TERC User Manual
Contents
1. With this button switched OUT MONO mode the L R and C Chorus circuits all sum evenly to both the Land R OUTPUTS NOTE If you are simply plugging your guitar in to the TERC and on to only one amp you would use MONO mode button OUT and connect the amp cable to either one of the L or R outputs PRESET MODE feature 5 This is the classic Tri Stereo Chorus slow chorus sound PRESET mode only happens when the PRESET button is IN and the MANUAL button 6 is OUT You will notice that the INTENSITY knobs and the SPEED knob do not function when the PRESET is selected NOTE make sure MANUAL button 6 is OUT or you will hear BOTH the PRESET and the MANUAL sounds at the same time MANUAL MODE 6 MANUAL mode happens when the PRESET button is OUT and MANUAL button is pressed IN In MANUAL mode the L R and C INTENSITY knobs f 7 8 9 and the SPEED knob feature 10 are functional NOTE make sure PRESET button is OUT Combining PRESET amp MANUAL modes Yes by pressing IN both PRESET 5 and MANUAL 6 mode buttons you can combine all the different Low Frequency Oscillators LFO s for all sorts of possibilities It s amazing to hear the PRESET mode s slow swirl with a fast speed selected in the MANUAL mode on top of that INTENSITY knobs 7 8 amp 9 The knobs ONLY function when the MANUAL knob is pressed IN Turning these Clockwise CW will increase the chorus effect level with the deepest chorus being around 12 o clock to 1 o cl2. open then grab it with your fingers and pull out OPERATING VOLTAGE All TERC s have a 3 tap transformer primary that can be quickly wired for any country s power Tap 1 is for Japan and is 100 volt Tap 2 is marked 115 and can be operated off of anywhere between 110 to 120 volts USA amp Canada Tap 3 is marked 230 and can be operated off of anywhere between 220 and 240 volts for Europe You will see this listed on the voltage info area 14 and there are additional voltage decals place at 14 included with your manual should this voltage ever get changed HOW TO CHANGE VOLTAGE Warning This procedure should ONLY be performed by a competent qualified technician Any damage that results from this procedure will void your warranty and may cause injury Unplug the power cable from the wall Unplug the power cable from the power receptacle Open the enclosure by remove all of the small screws around the sides of the TERC and the one tiny screw holding the top section down near the front panel Inside you will see a yellow wire see below diagram simply unsolder that wire move it to the appropriate voltage for you country and resolder EXTERNAL SPEED JACK 15 You can attach an external variable speed control pedal to your TERC This pedal must have a standard 100K B taper potentiometer in it to operate correctly NOTE You must have the TERC s SPEED knob 10 set to FULL CW position or the external spee
3. YST Congratulations on your purchase of the fa bltowe Model TSC 618 If you are a session guitarist you re not quite A List until you have a Tri Stereo Chorus in your rack It is the single most identifiable and certainly the lushest stereo chorus ever made heard on tons of recordings from Joni Mitchell to Don Henley Madonna to Eric Clapton Lukather to Landau Made for a brief time during the 80 s and released under the Dyno My Piano Songbird and Dytronics names it went through many circuit changes Just what is a Tri Stereo Chorus My Electronic Engineer John Greene and are two of only a handful of people who can answer that own 6 of them and have documented and repaired dozens more TSC s are actually three separate chorus circuits each using a Panasonic MN3007 Bucket Brigade BBD chip to create its delayed signal These three choruses are treated with multiple modula tions and mixed together across the stereo output field in a way that not only creates complex images but creates Phasing artifacts as well Add to this a 30 volt internal power supply and you have a super high headroom rack unit that sounds warm huge and doesn t distort when interfaced with high level rack systems and studio patchbays Production of TSC s ceased in the late 80 s and since then the price of these on the used market has skyrocketed to 4000 and more The funny thing is almost all of the ones that I ve checked out were so poorly maint
4. ained that often times one channel or more wasn t even working It s all about the trimmer adjustment on the delay chips if those are adjusted improperly they can sound weak and noisy And now along comes the Fulltone Custom Shop That 80 s Rack Chorus TERC for short to save the day Better constructed than the orginal but 100 the same circuit using better quality parts such as metal film resistors in the power related areas for less noise and gold plated sockets on key opamps that should they ever fail will be as simple as us mailing you a new part and you just popping it in have sourced enough N O S Panasonic MN3007 Delay chips to build a production run of around 3200 units of That 80 s Rack Chorus and to service any in the future if necessary have also produced many custom parts for this project including pots switches transformers and photocells but just the thought of only 3200 of these ever being made with the T E R C logo one them drawing heavily from my love of the vintage Looney Tunes cartoons That s all Folks font just puts a smile on my face Enjoy 2014 FMP Inc All Rights Reserved Michael Fuller President Page 2 FRONT PANEL OUTPUTS 7 INTENSITY SPIEED POV ER i 4 ry T i D CE D EED D S E E STEREO 20 15 10 7 4 2 1 0 1 2 3 6 dB INSTRUMENT LEFT CENTER RIGHT The following features contain references to numbers found on both the Front Panel Page 2 and Back P
5. anel Page 3 FRONT PANEL FEATURES LINE INSTRUMENT button diagram feature 1 Line level devices are items such as amplifier effects loops recording consoles amp patchbays or other Pro Audio devices Push button IN to select LINE LEVEL which reduces the input 12dB and raises the output 12db This switch does not change the volume but you will notice a serious increase in noise hiss unless you are interfaced with proper LINE LEVEL devices If interfacing with line level devices always leave this button pushed IN so as to not distort or damage the TERC s preamp NOTE If plugging the guitar directly in to your TERC jack 21 always have LEVEL switch to OUT position for INSTRUMENT level operation PEAK L E D 2 This LED will light up if the preamp is overloaded by the incoming signal It is unlikely that you will ever see this light up as the TERC has a 30 volt power supply offering 3 3 times more headroom than any 9 volt powered device EFFECT ON OFF BUTTON 3 Push button IN for EFFECT ON push to OUT for EFFECT OFF The TERC is not true bypass and is structured for 1 1 gain neither boosting nor cutting the overall volume OUTPUTS STEREO MONO BUTTON 4 There are 3 analog Chorus Circuits in a TERC Left L Right R and Center C With this button pushed IN to STEREO the L OUTPUT 17 amp 18 emits signal from the L amp C Chorus circuits only and the R OUTPUT 19 amp 20 emits signal from the R amp C circuits only
6. d controller will not operate EXTERNAL CANCEL 16 This jack allows you to externally cancel the Chorus effect but you will still be running through the TERC s preamp circuitry It is a typical Tip to ground cancels jack 1 4 OUTPUTS 17 and 19 These outputs are configured unbalanced for standard shielded mono guitar cable plugs Do not use TRS balanced cables here XLR OUTPUTS 18 and 20 XLR outputs are balanced with Pin2 Hot and Pin1 going to chassis ground to avoid the grounding issues found in many other devices 1 4 XLR COMBO INPUT 21 This jack accepts 1 4 mono guitar cable unbalanced 1 4 Balanced TRS and XLR Balanced plugs WARRANTY Fulltone products carry a Limited 5 year Warranty to the original owner with proof of purchase the product was bought new from an authorized Fulltone dealer There is no need to register your product simply keep a copy of your original sales receipt The Warranty covers failure due to manufacturing errors only and is void if a mod or repair is attempted by anyone other than Fulltone or an authorized Fulltone Repairman and or if we deem that any operator caused abuse or damage has occurred Things that would cause voiding of the Warranty would include the use of an incorrect power supply water damage physical abuse etc If you are having a technical issue please do not call Instead email engineer fulltone com to troubleshoot the problem and only after troublesh
7. ock Chorus is created by taking the original signal processing that signal through a delay and modulating pitchbending it then mixing the original and the processed signals back together The strongest chorus sounds you can get are when the orginal and processed signals are mixed together equally with a 50 50 balance the chorus is created by these original and processed signals fighting against each other Once you change the balance so that the processed signal gets louder than the original signal you are only hearing the processed signal which is what we call VIBRATO Therefore when any of the TERC s INTENSITY knobs are past 1 o clock your will be hearing mostly the pitchbend vibrato from those channels something Michael Landau made famous during his Raging Honkies Band period SPEED knob 10 This knob only operates when the MANUAL mode button is pressed IN Turn it CW to increase the rate of the modulation turn it counter clockwise CCW to decrease the modulation rate It has a ridiculously wide range of available speeds and you can turn it CCW to a point where it is so slow the entire modulation cycle takes five seconds or more to complete You will hear both Flange and Phase effects at lower speeds especially with the INTENSITY knobs around 12 o clock OUTPUT LED s 11 These L amp R LED ladders monitor the OUTPUT signal from your TERC It is not uncommon to see these jump up to the 3 dB area please make sure yo
8. ooting for the scheduling of your repair After we have decided that a repair is necessary we will email you an Acrobat PDF copy of our Return Authorization Form RA Form You then print it out fill out all the information and include it in the box with the effect you are sending Fulltone Musical Products Inc is not responsible for and injuries and or damages related to the use of our products The Customer is always responsible for any shipping costs VAT duties or Taxes that may result from the international shipping during sale or repair Thank you for buying the Fulltone Custom Shop That 80 s Rack Chorus Fulltone Musical Products Inc 11018 Washington Blvd Culver City CA 90232 USA Sales sales fulltone com Repairs engineer fulltone com website www fulltone com 2014 FMP Inc All Rights Reserved
9. ur signals are adjusted so that it only briefly visits the red otherwise distortion will occur POWER switch 12 Press this IN to turn on the power to your TERC If it does not light up RED check if the power cable is plugged snuggly in to the power cable receptacle 13 or check the fuse which is located in the power cable receptacle 13 on the back of the TERC 2015 FMP Inc All Rights Reserved Page 3 BACK PANEL E 4 5 D 1D 19 20 a That 80 s Rack Chorus EXT SPEED EXT CANCEL JS puTPuT Arstop Model TSC 618 r r k b CABLE PRIOR TO OA PN H NS i N 4 Ris I EE i a E i Ke OPENING DEVICE SERIAL 0000 Illtoue A h yy AN j f A J 110 120V 60Hz TL stone mee PRODUCTS INC 0 3 AMP 250V 11018 Washingto dcn ae ity CA 90232 NS AA TA Use a 100K TIS MONO T S MONO SLO BLO FUSE HAND BUILT IN Ee U S A B Taper Pot PIN 2 HOT PIN 2 HOT PIN 2 HOT The following features contain references to numbers found on both the Front Panel Page 2 and Back Panel Page 3 BACK PANEL FEATURES POWER RECEPTACLE FUSE 13 Accepts a standard computer type IEC detachable Power Cable The cable is included for US amp Canada only To access the 0 3amp 5mm x 20mm fuse simply unplug the IEC power cord from the TERC s receptacle and use a small flat blade screwdriver to press down on the tab located inside the cutout area under the middle pin Press down on this tab and the fuse door will pop
Download Pdf Manuals
Related Search