1 Face Recognition Access Control & Attendance System User
Contents
1. s Number to modify the system will inspect the corresponding information in the database automatically press OK then enter the Modify User menu if that user number was not registered in the system prompt User is not existed Input again then the system is back to Input User No and waits for inputting again Modify Name The admin can change the User name after input correct user number and press OK to confirm User Manual Ver 2 6 26 Modify Method A Modify User When the user re enter the name then the system will let the user to choose verification method again About the detail options please see Verify Method Modify User Face Card Registration According to a method user chose then to do the face or card registration Modify Privilege The privilege can be changed in Modify Privilege There are three options which is Attendance and Access Attendance only or Access only User Manual Ver 2 6 27 Delete User Delete User Model In User Management menu press the corresponding number 3 to enter Delete User Model directly Delete User Apelete User Input User Number if the number is existed it will be deleted otherwise that information User is not existed will be shown on the screen and it will quit automatically Press OK to confirm Confirm Delete will be displayed and utter the hint voice press OK again to delete the se2. 20 80 Size 230 135 108mm L W H Weight 593g User Manual Ver 2 6 Installation Method Wall Hanging Terminal Blocks Description F810 has 4 groups of terminal blocks total 21 pins They are e 4 pin Sensor Group Pin definition o Pinl o Pin2 o Pin3 o Pin4 Door Sensor Switch Door Sensor GND Button GND User Manual Ver 2 6 74 5 pin Relay Group Pin definition Pinl Normally Open o Pin2 Common o Pin3 Normally Close o Pin4 GND o Pins 12V NC Lock NO Lock User Manual Ver 2 6 75 Y Caution When device connected with NO NC lock 1 Ifuse 12V 1A adaptor to supply power to device external power is required to power lock 2 If use 12V 3A adaptor to supply power to device device can supply power to lock which rated current less than 1 Ampere e 6 pin Wiegand Group Pin definition Pinl WDO OUT o Pin2 WDI OUT o Pin3 GND o Pin4 WDO IN Optional o Pind WDI IN Optional o Pin6 GND Optional 6 pin WDO OUT WD1 OUT GND WDO IN WD1 IN GND User Manual Ver 2 6 7 pin Alarm Group Pin definition Pinl Speaker Pin2 Speaker Pin3 Alarm COM need external power Pind Alarm NO need external power Pin5 GND Optional Pin6 TYPER_OUT Optional Pin7 TYPER IN Optional O O O e e e 1 Speaker am F m A Jl eu if 6 TYPER_OUT Alarm 7 TYPER IN External Power User Manual Ver 2 6 77 Caut
3. shown on the screen input user s ID Number in it as the following figure shown the device will inspect whether this user number is existed in the database or not Register User Input Name Input available Name in the following interface Text field can accept lower upper letters blank and dot characters Press MENU key can switch model between lower and upper letter User Manual Ver 2 6 21 L Register User Press OK to confirm and then press ESC to quit and return to the Function Menu After inputting user s name the system will switch to Verify Method screen About Verify Method please refer to following Verify Method 2 verifying methods can be chosen Face User or Card User Choose Face User methods the system will go to Face or Card and Face interface User Manual Ver 2 6 22 Register User Choose Card User methods the system will go to Card or Card and Photo interface Choose Card Card and Photo or Card and Face methods the system will request user to swipe the RFID card Press ESC to cancel card registration After finishing card registration the system will go to Face Register User dius Face recognition for normal user Card recognition for temporary user Card and Face recognition for high security level After Verify Method the system will go to face r
4. Check USB Test device USB port User should plug USB driver into the port before the test starts 2 Check USB IA Check USB Check SD Card Test device USB port User should plug SD Card into the reader User Manual Ver 2 6 67 before the test starts Check RFID Card Test device RFID Card reader When the test begins user should swipe the card in front of the RFID Card reader area For Common User Face Recognition After all users registered Face ID can be used When a user step towards the device about 0 5 meter the device will apperceive and startup face recognition function automatically face recognition interface will be shown on the screen it will be the color figure there is a green sector brush go around clockwise continuously and the green circle line frame will direct user to aim at sensors Face inspected successfully the green line frame will display on the screen and a green stick will scan user s image from User Manual Ver 2 6 68 top to bottom for recognizing your face On Duty Face recognition and user searching will be finished at the same time If face recognizing has continuous failed taken over 30 seconds system will return to the standby state interface During the recognizing process the system will provide some prompt information for user such as Please Get Closer Please Get Farther and Adjust Your Action On Duty I
5. this shift to define Press OK to confirm the setting and it will utter the correct hint voice 1 engineer Press Browse Work Code to inspect all work codes that have been set Press keys to choose other corresponding options and then User Manual Ver 2 6 56 press OK to operate this option or press the corresponding number key to operate the corresponding function directly amp dd Work Code Related Parameter Work Code ID Range 1 9999 Work Code Name 18 sheets per position dius If the user select Open Work Code model the user has to select corresponding work code after recognizing successfully User Manual Ver 2 6 57 7 Access Control Lock Driven Time 1 10s ASC The time of lock driven can be modified from 1 second to 10 seconds It depends on the time of door opening requirement Sensor Detect It can be turn on or turn off If the function 1s turned off the door cannot be monitored by device User Manual Ver 2 6 58 Sensor Type TPE None There are two types offering which are normally open NO and normally close NC Sensor Delay 1 99s Sensor Delay User Manual Ver 2 6 59 Alarm Setting E E ET isettine Removal Alarm Select open the alarm will startup automatically when the device is removed by anyone else select Close the device won t alarm when it is removed Reject Alarm when user get access failed 3 times the devic
6. Face Recognition Access Control amp Attendance System User Manual July 2010 User Manual Ver 2 6 Table of Contents Product OVGEVIeW nes 4 General TnirOduch On cass uoo ob or poe Ero Son Eri to os dde Das 4 laci ATE 4 D vic Conte duration pe ete o pe Ups quA tee Eva Ed bU B Installation Instruction 9 SICHER o en HUMEUR aeal lacouedencnedtvoamsrer access 11 Set Administrator and operation 13 Seb XCOTTEHSEEALOE 505 ie erc Mu te buie 13 Enter to Set Administrator Model sse 13 DeL dint SECAEOE 5 oco cocido Sodra liue ot Oto Sors 14 Modify or Delete Administrator eeessesesesse 16 Administrator Verification eese 18 Io tente uio Mh 7 010 np rp 19 Administrator Function Menu 20 User M TnaASeN NEs ns sand Len nn ne 20 Modi y Use nn 25 Deke USSR EP 28 Record Manacement eeno o ue 30 USB Manae ci iena 32 SU SEC SOELUITID ar utat eee nee seer etree 38 System Information 25 5 0 a nn 62 AMO TOS os dr Roos AN I EM eM UE 64 Pot Common USERS ibel pose uad eoe aa 68 User Manual Ver 2 6 Face Recognition 68 User No amp Face Recognition seen 70 Card Recognition 70 Card amp Face Recognition 70 Authentication Successfully 71 ui ne 73 Technology Specification ccccescccsesecceeeece
7. ata exported will form a new file named USER TXT in the USB flash driver Export All Users Press number 3 to export all users information and face images files During the exporting process the procedure percent will be shown on the screen There will be successful prompt information display when it finished and utter the correct hint voice After 2 seconds system will return to the Function Menu The data exported will form a new file named USERALL TXT in the USB flash driver Import Part Users Press number 4 to import the users information and face images saved in USER TXT file from the USB flash driver to the database in the device During the importing process the procedure percent User Manual Ver 2 6 will be shown on the screen The imported data will add up or cover the former data according to the Job Number There will be successful prompt information display when it finished and utter the correct hint voice After 2 seconds system will return to the Function Menu Import All Users Press number 5 to import the users information and face images saved in USERALL TXT file from the USB flash driver to the database in the device During the importing process the procedure percent will be shown on the screen The imported data will add up or cover the former data according to the User Number Import All Users Please Wait There will be successful prompt information display whe
8. be carried out After that the device will restart automatic System Setting System Setting Model In the function menu press the corresponding number 5 to enter User Manual Ver 2 6 38 System Setting model directly Press ESC to quit and return to the Function Menu interface System Setting diss When under system setting press OK to confirm the setting then do more settings If press ESC the setting will not be saved and the system will return to the System Setting menu System Setting 1 Set Date and Time x ystem Setting Date and Time User Manual Ver 2 6 3 9 Set Date and Time et System Time Input combined numbers in Y M D frames respectively cursor will jump to the next frame when user finished in the last frame cursor will wink in which it locate and inspect the number s validity automatically Press OK to confirm the time and the system will utter the correct hint voice it will return to the Set System menu after 2 seconds Press ESC the system will quit modification and return to the Set System menu The system time can be set into 9 formats in order to fit different countries time formal Set System Time Oset Date Format 2 Mis User Manual Ver 2 6 40 2 Set DST Daylight saving time DN MIC Input DST Start time and End Time in Month Day or Month Week format respectively Press OK to confirm th
9. ce Startup Following figure will be shown after power on the device it is also the standby interface Current date week time will be shown on the screen When record capacity reaches up to 85 capacity percent will be shown on the screen to remind the administrator At that moment the administrator should export or clear some data from the device User Manual Ver 2 6 11 If the SD card is not in the device the information of No SD will be shown on the screen MN MMA User Manual Ver 2 6 12 Set Administrator and operation Set Administrator Enter to Set Administrator Model First entrance Start the system at the first time the administrator has not been set yet Press MENU to enter Functions Menu and then press 1 to Set Administrator operation model the following picture will be shown on the screen a Set Admin hanwang pee 1 2 3 4 5 6 7 8 Y Caution Please set one administrator at least when start to use this device because for the security reason all operations need to be controlled by the administrator Normal entrance After setting an administrator press MENU to enter Administrator Verifying model function menu will be displayed after verification success User Manual Ver 2 6 13 Set Administrator Number of Administrators There are eight unset administrators in the system If an administrator is not set the Unset will be di
10. e Function Menu The records can be searched by ID or Name Choose one of them the Record Inquiry interface will be shown as below Input User ID or User Name and Start time End time to get users record Delete all Record Model In Record Management menu press the corresponding number User Manual Ver 2 6 3 2 to delete all Records The system will prompt user Cannot ie Recover press ESC to return to the Function Menu Press OK the record will be cleared the hint information will display as the following figure shown After that Finished will display the correct hint voice can be heard after 2 seconds the system will return to the Function Menu interface Auto Upload Select Auto Upload function to turn on or turn off records auto upload function If the status is on every attendance record will be transmitted to a server with specified IP address USB Management In the function menu press the corresponding number 4 entry the insert USB Disk interface Enter USB management model directly User Manual Ver 2 6 USB Management The record and user information can be imported or exported in this model Work code and status also can be imported from here The firmware can be upgraded directly via USB flash driver USB Import or Export Model o Under the system standby interface insert USB flash driver the system will sta
11. e last set volume level it will return to the Set System menu after 2 seconds Choose ESC the system will quit modification about the volume setting and return to the Set System menu User Manual Ver 2 6 43 4 Set Power Button S t Power Button Power Button Off The power button can control the button in the keypad whether available And device has an power on and off schedule There are two time points can be set One opening time and one closing time can control the device open and close automatically m Time 06 00 OKTAI1ime User Manual Ver 2 6 44 et Power On Time Set Power Off Time 5 Set Communication set Communication Network Setting Network Setting User Manual Ver 2 6 45 According to the direction of networking engineer to set IP address IP mask address and gateway address The host IP can be set for auto upload The record will be uploaded to User Manual Ver 2 6 46 this IP computer The communication password is not necessary That is used for increasing the security level The password will be inputted when the device connected with computer Network Setting Press OK to confirm the setting the complete networking information User Manual Ver 2 6 47 will be shown on the screen it will utter the correct hint voice and restart the device automatically Wiegand Output According to the direction of acces
12. e port Insert network cable in the network cable port the device will be connected with PC for any management operation with the software Installation Instruction Please drill four holes on the wall according to diagram below Installation Diagram SH3Bolt Ground User Manual Ver 2 6 j 1 Removal Alarm J 4 e Screw kaht Device installing diagram Unconnected with door controller Insert the standard power adapter plug into the power port which is placed at the left slot in the back of the device Connected with access controller Connect the cable with the terminal blocks through the backboard as the installation diagram shown Plug the RJ45 crystal port of network cable into the network cable port which is located at left top side in the back of device Install the Mounting plate the vertical distance could be 1 15 meters between the two below level holes and ground Fixed the Mounting plate on the wall and please ensure the backboard is horizontal and vertical from the ground and it need to be stuck on the wall User Manual Ver 2 6 Insert the fixing holes at the back of device into the protrude pins which are placed at the Mounting plate then press it down softly keep the device hanging on the Mounting plate and stick it with the backboard then fix the screw at the bottom of device Make sure all connection finished and correct then power on the devi
13. e time and the system will utter the correct hint voice Choose ESC the system will quit modification about time setting and return to the Set System Time menu Month Day Format input month date and time information for DST start time and end time For example DST starts from 2am on March 6 2010 to 2am on October 20 2010 and then the inputting will be User Manual Ver 2 6 41 Start Time 03M 06D 02h End Time 03M 06D 02h M Month D Day h hour Month Week Format Alternative DST input method User needs to determine in which month which week and which day is DST start time and end time For example DST starts from 2am in 3 Sunday on March 2010 to 2am in 1 Sunday on October 2010 and then the inputting will be Start Time 03M 03 W 07D 02h End Time 10M OIW 07 D 02h M Month W 1 1 2 2 3 3 4 4 and 5 Last Week D 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 5 Friday 6 Saturday 7 Sunday The system time will advance an hour when it comes to Start time and User Manual Ver 2 6 42 will recover when it comes to End time 3 Set Volume Set Volume Press the corresponding number key to choose High Middle Low Mute level or presst keys to shift the op tions then press OK to confirm the selection the device will utter the correct hint voice in th
14. e will alarm in order to make other attendance that someone may be unauthorized em Alarm 2g B NUES 3 FN WS The reject alarm times can be set from 1 to 9 times The alarm period is available from 1 second to 9 seconds User Manual Ver 2 6 60 Reject Alarm B Reject Alarm Sensor Alarm When the sensor find out the door do not be closed for the few seconds the alarm will work 8 Default Setting The caution information will display as the following figure shown Press ESC to cancel the operation and return to the Set System menu if press OK the system will be recovered to the default setting User Manual Ver 2 6 61 and Initializing Waiting will be shown on the screen After that Initializing finished will be shown and the correct hint voice can be heard the system will be restarted automatically Default Setting diss Default Setting means the system will clear all users information All attendance records and pictures all administrators and all setting will be lost and recovered to the default setting System Information System Information Model Enter the Function Menu press the corresponding number 6 to enter the System Information model directly In this model press ESC to quit and return to the Function Menu interface User Manual Ver 2 6 62 System Information Capacity Information Display the capaci
15. eeeceeeseeneeeens 73 Terminal Blocks Description sees 74 DO a TINmMT 78 Y Caution The functionalities and contents shown in this manual may different from the actual product please refer to the actual product Please forgive us to simplify some words because of limited display on the screen such as Admin refers to Administrator Recog refers to Recognition No refers to Number User Manual Ver 2 6 Product Overview General Introduction Face ID is industry first embedded facial recognition system with leading Dual Sensor Facial Recognition Algorithm FAR lt 0 0001 which makes facial recognition more faster and accurate different source light technology enable the system works well under different environment for access control and time attendance application Features Embedded facial recognition system Adopt US advanced DSP technology keeps processing and matching right on the device Standalone application as time attendance access control user identification Accurate and Fast Identification Industrial Leading Dual Sensor Facial Recognition Algorithm FAR lt 0 0001 1 Many up to 500 users less than 1 second Large user and log capacity User capacity from 500 users 5000 card users Over 150 000 logs and optional image capacity over 70 000 Reliable performance under different environments Different source light Technology The system can work in different light condition ev
16. egistration the procedure 1s the same to face registration in page 9 Ifchoose Card Card and photo or Card and Face mode in the previous step then the system will ask user to register User Manual Ver 2 6 23 Card Press ESC to return to the main menu Register User After choose one verify method User Privilege interface will be shown there are three options Attendance amp Access Attendance only or Access only Press OK to confirm and press ESC to ignore as alternative a a ES E The register successful information will be shown on the screen The following information will be shown User Number Name Permit Open Door Permit Attendance Card Registered as the following figure shown based on user s options and the correct hint voice can be heard after 2 seconds it will return to Input User No interface to register next user User Manual Ver 2 6 24 Register User Register Finished The register successful information will be shown on the screen After 2 seconds the system will return to previous interface automatically Modify User Modify User Model Modify User In User Management menu press the corresponding number 2 to enter the Modify User model directly User Manual Ver 2 6 25 Modify User 1 Name Input User Number In the Modify User model input corresponding User
17. en in the dark Over three years Chinese market testing Flexible I O interfaces Internet Protocol based enables LAN or Network deployment USB Host for User data upload or download via USB flash driver Wiegand input output makes system compatible with different access control panel User friendly design 3 5 inch color screen for face positioning Contactless authentication for the ultimate in hygienic voice User Manual Ver 2 6 prompts for guide Device Configuration Front View Figure User Manual Ver 2 6 5 Back View Figure 1 3 5 inch TFT Color LCD Display the function menu and user images information 2 Navigation Key Press 1 keys to select the function that you want to pafom User Manual Ver 2 6 6 3 4 5 6 7 8 9 in the menu Area for swiping RFID Card Swipe RFID card around this area Left sensor Capture the face images Right sensor Capture the face images LED Located around sensors provide enough light for sensors to capture face images OK Confirmation key If there is prompt information popup or options need to be confirmed press OK to confirm the operation ESC Return Cancel key Under the selection prompt or input states press ESC to cancel the operation When the system under the sub interface press ESC to exit the current interface and return to the previous interface Index Numeric key Index list key Under the menu s
18. f the recognizing process has taken over 5 seconds system will prompt user Please Try Again User Manual Ver 2 6 69 User No amp Face Recognition If some users cannot be detected well or for high security application press the backspace key lt lt to enter the input User No interface input the user number first and then perform face verification If the User Number input is not existed the prompt information will be shown and system will return to the input User No interface Card Recognition If user selects the card authentication method the user will be verified by card Once card verification success a click voice can be heard the device is taking a photo of this user and this face picture will be saved in the device for security photo Card amp Face Recognition If user selects the Card amp Face Recognition authentication method user can register the card first and register face to combine the authentication method User need swipe the card first there will be face verification after card verified User Manual Ver 2 6 Authentication Successfully If authentication successfully the system will utter the correct prompt voice In face attendance model system will save current recognition time automatically In face access controlling model the system will output the corresponding access controlling signal to control the access according to the
19. hen specifically time the device offers five bells Set Bell Alarm Time Bell Stat 1 05 00 belll Off The admin can set different sound from eight bell rings to divide User Manual Ver 2 6 52 different time point Set Work Status The System already has two statuses as default setting 1 on duty 2 off duty Choose Add Status to add new status The system totally can support 8 statuses The status also can be start automatically Related Parameter Status ID Range 1 255 Status Name 18 sheets per status View all status through pressing Browse Status The system have set on duty time for 9 00 and off duty time for 18 00 as default Press Status Switch Time to change corresponding status time User Manual Ver 2 6 53 Browse Status 1 On Duty Press key to select the corresponding status in the recognition and Standby interface Set Work Status E Work Stat Off Add Status Add Status User Manual Ver 2 6 54 Browse Status Modify Status Delete Status 1 On Duty Modify Status is to amend an existing status in the device and Delete User Manual Ver 2 6 55 Status 1s to remove a selected status Set Work Code 4PBro se Work Code 3 Add Work Code T M d i Work Code Dek teNork Code Press Add Work Code to set a new work code Firstly input an available work code ID press OK to confirm Then input a name for
20. ication failed after 3 cycles continuously Recognition Failed will be shown as the following figure the wrong voice prompt can be heard After 2 seconds it will return to User Manual Ver 2 6 18 the standby state Function Menu There are 7 options in the function menu Set Administrator User Management Record Management USB Management System Setting System Information and Auto Test Press keys to select the corresponding option and then press OK to operate this option or press the corresponding number to operate the corresponding function directly User Manual Ver 2 6 19 Administrator Function Menu User Management Enter to the function menu press the corresponding number 2 to enter User Management model directly In this model press ESC to quit and return to the Function Menu Register User Model In User management menu press the corresponding number 1 to enter to Register User model directly Register User Parameter Total Capacity Maximum number is 500 users User Number Range 1 99999999999999 14 bits Support Card ID IC card Face Image Model 18 sheets per person User Manual Ver 2 6 20 Y Caution User Number is formed by nature number and it cannot repeat 0 cannot be used in front of the job number for example 0020 it will be recognized as 20 Register User Input User Number In the Register User model there will be an editing frame
21. ion Restoration and restart When the system halted and cannot quit you can remove the adapter to restore and restart the system or you also can press RESET to restart the device Restore to default setting Restore all parameter to the default setting Non Water proof The device is non waterproof please keep away from water Prevent from Falling The parts in this device are friable please prevent the device from dropping smashing bending and high pressure Cleaning Please use soft cloth or the other similar material to clean the screen and faceplate please avoid cleaning with water and cleanser Low Temperature Environment The working temperature for screen and the main parts in this device are the normal indoor temperature The performance of this device will get worse if the working temperature extend this temperature range User Manual Ver 2 6 Please prevent the screen from oil or any sharp things Please use the equipped adapter for the device the other unknown adapters will burn out the device User Manual Ver 2 6
22. lected user User Manual Ver 2 6 28 Mpelete User User Deleted will be shown on the screen and the correct hint voice can be heard the system will return to the Delete User menu automatically Delete All Users The caution information will display on the screen to remind administrator Cannot Recover as the following figure shown Delete All Users D lete All Users Delete All Users Press ESC to cancel and the system will return to Delete User menu Press OK to start this function all users information will be 99 cleared and Deleting Waiting and rate of process will be displayed on the screen After that Finished will display and the correct hint voice can be heard after 2 seconds the system will User Manual Ver 2 6 29 return to Delete all Users menu automatically User Inquiry The user information can be searched by ID or Name Input ID or Name the information of user can be found Choose the user on screen modify and delete operation can be carry out Record Management In the function menu press the corresponding number 3 to enter User Manual Ver 2 6 30 to Record Management model directly In this model press ESC to quit and return to the Function Menu Record Inquiry In Record management menu press the corresponding number 1 to enter the Record Inquiry model and press ESC to quit and return to th
23. n it finished and utter the correct hint voice After 2 seconds system will return to the Function Menu Caution The imported file must be USER TXT or USERALL TXT which is exported from the device and the contents must not be modified unless there will be a default User Manual Ver 2 6 36 Import Users List Press number 6 to import the users number and name information that saved in USERLIST TXT file from the USB flash driver to the database in the device The imported data will add up or cover the former data according to the User Number The device will utter the correct hint voice when finishing import Import Work Code Press number 7 to import the work code number and name information that saved in WORKCODE TXT file from the USB flash driver to the database in the device The imported data will add into the device that will utter the correct hint voice when finishing import Import Work Status Press number 8 to import the work status number and name information that saved in STATUS TXT file from the USB flash driver to the database in the device The imported data will add into the device that will utter the correct hint voice when finishing import Firmware Upgrade User Manual Ver 2 6 Ipgrade by USB Disk pgrade by USB Disk When the USB memory is inserted to device the device will check up the firmware in USB memory If the right file has been confirmed the upgrading will
24. onds the system will return to previous interface automatically Modify or Delete Administrator Enter the Set Administrator menu Register Again Admin Verifying Select the corresponding administrator to modify User Manual Ver 2 6 16 Select Register Again in the menu Enroll face template again Modify and Delete Administrator Wunetion Menu Set Admin Eb Set Admin 4 ra T C T30kK Cancel Select the corresponding administrator to delete or modify Select Modify or Delete Administrator Press OK to confirm Finished will be shown on the screen after 2 seconds the system will return to Set Administrator menu Delete Admin LU Finished CTSDelete E FER E Cancel diss If only one administrator remained it will be forbidden to delete as the following figure shown and the wrong voice can be heard After 2 seconds the system will return to Set Administrator menu User Manual Ver 2 6 17 E Set Admin Administrator Verification Press MENU to enter to administrator verifying model ID and Pin ID and Face or Card and Face will be required Admin Verifying Admin Verifying After face verification successful administrator could enter the menu to do more settings as register user set system User will be verified during 5 seconds as a cycle for administrator verifying If verif
25. rt administrator verifying function automatically after the verification the USB flash driver function menu as following figure shown Remove the USB flash driver or presses ESC the system will return to the standby interface Y Caution Due to the capability of chip is limited a few models of USB flash drive could not be compatible with this device User Manual Ver 2 6 USB flash driver operation Export records Press number 1 to export all attendance records and access records from the device the procedure percent will be shown on the screen the data exported will form a new file named TIME TXT in the USB flash driver Management Export Records After that there will be successful prompt information display and utter the correct hint voice After 2 seconds system will return to the Function Menu User Manual Ver 2 6 34 Export Part Users Press number 2 to export the selected user s information and face images files input his User Number and press OK to confirm and then input the next one s User Number Press ESC to finish the selection the system will export the information and face images files you had selected before During the exporting process the procedure percent will be shown on the screen There will be successful prompt information display when 1t finished and utter the correct hint voice After 2 seconds the system will return to the Function Menu The d
26. s controlling engineer to set the format of the access controller port in the device it can support the following setting Wiegand 26 or 26 with site code and Wiegand 34 or 34 with site code as the following figure shown Also it can be User Manual Ver 2 6 48 customized by clients Wiegand Output Wiegand output can be customized for different requirements Wiegand Output The wiegand output can be set various User ID or Card Number User Manual Ver 2 6 AQ Press OK to confirm the setting the information of access controlling signal will be shown on the screen it will return to the Set System menu after 2 seconds presses ESC to quit modification and return to the Set System menu ds When under setting system press OK to confirm settings then do more settings if press ESC the setting will not be saved and the system will return to the Set System menu 6 Set Attendance User Manual Ver 2 6 50 Set Attendance iterval Set Interval Set time range or attendance interval The system will record attendance based on Interval Time Interval is 2 means the system will only record the first attendance log and other logs not within 2 minutes for each user Notice Interval Time Range 0 255 Value 0 means set interval function is not being used et Interval Set Bell Alarm User Manual Ver 2 6 5 Sel at Sound In order to give the user a tip w
27. setting of access control The User Number Name current recognizing time will be shown on the screen Access amp Attendance will be shown according to the user register setting ECC After 1 second the system will return to the standby interface or face recognition interface to wait for recognizing the next user Hint If selected Open Work Code model you will have to select corresponding work code after recognizing User Manual Ver 2 6 71 successfully the work code also will be shown on the screen User Manual Ver 2 6 Appendix Technology Specification User Capacity 500 Users Card Capacity 5000 Cards Record Capacity 150 000 Access Control Records Image Capacity 70 000 Images Security Image Capacity 4GB SD Card inside Recognition Algorithm Dual Sensor V3 0 Lens Specialized double lens Verification Method Face Recognition Pin amp Face Recognition Card amp Face Recognition Card Recognition Card amp Photo Recognition Card Recognition ID IC card Verification Speed Less than 1 Second 500 Users Keyboard 5 4 Touch Keyboard LCD 3 5 inch TFT Color Screen 65 000 Bright Color 320 240 Resolution Communication Method Standard TCP IP USB Flash Drive Security Alarm Removing Alarm Output for Access Control System Standard Wiegand Output Relay Output Power 12V DC Working Current 1A Working Distance 30 80cm Working Temperature 0 C 40 C Working Humidity
28. splayed at the right side Face Register Face image collecting interface will be shown on the screen after selecting an unset administrator The Administrator ID and Administrator Name will be required A Set Admin Set Admin There are three method to verify ID and Pin ID and Face or Card and Face ID and Pin will need the administrator input the ID and password User Manual Ver 2 6 l4 Set Admin During the face enrollment white frame means the face position is not good green frame means user s face position is good for enrollment Card and Face require user swipes card and then register the user s face A Set Admin As soon as the face is detected by sensors the green line frame will be shown on the screen the system will mark user s face outline character and process user s face information with digital automatically The processing bar will be shown at the bottom of screen to display the process of the enrollment The prompt information will also be displayed to remind user to watch sensors lower your head raise your head and turn head to left turn head to right User Manual Ver 2 6 15 dis the system increases accurate rate of recognition to avoid the same administrator registers themselves again on another administrator ID Register Finished E Set Admin The register successful information will be shown on the screen After 2 sec
29. tate each number corresponding to each option in the menu press any number key to select and operate the corresponding function in the menu Numeric key Under the input state press the Numeric key 0 9 to input numbers or letters 10 Power key User Manual Ver 2 6 To turn on or turn off the device 11 Function key F1 F2 F3 3 function keys to provide a quick switch method for work status Press F1 to call work status list Press F2 to switch work status to On Duty Press F3 to switch work status to Off Duty 12 Backspace key Under the input state press this key to delete a number the cursor will go back a space 13 MENU key Press MENU key to shift to the Administrator Verifying interface user can operate the system as an administrator after verified by the system 14 Reset button The device will be restarted by pressing the key in this hole 15 USB port Connect with USB flash driver after verified by an administrator user can import or export data by using the USB flash driver 16 Speaker Broadcast system voice or information 17 Terminal blocks Terminal blocks support several communication ports and DC power port 18 Device installation mounting plate It 1s used for fixing the device on the wall User Manual Ver 2 6 19 Removal alarm trigger A trigger to control status of the removal alarm 20 Power adapter port Power adapter port 12V 1A DC adapter standard 21 Network cabl
30. ty of user record and pictures Display format Current Quantity Total Capacity Capacity Info Product Information Display the IP address Mask Gateway MAC SN Version and Resource Number press ESC to quit and return to the System Information menu User Manual Ver 2 6 63 dius When a user registered successfully the user quantity in capacity information will add one at the same time the photo quantity will also add one Auto Test TA Auto Test Auto Check User Manual Ver 2 6 64 System Setting Model In the function menu press the corresponding number 7 to enter Auto Test model directly Press ESC to quit and return to the Function Menu interface Auto Check Do the whole system test automatically User should follow the instructions which show on the device screen Check Program Test device embedded program and return the testing result Check LCD Test device LCD screen Press OK to confirm pass the test Press ESC to confirm fail the test User Manual Ver 2 6 65 Check Keyboard Test device keyboard Following the instructions showed on device screen Check Keyboard Check Speaker Test device speaker Press OK to confirm pass the test Press ESC to confirm fail the test User Manual Ver 2 6 66 Check Camera Test device cameras Press OK to confirm pass the test Press ESC to confirm fail the test Weheck Camera
Download Pdf Manuals
Related Search