(Discontinued) Single Wire Version Manual
Contents
1. e With the battery co DEL and then pi button e While still pressing OPEN CLOSE cover located on th BD1 XL Biometric DeadBolt Lock http www advancedactuators com A single long beep will be heard Sensor will flicker for less than one second Short beep will be heard and sensor will power on Rest an Administrator s fingerprint on the scanning window When the Administrator s fingerprint is successfully verified two long beeps will be heard indicating that ALL enrolled fingerprint users have been deleted o If you hear four beeps this indicates that the verification of the Administrator s fingerprint was not successful Begin again from the first step of Section IV 37 http www advancedactuators com e Close the sliding cover IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE BD1 WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY CLOSING THE SLIDING COVER Section V Unlocking the BD1 from outside In case of emergency override keys can be used to disengage the deadbolt Please use the following steps to unlock the BD1 from outside with your enrolled fingerprint BD1 XL Biometric DeadBolt Lock 38 http www advancedactuators com e Fully lift the sliding cover located on the outdoor unit BD1 XL Biometric DeadBolt Lock 39 http www advancedactuators com e A single short beep will be heard and the fingerprint sensor will power on e After the2. Moist fingers give better images than dry ones If on cold dry days you have difficulty for example try moistening your finger with your breath or a little lotion Very dry dirty or scarred fingers are obviously not recommended since they will obscure the fingerprint The pointer finger is by far the best fingerprint to enroll The thumb is the second best digit If the pointer finger is difficult to enroll or verify try enrolling the same NON ADMIN fingerprint 2 or 3 times at slightly different angles EX Enroll same pointer finger as users 3 4 and 5 BD1 XL Biometric DeadBolt Lock 24 http www advancedactuators com Always wait until the fingerprint scanner turns on to place your finger on the scanning window This is true for both fingerprint enrollment AND verification When trying to enroll or verify fingerprints in direct sunlight be sure to shade the sensor with your shadow so sunlight will not reflect off of the mirror in the sensor gt E N Put the finger center on the iN center of the scanner window Place finger flat on the Gi od Had Rad 1 window Good Bad _ Don t put finger on the edge and then move to the center Raise the finger then leave N scanning window after t ia 4 fingerprint scanning Don t drag the finger on the surface of the scanning window Important Programming Notes When Adding or Deleting Fingerprints the closed sliding cover must be fully l
3. BD1 XL Biometric DeadBolt Lock 18 http www advancedactuators com 11 Insert 4 high quality AA batteries BD1 XL Biometric DeadBolt Lock 19 http www advancedactuators com d 12 Press the electronic open close button to ensure that the deadbolt opens and closes electronically 4 6 Final inspection adjustment prior to enrollment Note After installation and prior to using the unit make sure you read and follow the steps below 1 Turn the inside knob to the horizontal position next turn it to the vertical position locked position It should turn freely If and when the inside and outside locks are attached securely and the inside knob doesn t turn freely see the trouble shooting table below for possible solution If the knob turns freely continue with the next step 2 Try to lock and unlock from outside by fully opening and closing the sliding cover 8 Try to lock and unlock from inside by pressing the Open Close button to ensure it works well electronically IMPORTANT SECURITY NOTE WITHOUT ANY FINGERPRINTS ENROLLED THE BD1 WILL LOCK AND UNLOCK BY FULLY OPENING AND FULLY CLOSING THE SLIDING COVER BD1 XL Biometric DeadBolt Lock 20 http www advancedactuators com 5 Trouble Shooting PROBLEMS POSSIBLE REASONS SOLUTIONS Indoor turn knob does not turn or turns very sluggishly Indoor turn knob turns but nothing happens 1 Incorrect installation Incorrect tailpiece length Th
4. us at support advancedactuators com for additional support or by phone at 800 408 7101 USER ENROLLMENT TABLE BD1 XL Biometric DeadBolt Lock 42 http www advancedactuators com BD1 XL Biometric DeadBolt Lock 43 http www advancedactuators com BD1 XL Biometric DeadBolt Lock 44
5. Strike Lining Box on the door jamb A 1 Close the door until the deadbolt touches the door jamb along the face plate to mark the horizontal center lines 2 Measure one half of the door thickness from one side of the door jamb and then mark the vertical center lines 3 Extend the vertical center line and the horizontal line to mark the drill center point for the strike Bore a 1 diameter and 1 deep hole in the door jamb at the center point for strike To ensure the proper deadbolt function this hole must be drilled at least 1 deep Chisel the door jamb at 1 16 deep for the strike plate which must fit flush with the door jamb Insert the strike lining box and then fasten screws to the plate BD1 XL Biometric DeadBolt Lock 10 http www advancedactuators com 4 3 Sizing Tail Piece to the right length The BD1 is designed to fit door thicknesses of 1 3 8 to 2 Four pre sized tailpieces are included with the BD1 for 1 3 8 1 5 1 32 and 2 thick doors Your door thickness and length of the tailpiece being used must match exactly EX If your door is 1 34 thick then you must use the 1 long tailpiece The BD1 comes with the 1 4 tailpiece pre installed If your door is not 1 4 thick but the thickness matches one of the other pre cut tailpieces included with the lock then you must swap out the tailpiece For video directions on how to swap the tail
6. ack plate of the Indoor Unit If the door is left handed please push the orientation selector switch to L position if it s right handed switch the selector to R position BD1 XL Biometric DeadBolt Lock 14 http www advancedactuators com 2 Left handed doors are defined as dE e hinge on the left when you are Dan entering the home from outside The ite is true for right handed i _ a rue for rig ande Right Hand Door Left Hand Door Right Handed Left Handed 3 Plug wire set into circuit board making sure all prongs are firmly seated BD1 XL Biometric DeadBolt Lock 15 http www advancedactuators com 4 Press sheathing of wire casing into the wire holder clamp 5 Turn the manual turn knob to the vertical position facing downward BD1 XL Biometric DeadBolt Lock 16 http www advancedactuators com 6 Insert the tail piece into the vertical retaining slot of the indoor unit 7 Gently finish joining the outdoor and indoor units together ensuring all fixing posts are aligned properly 8 Fasten the two shorter screws through the upper fixing post holes on the upper section of the inside unit BD1 XL Biometric DeadBolt Lock 17 http www advancedactuators com 9 Fasten the two long screws through the bottom fixing post holes on the inside unit 10 Move the manual turn knob back and forth to ensure that deadbolt opens and closes mechanically
7. e installation template when installing the BD1 on a door with an existing deadbolt 3 Cut out the two 3 8 holes on the Installation Template that correspond to your existing backset 2 3 8 or 2 Ya BD1 XL Biometric DeadBolt Lock 5 http www advancedactuators com 4 Rest the installation template on the front of the door on top of the existing 2 1 8 hole making sure that it is aligned properly for the door s existing 2 3 8 or 2 4 backset 5 Mark the two 3 8 holes that you cut out of the installation template on the door with a magic marker 6 Bore the two 3 8 holes into the door using a 3 8 drill bit making sure that the holes fully penetrate through the door 7 Go to Section 4 3 in the User Manual For doors that do not have a cylindrical deadbolt lock or a hole for the cylindrical deadbolt lock A Start approximately 46 from floor Select the appropriate installation template according to the length of the backset Fold and apply the template to the edge of the BD1 XL Biometric DeadBolt Lock 6 http www advancedactuators com 3 12 Bore holes BD1 XL Biometric DeadBolt Lock 7 door bevel Mark the center point of the cylinder hole on the door face and then mark the center point of the deadbolt hole on door edge as indicated on the template For installation of combination set door handle and deadbolt it is recommended that the dis
8. e tail piece did not go through the cross slot of the deadbolt Tail piece was trimmed too short and does not penetrate the slot of the indoor unit BD1 XL Biometric DeadBolt Lock 21 1 Make sure the tail piece was inserted vertically through the cross slot of the deadbolt and slot of the indoor unit while the turn knob was vertical facing down Measure the door thickness and swap or trim the tail piece per section 4 3 of the installation manual Remove and reinstall the outdoor unit Then insert the tail piece through the cross slot of the deadbolt and slot of the indoor unit while the turn knob is in vertical position facing down Contact the BD1 dealer that you purchased to lock from OR Contact us at info bioaxxis com The sliding cover is fully lifted to power on without any fingerprint enrolled inside the deadbolt does not disengage or four alert beeps are heard When the sliding cover is fully lifted and immediately put down to engage the deadbolt but the deadbolt does not fully engage or four alert beeps are heard When the sliding cover is lifted up during daily use nothing happens fingerprint scanner does not blink Six beeps are heard when any function is performed http www advancedactuators com 1 Right amp left hand door configurations is set incorrectly The tail piece was not set properly Improper positioning of the strike and strike lining b
9. fingerprint sensor powers on rest any enrolled fingerprint on the sensor window to verify If fingerprint verification is successful the deadbolt will disengage and a single short beep will be heard If verification of enrolled fingerprint was not successful then 4 short beeps will be heard If this happens the fingerprint scanner will still turn on two additional times enabling users to try more If all the two additional verification attempts still fail please start the unlocking process over again from the beginning of this section e Close the sliding cover Section VI Locking the BD1 from Outside In case of emergency override keys can be used to engage the deadbolt BD1 XL Biometric DeadBolt Lock 40 http www advancedactuators com Please use the following steps to lock the BD1 from outside when leaving e Make sure your door is closed e Open and immediately close the sliding cover e Deadbolt will engage and a single short beep will be heard Section VII Locking and Unlocking the BD1 from Inside In case of emergency manual turn knob can be used to disengage the deadbolt Please use the following steps to lock and unlock the BD1 from inside BD1 XL Biometric DeadBolt Lock 41 http www advancedactuators com e Press the OPEN CLOSE button located between the ADD and DEL buttons e Deadbolt will engage disengage and single short beep will be heard Support Contact
10. http www advancedactuators com PREFACE gt Thank you for purchasing the BD 1 fingerprint deadbolt gt Please read the documentation carefully before installation amp use The manual details all installation procedures and operation steps gt Manufacturer and or Distributors of the BD1 will not be responsible for any damages caused by incorrect installation or mishandling of the lock Any such damages will void manufacturer s warranty Table of Contents BD1 XL Biometric DeadBolt Lock 1 http www advancedactuators com rS e onm E E E E E E EEE l Installation Manual WIS EE NEA PET A E EEE tance ES E EE 2 2 Reged LOON sn neten nere eelde 4 3 Proensal omise E ea en waevandaddekaande 4 3 1 Mark and bore holes on the door 4 52 Deadbolt Latch SelecHonusesisna a 8 A ASA ON nc eenden nlet eet 9 4 1 Installation of Deadbolt nnen 9 4 2 Installing Strike and Strike Lining Box on the door DEEL ORE 10 4 3 Sizing Tail Piece to the right length 11 4 4 Installation of the Outdoor Unit 12 4 5 Installation of the Indoor Unit ee eeeeeeeeee 14 J rouble SMOOMNG sictarecerisisataicnetetieh sta recSateb ieee estes inaecuees 21 Operation Manual i iccccsevascataxaiiond aiia a a 23 Section I Enrolling Administrators First 2 Fingerprint USERS ensen edele eten 26 Section II Enrolling Fingerprint Users 3 thru 30 30 Section II Deleting Individual Fingerpri
11. icates that programming operation was successful Short Double Beep Indicates that individual fingerprint user deletion sequence has begun Long Double Beep Indicates that Delete All programming was successful Four Beeps Indicates unsuccessful enrollment unsuccessful verification attempt OR BDI was improperly installed see Installation Guide Six Short Beeps Low battery alert change batteries Common definitions of terms used when using the BD1 BD1 XL Biometric DeadBolt Lock 23 http www advancedactuators com Fingerprint Enrollment Process of adding fingerprints to the BDI Enrolled Fingerprints Fingerprints that have been successfully added into the BDI Verifying Fingerprints Process of authentication by scanning enrolled fingerprints to A Unlock the door B Authenticate Administrators enrolled fingerprints to program the BDI Before enrolling and verifying fingerprints make sure to read the following helpful hints for Fingerprint Enrollment and Verification Generally the center of the vortex swirl of the fingerprint pattern is the key data point ideally it is placed in the center of the small glass window in a consistent way Your finger should be flat motionless and held with light pressure in the same way each time See the picture below for some guiding drawings Light pressure when placing the finger on the scanner gives the best image but the finger must not move during scanning
12. ifted within 8 seconds after pressing the ADD or DEL button or the BD1 will power off If this occurs simply close the sliding cover press the ADD or DEL button again and fully lift the sliding cover immediately to restart the programming sequence BD1 XL Biometric DeadBolt Lock 25 http www advancedactuators com The first two fingerprint users enrolled will automatically be programmed as ADMINISTRATORS Users 1 and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door The 3rd thru 30th fingerprint users enrolled Users 3 thru 30 are automatically programmed at the USER level USER level fingerprints can only be used to unlock the door not to program the lock Section I Enrolling Administrators First 2 Fingerprint Users Sliding cover must be closed before any programming sequence can begin As noted in the Helpful Hints section the first two users that enroll their fingerprints into the BD1 will automatically be programmed as ADMINISTRATORS Users 1 and 2 ADMINISTRATORS can apply all programming functions as well as verify their fingerprints to unlock the door Please use the following steps to enroll the first fingerprint user ADMINISTRATORI USER 1 http www advancedactuators com e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard BD1 XL Biometric DeadBoli F
13. n the scanning window thru all three scans After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning http www advancedactuators com e Close the sliding cover Section II Enrolling Fingerprint Users 3 thru 30 Sliding cover must be closed before any programming sequence can begin BD1 XL Biometric DeadBolt Lock 30 http www advancedactuators com As noted in the Helpful Hints section the third thru thirtieth fingerprint users enrolled Users 3 thru 30 are automatically programmed at the USER level USER level fingerprints can only be used to unlock the door not to program the lock Please use the following steps to enroll additional fingerprint users Users 3 thru 30 e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard BD1 XL Biometric DeadBolt Lock 31 http www advancedactuators com e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A single short beep will be heard and the fingerprint sensor will power on e After the fingerprint sensor powers on restan ADMINISTRATOR S finger on the sensor window to verify
14. nt Users 33 Section IV Deleting ALL Fingerprint Users 36 Section V Unlocking the BD1 from outside 38 Section VI Locking the BD1 from Outside 40 Section VII Locking and Unlocking the BD1 from USES En eben deet eene 41 USER ENROLLMENT TABLE nnee 42 1 Parts Please familiarize yourself with all the parts in the packaging box of the BD1 If any part is missing or damaged contact our service center or your local dealer BD1 XL Biometric DeadBolt Lock 2 http www advancedactuators com Outdoor Unit Indoor Unit Strike Lining Box Outdoor Rubber Gasket D eadbolt Latch Deadbolt Latch 2 3 4 backset 70mm 2 3 8 backset 60mm Screws asn 2x40 mm amp 1 x 29mm Wooden amp Metal Alkaline Screws Batteries BD1 XL Biometric DeadBolt Lock 3 http www advancedactuators com 2 Required Tools 1 Electric or battery operated Drill One 3 8 Diameter Drill Bit 3 One 1 Diameter Drill bit 4 One 2 1 8 Diameter Drill Bit A pair of scissors Vise Grip 9 Philips amp flat head screw drivers Metal Cutters or Hacksaw 3 Pre installation 3 1 Mark and bore holes on the door 3 11 Mark holes on door For doors with existing deadbolt lock with 2 I 8 diameter hole BD1 XL Biometric DeadBolt Lock 4 http www advancedactuators com 1 Remove existing cylindrical deadbolt 2 Please be sure to use th
15. ocated on the indoor unit e Short Double Beep will be heard BD1 XL Biometric DeadBolt Lock 34 http www advancedactuators com e Fully open the sliding cover located on the outdoor unit immediately e Sensor will flicker for less than one second e A single short beep will be heard and the fingerprint sensor will power on e Rest an Administrator s fingerprint on the scanning window e When the Administrator s fingerprint is successfully verified a single long beep will be heard indicating that the most recently enrolled fingerprint user has been deleted o If you hear four beeps this indicates that the verification of the Administrator s fingerprint was not successful Begin again from the first step of Section III BD1 XL Biometric DeadBolt Lock 35 http www advancedactuators com e Close the sliding cover e Repeat steps from the beginning of Section III to delete the next most recently enrolled fingerprint user Section IV Deleting ALL Fingerprint Users Sliding cover must be closed before any programming sequence can begin Deleting ALL enrolled fingerprint users will reset the lock and all users including Administrators fingerprints will be deleted With no fingerprints enrolled in the BD1 the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed Please use the following steps to delete ALL fingerprint users BD1 XL Biometric DeadBolt Lock 36
16. ox It may be deflecting the deadbolt Batteries not inserted correctly Wires not connected properly Low Voltage BD1 XL Biometric DeadBolt Lock 22 Correctly configure the unit for left or right hand door swing per section 4 5 Uninstall the outdoor unit and keep the UP sign side of the tail piece up and insert the tail vertically through the cross slot of the deadbolt while the turn knob is in vertical position Check the position of the strike and the strike lining box Remove amp reinsert the batteries following and signs in the battery house Check the connections and make sure wires are fully plugged in Change the batteries http www advancedactuators com Operation Manual Operation Manual Helpful Hints Please read before attempting to program the BD1 Please be sure to physically leave your door open until you have successfully enrolled the first user ADMINISTRATOR into the BD1 and have successfully verified the new user s fingerprint to unlock the door With no fingerprints enrolled in the BD1 the deadbolt will engage disengage when the sliding cover is fully opened and immediately closed Definitions of Indication Beeps Single Short Beep Indicates that any operations sequence has begun OR that the door has been successfully locked or unlocked OR that the sliding cover has been left open for more than ten seconds Single Long Beep Ind
17. piece go to the BDI product page at www BioAxxis com and click on the Support Material section on the bottom of the page for links to the instructional videos IF YOUR DOOR THICKNESS DOES NOT EXACTLY MATCH ANY OF THE PRE CUT TAILPIECES LENGTHS BD1 XL Biometric DeadBolt Lock 11 http www advancedactuators com THEN YOU MUST TRIM THE PRE INSTALLED TAIL PIECE TO MATCH YOUR EXACT DOOR THICKNESS If you need to trim the tailpiece be sure to measure the exact thickness of your door mark the tailpiece with a marker where it needs to be cut and trim the tail piece accordingly per the exact thickness of your door with a hacksaw or metal cutters Notes The motor could be dislodged if the tailpiece is not cut properly and is too long due to excessive pressure Warranty will be voided if this occurs 4 4 Installation of the Outdoor Unit 1 Attach the rubber gasket to the back of the outdoor unit BD1 XL Biometric DeadBolt Lock 12 http www advancedactuators com 2 Make sure the tail piece is vertical 3 Make sure the deadbolt is engaged 4 Insert tail piece through the cross slot of the latch 5 Insert the connector and wire through the cylinder hole below the deadbolt latch BD1 XL Biometric DeadBolt Lock 13 http www advancedactuators com 6 Insert the two upper fixing posts through the small upper holes on the door the newly drilled holes 1 Select the proper door opening orientation on the b
18. tance is 5 4 between the two center points Mark the center points of the two small holes on the door face for the two upper fixing posts mounted on the top plate of the outdoor unit as indicated on the installation template http www advancedactuators com A Bore a 2 1 8 diameter hole in the center of door face for chassis It 1s recommended to bore this hole from both sides of the door to avoid splintering Bore a 1 diameter hole in the center of door edge for deadbolt Bore two separate 3 8 diameter holes for the upper fixing posts 3 2 Deadbolt Latch Selection There are two deadbolt latches in each box one with a 2 3 8 60mm backset and the other with a 2 4 70mm backset Make sure which length you will need and select the right one before installation BD1 XL Biometric DeadBolt Lock 8 http www advancedactuators com 4 Installation 4 1 Installation of Deadbolt Insert the deadbolt latch into the hole in the edge of the door follow the UP sign keeping it parallel to the face of the door Mark the outline of the face plate and remove the deadbolt Then chisel 1 8 deep rectangular shape per your marking or until the faceplate is flush with the door edge Insert the deadbolt latch make sure the deadbolt UP sign is facing upwards Then fasten the screws BD1 XL Biometric DeadBolt Lock 9 http www advancedactuators com 4 2 Installing Strike and
19. that they are an Administrator e When the first Administrator s fingerprint is successfully verified the sensor will briefly turn off for less than one second e Immediately remove the ADMINSTRATOR S finger BD1 XL Biometric DeadBolt Lock 32 http www advancedactuators com e A single short beep will be heard and the fingerprint sensor will power on e Rest the new user s pointer finger on the sensor window during the first of three scans e Keep your pointer finger on the scanning window thru all three scans e After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start tha anrallmant anvanaaa var Close the sliding cover e Repeat steps from the beginning of Section II to enroll additional fingerprint users Section III Deleting Individual Fingerprint Users Sliding cover must be closed before any programming sequence can begin BD1 XL Biometric DeadBolt Lock 33 http www advancedactuators com The Individual Fingerprint User Deletion programming function deletes fingerprint users from the most recent fingerprint user enrolled to the earliest fingerprint user enrolled Please use the following steps to delete individual fingerprint users e With the battery cover removed press the DEL button l
20. ully open the sliding cover located on the outdoor unit immediately Sensor will flicker for less than one second A single short beep will be heard and the fingerprint sensor will power on After the fingerprint sensor powers on rest your pointer finger on the sensor window during the first of three scans Keep your pointer finger on the scanning window thru all three scans After the scanning is completed you will hear one of the following o Single long beep indicating that the operation was successful OR o Four beeps indicating that your fingerprint was not successfully enrolled If you hear four beeps please start the enrollment process over from the beginning http www advancedactuators com e Close the sliding cover Please use the following steps to enroll the second fingerprint user ADMINISTRATOR2 USER 2 e Remove the battery cover from the indoor unit e Press the ADD button located on the indoor unit e Single beep will be heard 28 http www advancedactuators com BD1 XL Biometric DeadBolt L Fully open the sliding cover located on the outdoor unit immediately Sensor will flicker for less than one second A single short beep will be heard and the fingerprint sensor will power on A single short beep will be heard and the fingerprint sensor will power on Rest the new 2 ADMINISTRATOR S pointer finger on the sensor window during the first of three scans Keep your pointer finger o
Download Pdf Manuals
Related Search