the graphics card user manual S19C150N S19C150F S19C325N PLUS S19G325N PLUS S19H325N PLUS S19R325N PLUS S19V325N PLUS Resolution blk eaten Bre Hing ae KHz Hz IBM 720 x 400 31 469 70 087 28 322 VESA 640 x 480 31 469 59 940 25 175 MAC 640 x 480 35 000 66 667 30 240 VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 MAC 832 x 624 49 726 74 551 57 284 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1280 x 720 45 000 60 000 74 250 VESA 1366 x 768 47 712 59 790 85 500 16 Specifications 146 Specifications S20C150FL S20C150NL S20C325B PLUS S20G325B PLUS S20H325B PLUS S20R325B PLUS S20V325B PLUS Resolution Hain Paki ant ae m kHz Hz IBM 720 x 400 31 469 70 087 28 322 VESA 640 x 480 31 469 59 940 25 175 MAC 640 x 480 35 000 66 667 30 240 VESA 640 x 480 37 861 72 809 31 500 s s VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 4
103. ttings Control Panel Appearance and Personalization Display Adjust Resolution and adjust the resolution How do set power saving mode Windows XP Set power saving mode in Control Panel gt Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC Windows ME 2000 Set power saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC Windows Vista Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 7 Set power saving mode in Control Panel Appearance and Personalization Personalize gt Screen Saver Settings or BIOS SETUP on the PC Windows 8 Set power saving mode in Settings Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Refer to the user manual for your PC or graphics card for further instructions on adjustment 15 Troubleshooting Guide 128 Specifications 16 1 General S19C150N S22C150N Model Name S19C150N S22C150N Panel Size 18 5 Inches 47 cm 21 5 Inches 54 cm Display area 409 8 mm H x 230 4 mm V 476 64 mm H x 268 11 mm V 16 1 Inches H x 9 1 Inches V 18 8 Inches H x 10 6 Inches V Pixel Pitch 0 300 mm H x 0 300 mm V 0 24825 mm H x 0 24825 mm V 0 012 Inches H x 0 012 Inches V 0 01 Inc
104. u Russian UZBEKISTAN 8 10 800 500 55 500 http www samsung com ASIA PACIFIC AUSTRALIA 1300 362 603 http www samsung com au CHINA 400 810 5858 http www samsung com HONG KONG 852 3698 4698 http www samsung com hk Chinese http www samsung com hk_en English Appendix 152 Appendix ASIA PACIFIC INDIA 1800 3000 8282 http www samsung com in 1800 266 8282 INDONESIA 0800 112 8888 Toll Free http www samsung com id 021 56997777 JAPAN 0120 327 527 http www samsung com MALAYSIA 1800 88 9999 http www samsung com my NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com nz PHILIPPINES 1 800 10 7267864 PLDT http www samsung com ph 1 800 8 7267864 Globe landline and Mobile 02 4222111 Other landline SINGAPORE 1800 SAMSUNG 726 7864 http www samsung com sg TAIWAN 0800 32 9999 http www samsung com tw THAILAND 0 2689 3232 http www samsung com th 1800 29 3232 VIETNAM 1800 588 889 http www samsung com MENA ALGERIA 0800 100 100 http www samsung com n_africa BAHRAIN 8000 4726 http www samsung com ae English http www samsung com ae_ar Arabic EGYPT 08000 726786 http www samsung com IRAN 021 8255 http www samsung com JORDAN 0800 22273 http www samsung com Levant 06 5777444 English KUWAIT 183 2255 183 CALL http www samsung com ae English http www samsung com ae_ar Arabic
105. uage English Eco Saving 1 Off Off Timer On Off On Off Timer Setting 14h PC AV Mode Key Repeat Time Acceleration v La Lv 4 AUTO v v v v v PC AV Mode La ES 4 AUTO 4 Press M V to move to the option you want and press 5 c 5 The selected option will be applied 12 Setup and Reset HA Va Setup and Reset 12 7 Key Repeat Time Control the response rate of a button when the button is pressed 12 7 1 Configuring Key Repeat Time 7 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen 2 Press M V to move to SETUP amp RESET and press 9 3 on the product 3 Press 4 W to move to Key Repeat Time and press 7 c on the product The following screen will appear SETUP amp RESET Acceleration Blisee ser No Repeat 4 LY 4 AUDIO v v v v v v e Acceleration 1 sec or 2 sec can be selected If No Repeat is selected a command responds only once when a button is pressed 4 Press 4 W to move to the option you want and press 3 c 5 The selected option will be applied 12 Setup and Reset 413 Setup and Reset A 12 8 Customized Key You can customize Customized Key as follows 12 8 1 Configuring Customized Key 1 Press any button on the front of the product to display the Function Key Guide Next press MENU to display the corresponding menu screen
106. y deteriorate Do not put DC power adapters together e Otherwise a fire may result Remove the plastic bag from the DC power adapter before you use it e Otherwise a fire may result Do not let water enter the DC power device or get the device wet e An electric shock or fire may result e Avoid using the product outdoors where it can be exposed to rain or snow e Be careful not to get the DC power adapter wet when you wash the floor Do not put the DC power adapter near to any heating apparatus e Otherwise a fire may result Keep the DC power adapter in a well ventilated area Looking at the screen too close for an extended period of time can deteriorate your eyesight Before Using the Product FIT Before Using the Product Do not hold the monitor upside down or move it by holding the stand e The product may fall and break or cause a personal injury Do not use humidifiers or stoves around the product e An electric shock or fire may result Rest your eyes for more than 5 minutes for every 1 hour of product use e Eye fatigue will be relieved Do not touch the screen when the product has been turned on for an extended period of time as it will become hot Store the small accessories used with the product out of reach of children Exercise caution when adjusting the product angle or stand height e Otherwise children s fingers or hands may become stuck and i

Download Pdf Manuals

Related Search

Related Contents

FujiFilm 16112544 Camcorder User Manual    取扱説明 - 日立の家電品  Dell PowerEdge M520 Statement of Volatility  Modificaciones con la instalación en marcha  Hampton Bay 54649141 Instructions / Assembly  LG GSA-4120B User's Manual  none R440151 Use and Care Manual : Free Download, Borrow, and Streaming : Internet Archive  golop d`essoi :  BR2221RH User Manual - Oriental Pacific International  

Copyright © All rights reserved. Failed to retrieve file