The user manual for BX-5Q1/5Q2 cascade function Date
Contents
1. lt 9 Pb ad Pa Shanghai Onbon software technology Co Ltd The user manual for cascade function of BX 5Q1 5Q2 1 Connection drawing 7 7 Width cascade in Display screen Sub controller Gully corteniher Sub controller Nain controller Computer Router or switchboard 1 2 Height cascade 1 www onbonbx com onbon onbonbx com hab re Shanghai Onbon software technology Co Ltd Sub controller Router or Switchboard SCE GER h Sub controller sub controller HI oub controller Computer 2 Preparation before set cascade parameters 2 1 Prepare a set of switchboard or router the interfaces should be enough for computer and controllers 2 2 Distribute the IP adaress subnet mask and gateway 2 3 Confirm the scan mode which already has in the software or you need to get the right scan mode by smart scan configuration 3 Software setting 3 1 Open LedshowTW 2073 click setuo choose set parameter enter passwords 888 5 2 www onbonbx com onbon onbonbx com re Pe Shanghai Onbon software technology Co Ltd By LedshowlT 2013 File Edit fAutoFit Setup Common commands Advanced Configuration Language Help Set Screen Parameters teuje orl Reset Screen Farameters Ce ee eee E Displa arameter confi ation cw E E aan E ee E F Firmware Maintenance EEE H Er 1 Hetwork server configuration 1 Timing 1 GPRS server configur2. of the LAN controller is set to the current IP address TAE HRH 4 38 Then promt the the configuration for sub controller 2 and the last step send setup screen IP command successed Means the sub controller 1 get configuration successed and next connect the second sub controller Then click next 4 4 Check and click ok 4 5 Then the main controler configuration and also prompt that sending setup screen IP command successed Click next 4 6 Check and click ok 6 www onbonbx com onbon onbonbx com Shanghai Onbon software technology Co Ltd gt 4 7 Prompt the main controler and sub controllers P cascade configuration successed and connect the sub controllers which get bk configured to router or swichboard click ok 4 8 Write parameters By Parameters Setting Screen list Screen parameters Scan Configuration wiring Diagram Build Address ee Communication Mode Storage Volume Bx 501 Network commur AZEMBytes Screen Mame LEE Controller BE 50 Full colc Screen width Screen height 512 64 gt W Cascade mode Module width Module height 16 16 Cascade mode B 5Q series maximum support 4096 64 pixels Network communication configuration Connection Mode f Fixed IP mode jis2 t68 0 2 o Oo SY Change the IP address of the controller subnet mask gateway pork and IP information click on the controlle
3. ation Controller IP configuration MAC Address Maintenance Check the screen state By Pass ord Please Enter the Password canes _ 3 2 Select controller and controller model like BX 5Q2 choose cascade mode enter the corresponding data in screen width screen height module width module height then click controller cascade configuration 3 www onbonbx com onbon onbonbx com lt a lad a ee Shanghai Onbon software technology Co Ltd 1 al Screen parameters Scan Configuration Wiring Diagram Main Performance Bx 501 Screen Mame Build Address 1 Maximum pixels o T_T 40K dots 40960 3 l i 2 Display Mode Controller Communication Mode Storage Volume 1024 40 512 80 320 128 256 160 128MByt Bx S9 Full colc BE Sol Network commur yhes Behe ae eae 100M Network US 4 Sensors Temperature Humidity Noise Screen width Screen height S Timer support Bz 2 z 64 i Cascade made 6 Support Full screen best Module width Module height 16 gt 16 Controller cascade configuration Cascade mode B 59 series maximum support 4096 64 pixels Network communication configuration Connection Mode es f Fixed IP made CE Change the IF address of the controller subnet mask gateway port and IF information click on the controller IF configuration gt carry on IP information set Quickly scan config
4. r IP configuration gt carry on IP information set the screen otherwise the display will appear abnormal it is recommended to set the l The current set of screen parameters must be consistent with the actual parameters of screen parameters prior to configure the scanning parameters W Show advanced configuration Functions Establishing the communication of the controller Main Performance Bx 501 1 Maxirnum pixels 40K dots 40960 2 Display Mode 1024 40 512 80 320 126 256 160 3 Communication interface 100M Network Lse 4 Sensors Temperature Humidity Moise S Timer support 6 Support full screen test Quickly scan configuration Paipeir Set Scan Here only For popular configuration of three LED units For quickly scan Parameters Read back Write parameters Close The 888 permission mode the computer allowed to connect a screen orompt write oarameters successed Then you could edit and send program s 7 www onbonbx com onbon onbonbx com
5. t cascade mod Slave controller 1 Controller IP address Slave controller 2 Master controller IPF 192 165 0 4 IPF 1924 165 0 2 192 168 0 3 width 160 width 192 Height 64 Height 64 Widkh figo Height A Each controller lt IP Cascade configuration gt the access must be in accordance with the position shown 4ssigned to each controller with load width should be as close to equal 4 Write the cascade list and IP address to the controller 4 1 Connect a controler with the router or switchboard which your computer is using click next The configuration window for sub controller 7 note you could modity the subnet mask and defaulted gateway there 5 www onbonbx com onbon onbonbx com wo eld a Pe Shanghai Onbon software technology Co Ltd By Step 2 lt Slave controller I gt Controller IPC Pa Be sure to use this Feature the connection only with lt Slave controller 1 gt Otherwise it will put all of the LAN controller is set to the current IP address Connection Mode f Fixed IP mode Screen IP Information Server IP Information IF address 192 16803 192 166 184 Subnet mask 255 255 255 0 Gateway 192 168 0 1 Port 5005 2 Screen heartbeat information l Previous step Click next bk 4 2 check the prompt and click ok Prompt A Be sure to use this feature the connection only with Slave controller 1 gt Otherwise it will put all
6. uration Pisye seeds iziyeal Set Scan Here only For popular configuration of three LED units For quickly scan the screen otherwise the display will appear abnormal it is recommended to set the f The current set of screen parameters must be consistent with the actual parameters of screen parameters prior to configure the scanning parameters W Show advanced configuration Functions Parameters Read back Write parameters Mot Find the screen The 888 permission mode the computer allowed to connect a screen 38 3 Cascade configuration 3 3 1 Add cascade number after you enter the number the software will distribute the screen height and width automatically 4 3 3 2 Choose cascade mode enter the corresponding IP address sub controller main controller Example There are three controllers tor cascade then there will be two sub controllers and one main controllers The prepared IP 192 168 88 17571 192 168 88 7152 192 168 88 158 click sub controler 1 enter the IP address 192 168 88 1757 click sub controler 2 enter the IP address 192 168 888 152 click main controler enter the IP address 192 168 88 158 then click next 4 www onbonbx com onbon onbonbx com Slane Shanghai Onbon software technology Co Ltd By Step I lt 1 ffae Controller cascade configuration Cascade number Cascade mode Screen width Screen height 3 fe Width cascade mode Heigh
Download Pdf Manuals
Related Search