Vehicle GPS Tracker JV200 User Manual
Contents
1. 12 24V Relay 4 5 Power ACC Tele cut off petrol electricity control cable 4 pin 1 Device standard power supply 9V 36V DC please use the original factory supply power cord red is positive black is negative During installation power negative please should be independently grounded do not connect with other ground wire 2 The ACC line orange connects to ACC switch of the vehicle Please make sure to connect the ACC wire otherwise the device will enter ignition detection status when disconnect the ACC line If you don t need to anti theft temporarily just connect the ACC line to the positive side in parallel 3 Tele cutoff petrol electricity control line yellow is connected to pin 86 of the Tele cutoff petrol electricity relay equal to the yellow line of the relay socket 5 Quick Operation Instructions To properly use the device common parameters should be set before initial use This can be done by using the parameter editor or by sending SMS commands to the device should be English comma and no space before and after the comma 5 1 Add SOS number SMS command to the device to add the SOS number SOS A No 1 No 2 No 3 A means to add new numbers for example SOS A 18165542975 18165542976 18165542977 It will reply OK SOS1 18165542975 SOS2 18165542976 SOS3 18165542977 after set successfully 5 2 APN setting To connect default platform www jimishare com please send the2. the device Any damages by misuse are not covered by the warranty 4 3 Install the device You need to choose somewhere that it won t be found because the whole point of fitting covert GPS vehicle tracker is the secrecy element 1 Your device has built in GSM antenna and GPS antenna During installation please make sure the receiving side face is up any high power devices such as reversing radar anti theft device or communication equipment would affect the signal of the device 2 All metallic cases of the windshield will attenuate the signal on the tracking device It s simply due to the shielding effects of the metal compound of the case 3 The device should be fixed into position with cable ties or wide double side tape Installation please refers to below picture Under rear windshield Under the dash board below ee the front windshield front windshiel Under rontwindshipi In the parcel shelf in the rear In the front bumper non material face make sure the device does not get wet Under the wiper version non metal make sure the device does not get wet Non Covert Installation fix the device on the dash board below windshield A Device Wiring 1 The standard voltage is 9V 36V the red wire is the positive the black wire is the negative 2 Connect the black wire to ground 3 Wiring diagram Storage battery 12V 24V Black Orange
3. Jimi Vehicle GPS Tracker JV200 User Manual Version J1409 1 0 www jimilab com Thanks for purchasing this Jimi JV200 This device will provide you high quality GPS tracking service based on Jimi s exceptional technology and standards This user manual has been specially designed to guide you through the functions and features of your JV200 Please read this manual carefully before using your device to ensure safe and correct use The descriptions of this manual are based on the default setting of JV200 Tips Choose a rate plan wisely Your JV200 can use up Internet bandwidth really quickly Before you use your JV200 we strongly recommend that you talk to your mobile operator about data rates If you re on a standard data plan the costs could really add up Switching to a flat rate plan could be a lot cheaper Popular Uses Fleet Management Track your fleet easily View up to 15 000 units from a single map Investigators and Law Enforcement Get the real time location evidence you need Vehicle Owners Use for vehicle theft and recovery efforts Features and Benefits No Battery Life Concerns The unit is hardwired to your vehicle s battery 10 Second Location Updates The FASTEST location updates Web Based Tracking No software to install view location data from any web browser Track Up to 15 000 Devices on a Single Account Perfect for fleet management Extremely Accurate Utilizes GPS and GSM C
4. SMS command below APN command format APN APN namef or APN APN name user name password Example APN CLENTE or APN ORANGE ORANGE ORANGE An automatic reply OK will be sent in one minute if setup is successful 5 3 Server setting To connect other platform please send the SMS commands below Command format SERVER 1 domain Port O Example SERVER 1 www jimishare com 8841 0 It will reply OK after set successfully 5 4 Set the center number If you want to cut off restore oil by SMS command you have to set a center number firstly Only the center number can send the cut off restore oil command to the device You can set your own mobile number as center number The command for setting center number is CENTER A mobile number For example CENTER A 18165542976 If set successfully there is an OK reply message A Only the SOS number can be used to add or delete center number successfully There is only one center number can be set 5 5 GPRS time interval Users can modify GPRS time sending interval by SMS TIMER 11 T2 T1 ranges 5 18000 or O seconds upload interval when ACC ON 0 means no upload default is 10 T2 ranges 5 18000 or O seconds upload interval when ACC OFF 0 means no upload default is 10 5 6 Vibration alarm delay time setting Delay time for device entering vibration alarm state after the vehicle power is off and ACC is in low level In the vibration alarm state if the vehicle vibrates
5. Sensitivity 144dBm Position Accuracy 10m Cold Start lt 38s TTFF Open Sky GSM GPS Antenna LED Indicator GSM GPS Antenna Built in design LED Indicator GSM green GPS blue Power red Data Transmit TCP SMS Non movement Detection Movement alarm based on built in 3D motion sensor Mileage Report Track by time distance interval 4 Getting Started Get started by assembling and setting up your device for its first use To remove the back cover e Firmly hold the device with both hands and the front panel facing down e Push the back cover up with your thumbs until it disengages from the device and then slide it up to remove 4 1 Install SIM card 1 To install the SIM card e Locate the SIM card slot and then insert the SIM card with its gold contacts facing down and its cut off corner facing out the card slot e Slide the SIM card completely into the slot e After SIM card installed please switch the power on A Make sure there is enough credit on the SIM card If you will be using the GPRS function you should pay attention to the current SIM card GPRS charge 4 2 Charge the device Covert installation Plug the device connector into a charging cable The charging cable with 2A FUSE for short circuit over current protection A Improperly connecting the charging cable can cause serious damage to
6. Server 1 www gpsluckly com 88 0 platform information URL http maps google com maps q _ preset web link setting information 6 Operation of device 6 1 Power on Power off Power on Once insert a valid SIM card and connect all the wires turn on the device then Power LED will flash first during signal searching process GSM and GPS LED will flash Once GPS LED keeps slow flashing it means the device has been located and it starts to work Power off Just turn off the power switch The device will begin to upload positioning data to server once inserting a valid SIM card and power on During the working time it can upload data to server every 10 seconds A To power on power off please remove the back cover first refer to 4 Getting Started 6 2 Check location 1 Via SMS 1 1 SMS WHERE to the SIM number of device The device will send a location message automatically You can get the coordinates If the device does not search any information of location it will send No data to the cell phone Example Current position Lat N22 577156 Lon E113 916748 Course 131 99 Speed 0 00Km h Date Time 2013 10 08 17 35 32 1 2 SMS URL to the SIM number of device The device will send a location Google Map link If the device does not search any information of location it will send No data to the cell phone Example lt 10 08 17 36 gt http maps google com maps g N22 577156 E113 916748 2 Via platform Go
7. e alarm will be activated in the next 3 minutes if vehicle power is still off ACC status is low device will activate vibration alarm The device will then send an alarm message to the platform also another SMS vibration alarm message to the preset SOS number Example Sensor Alarm lt 11 23 14 53 gt http maps google com maps g N22576713 E113 916585 A1 The SOS numbers should be preset 2 Send SENALM OFF to turn off the vibration alarm if don t need 6 6 Oil cut off 1 via platform Send oil cut off command on platform To make sure the security of vehicle tracker can only indicate to cut off oil when GPS is in valid position status and the speed is less than 20KM H or in static Platform account password is needed when sending oil cut off command 2 Via SMS Firstly you should set a center number Please refer to 5 4 Only center number can send the command to the device to cut off and restore oil The format is RELAY 1 After the command is carried out it will reply Cut off the fuel supply Success Speed 0 Km h If the command didn t carry out it will reply the reason about fail to carry out A To ensure the safety of the driver and the car this command is valid only under two conditions the GPS is located the speed is less than 20km h 6 7 Restoring Oil 1 Via platform When the alarm is off sending recover oil commands manually Device will restore oil supplying and vehicle will work normal
8. ell Towers for super accurate location data Detailed Reporting View Save and Print detailed driving data up to 90 days history Introducing your JV200 Learn about your device s layout indications and specifications 1 Inside the Box Check your product box for the following items e Device e Charging Cable e User Manual 2 JV200 Overview GSM indicator green GPS indicator blue Power indicator red LED Indicators Power indicator red Indication Flashing Power on Solid red Not working properly OFF Power off GPS indicator blue Indication Quick Flashing 0 1s on 0 1s off Searching GPS signal Solid blue GPS fixed OFF No GPS fixed or initializing GSM indicator green Indication Quick flashing 0 1s on 0 1s off GSM initializing Flashing 0 1s on 2s off GSM signal received Solid green Connected to GPRS network OFF No GSM signal LED indicators have two modes 1 Hidden Mode All indicators would turn off automatically by pressing LED controller 2 Continuously Bright Mode Indicators would never turn off if the device is working 3 Specifications Dimension 86 6 L x 44 W x 13 6 H mm Weight 50 5g Operation Temperature 20C 70C Operation Voltage 9 36vDC Humidity 20 80 GSM Frequencies 850 900 1800 1900 MHz GPRS Class 12 GPS Sensitivity 159dBm Acquisition
9. for a few times it will activate the vibration alarm system If the vehicle battery is still not on ACC is in low level after 3 minutes the device will start vibration alarm SMS format DEFENSE TIME The time ranges from 1 to 60 minutes default is 10 1 Preset SOS numbers before sending SMS alarm messages and calls 2 If there is no need for vibration alarm please SMS SENALM OFF to close it 5 7 Check parameter setting You can check the parameter setting by command PARAM Example PARAM Information replied IMEI 353419032348877 IMEI number of the device TIMER 10 10 GPS data uploading Interval SENDS 5 the GPS working time when ACC is OFF SOS 18165542976 SOS numbers maximum 3 SOS numbers can be set and used for alarm and monitoring Center Number 18165542976 only 1 center number can be set and used for cutting off restoring oil command Sensoralm 10 5 1 180 detect 5 vibrations in 10s the alarm delay is 180s Defense time 10 the vibration alarm delay is 10 minutes TimeZone E 8 0 time zone info The replied information contains IMEI number GPS data uploading Interval GPS working time SOS number center number sensor time interval vibration alarm delay and time zone info 5 8 Check GPRS parameters SMS command format GPRSSET Example GPRSSET Reply message GPRS ON IGPRS on off status Currently use APN CMNET user password APN setting information
10. ly again Platform account password is needed when sending oil cut off command 2 Via SMS Only center number can send the command to the device to restore oil The format is RELAY 0 After the command is carried out it will receive Restore fuel supply Success 6 8 Over Speed Alarm When the car is moving over a limited speed in average in a limited time period then the device will send over speed alarm SMS to user To turn on the over speed function please send below SMS command SPEED ON Time Limited speed way of alarm Time range Second 5 600s default as 20s Limited speed range km h 1 255 default 120 Way of alarm 0 GPRS only 1 SMS GPRS default 1 Example SPEED ON 10 120 1 Means when the car is moving over 120km h in average in 10 seconds the device will send over speed alarm to user 6 9 Restore to factory setting SMS command format FACTORY to set all parameter to default factory value Once received OK it succeeds 6 10 Reboot device When there is something wrong with the link of GPRS e g the parameter setting of the device is correct but you can t track the car on the platform At this moment you can send a command to the device to reboot the device The format is RESET After receiving this command the device will reboot after 1mins 7 Register and log onto GPS tracking platform www jimishare com Account IMEI Number The function on the GPS platform can be realized as f
11. nd overheating Correct disposal of this product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking in the battery manual or packaging indicates that batteries on this product should not be disposed of with other household waste at the end of their working life If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect the natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system
12. ollows e Real time Tracking e Report and Statistics e Online Configuration 8 Troubleshooting If you are having trouble with your device try these troubleshooting procedures before contacting a service professional Problems Causes Solutions Red LED does not work when power connected The fuse blows Replace the fuse Fail to connect network Wrong installation of SIM card Check SIM card installation gt 4 1 Install SIM card Filth on the SIM card iron surface Clean it Useless SIM Contact internet service provider Improper installation Check installation of device gt 4 3 Install the device Beyond GSM service area Bad signal Use it in effective GSM service offer area Try again in a better signal area Fail to charge The voltage is unsuitable Connect with power with suitable voltage Improper connection Check connection with charger Safety Precautions Handle and dispose of batteries and chargers with care Use only JIMl approved accessories specially designed for your device Incompatible accessories can cause serious injuries or damage to your device Never place batteries or devices on or in heating devices such as microwave ovens stoves or radiators Batteries may explore when overheated Never crush or puncture the battery Avoid exposing the battery to high external pressure which can lead to an internal short circuit a
13. to the platform website offered by dealers to check your vehicle location 6 3 Wire cut off alarm When the electricity supply of device is cut off it will activate cut off alarm In this case the device will send related SMS to the specific numbers and dial the numbers in circles If nobody answers the call just keeps 3 loops at most At the meantime the device will upload SOS alarm data to the server And it will send Cut Power lt Date Time 13 06 17 14 53 06 gt http maps google com maps g N22576713 E113 916585 A The specific numbers should be preset please refer to 5 1 6 4 Low battery alarm When the device is only working with battery once the internal voltage of battery is less than 3 7V device will send low battery alarm SMS to specific number and alarm on platform Low battery alarm SMS content example Attention Battery is too low please charge Which means the battery is too low inform user charging it in time The specific numbers should be preset please refer to 5 1 6 5 Vibration alarm The vibration alarm function is off by default To activate this function please send the following command SENALM ON The alarm will be sent to both the service platform and SOS numbers When vehicle power is off ACC status is low and if the lead time of low ACC is more than 10 minutes settable device will activate security alarm When the security alarm is on once the vehicle vibrates for several times th
Download Pdf Manuals
Related Search