POWERED WHEELCHAIR
Contents
1. support to the controller fixing cover beside the armrest adjust the position of the controller and fasten the screw nut See illustration 5 GIMA 2 Connect the connector labeled LEFT of the controller with the left one of the motor Connect the connector labeled RIGHT of the controller with the right one of the motor See illustration 6 6 Powered Wheelchair Operation 1 Turn on the power supply switch I O then the power indicator light is on When the first atta power volume indicator light on the right is on it means the power is enough 2 The driving speed can be adjusted by the ILLUSTRATION 6 speed adjust knob on the controller The low starting speed is suitable 3 Hold the handle to start slowly Push the handle forward the wheelchair moves forward move the handle to the left it moves to the left move the handle to the right it moves to the right move the handle backward it moves backward 4 Press the trumpet button to make alarm 7 Push By Assistant When the power is not enough move the clutch switch the wheelchair release the brake it can be pushed by assistant See illustration 7 8 Charge 1 Please charge the battery with specified charger coming with the powered wheelchair for safety Plug the outlet of the charger into the charge jack in the back of the controller 2 Plug the outlet of the charger in the suitable power supply 3 The power indicator is on and the charg2. E 1 MAIN PARAMETERS 1 Outer Dimension 1020 L X650 W X990 H mm 10 Over Obstacle 40mm 2 Light 24V 5W 11 Stop Distance 1m 3 Net Weight 50kg 12 Running Distance 20km incl Batteries Per Charging 4 Capacity Max 110kg 13 Noise lt 65dBA 5 Castor Diameter 200mm 8 14 Power Spec 2x12V 24V 24Ah 6 Driving Wheel 330mm 12 5 15 Get Over Channel lt 100mm 7 Seat Width 400 L x410 W mm 16 Motor Spec 168Wx2 8 Speed 0 6km h 17 Charging Current 3 5A 9 Creeping Capacity 127 18 Charging input AC 220V 2 Battery Installation When the batteries need to change put two new storage batteries to the same direction in the battery box Connect the anode of A battery and the cathode of B battery with a short wire Connect the anode of B run with the red short wire and the cathode of A battery with the blue short wire Then cover the battery box ILLUSTRATION 4 3 Battery Box installation 1 Open the wheelchair lift the battery box then hang the hooks of the box to the battery box support pole 2 Connect the power connector of the controller with the one of batteries box 4 Backrest angle adjusting You would better adjust the backrest angle before using the wheelchair or do this operation by assistant Just unscrew the adjustable knob choose the right angel you want fasten the knobs after any adjustment See illustration 4 ILLUSTRATION 5 5 Controller Installation 1 Insert the controller
3. M27729 EN Rev 0 07 11 Gima S p A Via Marconi 1 20060 Gessate MI Italy Italia tel 199 400 401 fax 199 400 403 Export tel 39 02 953854209 221 225 fax 39 02 95380056 j gima gimaitaly com export gimaitaly com PROFESSIONAL MEDICAL PRODUCTS www gimaitaly com POWERED WHEELCHAIR User Manual ATTENTION The operators must carefully read and completely understand the present manual before using the product Fabbricante Manufacturer C E Gima S p A Gessate MI Italy Made in PR C OGIMA I PRODUCT INTRODUCTION The powered wheelchair is easy to use The user can make the powered wheelchair move forward backward or turn round and round in the same place only by the controller When Handie the power is not enough it can be used as the transit wheelchair The seat cushion is detachable ILLUSTRATION 1 Armrest Controller Anti tipper__ f D Accessories Charger 1 pc storage batteries 2 purchase Power wheel Castor Footrest Ii INSTALL AND USE 1 Chair Frame Installation 1 Remove the footplate just adjust the locker then swing the footplate to the side pull up the footplate until it is out of the chair frame fully 2 Put the footplate to the chair frame by side push it towards the wheelchair until it is locked firmly in the chair frame See illustration 2 3 Install the anti tiper and insert the pin See illustration 3 ILLUSTRATION 2 ILLUSTRATION 3 GOGIMA 2 TABL
4. ber in the list which matches the number of flashing bars and follow the instructions If the problempersists after you made the checks described above contact your service agent GINA TROUBLESHOOTING GUIDE number The battery needs charging or there is a bad connection to the battery Check the connections to the battery If the connections are good try charging the battery The left hand motor has a bad connection Check the connections to the left hand motor The left hand motor has a short circuit to a battery connection Contact your service agent The right hand motor has a bad connection Check the connections to the right hand module The right hand motor has a short circuit to a battery connection Contact your service agent The wheelchair is being prevented fromdriving by an external signal The exact cause will depend on the type of wheelchair you have one possibility is the battery charger is connected A control systemfault is indicated Make sure that all connections are secure The parking brakes have a bad connection Check the parking brake and motor connections Make sure the control system connections are secure An excessive voltage has been applied to the control system This is usually caused by a poor battery connection Check the battery connections A joystick fault is indicated F Make sure that the joystick is in the center position before switching on the control system A comunica
5. e ILLUSTRATION 8 indicator is on charge begins 4 When the charger indicator is on the power of the battery is sufficient The charge time depends on how much power is left in the battery A newstorage battery needs to charge 12 14 hours for the first time After charge take out the outlets of the power supply and charge output 9 Lighting lamp Operate the on off button to turn on or turn off the lighting lamp The button is under the armrest See illustration 8 GOGIMA 10 Slow or sluggish movement If the wheelchair does not travel at full speed or does not respond quickly enough and the battery condition is good check the maximumspeed setting If adjusting the speed setting does not remedy the problemthen there may be a non hazardous fault Contact your service agent 11 Locking Unlocking the wheelchair The VR 2 control systemcan be locked to prevent unauthorized use The locking method is via a Sequence of key presses and joystick movements as detailed below To lock the wheelchair e While the control systemis switched on depress and hold the on off button e After 1 second the control systemwill beep Now release the on off button e Deflect the joystick forwards until the control systembeeps e Deflect the joystick in reverse until the control systembeeps e Release the joystick there will be a long beep e The wheelchair is now locked To unlock the wheelchair e Use the on off button to switch the cont
6. e to outside agents such as voltage changes electro magnetic fields radio interferences etc The warranty is void if the above regulations are not observed and if the serial code if available has been removed cancelled or changed The defected products must be returned only to the dealer the product was purchased from Products sent to GIMA will be rejected
7. rol system on The maximum speed profile indicator will be ripping up and down e Deflect the joystick fowards until the control system beeps e Deflect the joystick in reverse until the control systembeeps e Release the joystick there will be a long beep e The wheelchair is now unlocked A REMARKS The six lights of the indictors indicate the power volume The wheelchair can be charged when the third yellow light on the left in the control box is on The power is exhausted when the second red light on the left is on please charge immediately otherwise the battery will be damaged and cant be charged 2 In order to make the battery more durable please charge the battery frequently to make it sufficient If the wheelchair is not used take out the battery after it is charge enough If the wheelchair is not used for a long time charge the battery once three months GIMA 3 The power wheelchair is suitable to drive in wide room path and flat road around residences Don t go close the motor vehicles deep holes and water 4 Don t run across the steps often in order to avoid damage of the front castors 5 Don t climb long slope in case the circuit of the motor is overload and the power is used too fast or accident happens if the user cannot stop the wheelchair in time in the middle of the slope 6 The accessory castors uses in case the wheelchair is overturn when the slope is too inclined Don t detach them 7 When it is neces
8. sary to stop the wheelchair during driving move the handle of the controller to the original position and it will brake automatically When stop the wheelchair on the slope it can brake automatically to stay on the slope 8 Please see whether the air in the tyres of the front castors and rear wheels are sufficient before use If it is not sufficient please inflate the tyres in time The air pressure should be 3kgf cm2 4kgf cm2 9 Please check whether the connectors connect one another well the strew nuts are loose Adjust them in time 10 If need to fold the wheelchair take out the electric connectors and the battery box and pull up the middle of the upholstery to fold it 11 If need to disassemble the controller take out the connectors of controller with the motors and batteries release the adjusting knob then the controller can be taken out from the cover 12 Heavy patient and mental illness are inadequate to use the electric wheelchair 13 Because the backrest can automatically recover to the original position if nobody is on the wheelchair under the lying position please don t pull the backrest adjusting lever MAINTENANCE Clean every part of the wheelchair frequently SELF HELP GUIDE If a systemtrip occurs you can find out what has happened by counting the number of bars on the battery gauge that are flashing Belowis a list of self help actions Try to use this list before you contact your service agent Go to the num
9. tion fault is indicated Make sure that joystick cable is securely connected and not damaged domestic waste The users must dispose of this equipment by bringing it to a specific recycling point for electric and electronic equipment For further information on recycling points contact the local authorities the local recycling center or the shop where the product was purchased If the equipment is not disposed of correctly fines or penalties may be applied in accordance with the national legislation and regulations X Disposal The product must not be disposed of along with other ne GIMA WARRANTY CONDITIONS Congratulations for purchasing a GIMA product This product meets high qualitative standards both as regards the material and the production The warranty is valid for 12 months from the date ofsupply of GIMA During the period of validity of the warranty GIMA will repair and or replace free of charge all the defected parts due to production reasons Labor costs and personnel traveling expenses and packaging not included All components subject to wear are not included in the warranty The repair or replacement performed during the warranty period shall not extend the warranty The warranty is void in the following cases repairs performed by unauthorized personnel or with non original spare parts defects caused by negligence or incorrect use GIMA cannot be held responsible for malfunctioning on electronic devices or software du
Download Pdf Manuals
Related Search