Home

User manual CitySkape 48&48DMX Single Colour

image

Contents

1. Use the UP DOWN buttons to select desired effect channel List of control channels Stro a shutter strobe function dimr a dimmer F dim a fine dimmer 4 Press the ENTER button and use the UP DOWN buttons to set value press the ENTER button to confirm it 16 CitySkape 48 Single colour 6 5 Test sequences Use this menu to run demo test sequences without an external controller which will show you some possibilities of using the CitySkape 48 6 6 Stand alone setting EL ALI The fixtures on a data link are not connected to the controller but can execute pre set programs which can be different for every fixture Stand alone operation can be applied to the single fixture or to multiple fixtures operating synchronously Synchronous operation of multiple fixtures requires that they must be connected on a data link and one of them is set as a master MASt and the rest as the slaves SLA Up to 32 fixtures can be connected in a master slave chain Only one fixture can be set as the master Note Disconnect the fixtures from the DMX controller before master slave operating otherwise data collisions can occur and the fixtures will not work properly See the chapters Stand alone operation and Master slave connection Auto Automatic playback This function allows you to select the program which will be played after switching the fixture on Selected program will be played continu
2. Use this menu to read useful information about the fixture status To display desired information 1 Use the UP DOWN buttons to find the InFo menu 2 Press the ENTER button 3 Use the UP DOWN buttons to select the required menu item 4 Press the ENTER button to confirm the choice Po ti Power On Time Use the menu item to read the number of operation hours for each LEDs operating mode FuLL Max light output from the fixture totL the function shows the total number of the operation hours in the FuLL mode since the CitySkape 48 has been fabricated rESEt the function shows the number of the operation hours that the CitySkape 48 has been powered on in the FuLL mode since the counter was last reset In order to reset this counter to O you have to press and hold the UP and DOWN buttons and at the same time press the ENTER button EcO Economical mode totL the function shows the total number of the operation hours in the EcO mode since the CitySkape 48 has been fabricated rESEt the function shows the number of the operation hours that the CitySkape 48 has been powered on in the EcO mode since the counter was last reset In order to reset this counter to O you have to press and hold the UP and DOWN buttons and at the same time press the ENTER button DM In DMX values Select this function to read DMX values of each channel received by the fixture tEMP Fixture Temperatures Select this menu to
3. in the menu item r InF SPEC gt rAdl gt r InF 4 Tounlink the fixture from DMX transmitter The fixture can be unlinked from receiver via the menu item r UnL SPEC gt rAdl gt r UnL 10 Technical specifications Power supply e Electronic auto ranging e Input voltage 100 240V AC 50 60 Hz e Fuse T1 25AH e Power consumption All LEDs at full Full mode 60W 1140 VA Eco mode 40 W 90VA Optic 8 Effects e Light source 48 Luxeon Rebel LEDs e Optical system 12 beam angle 25 egg crate module included barndoors included 45 and 45 x15 egg crate modules optionally available e Adjustable strobe sequences eLumen maintenance Channels Power La full intensity mode All LED Full mode 68 000 channels Eco mode 76 000 Lo 70 maintenance of initial lumen output in hours Control e 4 digit LED display and four control buttons e USITT DMX 512 RDM support e DMX protocol modes 2 1 3 control channels e Operations modes DMX Stand alone Master Slave e Manual control of all effects via control panel e 3 user editable programs each up to 68 steps Wireless DMX RDM module only for WDMX version e Compliance with USITT DMX 512 1986 amp 1990 and 512 A e Full DMX fidelity and frame integrity e Auto sensing of DMX frame rate and frame size e lt 5ms DMX latency 21 CitySkape 48 Single colour e Operational frequency range of 2402 2480 MHz e Producer LumenRadio Strobe e Strobe
4. overhead use always install a safety rope 4 that can hold at least 10 times the weight of the fixture You must only use safety rope with screw on carbine Pull the safety rope through the adapter for Omega holder 1 and over the trussing system Quarter turn quick locks ge es E 913 Ensure that the structure truss to which you are attaching CitySkape 48 Single colour the fixture is secure Caution Fixtures may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do not install the device and consult installation with an expert 3 2 Connection to the mains Fixtures must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulation Install a suitable plug on the power cord note that the cores in the power cord are colored according to the following table Core Eu Core US Connection Plug Terminal Marking Brown Black Live L Light blue White Neutral N Yellow Green Green Earth D This device falls under class one and must be grounded 3 3 Changing the lens array The standard beam angle of the fixture without lens array is 12 If you need a wider beam angle than 12 you have to install the eggcrate lens module 25 or the optional eggcrate lens module 45 45 x15 or eggcrate top hat module for placing plastic f
5. read the temperatures of the fixture Cur t the current temperature of the fixture inside Hi tE the menu item shows the max temperatures of the fixture inside since the CitySkape 48has been fabricated rSEt the menu item shows the maximum temperatures of the fixture inside since the counter was last reset In order to reset this counter to O you have to press and hold the UP and DOWN buttons and at the same time press the ENTER button Note The ambient temperature should not exceed 40 C The temperatures can be displayed in either C or F units see option tEM U in the menu Pers VErS Software Versions Select this function to read the software version of the fixture processor 15 CitySkape 48 Single colour 6 3 Personality oc C Por A Use this menu to modify the CitySkape 48operating behaviour DM Pr DMX preset Select this menu item to set a desired DMX mode Please refer to the chapter DMX protocol for detail description of each DMX mode dMH I DMX input Select this menu item to select desired DMX input dMH Wire DMX rAd l Wireless DMX rAd o Wireless DMX gt wire DMX The fixture receives wireless DMX signal and sends it to its DMX output connector Next fixtures can be connected to the fixture by DMX cable DiSP Display adjusting This function allows you to change the display settings d On this function allows you to keep the display on or to turn off aut
6. D THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR CitySkape 48 Save it for future reference This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty 1 Safety instructions DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT Make sure that the available voltage is not higher than stated on the rear panel of the fixture This fixture should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied consult your authorized distributor or local power company Always disconnect the fixture from AC power before cleaning removing or installing the fuses or any part Do not overload wall outlets and extension cords as this can result in fire or electric shock Make sure that the power cord is never crimped or damaged by sharp edges Check the fixture and the power cord from time to time Do not install the unit near naked flames During the operation the housing becomes
7. ROBE CitySkape 48 Single Colour CitySkape 48 Single Colour Wireless DMX CRMX USER MANUAL ROBE Lighting s r o e Czech republic www robe cz CitySkape 48 Single colour Table of contents 1 Safety a Mn ac atte i tai i da dite a De Da a dE 8 a atat LPO da a den 3 2 Fixture exterior VIEW accede ec etica adi a hae a ent in ee ne TS 5 KEEN EE 5 3 Rigging the TIA ta EE ll SEN Data a 0 EEN a tai d n 5 3 2 Connectionto the MAINS vii A AAA Ai 6 ERA A A D el Dee 6 3 4 Installation ofthe batt g porte ugestouss data 8 3 5 BDMX512 ele Le LE 9 3 6 Master slave CONNectioN ccccccccscssscsccccccescccesscocccececscesccsasscesseecesscuseascesceseeseccssassessseccenasecssesecesecsscssessseceuseoeeass 9 3 7 Stand alone GPerationn EERTE EEE E R E T nasa E ets ei teens EE 10 4 CitySkape 48 Single colour DMX protocOl iii 11 Eege ell e EE 12 6 Eixt re MENU A iia E 14 G L Eixt re Ada ES Sie tt a tan ala a AA tit ca le tada 14 6 2 Fixtureinformation ii a oa at d ta d ves n i al Rat ada ni ln tt te ata ana da aia 15 6 3 Personalice a Sa dal da ee 16 6 4 Manual mode RN 16 6 S Test SCQUENCOS ys oii rt TEE 17 6 6 Stand alone settings EE EE 17 6 7 Special functions cari NO 18 K RI 19 8 Error and information MESAS iii ne alea tai 00 ia a a ll dos 20 9 Wireless DMX A ais 21 10 Technical Specific ii Ee EE EES dE er 21 IT Cleaning NA MAINE EE 23 CitySkape 48 Single colour FOR YOUR OWN SAFETY PLEASE REA
8. any object when the fixture is under operation The fixture becomes very hot during operation Allow the fixture to cool approximately 30 minutes prior to manipulate with it Operate the fixture only after having familiarized with its functions Do not permit operation by persons not qualified for operating the fixture Most damages are the result of unprofessional operation Do not attempt to dismantle or modify the unit Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons Please use the original packaging if the fixture is to be transported If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc CitySkape 48 Single colour 2 Fixture exterior view 1 Lens array 2 Radiator 4 Base 6 Power cord 7 Antenna 6 Power cord 7 DMX in 8 DMX out 3 Installation 3 1 Rigging the fixture 3 Control board Wireless DMX version The CitySkape 48 can be rigged in any orientation on a truss without altering its operation characteristics Installation on the truss allows the adapter for Omega holder 1 fastened to the fixture base with two bolts 2 and the omega holder 3 for fastening a clamp Pull through the safety rope 4 under the mounting holder and For
9. ay have better light parameters than previous products 11 Cleaning and maintenance DANGER Disconnect from the mains before starting any cleaning or maintenance work Rinse off loose dirt with low pressure water spray Wash the housing with a soft brush or sponge and a mild non abrasive washing detergent Rinse it There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by a qualified person Should you need any spare parts please use genuine parts Specifications are subject to change without notice October 24 2011 23
10. e box Avoid interrupting the process Update status is being displayed in the Info Box window When the update is finished the line with the text The fixture is successfully updated will appear in this window and the fixture will reset with the new software Note In the case of an interruption of the upload process e g power cut the fixture keeps the updating mode and you have to repeat the software update again For example The fixture was switched off before finishing software upload After switching again the fixture on the fixture is still in the updating mode and the display is dark Restart the Software Uploader program and repeat software update from your PC 7 RDM This fixture is ready for RDM operation RDM Remote Device Management is a bi directional communications protocol for use in DMX512 control systems it is the new open standard for DMX512 device configuration and status monitoring The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non RDM equipment By using a special Start Code and by complying with the timing specifications for 19 CitySkape 48 Single colour DMX512 the RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific moving lights RDM allows explicit commands to be sent to a device and responses to be received from it The list of command s for CitySkape 48is the follow
11. e other slave fixtures All fixtures have a definite synchronized starting point when playing back their programs The number of running program is the same in all slaves and depends on the master s choice menu St AL Every fixture runs its program repeatedly starting the program step No 1 when requested by the master Example If the slave fixture has a shorter program length it will continuously repeat its program until the master fixture finishes its own program and restarts its program running slave 1 prog step 3 will not be finished If the slave fixture has a longer program length it will restart at prog step 1 before it completes all its prog steps slave 2 prog step 5 will not be played see the picture bellow Prog step 1 Master Prog step 1 Prog step 2 Prog step 3 Prog step 4 Prog step 5 Program length Prog step 1 Continous repeating Slave 1 Prog step 1 Prog step 2 Prog step 3 Prog step 1 Prog step 2 Prp Sato Program length Slave 2 Prog step 1 Prog step 2 Prog step 3 Prog step 4 Program length Time 2 Note Disconnect the fixtures from the DMX controller before master slave operating otherwise data collisions can occur and the fixtures will not work properly 10 CitySkape 48 Single colour 4 CitySkape 48 Single colour DMX protocol Version 1 0 Mode Channel Type of control Strobe Shutter closed s
12. effect with variable speed max 20 flashes per second e Pre programmed random strobe pulse effects Dimmer e Smooth 16 bit dimming from O 100 Connection e DMX data in 1 3m long cabel with 5 pin XLR male e DMX data out 1 3m long cabel with 5 pin XLR female ePower 1 4m long power cabel without plug Wire DMX only Rigging e Via omega holder Temperatures e Maximum ambient temperature 40 C e Maximum housing temperature 80 C Dimensions mm E e Ly E 5 Le fi Y g D E Y ZS m 2 E 3 lo _ o 5 Laz Er WDMX version Weight e 3 kg 22 CitySkape 48 Single colour Protection factor e IP 65 except DMX IN OUT XLR connectors Included items e 1 x CitySkape 48 CitySkape 48 W e 1 x Eggcrate lens module 25 No 10980061 e 1 x Barn doors module No 10980062 e 1 x Adapter for Omega holder No 99012673 e 1 x Omega holder No 99010420 e 1 x User manual Optional accessories e Eggcrate lens module 45 No 10980065 e Eggcrate lens module 45 x 15 No 10980066 e Eggcrate top hat module without lenses No 10980089 e Quad top loader case without castors No 10120080 e Octuple top loader case without castors No 10120081 e Flash cable RS232 DMX No 13050624 Note By reason of the fast moving development of LED technology newer products m
13. hot up to 80 C Refer servicing to qualified service personnel This fixture falls under protection class Therefore this fixture has to be connected to a mains socket outlet with a protective earthing connection Do not connect this fixture to a dimmer pack LED light emission Risk of eye injury Do not look straight at the fixture s LEDs during operation The intense light beam may damage your eyes Keep compustible materials at least 20 cm away from the fixture If the fixture has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Avoid brute force when installing or operating the fixture 3 CitySkape 48 Single colour The fixture was designed for both indoor and outdoor use This fixture must not be used for underwater installation When choosing the installation spot please make sure that the fixture is not exposed to extreme heat or dust Avoid using the unit in locations subject to possible impacts The fixture body never must be covered with cloth or other materials Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Do not block the front objective LEDs with
14. ing Parameter ID DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO SUPPORTED_PARAMETERS SOFTWARE_VERSION_LABEL DMX_START_ADDRESS IDENTIFY_DEVICE DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL DEVICE_LABEL SENSOR_DEFINITION SENSOR_VALUE DISPLAY_LEVEL DEVICE_RESET DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION STATUS_MESSAGES STATUS_ID_DESCRIPTION DEVICE_HOURS Please see the Robe Universal Interface user manual for detail description of RDM operation 8 Error and information messages t M Er Temperature measuring error The message informs you that the LED module temperature sensor is defective MA Er Master error The fixture is set as a master and DMX console is connected to the fixture 20 CitySkape 48 Single colour 9 Wireless DMX operation The wireless version of the CitySkape 48 is equipped with the Lumen Radio CRMX module and antenna for receiving DMX signal CRMX module operates on the 2 4 GHz band 1 Select wireless DMX input from the menu PErS PErS gt dMH I gt rAd l 2 Set desired time after that the fixture will be automatically unlinked from the transmitter in case that no signal is transmitted from transmitter faulty transmitter in the menu PErS PErS gt rAd t 3 To link the fixture with DMX transmitter The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter After linking the level of DMX signal 0 100 is displayed
15. m edge into the second groove on the bottom side of the radiator and tighten four locking screws M2 to secure this barn doors module on the radiator barn doors Lens module Radiator Insert barn doors module into the second groove Radiator Radiator Lock the barn doors module with the screws Never close the barn doors during fixture operation CitySkape 48 Single colour 3 5 DMX 512 connection The fixture is equipped with two 5 pin XLR connectors for DMX input output Only use a shielded twisted pair cable designed for RS 485 and 5 pin XLR connectors in order to connect the controller with the fixture or one fixture with another Wiring of the XLR connectors DMX output DMX input XLR socket rear view XLR plug rear view Sd 50 O1 49 o Sa 3 1 Shield 2 Signal 3 Signal 4 Not connected 5 Not connected To build a DMX chain 1 Connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain 2 Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture 3 Always connect the DMX output with the input of the next fixture until all fixtures are connected Do not overload the link Max 32 fixtures may be connected on a DMX link DMX console gt Terminator Cau
16. of LEDs during fixture burn in at a factory Users should not change the setting rAdl Wireless DMX The menu serves for reading of the wireless operation status only for Wireless DMX version r InF Wireless DMX information The menu item shows level of received signal in If the fixture is not linked to the transmitter no L is displayed r UnL Wireless DMX unlink The item serves for unlinking the fixture from transmitter uPd M Updating mode The menu item allows you to update software in the fixture via either serial or USB port of PC The following are required in order to update software PC running Windows 95 98 2000 XP or Linux DMX Software Uploader Flash cable RS232 DMX No 13050624 if you want to use a serial port of PC Robe Universal Interface if you want to use an USB port of PC Notel Software update should execute a qualified person If you lack qualification do not attempt the update yourself and ask for help your ROBE distributor Note 2 DMX address programs 1 3 and all items in the menu PErS will be set to their default values To update software in the fixture Installation of the DMX Software Uploader 1 DMX Software Uploader program is available from the ROBE web site at WWW robe cz 2 Make a new directory e g Robe Uploader on your hard disk and download the software into it 3 Unpack the program from the archive II Fixture software updating 1 Determine which
17. of your port is available on your PC and connect it with the DMX input of the fixture if you using the flash cable RS232 DMX 18 CitySkape 48 Single colour with the DMX input of the Robe Universal Interface if you using the USB cable Disconnect the fixture from the other fixtures in a DMX chain Turn both the computer and the fixture on 2 Switch the fixture to the updating mode 1 Use the UP DOWN buttons to find SPEC menu Press the ENTER button Use the UP DOWN buttons to select uPd item Press the ENTER button Use the UP DOWN buttons to select yES option Press the ENTER button Note If you do not want to continue in software update you have to switch off and on the fixture to escape from this menu 3 We recommend to cancel all running programs before start of the Software Uploader 4 Run the Software Uploader program Select desired COM and then click on the Connect button NU PUN ColorSpot 700EAT Software Uploader v3 0 Select COM if the seri l port is used DN Select DreamBox1 gt if the USB port is Se Some used If the connection is OK click on the Start Uploading button to start uploading It will take several minutes to perform software update If the option Incremental Update is not checked all processors will be updated including processors with the same software version If you wish to update only later versions of processors check the Incremental Updat
18. oil under it How to install eggcrate lens module 1 Disconnect the fixture from the mains 2 Put the top edge of the eggcrate lens module into the second groove on the top side of the radiator detail E and the bottom edge into the second groove on the bottom side of the radiator detail F and tighten two locking screws M2 to secure the eggcrate lens module on the fixture s radiator Lens module Radiator Lens module Insert the lens module into the second groove Radiator Radiator Lens module Lock the lens module with the screws CitySkape 48 Single colour To install eggcrate lens module with frost foil 1 Disconnect the fixture from the mains 2 Place the frost foil of dimensions of 61mm x 217 mm under eggcrate top hat lens module on the fixture s radiator 3 Fasten the eggcrate top hat lens module on the radiator the same way as the eggcrate lens module Eggcrate top hat module Radiator The frost foil has to stand temperature of 80 C CitySkape 48 Single colour 3 4 Installation of the barn doors You can install the barn doors to better define illuminated surface The barn doors module is fastened in the same way as the lens array module 1 Disconnect the fixture from the mains 2 Putthe top edge of the barn doors module into the second groove on the top side of the radiator detail A and the botto
19. omatically 2 minutes after last pressing any button on the control panel d Int select this function to adjust the display intensity 30 min 100 max turn select this function to turn the display by 180 tEM U Temperature Unit Use this menu in order to display the fixture temperatures in desired units C or F LoAd Load of LEDs The menu allows to choose 2 different operating modes for fixture FuLL Maximum light output EcO The light output is decreased by 25 In Po Init effect positions Use this function to set all effects to the desired positions to which they will move after switching the fixture on if DMX is not being received rAd t Unlink time Use this menu to set time after that the linked fixture will be unliked from the transmitter if the transmitter does not transmit DMX signal OFF Fixture is permanently linked 1 255 Time from 1 255 minutes dF SE Default Settings The menu item sets all fixture parameters to the default factory values 6 4 Manual mode NO_ An beeen Use this menu for control the fixture without connected DMX console PrE C Preset effects control Select this menu to call up preset positions of the channel effects Man C Manual effect control Select this menu to control all channels via buttons of the control board To control fixture channels 1 Use the UP DOWN buttons to find Man C menu 2 Press the ENTER button 3
20. ously in a loop 1 Use the UP DOWN buttons to find St AL menu Press the ENTER button Use the UP DOWN buttons to select Auto item Press the ENTER button Use the UP DOWN buttons to select desired program Press the ENTER button to confirm the choice DUR SN PLAY Playing program By enter to this menu a complete overview of all programs is offered from which the program to be run can be selected 1 Use the UP DOWN buttons to find St AL menu 2 Press the ENTER button 3 Use the UP DOWN buttons to select desired program 4 Press the ENTER button The selected program runs in a loop Edit Editing a program The fixture offers 3 freely editable programs EPG 1 EPG 3 each up to 68 steps Every program step includes a fade time the time taken by the steps channel status to reach the desired level and a step time the total time occupied by the step in the program E g If F tim 5 second and S tim 20 second effects will go to the desired position during 5 seconds and after that they will stay in this position for 15 seconds before going to the next prog step 1 1 Use the UP DOWN buttons to find St AL menu and press the ENTER button Use the UP DOWN buttons to select Edit menu and press the ENTER button Use the UP DOWN buttons to select a program you want to edit PrG 1 PrG 3 and press ENTER button Use the UP DOWN buttons to select a desired program step St 01 St 68 and
21. press ENTER button Use the UP DOWN buttons to select a channel you want to edit and press the ENTER button List of editable items P End a total number of the program steps value 1 68 This value should be set before start Programming e g if you want to create program with 10 steps set P End 10 Stro a shutter strobe function 0 255 Ot No 17 CitySkape 48 Single colour dimr a dimmer 0 255 F dim a fine dimmer F tim a fade time 0 25 5 seconds S tim step time value 0 25 5 seconds COPY this item duplicates the current prog step to the next prog step The item P End is increased automatically 6 Use the UP DOWN buttons to set a DMX value of the channel and then press the ENTER button 7 Use the UP DOWN buttons to select next channel and press the ENTER button 8 After having set all channels in the current program step press the MODE button to go by one menu level back and select another program step 6 7 Special functions COcr l LL rdML Code This menu item shows the first part of the RDM identification code rd MH Code This menu item shows the second part of the RDM identification code Ad Effect Adjustment The menu allows calibration of each LEDs array dMH DMX Values The menu item enables to control all LEDs before calibrating each LEDs array CAL U Calibrating unit The menu serves for fine current calibration
22. tep 32 63 Shutter open step 64 95 Strobe effect from slow to fast proportional 96 127 Shutter open step 128 143 Opening pulses in sequences slow gt fast proportional 144 159 Closing pulses in sequences fast gt slow proportional 160 191 Shutter open step 192 223 Random strobe effects from slow to fast proportional 224 255 Shutter open step 2 Dimmer 0 255 Dimmer intensity from 0 to 100 proportional Dimmer fine 3 0 255 Fine dimmer intensity from low to high proportional 11 CitySkape 48 Single colour 5 Control menu map Default settings Bold A CC few SSES RI SLA Mod 2 rAd rAd o 5 6000 turn C F FuLL EcO 12 CitySkape 48 Single colour Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 1 255 minutes St 01 St 03 di 01 di 06 0 255 0 255 0 25 5 sec CitySkape 48 Single colour EC PE PE AE EE O EI ZE IRC AR E RR RR HS SS Sg SS ES a A AAA IN E CS IE EE ECC ET he Thea HS EEE E E Only for Wireless DMX version 6 Fixture menu The control panel menu allows to set the fixture according to your needs obtain information on its operation test its various parts and lastly program it if it has to be used in a Stand alone mode The four control buttons on the front have the following functions vd ESCAPE button leaves menu without saving changes lt l ENTER button enters menu confirms adjusted val
23. tion Terminate the link by installing a termination plug in the output of the last fixture The termination plug is a male 3 pin XLR plug with a 120 Ohm resistor soldered between Signal and Signal 3 6 Master slave connection To build a master slave chain Connect the DMX output of the master fixture in the data chain with the DMX input of the first slave Always connect output with the input of the next slave until all slaves are connected up to 32 fixtures gt Terminator eme Terminator Caution It is necessary to terminate the input of the master fixture and the output of the last slave with a 120 Ohm resistor in order to ensure the proper transmission on the data link CitySkape 48 Single colour 3 7 Stand alone operation The fixtures on a data link are not connected to the controller but can execute pre set programs which can be different for every fixture To set the program to be played see the Stand alone setting menu St AL Stand alone operation can be applied to the single fixture or to multiple fixtures operating synchronously Synchronous operation of multiple fixtures requires that they must be connected on a data link and one of them is set as a master master mode and the rest as the slaves slave mode To set the fixture as the master or slave see the Fixture Address menu A001 Only one fixture can be set as the master The master fixture starts simultaneous program start in th
24. ues and leaves menu A UP and Y DOWN buttons move between menu items on the same level sets values After switching the fixture on the fixture display shows the current DMX address Use the UP DOWN buttons to scroll through the various menu items To select desired item press the ENTER 6 1 Fixture Address Use this menu to set the DMX address of the fixture or set the fixture as a Master Slave dM Ad DMX addressing Select this submenu to set a DMX start address To set a DMX address 1 Use the UP DOWN buttons to find A001 menu Press the ENTER button Use the UP DOWN buttons to select desired start address Press the ENTER button to confirm the choice PIWS MA SL Master slave addressing Select this submenu to set the fixture as a master or slave Option d AbL deactivates master slave setting 14 CitySkape 48 Single colour To set a fixture as a master or slave 1 Use the UP DOWN buttons to find A001 menu Press the ENTER button Use the UP DOWN buttons to select MA SL item Press the ENTER button Use the UP DOWN buttons to select either master MASt or slave SLA Press the ENTER button to confirm the choice O Mir Za Oo Zei Note After switching on the CitySkape 48will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will start to flash with actually set address 6 2 Fixture information USE INFO

Download Pdf Manuals

image

Related Search

Related Contents

ステンレスボトル MBP  Distributed Polling System User Manual  EW-BW50 EW-BW30 取扱説明書  del Diario Oficial. Documento sin oficialidad  Samsung Samsung Galaxy Tab 8.9 LTE    Xerox 180 User's Manual  Samsung SDC-CA907BW User Manual  SuperScript 100C Online User`s Guide  Instruction Manual  

Copyright © All rights reserved.
Failed to retrieve file