User Manual
Contents
1. AQUAPORT GOOD WATER MADE EASY DELUXE COLLECTION Full Flow VVater Filtration system AQP FKW AQBUAPORT GOOD WATER MADE EASY Congratulations on your purchase of an Aquaport Water Filtration System The Full Flow Water Filtration System connects directly to an existing faucet It filters all cold water from the tap and eliminates the need for a specialised filter tap Note Please read through the instructions carefully before using or installing the product and ensure that the manual is kept in a safe place for future reference The system must be properly installed and located in accordance with the installation instructions before it is used During the set up of this product if you have any questions comments issues DO NOT RETURN TO STORE For service and technical advice on this product free call 1300 764 325 Register your warranty online at www aquaport com au warranty CUSTOMER HOTLINE 1300 764 325 Aquaport Corporation Pty Ltd PO Box 81 Findon SA 5023 Australia Telephone 1300 764 325 AS NZS 3497 Facsimile 08 8354 0722 License Number Email aquaport aquaport com au WMKA22062 Web www aquaport com au WaterMark IAPMO R amp T Oceana WATER QUALITV Caution Do not use with water that is microbiologicallv unsafe or with water of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water that may co2. or Full Flow 10 000 litres Water Filter whichever occurs first Filter cartridge life varies depending on water quality Your cartridge may need replacing earlier than 12 months if you notice a reduction in volume or flow from the filter faucet or return of an unpleasant taste odour to the filtered water 1 Isolate water supply Turn cold tap on to release any excess water still present in system 2 Remove new filter cartridge from packaging 3 Remove expired filter cartridge from system by turning the filter cartridge 1 to the left a 1 4 turn and pull down 4 Insert new filter cartridge 1 back into the filter head 2a and rotate towards the right a 1 4 turn to lock filter into place Ensure that the LOCK arrow located in the middle of the filter cartridge corresponds with the downward arrow on the filter head 5 Turn cold tap to ON position Turn water supply ON slowly at isolation tap or water meter Note air may be purged from the filter system at this time 6 Check for any leaks and fix if necessary f Leave tap on to allow water to flush through the system for approximately 5 minutes You may wish to collect the water for use in the garden Note Tiny air bubbles being expelled from the cartridge will cause the water supply to appear cloudy this is normal This condition will clear itself over use or you may flush water through the system until water appears clear 8 Your A
3. Replace the filters A 12 month change out period is recommended Replace filters High sediment levels can cause premature clogging Replace filter See system specification for working pressures and consult a qualified plumber Refer to page 6 Tubing Installation and re install fittings amp page 3 Typical Installation Diagram The use of a tube cutter is recommended Open Cold water isolation tap or open mains water supply water Ensure the filter canister is fully inserted to filter head Ensure that the LOCK arrow located in the middle of the filter cartridge corresponds with the downward arrow on the filter head Performance Data Sheet Important Notice Read this data sheet and compare the Capabilities to your actual water treatment requirements The performance of this product has been verified and substantiated as the test data below summarises These substances may not be in your water Substance Average Influent ied um Chlorine Taste amp Odour 2mg L 15 Particulate Class um N A 85 Turbidity 11 45 NTU lt 1 0 NTU Cyst N A 99 9 To a capacity of 10 000L Replacement component AQP RFW 1 This system requires regular replacement of the filter cartridge to maintain proper operation Performance will vary based on local water conditions 2 This system must be installed according to local plumbing codes on the cold water line Average product water concentration Average Reduction Max Ef
4. e otherwise warranty will be void SAFETY PRECAUTIONS Warning It is essential that these Installation and Operating Instructions be strictly observed for correct operation of this appliance We recommend a qualified licensed plumber install the system who is prepared to guarantee their workmanship Prior to installation check for any existing State or Local Plumbing Codes to ensure installation is compliant INSTALLATION AND OPERATING INSTRUCTIONS 1 p AQUAPORT GOOD WATER MADE EASY INSTALLATION INSTRUCTIONS A Component identification and content check list Model AQP FKW Full Flow Water Filtration System Ref Description Qty Cartridges 1 Carbon Filter 1 Assembly Head 2a Filter head 1 2b Mounting Bracket 1 26 3 8 quick connect inlet 1 2d 3 8 quick connect outlet T Other Components 3 3 8 Tubing x 2 metres 1 4 Brass Dual Check Valve 1 5 Female 1 2 thread to 3 8 push in fitting 1 6 3 8 push in fitting to male 1 2 thread fitting 1 Screws for mounting bracket 2 not shown 2 INSTALLATION AND OPERATING INSTRUCTIONS 2a 2C f 20 20 3 Qa 5 6 1 NOTE Filter head 2a will come with small plugs in the inlet 2c outlet 2b to protect the svstem during shipping These plugs are to be removed before installation Tvpical Installation Diagram Cold Mains Water Isolation Outlet Brass Dual Check Valve Female 1 2 thread to 3 8 push in fitting D 3 8 tub
5. e intended purpose 4 The warranty does not cover use of this product where water is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system 5 The warranty does not cover damage to the product caused by accident fire or floods 6 Proof of purchase is required for warranty claims Please keep purchase receipt in a safe place To enable us to register your warranty and provide service should a problem occur we recommend you register your warranty online at www aquaport com au warranty Aquaport Corporation Pty Ltd 5 John Street Flinders Park South Australia 5025 Customer Care 1300 764 325 INSTALLATION AND OPERATING INSTRUCTIONS 11 AQUAPORT GOOD WATER MADE EASY 12 INSTALLATION AND OPERATING INSTRUCTIONS INSTALLATION AND OPERATING INSTRUCTIONS 13 AQUAPORT GOOD WATER MADE EASY CUSTOMER HOTLINE 1300 764 325 Aquaport Corporation Pty Ltd PO Box 81 Findon SA 5023 Australia Telephone 1300 764 325 Facsimile 08 8354 0722 Email aguaport aquaport com au Web www aquaport com au
6. fluent lt O 1 gt 99 lt O 1 N A 99 8 N A 0 1 NTU gt 99 0 1 NTU N A 99 9 N A This product complies with AS NZS 3497 amp AS NZS4348 for the following water treatment processes Treatment and Tests Table C1 Class Treatment Type Microbiological status bacteriostatic li Microbiological treatment li a Bacteria removal li b Virus removal li c Protozoa removal lii Turbidity amp particulate reduction lv Taste amp odour reduction V Chemical treatment Function Pass Will stop bacteria increasing but will not remove N A them unless ii a is ticked Will remove or inactivate bacteria N A Will remove or inactivate virus N A Will remove or inactivate cryptosporidium amp giardia Pass Will reduce cloudiness Pass Will reduce taste and odours Pass Will decrease chlorine compounds Pass INSTALLATION AND OPERATING INSTRUCTIONS 9 AQBUAPORT GOOD WATER MADE EASY Your Aquaport 12 Month Repair or Replacement Warranty Aquaport warrants this appliance to the first purchaser and subject to the stated conditions Warranty covers any defects in material or workmanship in the manufactured product within the first twelve months from the date of purchase To make a warranty claim you must call Aquaport on toll free number 1300 764 325 for instructions If a product is found to be faulty there is a 90 day return policy from the date of purchase Product returned to store MUST be accompanied by a valid p
7. ing 3 8 push in fitting to male 1 2 thread fitting Cold Water Flexible Line To Cold Tap Outlet WARNING Where water pressure exceeds maximum recommended working pressure a WaterMarked approved Pressure Limiting Valve must be installed prior to the filter system lt Cold water line INSTALLATION AND OPERATING INSTRUCTIONS 3 AQBUAPORT GOOD WATER MADE EASY INSTALLATION GUIDE Preferred installation utilising existing water supply and flexible cold water hose is shown on Page 3 Note Plumbing connections may vary please consult a qualified plumber for correct installation method for your home 1 Water Supply Installation a Locate cold tap water pipe and turn water supply off at the isolation tap If no isolation tap is available turn water off at the meter Turn on tap at sink to ensure water is turned off and to drain the pipe b Remove the flexible cold water hose that connects the cold water faucet to the cold mains connection Some water may spill out c Wrap plumbing tape around cold water stud in a clockwise direction Note Do not apply plumbing tape in a counter clockwise direction it releases the plumbing tape and leaks may occur d Hand tighten the brass dual check valve 4 to the mains cold water stud please see Fig 1 Water flow should be in the direction of the arrow on dual check valve Finish tightening with an adjustable wrench Be careful not to over tighten as cr
8. ntain filterable cysts This unit should only be used with water that has been adequately chlorinated or disinfected For use with ambient water only System Specifications Full Flow Water Filtration System Flow Rate Up to 4 7L pm Working Pressure 207 862kPa Temperature 1 38 C Service Eire 12 months Capacity 10 000L Flushing 5 minutes If the Aquaport water filter system has not been used for over 48 hours 1 to 2 litres of water will need to be flushed through the system before the water is used The Aquaport water system has a maximum and minimum water supply pressure limits The water supply pressure must not exceed the maximum and minimum water supply pressure limits specified in the Systems Specifications for your system Where water pressure exceeds maximum recommended working pressure a WaterMarked approved Pressure Limiting Valve must be installed prior to the filter system FILTER REPLACEMENT INTERVALS It is recommended that the filter cartridge is replaced within 12 months or 10 000 litres whichever occurs first Register online at www aquaport com au Dependent on water quality and the volume of water being filtered the life and performance of a cartridge may vary If you notice a reduction in volume or flow from the filter faucet or return of an unpleasant taste odour to the filtered water the filter cartridge s will need replacing Note Use only original Aquaport cartridges suitable for this applianc
9. o make sure there are no cuts nicks flat spots or sharp edges If any of these are present re cut the end with a tube cutter or utility knife The cut must be perfectly straight with no angle otherwise leaking from the connections may occur Note To remove tubing push collet against the face of fitting and remove the hose with collet still held against fitting face Fig 3 6 INSTALLATION AND OPERATING INSTRUCTIONS 4 System Start Up a Turn cold tap to ON position Turn water supply ON slowly at isolation tap or water meter Note air may be purged from the filter system at this time b Check for any leaks and fix if necessary If leaks are present connections may need to be reinstalled c Leave tap on to allow water to flush through the system for approximately 5 minutes You may wish to collect the water for use in the garden Note Tiny air bubbles being expelled from the cartridge will cause the water supply to appear cloudy this is normal This condition will clear itself over use or you may flush water through the system until water appears clear d Your Aquaport water filtration system is now ready to produce refreshing great tasting water for you and your family Push Collet 25 Pull Tubing FILTER REPLACEMENTS System Cartridge Cartridge Cartridge Model Replacement Replacement Service Life Pack Model Name Replace Replacement every 12 AQP FKW AQP RFW Filter for months
10. oss threading and leaking can occur 4 INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT It is a legal requirement under Australian Plumbing Standards that the Dual Check Valve be installed If this part is not installed all warranties are null and void e Wrap plumbing tape around male thread of brass dual check valve 4 in a clockwise direction f Hand tighten the Female 1 2 thread to 3 8 push in fitting 5 to the male thread of brass dual check valve 4 g Wrap plumbing tape around the male thread of the 3 8 push in fitting to male 1 2 thread fitting 6 ina clockwise direction h Hand tighten the 3 8 push in fitting to male 1 2 thread fitting 6 onto the female thread of the existing cold water flexible hose connected to the tap water line 2 Mounting Filtration Svstem Note Filter head 2a will come with small plugs in the hose Inlet 2c and outlet 2d to protect the svstem during shipping a Pick alocation under the sink to mount the svstem These plugs are to be removed before installation Location should be easilv accessible with clearance at the top and bottom of the filter to allow ease of removal of filter cartridge Please ensure there is enough space on either side of the svstem for the tubing connections See Fig 2 WARNING On the Filter Head 2a there is an arrow that indicates the direction of water flow into and out of the filter head When vou mount the filte
11. quaport water filtration system is now ready to produce refreshing great tasting water for you and your family Note Use only cartridges suitable for this appliance Please check system again the next day after installation for any leaks INSTALLATION AND OPERATING INSTRUCTIONS 7 AQUAPORT GOOD WATER MADE EASY TROUBLE SHOOTING BEFORE YOU CALL FOR SERVICE PLEASE REVIEW THE TROUBLE SHOOTING TIPS FIRST Problem Water contains tiny black particles Water appears milky or has air bubbles and is cloudy Chlorine taste and or odour in the product water Dispenses water very slowly Water leaking at fittings No water dispensing from system 8 INSTALLATION AND OPERATING INSTRUCTIONS Possible Causes New filter contains activated carbon which is food grade safe Air in the system The filter canister is no longer removing chlorine from the water supply The filter has been installed for too long The filter canister has become clogged Water Flow rate is dependant on mains water pressure Tubing may not be installed properly Cold water isolation tap or mains water supply may be turned off Filter canister not fully installed What To Do Turn on the water faucet and allow these harmless carbon particles to purge from the canister Turn off water faucet when water is clear Flush water through system until water appears clear or use the system and this condition will clear itself
12. r vou must ensure that the water flow will run in the direction of the arrow b Rotate the filter cartridge 1 towards the left by a 1 4 turn and pull filter down c Check to ensure that mounting bracket 2b is attached to filter head 2a d Mark location of fixing holes and fix unit to cupboard with mounting screws provided Note Remember to allow approximately 100mm above and below and 200mm on the sides of the filter cartridge to allow ease of filter cartridge change e Insert filter cartridge 1 back into the filter head 2a and rotate towards the right a 1 4 turn to lock filter back into place Ensure that the LOCK arrow located in the middle of the filter cartridge corresponds with the downward arrow on the filter head 2E e o o 3 3 INSTALLATION AND OPERATING INSTRUCTIONS 5 p AQUAPORT GOOD WATER MADE EASY 3 Tubing Installation The Filtration System has been supplied with quick and easy to install quick connections a Measure a length of 3 8 tubing 3 to run from the Female 1 2 thread to 3 8 push in fitting 5 to the filter head inlet 2c and another length of tubing to run from the filter head outlet 2d to the end of the cold water flexible hose connected to the tap b Install the tubing as per the installation diagram on page 3 To install tubing push tubing into connections and give a slight pull to ensure tubing is secure Note check the end of the tubing t
13. roof of purchase and Customer Reference number received from Aquaport Call 1300 764 325 For warranty claims outside of 90 days from date of purchase product will be repaired or replaced at our discretion Repair or replacement costs of the product will be covered under warranty by Aquaport Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired Refurbished parts may be used to repair the goods Warranty does not cover filter cartridge which is a consumable unless proven to have defects in material or workmanship in the manufactured product Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a major failure Register your warranty online at www aquaport com au warranty 10 INSTALLATION AND OPERATING INSTRUCTIONS Conditions Of This Warranty 1 This product has been fully installed in accordance with the user manual installation instructions 2 The warranty extends only to repairing or replacing any component that proves to be defective in material or workmanship 3 The warranty does not cover defects occasioned by misuse alterations accidents or used for other than th
Download Pdf Manuals
Related Search