Home

PC-586U(PC) Single Board Computer for PICMG User`s Guide

Contents

1. 61 Supervisor User Password esee 62 IDE HDD Auto Detection 4 63 Save amp Exit Setup eee eee REPRE EE 64 Exit Without Saving 64 PC 586U PC User s Manual 43 Chapter 3 BIOS Configuration BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel Cyrix AMD processors in a standard IBM AT compatible I O system The BIOS provides critical low level support for standard devices such as disk drives serial and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately activated Pressing the lt Del gt key immediately allows you to enter the Setup utility If you are a little bit late pressing the lt Del gt key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the Ctrl Alt and Delete keys You can also restart by turning the system Off and back On again The following message will appear on the scree
2. The front bezel of the case has a control panel providing light indication of the computer activities and switches to change the computer status J1 is a 20 pin header that provides interfaces for the following functions Hard Disk Drive LED Reset Switch Turbo LED Connector Green Function ATX Power On Switch Power LED and Keylock Speaker Speaker Pins 1 4 This connector provides an interface to a speaker for audio tone generation An 8 ohm speaker is recommended JL Pin 1 Lr c4 7 ATX Power On Switch Pins 6 and 16 This is an ATX Power Supply On Off Switch that is connected to the power switch on the case 1 10 JI Pin idi 6 Gom CBAR BC Green Function Pins 7 and 17 This connector is for the Green Switch on the control panel which when pressed will force the motherboard immediately into the power saving sleep mode 1 10 JI Pin 17 Sleep 26 PC 586U PC User s Manual Chapter 2 Installations Power LED and Keylock Pins 11 15 The power LED indicates the status of the main power switch The keylock switch when closed will disable the keyboard function 10 Turbo LED Connector Pins 8 and 18 There is the no turbo deturbo function on the CPU card The Turbo LED on the control panel will always be on when attached to this connector 1 10 J1 Pin hun NE SEE MEE eel BEE GL
3. The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the lt Enter gt key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP POWER PNP PCI DUT SAVING ESC Quit V gt lt Select Item F10 Save amp Exit Setup Shift F2 Change Color Change Set Disable Password 62 PC 586U PC User s Manual Chapter 3 BIOS Configuration IDE HDD Auto Detection This option detects the parameters of an IDE hard disk drive and automatically enters them into Standard CMOS Setup screen ROM BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Select Primary Master Option N SKIP N OPTIONS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE 1 Y 0 0 0 0 0 0 0 NORMAL NOTE Some OSes like SCO UNIX must use NORMAL for installation ESC SKIP Up to four IDE drives can be detected with parameters for each appearing in sequence inside a box To accept the displayed entries press the key to skip to the next drive p
4. s Manual Chapter 3 BIOS Configuration OS Select for DRAM gt 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends on certain BIOS calls to access memory The default setting is NON OS 2 Video BIOS Shadow This item allows you to change the Video BIOS location from ROM to RAM Video Shadow will increase the video speed C8000 Shadow DC000 DFFFF Shadow Shadowing a ROM reduces the memory available between 640KB to 1024KB These fields determine whether optional ROM will be copied to RAM or not PC 586U PC User s Manual 51 Chapter 3 BIOS Configuration Chipset Features Setup This Setup menu controls the configuration of the Industrial CPU Card chipset ROM BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC DRAM Timing 70ns System Hardware Monitor System BIOS Cacheable Disabled CPU Warning Temperature 70 C 158 F Video BIOS Cacheable Disabled Current CPU Temperature 37 C 98 F 8 Bit I O Recovery Time 234 16 Bit Recovery Time 1 Current System Temp Memory Hole At 15M 16M Disabled Current CPU Fan Speed PCI 2 1 Compliance Disabled Current Chassis Fan Speed VIO VCORE 12 5 5V 12V ESC Quit V gt Select Item F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults DRAM Timing The DRAM timing is controlled by the DRAM Timing Registe
5. Description The PC 586U PC is a PCI Pentium Industrial CPU card based on Intel s 430TX chipset and is fully designed for harsh industrial environment It features ZIF Socket 7 compatible with various processors from Intel AMD and Cyrix This card accommodates up to 256MB of SDRAM memory and a secondary level 512KB cache The PC 586U PC comes with onboard CPU temperature sensor to protect your processor from overheating The power management feature provides power savings by slowing down the CPU clock turning off the monitor screen and stopping the HDD spindle motor 2 PC 586U PC User s Manual Chapter 1 Introduction Features CPU Speed 90 333MHz Intel P54C P55C MMX Cyrix 6x86 6x86L 6x86MX AMD K5 K6 K6 2 Intel 430TX PCIset Up to 256MB system memory Onboard C amp T PCI VGA controller Onboard Symbios 53C875E Ultra Wide SCSI controller SCSI model Onboard Realtek RTL8139A Ethernet controller 16 level programmable watchdog timer High speed bi directional SPP ECP EPP parallel port Hardware Monitoring Winbond W83781D Specifications Processor Socket ZIF Socket 7 Processor Intel Pentium P55C 90 100 120 133 150 166 200 233 266 Cyrix 6x86 6x86L P150 P166 Cyrix 6x86MX 166 180 200 AMD K5 PR90 PR100 PR133 PR166 AMD K6 166 200 233 AMD K6 2 266 300 333 366 400 PC 586U PC User s Manual Chipset Intel 430TX PClIset with built in PCI EIDE Secondary Cache 512KB P B SRAM Memory Up to 256MB SDRAM EDO
6. This program will automatically create or modify the AUTOEXEC BAT and CONFIG SYS files on your hard drive To complete CD ROM installation you will need MSCDEX EXE pre installed on the hard drive or on a floppy disk MSCDEX EXE is on MS DOS 6 2x Setup Disk Number One Be sure that you know the location and the path of MSCDEX EXE prior to running DOSSETUP EXE The hard drive will need MS DOS 6 xx installed or it will need to be formatted with the s option 1 bootable format prior to running Initio DOSSETUP EXE From the x DOS prompt type DOSSETUP and press enter NOTE x drive letter of floppy drive used After DOSSETUP EXE completes be sure to reboot system so changes take effect 78 PC 586U PC User s Manual Chapter 6 SCSI Driver Installation Guide Installing SCSI Driver for Windows 95 98 Files you need Information script files for installation INIA 100 INF Miniport device driver INIA100 MPD Installation A New Windows 95 installation B Adding INI A100U2W to an existing Windows 95 98 C Updating device driver A New Windows 95 98 installation 1 Run SETUP EXE from the Windows 95 98 CD ROM and follow the directions on the screen 2 After a Windows 95 98 session is established select My Computer Control Panel System Device Manager Other devices PCI SCSI Bus Controller from the Windows 95 98 desktop 3 Click the Driver tab then click the Change Driver tab 4 Double click SCSI controllers
7. Workstation for DOS ODI Client OS 2 ODI Client Server Driver for NetWare 3 11 3 12 4 0 4 1X 5 0 Client 32 for Windows 95 IBM network drivers LAN Server for OS 2 2 3 4 0 Microsoft network drivers Microsoft Network Client for DOS LAN Manager Workstation Server Windows for Workgroups v3 11 Windows NT 3 5 3 51 amp 4 0 Windows 95 amp OSR2 Windows 98 amp Windows 2000 UNIX network drivers SCO UNIX 4 X 5 X Other Network Operating System Information Packet Driver LANtastic 6 0 with NDIS driver The following section describes the installation driver procedure for Windows 98 Windows 2000 Windows 95 Windows NT DOS and Windows for Workgroup To view the procedure of other operating systems execute the help8139 exe in the diskette supplied 70 PC 586U PC User s Manual Chapter 5 LAN Driver Installation Guide Installing LAN Driver for Win98 Windows2000 This section describes the procedure to install Windows 98 and Windows 2000 driver for Realtek RTL8139 PCI Fast Ethernet adapter Before you start with the installation process make sure that your adapter is properly installed in the PCI bus slot Executing Win98 Windows2000 will auto detect your system configuration and find the adapter hardware If Win98 Windows2000 does not prompt that it detects the PCI Ethernet adapter there must be something wrong with the Realtek RTL8139 PCI Fast Ethernet adapter or your system environment 1 When asked to select the driver
8. 6 Hostdata9 8 HostdatalO Hostdatad 9 2 10 12 14 16 18 20 Chapter 2 Installations Signal Name Ground Host data 8 Host data 9 Host data 10 Host data 11 Host data 12 Host data 13 Host data 14 Host data 15 29 Chapter 2 Installations J4 Floppy Drive Connector Signal Name Signal Name Ground RM LC Ground N C oo Ground N C Ground Index co Ground 9 T ap a 5 Parallel Port Connector The following table describes the pin out assignments of this connector PD4 parallel data4 6 PDO parallel data6 8 PD7 parallel data7 9 30 PC 586U PC User s Manual Chapter 2 Installations J7 Ultra Wide SCSI Connector The table below shows the pin out assignments of this 68 pin connector 3 64 3 32 66 SEDATO 34 68 SEDATII 17 18 19 zim 32 n GROUND 6 40 SEDATO L GROUND 8 42 SEDAT 5 8 GROUND 9 43 SEDAT3 A a 8 i 3 3 17 BB 18 EY 19 A 0 1 J7 2 3 4 5 6 60 7 8 9 6 1 2 7 PC 586U PC User s Manual 31 Chapter 2 Installations J8 COMI Serial Port J8 a 10 pin header is an onboard serial ports of the PC 586U PC The following table shows the pin assignments of this connector DTR J9 COM2 Serial Port
9. A and specify the pathname A NDIS2DOS then press Enter Follow the screen instructions to complete the process Simply pressing lt Enter gt for each screen display will select the default options Press lt Enter gt until you reach the display prompting you to reboot the system NN a 74 PC 586U PC User s Manual Chapter 5 LAN Driver Installation Guide Installing Driver for Windows for Workgroups This section describes the procedure to install Microsoft Windows for Workgroups v3 11 driver for REALTEK RTL8139 Fast Ethernet adapter When installing Windows for Workgroups you are prompted for a network driver Select the Unlisted or Updated Network Driver 2 Insert the REALTEK adapter driver disk containing OEMSETUP INF and RTSND DOS files Specify the directory for the driver A WFW311 and select the Adapter driver Select Advanced options and make sure the parameters match the card settings Check keyword EtherID which is provided by RTSND DOS The installation program copies the necessary files and creates PROTOCOL INI for use with the adapter Te Existing Windows for Workgroups Installation 1 Select the Network Setup icon in the Network Group 2 Select the Driver button 3 Select the Add Adapters button 4 Select Unlisted or Updated Network Adapter 5 Insert the adapter driver disk with OEMSETUP INF and RTSND DOS and specify the path A WFW311 6 Select the REALTE
10. Chapter 1 Introduction Introduction This manual is designed to give you information on the PC 586U PC CPU card It is divided into the following sections Checklist eeu Ud hin ie ee ee aa as 2 Description itte ee Re EE ERES IHR 2 Features eiTe iR 3 SpecitiCatioDs ED ten testen Oei ere ie 3 Intellig rice uie died RR 5 Board Dimensions and Layout eee 6 The topics covered in this chapter are as follows Checklist Description Features Specifications Layout of Key Components and Dimensions PC 586U PC User s Manual 1 Chapter 1 Introduction Checklist Please check that your package is complete and contains the items below If you discover damaged or missing items please contact your dealer The PC 586U PC Industrial CPU Card This User s Manual IDE Ribbon Cable Floppy Ribbon Cable 1 Key Board Exchange Cable Mounting Bracket with 1 Serial Port Ribbon Cable and 1 Parallel Port Ribbon Cables Mounting Bracket with 1 Serial Port Ribbon Cable Diskette Containing Intel PCI IDE Driver and Flash Memory Utility Diskette Containing System Monitor e 2 Diskettes Containing C amp T 69000 VGA Driver e 2 Diskettes Containing Realtek RTL8139A LAN Driver 4 Diskettes Containing Symbios 53C875E SCSI Drivers SCSI model only Mounting Bracket with SCSI Ribbon Cable SCSI model only e 1 SCSI Terminator SCSI model only
11. D0000 D3FFF Shadow Disabled Boot Sequence A C SCSI D4000 D7FFF Shadow Disabled Swap Floppy Drive Disabled D8000 DBFFF Shadow Disabled Boot Up Floppy Seek Enabled DC000 DFFFF Shadow Disabled Boot Up Numlock Status Security Option Setup PCI VGA Palette Snoop Disabled OS Select For DRAM gt 64MB Non OS2 ESC Quit V gt Select Item F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning message If this occurs you can either allow the operation to continue or run an anti virus program to locate and remove the problem NOTE Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning If you will run such a program disable the Virus Warning feature CPU Internal Cache External Cache These items allow you to enable speed up memory access or disable the cache function By default these items are Enabled Quick Power On Self Test This choice speeds up the Power On Self Test POST after you power up the system If it is set to Enabled BIOS will skip some items By default this choice is Enabled PC 586U PC User s Manual 49 Chapter 3 BIOS Configuration Boot Sequence This field determines
12. Installations JP9 RS 232C 422 485 COM2 Selection COM2 is selectable for RS 232C RS 422 and RS 485 The following table describes the jumper settings of this connector OM RS 232C RS 422 RS 485 Function 1 2 1 2 Jumper Setting Pin closed All Jumpers Open Jumper Illustration 22 PC 586U PC User s Manual Chapter 2 Installations JP10 Clear CMOS Content JP10 Normal Operation Short Closed Default J15 External Battery Connector This 4 pin connector allows the user to connect an external battery to maintain the information stored in the CMOS RAM in case the built in battery malfunctions The default is set to Internal Battery with a jumper connecting pin 1 and pin 2 1_ 2 Internal Battery GND F lt Internal Battery 2 00 3 1 4 External Battery PC 586U PC User s Manual 23 Chapter 2 Installations Connectors on the PC 586U PC The connectors on the PC 586U PC allows you to connect external devices such as keyboard floppy disk drives hard disk drives printers etc The following table lists the connectors on PC 586U PC and their respective functions Connector Locations on the PC 586U PC 25 Front Bezel 26 J2 Power 28 JP2 IrDA Connector eene 28 J3 J6 EIDE Connectors eee 29 J4 Fl
13. J9 a 10 pin header connector is the onboard COM2 serial port of the PC 50000 01 06 DCD Data carrier detect RXD Receive data TXD Transmit data DSR Data set ready RTS Request to send TR Data terminal ready CTS Clear to send Ring indicator 586U PC The following table shows the pin assignments of this connectors 32 50000 01 06 10 RS D D G D Pinf PC 586U PC User s Manual Chapter 2 Installations J10 External Keyboard Connector 110 Pin Keyboard clock 2 Keyboard data N C J11 CPU Fan Power Connector J11 is a 3 pin header for the CPU fan power connector The fan must be a 12V fan 3523 J12 RJ45 Connector This connector is for the 10 100Mbps Ethernet capability of the CPU card The figure below shows the pin out assignments of this connector and its corresponding input jack TD pin 1 TD pin 2 RD pin 3 RD pin 6 J12 J13 External ATX Power Connector a M J13 Pin Signal Name B i 2 k a o 6 4 Ground 6 SV SB Gtandby 5 PC 586U PC User s Manual 33 Chapter 2 Installations 34 PC 586U PC User s Manual Chapter 2 Installations PS 2 Mouse Connector J14 Pin 4 1 Mouse data 2 NC 3 Groma 5 ee aa N C JP6 External P
14. Method sse 54 Video ee 55 Doze Mode tpe 55 Standby Mode e bee e i 55 Suspend Mode oi IR REDIERE Rd 55 HDD Power 55 Soft Off by eese 55 Resume by 55 PWR On by Modem LAN 55 Reload Global Timer Events eese 56 PNP PCI Configuration eese 57 PNP OS Installed 2 dete tede tease 57 Resources Controlled by eese 57 Reset Configuration Data eene 57 IRQ DMA assigned to eee 57 Used MEM base addr eee 58 Load BIOS Defaults 2 2 ors enhn 59 Load Setup Defaults 59 Integrated Peripherals eee 60 IDE HDD Block Mode eene 60 IDE Primary Master Slave PIO And Secondary Master Slave PIO 60 IDE Primary Master Slave UDMA And Secondary Master Slave UDMA 60 On Chip Primary Secondary PCI IDE 61 USB Keyboard Support ee 61 Onboard FDD Controller eene 61 Onboard Serial Parallel 61 UART Mode Select 61 42 PC 586U PC User s Manual Chapter 3 BIOS Configuration Onboard Parallel
15. ON Lr r adc off off off on N off off off off off off off on on on on on 54 100 54 120 54 133 54 150 54 166 55 166 54 200 P55C 200 off off off on 15 PC 586U PC User s Manual Chapter 2 Installations n Foes 1 2 3 OPEN 1 2 3 OPEN Fea 1 2 3 OPEN 1 2 3 OPEN cega 1 2 3 OPEN cega 1 2 3 OPEN 8 i 455 ff off off off off ff off S1 1 8 off off off off off off off off ON For AMD K5 K6 K6 2 CPU 1234 n off off on Ca 5 5 ga CPU K5 PR100 100MHz K5 PR133 133MHz K5 PR166 116 7MHz 117 K6 166 K6 200 K6 266 K6 2 266 K6 300 K6 2 300 K6 333 K6 2 333 PC 586U PC User s Manual 16 Chapter 2 Installations For Cyrix 6x86 and IDT C6 CPU IN 0 6x86 L P150 120MHz A ON 6x86 L P166 133MHz 6x86MX PR166 6x86MX PR200 6x86MX PR233 6x86MX PR300 IDT C6 180 C6 200 For Intel 55C 0 25u 266MHz ON ON ono SHORT PC 586U PC User s Manual 17 Chapter 2 Installations 2 Display Type Setting The PC 586U PC supports several resolution LCD displa
16. Primary Secondary PCI IDE These fields allow you either to enable or disable the Primary Secondary controller You might choose to disable the controller if you were to add a higher performance or specialized controller USB Keyboard Support This field allows your system to support a USB keyboard Onboard FDD Controller This option allows you to select the onboard FDD port Onboard Serial Parallel Port These fields allow you to select the onboard serial parallel port and its address The default value for these ports are Serial Port 1 3F8 IRQ4 Serial Port 2 2F8 IRQ3 Parallel Port 378H IRQ7 UART Mode Select This field determines the UART 2 mode in your computer The options are Standard HPSIR and ASKIR Onboard Parallel Mode This field allows you to determine parallel port mode function SPP Standard Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port ECP EPP Extended Capabilities Port or Enhanced Parallel Port PC 586U PC User s Manual 61 Chapter 3 BIOS Configuration Supervisor User Password These two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press lt Enter gt The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt
17. Reset Switch Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on Orientation is not required when making a connection to this header 1 ome Hard Disk Drive LED Connector Pins 10 20 This connector connects to the hard drive activity LED on control panel This LED will flash when the HDD is being accessed J1 Pin 1 10 HDD LED PC 586U PC User s Manual 27 Chapter 2 Installations J2 Power Connector When using an AT compatible power supply plug the power supply connectors into J2 Make sure the power supply connectors are connected in the right orientation See the pin assignments below pee Name Name 1 Power Good 4 2v 2 S Ground 3 2 6 Ground JP2 IrDA Connector This connector is used for an IrDA connector for wireless communication JP2 Pin 5V O gt ae uin 28 PC 586U PC User s Manual J3 J6 EIDE Connectors J3 is the primary IDE connector and J6 is the secondary IDE connector Signal Name Reset IDE Host data 7 Host data 6 Host data 5 Host data 4 Host data 3 Host data 2 Host data 1 Host data 0 Ground PC 586U PC User s Manual 1 3 5 7 11 13 15 17 19 DRO 21 Signal Name Pin
18. d SM d Verbose mode provides detail information about driver when driver is initialized Non Verbose mode default Driver assumes that all targets have more than one LUN default Driver assumes that all targets only have LUN 0 Specifies maximum number of tag commands per target No tag command Scan devices only on PCI BUS d DEVICE dd Scan all the devices on the PCI BUS d Target enable mask WORD Default scan all targets Adapter IDs are assigned based on BIOS address and then PCI device address Enable direct access storage device DASD support on target d Disable DASD manager support on target d Enable SCSI manager support on target d Disable SCSI manager support on target d PC 586U PC User s Manual 83 Chapter 6 SCSI Driver Installation Guide This page was intentionally left blank 84 PC 586U PC User s Manual Chapter 7 Intel Bus Master IDE Driver Installation Intel Bus Master IDE Driver Installation This chapter describes the installation procedure for Intel Bus Master IDE Drivers for Windows 95 This chapter contains the following sections System Requirements eese nnne Installing the Software eese 87 PC 586U PC User s Manual 85 Chapter 7 Intel Bus Master IDE Driver Installation System Requirements This section describes system requirements for the PIIX Bus Master IDE Device Driver for Windows 95 This driver has be
19. field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA For EGA VGA SEGA SVGA or PGA monitor adapters default CGA 40 Power up in 40 column mode CGA 80 Power up in 80 column mode MONO For Hercules or MDA includes high resolution monochrome adapters Halt On This field determines whether the system will halt if an error is detected during power up No errors The system boot will not be halted for any error that may be detected default All errors Whenever the BIOS detects a non fatal error the system will be halted and you will be prompted All But Keyboard The system boot will not be halted for a keyboard error it will stop for all other errors All But Diskette system boot will not be halted for a disk error it will stop for all other errors All But Disk Key The system boot will not be halted for a keyboard or disk error it will stop for all other errors 48 PC 586U PC User s Manual Chapter 3 BIOS Configuration BIOS Features Setup This section allows you to configure and improve your system and allows you to set up some system features according to your preference ROM PCI ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disabled Video BIOS Shadow Enabled CPU Internal Cache Enabled C8000 CBFFF Shadow Disabled External Cache Enabled CC000 CFFFF Shadow Disabled Quick Power On Self Test Disabled
20. jumpers for the CPU type and speed are correct NOTE Ensure that the CPU heat sink and the CPU top surface are in total contact to avoid CPU overheating problem that would cause your system to hang or be unstable 8 PC 586U PC User s Manual Chapter 2 Installations Memory Installation The PC 586U PC Industrial CPU Card supports two 168 pin DIMM sockets for a maximum total memory of 256MB The DRAMs 3 3Volts for the DIMM sockets can be 8MB 16MB 32MB 64MB 128 and 256MB in EDO and SDRAM types When populating the DIMM sockets either of the DIMM sockets can be populated first DIMMI 8MB 8MB 16MB 32MB 6MB 128MB 128MB 136MB 16MB 32MB 64MB 128MB 144MB 32MB 64MB 96MB 128MB 64MB 64MB 128MB 128MB 128MB 256MB 256MB 256MB 256MB_ PC 586U PC User s Manual 9 Chapter 2 Installations Jumpers on the PC 586U PC The jumpers on the PC 586U PC allow you to configure your CPU card according to the needs of your applications If you have doubts about the best jumper configuration for your needs contact your dealer or sales representative The following table lists the connectors on PC 586U PC and their respective functions Jumper Locations the 5860 11 1 Bus Speed Multiplier Setting 12 S3 1 4 JP7 JP4 CPU Voltag
21. onboard hardware thermal sensor monitors CPU temperature changes and prevents the CPU from overheating Alert is sounded through the speaker and CPU speed slows down when the temperature exceeds the temperature set in the BIOS until the temperature falls below a safe level By default this field is set to 70 C 158 Temperature Fan Speeds Voltages These read only fields show the current CPU temperature speeds in RPM revolution per minute for the CPU fan and chassis fan and current voltages in the voltage regulators and power supply as monitored by the hardware monitoring IC PC 586U PC User s Manual 53 Chapter 3 BIOS Configuration Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn off video display after a period of inactivity ROM BIOS 2 591 29 POWER MANAGEMENT SETUP AWARD SOFTWARE INC Power Management Disabled PM Control by APM Yes Video Off Method DPMS Video Off After Suspend Doze Mode Disabled Standby Mode Disabled Suspend Mode Disabled HDD Power Down Disabled Soft off by PWR BTTN Instant off PWR On by Modem LAN Enabled Resume by Alarm Disabled Power Management Reload Global Timer Events IRQS 3 7 9 15 NMI Enabled Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled Floppy Disk Disabled Serial Por
22. speed while all other devices still operate at full speed Standby Mode When enabled and after the set time of system inactivity the fixed disk drive and the video would be shut off while all other devices still operate at full speed Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWR BTTN This field defines the power off mode when using an ATX power supply The Instant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power button is pressed for more than four seconds or places the system in a very low power usage state with only enough circuitry receiving power to detect power button activity The default value is Instant Off Resume by Alarm This allows the system to be turned on automatically through the timer set in the BIOS to make the system more scheduleable By default this field is set to Disabled PWR On by Modem LAN This allows the system to be powered on through a modem or network By default this field is set to Disabled PC 586U PC User s Manual 55 Chapter 3 BIOS Configuration Reload Global Timer Events This section determines the reloading of the timers after entering the Full On You can en
23. then click the Have Disk button 5 At the prompt type in A win95 insert Initio INI A100U2W driver disk 1 and click the OK button 6 Select Initio INI A100U2W Host Adapter click the OK button Windows 95 will copy INIA100 MPD to your hard disk Reboot to complete the driver installation B Adding INI A100U2W to an existing Windows 95 1 Install the Initio hardware as described in the User Manual User Guide Windows 95 will detect the presence of a new hardware 2 When Windows 95 displays the following New Hardware Found PCI SCSI Bus Controller Select which driver you want to install for your new hardware Driver from disk provided by hardware manufacture OK Cancel Help Click OK PC 586U PC User s Manual 79 Chapter 6 SCSI Driver Installation Guide 3 Windows 95 will then display the following Install From Disk Insert the manufacturer s installation disk into the drive selected and then click OK Copy manufacturer s files from A WIN95 Insert the Initio disk 1 into drive A and Click OK Windows 95 will interpret INIA100 INF script files and load INIA100 MPD driver to win95 system iosubsys directory 4 Windows 95 will then display the following System Settings Changed To finish setting up your new hardware you must restart your computer Do you want to restart your computer now Yes No Remove the diskette from drive A and Click Yes C Up
24. x 1024 256 colors resolution on SVGA 2MB memory 68 pin connector for LCD panel 1280 x 1024 resolution LCD panel supports monochrome color STN TFT EL Simultaneous VGA and panel display 4 PC 586U PC User s Manual Chapter 1 Introduction e LAN Realtek RTL8139A Ethernet controller supporting 10Mb s and 100Mb s N way auto negotiation operation e SCSI Symbios 53C875E Ultra Wide SCSI controller for data transfer rate of up to 40MB s e SDD One socket for M systems Disk on chip is available Up to 144Mbyte Environmental and Mechanical Power Supply 5A typ 5V MMX 266 200mA typ 12V Temperature 0 C to 60 C Humidity 20 to 90 No condensation Suspend dust Not excessive Corrosive gas Must not be present Dimensions 338mm x 122mm Weight 450g Intelligence CPU Slow Down When system overheat is detected CPU slows down to prevent CPU damage The CPU speed is restored when temperature falls to a safe level System overheat is usually caused by malfunctioning of the CPU or system fan Temperature Monitoring and Alert A sensor for the CPU temperature on the PC 586U PC monitors the CPU temperature and alerts the user through the speaker when temperature exceeds the safe heat level PC 586U PC User s Manual 5 Chapter 1 Introduction Board Dimensions and Layout 4 800 121 92cm 4 600 116 84cm 3 522 89 46cm 2 855 72 50cm 2 330 59 17 1336 33 93cm 0 361 9 1
25. you want to install select Driver from disk provided by hardware manufacturer 2 Insert the Realtek RTL8139 driver disk into drive A and specify the setup file pathname AX 3 Win98 Windows2000 will appear with a message to insert Win98 Win2000 system disk to complete setup 4 Win98 Windows2000 will finish other installation procedure automatically and ask you to restart the system PC 586U PC User s Manual 71 Chapter 5 LAN Driver Installation Guide Installing LAN Driver for Windows 95 This section describes the procedure to install Windows 95 driver for Realtek RTL8139 PCI Fast Ethernet adapter Before you start with the installation process make sure that your adapter is properly installed in the PCI bus slot Executing Windows 95 will auto detect your system configuration and find the adapter hardware If Win95 does not prompt that it detects the PCI Ethernet adapter there must be something wrong with the RTL8139 PCI Fast Ethernet adapter or your system environment 1 When asked to select the driver you want to install select Driver from disk provided by hardware manufacturer 2 Insert the Realtek RTL8139 driver disk into drive A and specify the setup file pathname AX 3 Windows 95 will appear with a message to insert Windows 95 system disk to complete setup 5 Windows 95 will finish other installation procedure automatically and ask you to restart the system 72 PC 586U PC User s Manual Chapter 5 LA
26. 1 11 06
27. 8cm 13 415 340 74c m1 13317 338 25cm 13 191 1335 05 12 575 319 41cm 12 425 315 60cm 12 330 131318 13 376 339 75cm 13 317 13 117 333 17cm _2 9235 1234 57 9 025 229 24cn 7135 181 23 6 640 168 66cm 4 166 105 82cm 2092 10394 1 3 521 89 43cm 3196 8118 0 300 7622 0 200 5 08cn1 0 0000 0 0000 0 0000 4 800 121 92cm 4 600 116 84cm 6 PC 586U PC User s Manual Chapter 2 Installations Installations This chapter provides information on how to use the jumpers and connectors on the PC 586U PC in order to set up a workable system The topics covered are CPU Installation erre ERR Her 8 Memory Installation eese nennen 9 Jumpers on the 5860 10 Connectors on the 5860 24 Watchdog Timer Configuration eene 39 PC 586U PC User s Manual 7 Chapter 2 Installations CPU Installation The PC 586U PC Industrial CPU Card supports a ZIF processor socket for Pentium level processors Unlike PGA sockets ZIF Zero Insertion Force sockets come with a lever to secure the processor Make sure the notch on the corner of the CPU corresponds with the notch on the inside of the socket After you have installed the processor into the ZIF socket check if the
28. D 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Tel 81 6 6477 5219 Fax 81 6 6477 1692 E mail intsales osaka contec co jp CONTEC MICROELECTRONICS U S A INC 744 South Hillview Drive Milpitas CA 95035 U S A Tel 1 408 719 8200 Fax 1 408 719 6750 E mail tech_support contecusa com CONTEC MICROELECTRONICS EUROPE B V Binnenweg 4 2132 CT Hoofddorp The Netherlands Tel 31 23 567 3030 Fax 31 23 567 3035 E mail tech support conteceu nl HYOJIN CONTEC Co LTD KI IM Bldg 399 Shindolim Dong Kuro ku Seoul 152 070 Korea Tel 82 2 2636 4277 8 Fax 82 2 2636 4279 E mail product conteck com INTERNATIONAL CONTEC TECHNOLOGY CO LTD B 8F Hua Tong Building No B19 Che Gong Zhuang West Road Hai Dian District Beijing 100044 China Tel 86 10 8801 8228 Fax 86 10 8801 8209 E mail ict ict com cn SHANGHAI CONTEC MICROELECTRONICS CORPORATION No 481 Gui Ping Road Cao He Jing Hi Tech Park Shanghai 200233 China Tel 86 21 6485 1907 Fax 86 21 6485 0330 E mail contec contec com cn SHENYANG CONTEC MICROELECTRONICS Co LTD No 169 Qingnian Street Shenhe District Shenyang 110015 China Tel 86 24 2392 9771 Fax 86 24 2392 9773 MACROMATE CORP 8F Universal Center No 179 Sec 1 Ta Tung Road Hsi Chih Taipei Hsien Taiwan R O C Tel 886 2 2647 9353 Fax 886 2 2647 9373 E mail intl macromate com tw A 46 368 Ver 200
29. DRAM Memory Sockets Two 168 pin DIMM sockets for SDRAMs in 8MB 16MB 32MB 64MB 128MB and 256MB configurations BIOS Award BIOS PnP support e FLASH EEPROM 256KB for BIOS update e ISA Plug and Play PnP extension e Power management Chapter 1 Introduction e Super I O Winbond 83977TF chipset Parallel Port One high speed parallel port SPP EPP ECP mode Serial Port Two 16550 UART compatible RS 232C 422 485 ports Max baud rate at 115kbps Enhanced IDE Two Bus Mastering EIDE mode up to 4 devices Two EIDE interfaces for up to four devices support PIO Mode 3 4 or Ultra DMA 33 IDE Hard Disk and ATAPI CD ROM FDD Interface Two floppy drives 360KB 720KB 1 2MB 1 44MB 2 88MB LS 120 USB Interface Two USB pin header connectors compliant with USB Specification Rev 1 0 Watchdog Timer 16 level programmable e I O port 0443H to enable watchdog I O port 0441H to disable watchdog e Time out timing select 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 seconds 20 Green Function Power management via BIOS activated through mouse keyboard movement Keyboard Connector PC AT type mini DIN that supports PC AT supports a 5 pin external keyboard connector IrDA Interface Pin header connector for the optional IrDA external connector VGA Display C amp T 69000 VGA chip onboard SVGA for CRT amp Panel 32 bit PCI local bus VGA BIOS with 256KB flash ROM and system BIOS 15 pin connector 1280
30. Halt On Ded 48 BIOS Features reete tv dene ere 49 49 CPU Internal Cache External Cache 49 Quick Power On Self 49 Boot Sequence ect evertere 50 Swap Floppy Drive 50 Boot Up Floppy 50 Boot Up NumLock Status 50 Security ODption aet 50 PCI VGA Palette Snoop esee 50 OS Select for DRAM gt 64 51 Video BIOS Shadow eene 51 C8000 CBFFF Shadow DC000 DFFFF Shadow 51 PC 586U PC User s Manual 41 Chapter 3 BIOS Configuration Chipset Features Setup tait 52 DRAM 52 System BIOS 52 Video BIOS Cacheable 52 8 Bit VO Recovery Time eee 52 16 Bit Recovery 52 Memory Hole at 15 16 53 PCI2J Compliance 21 3 n ied ee e 53 CPU Warning 53 Temperature Fan Speeds V oltages 53 Power Management Setup 4 54 Power 4 54 PM Control by APM eee 54 Video Off
31. K adapter driver 7 The installation program copies the necessary files and creates PROTOCOL INI for use with the adapter 8 Select Close and when prompted restart the computer for changes to take affect and complete the installation NOTE You must have a terminated cable attached to the adapter when you start Windows for Workgroups If you don t Windows for Workgroups hangs PC 586U PC User s Manual 75 Chapter 5 LAN Driver Installation Guide This page was intentionally left blank 76 PC 586U PC User s Manual Chapter 6 SCSI Driver Installation Guide SCSI Driver Installation Guide This chapter serves as an installation guide to the onboard SCSI interface on your CPU card It contains important information to ease the installation and configuration process With the SCSI interface you can connect SCSI peripherals such as hard disk drives scanners CD ROM drives and tape drives Topics covered in this chapter include Installing SCSI Driver for DOS eee 78 Installing SCSI Driver for Windows 95 98 79 Driver Installation for Windows NT eene 81 Installing SCSI driver for OS 2 3 X amp 4 83 PC 586U PC User s Manual 77 Chapter 6 SCSI Driver Installation Guide Installing SCSI Driver for DOS The DOSSETUP EXE program installs the 16bit ASPI drivers SCSI CD ROM driver and the Microsoft CD extensions
32. N Driver Installation Guide Installing LAN Driver for Windows NT This section describes the procedure to install Windows NT v3 5 v3 51 amp v4 0 driver for Realtek RTL8139 PCI Fast Ethernet adapter When you are in Windows NT 1 In the Main group of Windows NT select the Control Panel icon 2 In the Control Panel window choose the Network icon 3 In the Network Settings dialog box choose the Add Adapter button The Add Network Adapter dialog box appears 4 In the list of network cards select lt other gt Requires disk from manufacturer and then press lt Enter gt button 5 Insert the Realtek driver disk in drive A enter drive and pathname A which is the path where the setup file OEMSETUP INF is located and then choose the OK button 6 The screen will appear Select Line Speed dialog box which is provided by RTL8139 SYS driver The default value is auto so that the RTL8139 PCI Fast Ethernet adapter and its driver RTL8139 SYS will auto detect the line speed 10 Mb or 100Mb while the RTL8139 SYS is loading The other values 10 or 100 are only used when you want to force RTL8139 PCI Fast Ethernet adapter to 10 or 100Mb 7 The screen will appear Input EthernetID dialog box which is provided by RTL8139 S YS driver This option is only required when you have more than one Realtek RTL8139 PCI Fast Ethernet adapters on the computer Select SKIP if only one adapter installed on the computer 8 Bus Lo
33. PC 586U PC Single Board Computer for PICMG User s Guide CONTEC Contents Copyright Copyright 1998 CONTEC Co Ltd All Rights Reserved No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC Co Ltd CONTEC Co Ltd makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC Co Ltd Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document nor for results obtained by the user as a result of using this product Limited One Year Warranty CONTEC Single Board Computer are warranted by CONTEC Co Ltd to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office from which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original boards The warranty is not applicable if the device has been tamp
34. S 2 Mouse Connector JP6 Pin ioe ee 3 Ground re Se J16 VGA CRT Connector J16 is a 15 pin VGA CRT connector The pin assignments are as follows Signal Name Pin Pin Signal Name Red ifo Gren te a ee GND 5 6 GND PC 586U PC User s Manual 35 Chapter 2 Installations LCD1 LCD Panel Connector LCDI is a 68 pin dual in line header for flat panel LCD displays The following shows the pin assignments of this connector Signal Pin Pin Signal IRE TE mE om 1 6 1 593 15801 239875 68 67 poo 9 10 Pbi 2 54 LCD1 36 PC 586U PC User s Manual Chapter 2 Installations J17 J18 USB Connectors J17 and J18 are USB connectors that supports up to 127 USB devices The following table shows the pin outs of these connectors he J18 Signal J17 Signal 2 EN Name mm ERTI El H E 5 UsB 6 USB 7 Ground 8 Ground 9 Ground 10 NC J19 Chassis Fan Power Connector J19 is a 3 pin header for the chassis fan pona connector The fan must be a 12V fan TT J20 Pin eum data 2__ 3 Ground eio Hic NIE CEU PC 586U PC User s Manual 37 Chapter 2 Installations LED1 SCSI LED indicates any activity on the SCSI interface LED2 LED3 LAN Activ
35. able or disable the monitoring of IRQ 8 Real Time Clock so it does not awaken the system from Suspend mode 56 PC 586U PC User s Manual Chapter 3 BIOS Configuration PNP PCI Configuration This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value ROM PCI ISA BIOS PNP PCI CONFIGURATION AWARD SOFTWARE INC PNP OS Installed Yes Used MEM base addr Resources Controlled by Manual Reset Configuration Data Disabled Legacy ISA Legacy ISA PnP Legacy ISA PnP PnP PnP PnP Legacy ISA Legacy ISA PnP PnP ESC Quit Y Select PnP F1 Help PU PD Modify IRQ 3 assigned IRQ 4 assigned IRQ 5 assigned IRQ 7 assigned IRQ 9 assigned IRQ 10 assigned IRQ 11 assigned IRQ 12 assigned IRQ 14 assigned IRQ 15 assigned DMA 0 assigned DMA 1 assigned DMA 3 assigned DMA 5 assigned DMA 6 assigned DMA 7 assigned PnP Old Values Shift F2 Color PnP Load BIOS Defaults PCI ISA PnP Load Setup Defaults PNP OS Installed This field allows you to specify if the operating system installed in your system is plug and play aware Note Operating systems such as DOS OS 2 and Windows 3 x do not use PnP Resources C
36. cation display in the next screen Your machine contains more than one hardware bus please select the Bus Type and Bus number on 9 NT will then perform the binding process If any additional network software options were installed you may be prompted for specific information for these packages 10 Restarting your system you will require network service PC 586U PC User s Manual 73 Chapter 5 LAN Driver Installation Guide Installing LAN Driver for DOS Before you start with the installation procedure make sure that the adapter is properly installed and configured Similarly Make sure that your Microsoft Network Client is properly installed If not The installation utility SETUP EXE is located on Microsoft Network Client v3 0 for MS DOS Disk Run SETUP EXE from Disk and the SETUP program screen will appear Follow the instructions The options are specific to your needs The installation procedure will transfer files to a specific directory on the client and modify existing configuration files to fit your specific needs Change to the Microsoft Network Client subdirectory and run SETUP EXE 2 The screen will display some information Press lt Enter gt Respond to the screen prompts selecting Change Network Configuration then press lt Enter gt 4 Move the highlight to Add Adapter press lt Enter gt Select Network adapter not shown on list below Insert the Realtek RTL8139 driver diskette in floppy
37. dating device driver 1 From the Windows 95 desktop select My Computer Control Panel System Device Manager SCSI Controller Initio INI A100U2W Host Adapter 2 Click Driver tab and then click Change Driver tab 3 Type A win95 and insert Initio INI A100U2W driver disk into floppy drive A click OK Windows 95 will copy the new device driver into the hard disk 0 PC 586U PC User s Manual Chapter 6 SCSI Driver Installation Guide Driver Installation for Windows NT Files you need Script files for installation txtsetup oem oemsetup inf disk1 Device driver INIA100 S YS Installation A Install Windows NT on a hard drive from the INI A100U2W SCSI Host adapter 1 If you are installing Windows NT from a floppy drive locate the Windows NT Disk 1 for floppy Installation Make a backup copy of this diskette 2 If you are installing Windows NT from a CD ROM drive locate the Windows NT Setup Disk for CD ROM Installation Make a backup copy of this diskette 3 Put the disk into drive A and turn on your computer 4 Follow the instructions and select CUSTOM SETUP 5 Select OTHER from the list of Additional SCSI Adapters A message will appear on the screen stating that Requires disk provided by a hardware manufacturer Insert the diskette containing INI A100U2W device driver and press ENTER 6 Windows NT will interpret the txtsetup oem and oemsetup inf script files and load INIA100 SYS driver to xxx syste
38. dows 95 directory gt System IOSubSys path For example Click on C WINDOWS SYSTEM IOSUBSYS Click OK 9 Select Yes when prompted to re start Windows 95 NOTE After installation the following driver and related files are stored as listed Windows 95 directory gt System IOSubSys IDEATAPI MPD Windows 95 directory gt System IOSubSys PHXVSD VXD Windows 95 directory gt INF IDEATAPLINF 88 PC 586U PC User s Manual Appendix Appendix A I O Port Address Map B Interrupt Request Lines IRQ PC 586U PC User s Manual 89 Appendix A I O Port Address Map Each peripheral device in the system is assigned a set of I O port addresses which also becomes the identity of the device There are a total of 1K port address space available The following table lists the I O port addresses used on the Industrial CPU Card Keyboard Controller EGA adapter 90 PC 586U PC User s Manual Appendix B Interrupt Request Lines IRQ There are a total of 15 IRQ lines available on the Industrial CPU Card Peripheral devices use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on the Industrial CPU Card Reserved PC 586U PC User s Manual 91 A 46 101 LZJ8881 CONTEC Group 010612 990826 PC 586U PC User s Manual 93 CONTEC Group JAPAN U S A EUROPE KOREA CHINA TAIWAN Headquarters CONTEC Co LT
39. e Selector 13 Setting CPU Frequency amp CPU 15 2 Display Type eiiie aes 18 JPI LED Power Setting ni eet eroe enn 20 JP3 SCSI Terminator Setting 20 JP5 Watchdog Generator Selection 20 JP7 CPU VIO Voltage Setting 21 JPS Disk On Chip Setting eene 21 JP9 RS 232C 422 485 COMO Selection 22 JP10 Clear CMOS 23 J15 External Battery Connector 23 The following examples show the conventions used in this section Switch 1 and switch 2 are set to OFF Switch 3 and switch 4 are set to ON 10 PC 586U PC User s Manual Chapter 2 Installations Jumper Locations on the PC 586U PC 11 v LIL NO SIG 4 ES 194205 135555 Ldf moon 9df XLOEVC8 vat E PC 586U PC User s Manual Chapter 2 Installations S1 Bus Speed Multiplier Setting S1 1 4 Bus Speed 60MHz 1 5x 3 5x 12 PC 586U PC User s Manual S3 1 4 JP7 JP4 CPU Voltage Selector For Single Voltage CPU Intel P54C Cyrix 6x86 AMD K5 C6 mmc on on on on Chapt
40. en designed for and tested with Windows 95 only This driver will only install on systems with Windows 95 1 25 86 The system must contain a supported Intel processor and chipset configuration Ensure that a mouse is connected to the system One of the following versions of Windows 95 must be installed on the system prior to running utility program Windows 95 4 00 950 Retail Windows 95 4 00 950a OSR1 Windows 95 4 00 9506 OSR2 without USB Supplement Windows 95 4 00 950b OSR2 1 with USB Supplement This utility should only be used on desktop systems The utility must not be executed on notebook or portable systems with or without dock It is assumed that the BIOS properly initialized the 82371xB IDE interface for Bus Master IDE operation There are no other non 82371xB IDE controllers add in IDE controller or sound card with IDE enabled on the system PC 586U PC User s Manual Chapter 7 Intel Bus Master IDE Driver Installation Installing the Software This subsection describes how to install the software on a system where Windows 95 is installed NOTE Record the location of the Windows 95 directory before installing the driver 1 Check the System Requirements Windows 95 must be fully installed and running on the system prior to running this software 2 Close any running applications 3 Remove references to installed real mode IDE device drivers in the AUTOEXEC BAT and CONFIG SYS files
41. er 2 Installations EE For Dual Voltage CPU Intel P55C Cyrix 6x86L MX AMD K6 K6 2 on on on on off off on on offon off on Au es on off off on rm off off off on on on on off P55C Pentium MMX PC 586U PC User s Manual WinChip 2 3D OPEN 0 35u OPEN 0 35u ES _ K6 166 200 6x86MX WinChip 2 3D 0 35u P55C 6x86L 13 Chapter 2 Installations For Dual Voltage CPU Intel P55C Cyrix 6x86L MX AMD K6 K6 2 f OPEN N m OPEN 9 on o OPEN E 9 9 i OPEN ON K6 2 0 35u For Dual Voltage CPU Intel 266MHz 0 25micron aT 1 off off oi 14 PC 586U PC User s Manual Chapter 2 Installations 2 en F gt ej m 5 D z E 2 E en gt D un 2 A Q e E E E NH CPU 83 1 4 OPEN OPEN 3 2 3 2 Ea 1 2 3 OPEN Ea 1 2 3 OPEN 8 n off off off off off off off_off off off off off off off n n off off on off off off 34 ff off off off ff off off off off off off on on off oi off off off off on off oi off off off off off on off off off off off off off on off off L 2 ON ON ON b off_off_off_on ON L ff ON off_off_off_on
42. ered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device PC 586U PC User s Manual i Contents How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization Number RMA from our Sales Administration Department before returning any product No product will be accepted by CONTEC group without an RMA number Acknowledgments AMD is a registered trademark of Advanced Micro Devices Inc Award is a registered trademark of Award Software International Inc C amp T is a trademark of Chips and Technologies Inc Cyrix is a trademark of Cyrix Corporation IBM AT and PS 2 is trademarks of International Business Machines Corporation Intel and Pentium are registered trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corporation All other product names or trademarks are properties of their respective owners CAUSION Danger of explosion if battery is incorrectly replaced Rep
43. especially any drivers that control ATAPI CD ROM and special IDE features Use the Notepad utility to do this The driver files are stored in an integrated application setup program This program is a Windows 95 program that allows the driver files to be INSTALLED or DE INSTALLED Execute the driver setup program Run SETUP EXE 4 Click Next on Welcome Screen to read and agree to the license agreement View the text file and choose File Exit to close Notepad and continue NOTE If you click No program will terminate 5 Click Yes if you agree to continue NOTE If you click No the program will terminate 6 Select INSTALL to install the PITX Bus Master IDE Device Driver when prompted to do so NOTE If the driver is currently installed on the system SETUP will ask you whether or not you want to continue Follow the prompts on the screen to Install the driver if desired 7 Click OK to restart the system when prompted to do so 8 Follow the screen instructions and use default settings to complete the setup when Windows 95 is re started Upon re start Windows 95 will display that it has found an Intel PCI Bus Master IDE controller hardware and is installing hardware for it PC 586U PC User s Manual 87 Chapter 7 Intel Bus Master IDE Driver Installation If a New Hardware Found dialog box is displayed requesting the location of the drivers use the mouse to click on the scrollbar and click on the lt Win
44. how to install the VGA drivers that come in the floppy diskette with your PC 586U PC card Please follow the instructions set forth in this chapter carefully Please note that there must be relevant software installed in your system before you could proceed to install the VGA drivers It is recommended that you make a copy of the VGA driver diskette and put the backup copy in a safe place The following items are covered in this chapter Installing the Drivers for Windows 95 66 Driver Installation sese 66 Installing the Drivers for Windows NT 4 0 67 Driver Installation essen 67 PC 586U PC User s Manual 65 Chapter 4 VGA Driver Installation Installing the Drivers for Windows 95 Driver Installation The following section describes the normal display driver installation procedures for Windows 95 Use the following procedures when installing the display drivers for Windows 95 Click Start then Settings then Control Panel Double click on Display Select the Settings page click the Change Display button Click the Change button in the Adapter Type area Click the Have Disk button and press OK Specify the path to the new driver and press lt ENTER gt 1 Insert the drivers disk in the A floppy drive and enter A win95 Example 2 Type in the name of the directory where you copied the drivers either
45. ity LED LED2 and LED3 are light indicators for Link and Data Transfer Activity respectively for the onboard LAN function 38 PC 586U PC User s Manual Chapter 2 Installations Watchdog Timer Configuration The function of the watchdog timer is to reset the system automatically and is defined at I O port 0443H To enable the watchdog timer and allow the system to reset write I O port 0443H To disable the timer write I O port 0441H for the system to stop the watchdog function The timer has a tolerance of 20 for its intervals The following describes how the timer should be programmed Enabling Watchdog AX 000 Choose the values from 0 to MOV DX 0443H OUT Disabling Watchdog AX 000 Any value is fine Dx 0441H OUT DX WATCHDOG TIMER CONTROL TABLE PC 586U PC User s Manual 39 Chapter 3 BIOS Configuration BIOS Configuration This chapter describes the different settings available in the Award BIOS that comes with the PC 586U PC CPU card The topics covered in this chapter are as follows BIOS Introduction 44 BIOS Setup et e 44 Standard CMOS Set p 5 n ht nere 46 ee QM 46 TIE 47 Primary HDDs Secondary 47 Dive Ac Drive Bs e ee eA sh 48 Floppy 3 Mode 48 o DNI e Ness 48
46. king properly is displayed in the Device status box the driver has been correctly installed C Floppyless SETUP If you are running WINNT EXE or WINNT32 EXE to install or upgrade Windows NT when system reboot and screen turn black with the text Setup is inspecting your computer s hardware configuration You have two seconds to press F6 key to enter the DRIVER INSTALL SCREEN this is the time to insert Initio Windows NT installation diskette and type A WINNT to load the INI A100U2W Windows NT driver 82 PC 586U PC User s Manual Chapter 6 SCSI Driver Installation Guide Installing SCSI driver for OS 2 3 X amp 4 X I Installation procedures for INI A100u2W OS 2 3 X amp 4 X device driver A Installed as a secondary controller 1 Open the OS 2 System Folder 2 Open the System Setup Folder 3 Double click Device Driver Install 4 Insert the Initio installation diskette into your floppy drive 5 Change to the OS 2 directory 6 Choose INIA100 ADD then click INSTALL 7 After installation is done OS 2 will report the status B Installed as a primary controller 1 Make backup copies of the OS 2 Diskette 1 2 Copy the INIA100 ADD onto OS 2 Diskette 1 3 Modify the config sys file on Diskette 1 to add BASEDEV INIA100 ADD V 4 Install OS 2 using the backup Diskette 1 II Driver configuration options IN ET Q x B d dd B d A d DM d DM d SM
47. lace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions PC 586U PC User s Manual Contents Chapter 1 Introduction ccccccsssssssssssssssssees Haile d dI D SCrIDUO lyciniy suinn Specifications eese reete poto ara ra Ie Intelligence iaces oaa nae Board Dimensions and Layout Chapter 2 Installations ee CPU Installation eee eee rere eo reo Memory Installation eeeeee Jumpers on the PC 586U PC Connectors on the PC 586U PC Watchdog Timer Configuration Chapter 3 BIOS Configuration Chapter 4 VGA Driver Installation Chapter 5 LAN Driver Installation Guide Chapter 6 SCSI Driver Installation Guide Chapter 7 Intel PIIX Bus Master IDE Driver Installation eee eese eee nee ADDE iiie eren ee ene ere e PI A Port Address B Interrupt Request Lines IRQ PC 586U PC User s Manual Contents iii Contents This page was intentionally left blank iv PC 586U PC User s Manual
48. m32 drivers directory B Adding or Updating the Initio driver to an existing Windows NT 4 0 booted from IDE drive or different type of host adapter 1 Establish a Windows NT session Select CONTROL PANEL from within the MY COMPUTER group Select SCSI ADAPTERS from within the CONTROL PANEL group 2 Select the DRIVERS tab from within the SCSI ADAPTERS group In the DRIVERS window select ADD 3 In the INSTALL DRIVER window select HAVE DISK 4 In the INSTALL FROM DISK window that is displayed enter the Initio Driver path name Insert INI A1000U2W Driver Disk 1 into drive A Type A WINNT select OK PC 586U PC User s Manual 81 Chapter 6 SCSI Driver Installation Guide 5 Select INITIO INI A100U2W Host Adapter select OK to install the INIA100 SYS driver onto your hard disk drive 6 In the WINDOWS NT SETUP window that is displayed enter the Initio Driver path name to continue Type A WINNT select CONTINUE 7 This completes updating the Host Adapter Driver Follow the on screen directions to restart your computer and activate the new driver 8 It is highly recommended that you verify your Windows NT device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL Select SCSI ADAPTERS from within the CONTROL PANEL group Highlight INITIO INI A100U2W SCSI HOST ADAPTER from within the SCSI ADAPTERS listing and select PROPERTIES If This device is wor
49. n Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items Enter to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and Esc to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices 44 PC 586U PC User s Manual Chapter 3 BIOS Configuration ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION LOAD BIOS DEFAULTS SAVE amp EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC Quit V gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Time Date Hard Disk Type The section below the setup items of the Main Menu displays the control keys for this menu Another section at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list NOTE After making and saving system changes with Setup you find that your computer cannot boot the Award BIOS supports an override to the CMOS settings that resets your system to its default We strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully ch
50. nd side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1 to 12 Date 1to31 Year 1994 to 2097 To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time 46 PC 586U PC User s Manual Chapter 3 BIOS Configuration Time The time format is Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt PgDn or keys to set the current time Primary HDDs Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices Each channel can support up to two hard disks the first is the Master and the second is the Slave To enter the specifications for a hard disk drive you must select first a Type There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS Type 1 to 45 are predefined Type User is user definable For the Primary Master Slave as well as Secondary Master Slave you can select Auto under the TYPE and MODE fields This will enable auto detection of your IDE drives and CD ROM drive during POST Press lt PgUp gt lt PgDn gt to select a numbered hard disk type or type the number and press the Enter key The hard disk will not work p
51. ngs are non optimal and disable all high performance features ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER PNP PCI DUT SAVING ESC Quit V gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Load BIOS Defaults except Standard CMOS Setup To load BIOS defaults value to CMOS SRAM enter If not enter N Load Setup Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP POWER a PNP PCI ESC Quit V gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Load BIOS Defaults except Standard CMOS Setup To load SETUP defaults value to CMOS SRAM enter If not enter N PC 586U PC User s Manual 59 Chapter 3 BIOS Configuration Integrated Peripherals This option allows you to determine your hard disk configuration mode and port ROM PCI ISA BIOS INTEGRATED PERIPHERALS AWARD SOFTWARE INC IDE HDD Block Mode Enabled Onboard FDD Controller Enabled IDE Primary Master PIO Auto Serial Port 1 Auto IDE Primary Slave PIO Aut
52. o Serial Port 2 Auto IDE Primary Master UDMA Auto UART Mode Select Standard IDE Primary Slave UDMA Auto Onboard Parallel Port 378H IRQ7 IDE Secondary Master PIO Auto Parallel Port Mode SPP IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto On Chip Primary PCI IDE Enabled On Chip Secondary PCI IDE Enabled USB Keyboard Support Disabled ESC Quit V Select Item F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive IDE Primary Master Slave PIO And Secondary Master Slave PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with controller and CPU directly The system supports five modes numbered from 0 default to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode IDE Primary Master Slave UDMA And Secondary Master Slave UDMA This field allows your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled 60 PC 586U PC User s Manual Chapter 3 BIOS Configuration On Chip
53. om Display list provided then click OK or press ENTER You will then see a warning panel about Third Party Drivers Click on Yes to finish the installation Once the installation is complete the system must be shut down and restarted for the new drivers to take effect When the system has restarted the default graphics mode usually 640x480x256color has been automatically selected Click the Start button then go to Settings and click on Control Panel Click on the Display icon to start the Display Properties window Click on the Settings tab A new screen setting can be selected using either of the following methods A Use the slide bar in the Desktop Area to select new setting B Click on List Modes From the list provided select a new setting then click OK or press ENTER c Click on Test to test the newly selected graphics mode Follow the instructions given on the screen A test screen should appear followed by the Testing Mode window Click on Yes to continue Click on Apply to switch to the new graphics mode Graphics modes are changed dynamically on NT 4 0 so you do not need to shut down and restart for the new screen settings to work PC 586U PC User s Manual 67 Chapter 4 VGA Driver Installation This page was intentionally left blank 68 PC 586U PC User s Manual Chapter 5 LAN Driver Installation Guide LAN Driver Installation Guide This chapter describes LAN features and driver installati
54. on your local hard drive or on a network share Example 3 If you re not sure exactly where the drivers are choose the Browse button to find them 7 Select Device dialog box will appear Select the adapter that corresponds to the one you installed in your machine and click OK 8 Windows 95 will copy the display drivers to the proper directories on your system 9 Continue choosing Close until asked to restart your machine from the Systems Settings Change dialog box 10 After the system has restarted you can go back into the Display applet and select alternate screen resolutions and color depths DUANE 66 PC 586U PC User s Manual Chapter 4 VGA Driver Installation Installing the Drivers for Windows NT 4 0 Driver Installation Once you are in the Windows NT 4 0 environment follow the procedures below to install the VGA drivers in the diskette that comes with your CPU card bo Click the Start button then go to Settings and click on Control Panel Click on the Display icon to start the Display Properties window Click on the Settings tab and then click on Display Type In the Change Display Type window click on Change in Adapter Type This will bring up the Select Device Window In the Change Display window click on Have Disk Follow the directions on the screen to supply the directory where the Windows NT driver files are located Then select OK or press ENTER Select Chips Video Accelerator fr
55. on of the onboard Realtek 8139A Ethernet controller The following items are covered in this chapter Introduction tie RERO 70 Features eee oe eter ete e te etes e a wore darte 70 Software Drivers Support esee 70 Installing LAN Driver for Win98 Windows2000 71 Installing LAN Driver for Windows 95 72 Installing LAN Driver for Windows NT eese 73 Installing LAN Driver for DOS sene 74 Installing Driver for Windows for Workgroups 75 PC 586U PC User s Manual 69 Chapter 5 LAN Driver Installation Guide Introduction Realtek 8139A is a 32 bit 10 100MBps Ethernet controller for PCI local bus compliant PCs It supports the bus mastering architecture and Auto negotiation feature which make it possible to combine one common type of Ethernet cabling an RJ 45 connector for twisted pair cabling that can be used for both 10Mbps and 100Mbps connection Extensive driver support for commonly used network operating systems is also provided Features Conforms to the Ethernet IEEE 802 3u standard Compatible with PCI Local Bus Revision 2 1 specification IEEE 802 3u Auto Negotiation for automatic speed selection Supports Full Duplex Half Duplex Operation Provides 32 bit bus mastering data transfer Supports 10Mbps and 100Mbps operation in a single port Software Drivers Support Novell network drivers
56. ontrolled by This PnP BIOS can configure all of the boot and compatible devices automatically However this capability needs you to use a PnP operating system such as Windows 95 The default value is Manual Reset Configuration Data This field allows you to determine whether to reset the configuration data or not The default value is Disabled IRQ DMA assigned to These fields allow you to determine the IRQ DMA assigned to the ISA bus and is not available to any PCI slot PC 586U PC User s Manual 57 Chapter 3 BIOS Configuration Used MEM base addr This field allows the user to set the base address and block size of a legacy non PnP ISA card that uses any memory segment within the C800H and DFFFH address range If the you have such a card and are not using an ICU ISA Configuration Utility to specify its address range select a base address from the six available options During selection the Used MEM Length field will appear with the block size options If you have more than one legacy ISA card in your system that require the use of this address range you can increase the block size to either 8K 16K 32K or 64K If you are using ICU to accomplish this task leave Used MEM base addr to its default setting of N A 58 PC 586U PC User s Manual Chapter 3 BIOS Configuration Load BIOS Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default setti
57. oppy Drive Connector eee 30 J5 Parallel Port Connector 30 J7 Ultra Wide SCSI Connector eese 31 I8 COMI Serial 32 19 Serial 32 J10 External Keyboard Connector esses 33 J11 CPU Fan Power 33 COMMECOT se sse carte eter e eere uen 33 J13 External ATX Power 33 PS 2 Mouse Connector eeeeeeeseseeeeee 35 JP6 External PS 2 Mouse 35 J16 VGA CRT Connector cesses 35 LCD1 LCD Panel Connector 36 J17 J18 USB Connectors seeeeeeeeeeeeeeneeeennnne 37 J19 Chassis Fan Power Connector eese 37 J20 PS 2 Keyboard 37 LEDI SCSI LED esses 38 LED2 LED3 LAN Activity esee 38 24 PC 586U PC User s Manual Chapter 2 Installations Connector Locations on the PC 586U PC SCSI J7 DISK ON CHIP s v IDE J3 IDE J6 a n mui e N J15 O 82439TX JP7 CPU Socket PC 586U PC User s Manual 25 Chapter 2 Installations Front Bezel Connector
58. osen by both Award and your system manufacturer to provide the absolute maximum performance and reliability PC 586U PC User s Manual 45 Chapter 3 BIOS Configuration Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the Industrial CPU Card is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged ROM PCI ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Mon Aug 19 1996 Time hh mm ss 00 00 00 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Auto 0 Primary Slave None 0 Secondary Master None 0 Secondary Slave None 0 Drive A 1 44M 3 5in Base Memory Drive B None Extended Memory 15360K Floppy 3 Mode Support Disabled Other Memory 384K Video Halt On All Errors Total Memory 16384 ESC Quit Y gt Select Item PU PD Modify F1 Help Shift F2 Change Color At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the F1 key It will display the relevant information to help you The memory display at the lower right ha
59. ress the key If you accept the values the parameters will appear listed beside the drive letter on the screen PC 586U PC User s Manual 63 Chapter 3 BIOS Configuration Save amp Exit Setup This option allows you to determine whether to accept the modifications or not If you type you will quit the setup utility and save all changes into the CMOS memory If you type you will return to Setup utility ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD POWER PNP PCI DUT SAVING ESC Quit V gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Save Data to CMOS amp Exit Setup Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing will quit the Setup utility without saving the modifications Typing N will return you to Setup utility 64 ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD DUT SAVING LOAD SETUP DEFAULTS ESC Quit V gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Abandon all Data amp Exit Setup PC 586U PC User s Manual Chapter 4 VGA Driver Installation VGA Driver Installation This chapter provides information on
60. roperly if you enter incorrect information for this field If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually If you select Type User related information is asked to be entered to the following items CYLS Number of cylinders HEAD Number of read write heads PRECOMP Write precompensation LANDZ Landing zone SECTOR Number of sectors SIZE Automatically adjust according to the configuration MODE for IDE HDD only Auto Normal HD lt 528MB Large for MS DOS only HD gt 528MB and supports Logical Block Addressing NOTE The specifications of your drive must match with the drive table If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually PC 586U PC User s Manual 47 Chapter 3 BIOS Configuration Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are 360KB 1 2MB 720KB 1 44MB 2 88MB 5 25 in 5 25 in 3 5 in 3 5 in 3 5 in Floppy 3 Mode Support This is the Japanese standard floppy drive The standard stores 1 2MB in a 3 5 inch diskette You have four options to choose Disabled No 3 mode floppy drive installed default Drive A Installed 3 mode drive at drive A Drive B Installed 3 mode drive at drive B Both Installed 3 mode drive at drive A and B Video This
61. rs The timing type is dependent on the system design Slower rates may be required in some system designs to support loose layouts or slower memory System BIOS Cacheable Select Enabled allows caching of the system BIOS ROM at F000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Video BIOS Cacheable Select Enabled allows caching of the video BIOS ROM at C0000h F7FFFh resulting in better video performance However if any program writes to this memory area a system error may result 8 Bit Recovery Time This field allows you to select the recovery time allowed for 8 bit I O By default this field is set to 7 Clock 16 Bit Recovery Time This field allows you to select the recovery time allowed for 16 bit I O By default this field is set to 1 Clock 52 PC 586U PC User s Manual Chapter 3 BIOS Configuration Memory Hole at 15M 16M In order to improve performance certain space in memory can be reserved for ISA cards This field allows you to reserve 15MB to 16MB memory address space to ISA expansion cards This makes memory from 15MB and up unavailable to the system Expansion cards can only access memory up to 16MB By default this field is set to Disabled PCI 2 1 Compliance Concurrent PCI allows multiple PCI transfers from the PCI master buses to memory to CPU By default this field is set to Enabled CPU Warning Temperature The
62. t Enabled Parallel Port Disabled ESC Quit V gt Select F1 Help PU PD Modify F5 Old Values Shift F2 Color Load BIOS Defaults F7 Load Setup Defaults This field allows you to select the type of power saving management modes There are fours selections for Power Management Disable No power management Default Min Power Saving Minimum power management Max Power Saving Maximum power management Only available for SL CPU User Define Each of the ranges are from 1 min to 1hr Except for HDD Power Down which ranges from 1 min to 15 min PM Control by APM This field allows you to use the Advanced Power Management device to enhance the Max Power Saving mode and stop the CPU s internal clock If the Max Power Saving is not enabled this will be preset to NO Video Off Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows the BIOS to control the video display card if it supports DPMS Blank Screen This option only writes blanks to the video buffer 54 PC 586U PC User s Manual Chapter 3 BIOS Configuration Video Off After This field specifies the mode after which the Video Off feature is enabled The options are Doze Standby Suspend and N A Doze Mode When enabled and after the set time of system inactivity the CPU clock will run at a slower
63. the drive that the system searches first for an operating system The options are The default value is A C SCSI Swap Floppy Drive This item allows you to determine whether to enable the swap Floppy Drive or not When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek When enabled the BIOS will seek whether or not the floppy drive installed has 40 or 80 tracks 360K type has 40 tracks while 760K 1 2M and 1 44M all have 80 tracks By default this field is set to Enabled Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system By default the system boots up with NumLock On Security Option This field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up PCI VGA Palette Snoop Some display cards that are non standard VGA may not show colors properly This field allows you to set whether MPEG ISA VESA VGA Cards can work with PCI VGA or not When this field is enabled a PCI VGA can work with a MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with a MPEG ISA VESA Card 50 PC 586U PC User
64. ys Use S2 switch to select display type CONTEC S2 1 4 LCD Type Resolution Products ON E E Reserved 1234 1024 x 768 STN XGA Ls e 1024 x 768 18 PC 586U PC User s Manual Chapter 2 Installations J CONTEC S2 1 4 LCD Type Resolution Products ON 1 I a Reserved 1234 off on on on 1280 x 1024 SXGA VGA SVGA CRT only XGA SXGA IPC DT M30 PC T TFT 640x480 IPC DT S35 PC IPC DT S35 PC T TFT rema IPC DS L30S PC T STN 800x600 IPC DS L400 PC T IPC DS L400 PC rema IPC DT L30S PC T IPC DT L400 PC T 800x600 Ipc_DT L400 PC IPC DT L40S PC T PC 586U PC User s Manual 19 Chapter 2 Installations JP1 LCD Power Setting The PC 586U PC XGA interface supports 5V and 3 3V LCD displays Use to change between 5V and 3 3V panel video signal level Setting Pin 1 2 Short Closed JP3 SCSI Terminator Setting Use JP3 a 2 pin header to enable or disable the terminator of the Ultra Wide SCSI on board JP3 Setting JP5 Watchdog Generator Selection Setting Pin 1 2 ii Short Closed Pin 2 3 Reset Short Closed Normal Operation 20 PC 586U PC User s Manual Chapter 2 Installations JP7 CPU Vio Voltage Setting 2 7 Setting Pin 1 2 Short Closed Pin 2 3 Short Closed Pin 1 2 Short Closed D0000 D7FFF Pin 2 3 D8000 DFFFF Short Closed Default PC 586U PC User s Manual 21 Chapter 2

Download Pdf Manuals

Related Search

Related Contents

DFG/TFG 660-690  Owner`s Manual - Drinkstuff.com  body fat analyzer with carrying case body fat monitor heart rate  Security Policy Management for Handheld Devices  日立電磁式水道メーター  User Manual - Better Life  TonneinsL`actrice Rosalie Lajarrige invitée au cinéma Rex  White Rodgers UV100 Instruction Sheet  

Copyright © All rights reserved. Failed to retrieve file