AX3 User Manual
Contents
1. User Manual All In One Terminal AX3 Contents Welcome Package COMORES aai 4 Getting to know 5 ETON ENTEN ea cream a naaa nnna un D RO VO a OTY 6 Optional I O interface 7 Specification 8 Installation Guide 9 Take our the system unit 9 Install the Power Adapter 10 Install a LCM Customer Display re rrr nerne nerne 11 Install a Second Display cccecseeeseseeeseeeeeeseeseeneenetaees 12 2nd VGA Power Setting ss 13 Install the MSR Fingerprint iButton Module 14 Version Change History 16 P2 16 Notices The information contained in this document is subject to change without notice We make no warranty of any kind with regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Proprietary information contained in this document is copyright protected Changes in this document or in the products described herein may be made without prior notice TRADEMARK Intel Cedarview are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation Other trademarks mentioned herein are the property of their respective owners P3 16 Welcome The following illustration displays the2. DEL gt key when the system is booting up to enter the BIOS Setup utility Select the Advanced tab Select VGA COM Power and LCD Brightness Configuration Ports and press lt Enter gt to go to display the available options A Powel 4 To switch on the power select 12V press lt Enter gt Please save the change by pressing F10 a aes P13 16 Install the MSR Fingerprint iButton Module MSR Fingerprint iButton module can be installed to either side of the system Choose one side and follow the steps below Make sure the unit is powered down before starting 1 Open the diverse cover 2 Connect MSR Fingerprint iButton to System connector 3 Insert the MSR Fingerprint iButton in place and fasten the screw on the back to secure the module Fingerprint iButton P14 16 Safety information IMPORTANT SAFETY INSTRUCTIONS 1 Carefully read and follow these instructions Pay attention to the danger and caution labels displayed on the product 2 Only operate the product based on the type of power indicated on the label Consult your dealer or local power company if unsure of the type of power available 3 Make sure the power cord is placed safely where it would not be walked on Do not rest anything on the power cord 4 In disconnecting the machine from the electrical power supply first switch off the power button and then remove the power plug from the wall socket 5 This product must not be p
3. laced on an unstable platform such as a stand or table for its fall may cause serious damage to the product 6 Slots and openings are there to provide proper ventilation prevent overheating and ensure reliable operation of the product thus must not be blocked or covered Do not place the product on a bed sofa rug or the like so as to avoid blocking the openings Unless proper ventilation is provided never place the product over or near a radiator heat register or a built in installation 7 Never insert any kind of objects through the openings slots to avoid touching dangerous voltage points which could cause electric shock or fire 8 If there is smoke or strange smell unplug the power cord from the power outlet immediately and request repair from your dealer compatibility C 4 This device complies with the requirements of directive 2004 108 EC with regard to Electromagnetic FCC This device complies with part 15 of the FCC rules Operation is subject to the following two C conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation P15 16 Version Change History Change Date Change Content March 2013 P16 16
4. package contents of your new product Package contents P4 16 Getting to know Front view Zero Bezel Touch screen I Button Fingerprint P5 16 Rear view Cable cover Peripheral dummy cover Peripheral dummy cover Power button LCM display 2 display P6 16 Optional I O interface WU SEL 0 O CS Power DC 19V in Q VGA COCOM OOCOM3 B JCOM2 HOICOM1 P7 16 Specification Chipset NM10 Main Board System Memory SO DIMM DDR3 x1 total up to 4G 1066MHz LCD Size 15 LCD Brightness 300nits True Flat Resistive touch Touch Screen True Flat P CAP touch option cu Intel CedarView D2550 processor 1 86 GHz 1M Cache Storage 1 x 2 5 SATA HDD a Co Cash Drawer sft x RU 11 24V Lao VGA Port 12V power enabled by BIOS Serial Port RJ48 x 4 COM3 5V 0 5A COM4 12V 0 5A selected by BIOS setting Expansion 1 Display PU ini PCI E ternal Sp M Displa SR m In 2nd Display 10 4 LCD 800x600 LCM Display Char x line 2x20 USB interface Peripherals MR ISO 3 Tracks Slim MSR USB interface 1 USB interface 1 USB interface OS Support Windows Embedded POSReady 2009 Windows XP Professional for Embedded Windows 7 65W 19V 4pin Lock FCC Class A CE LVD 430x215x330 0 C 35 C 32 F 95 F 20 C 60 C 4 F 140 F Humidity 20 85 RH non condensing P8 16 Installation Guide Take our
5. the system unit 1 Take the system unit out of the carton Remove the unit from the carton by holding it by the foam inserts 2 Another carton includes the accessories Power adapter 65W power cord COM RJ45 cable x2 and Driver CD P9 16 Install the Power Adapter 1 Remove the Cable cover 2 Route the power adapter through the stand gap 3 Connect the cable to the DC IN port on system IO panel CE P10 16 Install a LCM Customer Display 1 Place the system face down Make sure not to scratch the screen Remove the 2 x screws to open the dummy cover 2 Assemble the LCM customer display hinge into the customer display slot and fasten 2 x screws Route the LCM display cable through the stand gap as shown in the picture 3 Open the cable management and connect the LCM customer display into any USB ports P11 16 Install a Second Display 1 Place the system face down Make sure not to scratch the screen Remove the 2 x screws to open the dummy cover Assemble the 2 display hinge into the customer display slot and fasten 2 x screws Route the 2 display cable through the stand gap as shown in the picture Open the cable management and connect the 2 display into VGA port and adjust voltage to 12V in BIOS refer to Chapter 6 Le Ce y i P12 16 2nd VGA Power Setting gt UGA COM Power and LCD Brightness Configuration Power on the system and press the lt
Download Pdf Manuals
Related Search