manual - Ring Automotive
Contents
1. Ox __ Power POWERING IML aE Compact Inverter Troubleshooting guide PROBLEM Low output voltage Possible Cause MP 120 inverter is overloaded Unsure about the appliance rating Suggested Remedy Reduce load not exceeding MP 120 maximum rating Consider upgrade RINV300 to 3000 Check the data label on the appliance or the instructions If this is unsuccessful consult the manufacturer PROBLEM Re occurring low battery shutdown Possible Cause Inadequate power or excessive voltage drop Poor battery condition Suggested Remedy Check connections from battery to MP 120 inverter Replace or charge battery PROBLEM No power output Possible Cause MP 120 inverter in thermal shut down condition Low battery voltage MP 120 inverter blown fuse Vehicle blown fuse DC socket Poor DC plug connection Suggested Remedy Remove power and load allow to cool 10 minutes Charge or replace battery Check replace the 15 Amp fuse in the DC plug Check vehicle handbook to locate relevant fuse Use the DC plug switch to ensure a good connection PROBLEM Liquid ingress Possible Cause Drinks spillage Suggested Remedy Unplug the MP 120 inverter and wipe immediately with a dry cloth Permanent damage can occur with liquid ingress PROBLEM No power output from USB socket Possible Cause Appliance is not rechargeable USB not inserted correctly Suggested Remedy Check appliance is re2. chargeable and uses rechargeable batteries Check connections are the correct way up with the USB symbol facing up on the USB plug USB SPECIFICATIONS PowerSource Model MP 120 inverter Part Number 120w 30 mins 100w 4 hours Max Continuous power Watts RINV120 Peak Power Watts 0 01 Seconds 240w Standby current Amps lt 0 2A Waveform Modified Sine Wave Efficiency 90 Input Voltage Range 10v 15v DC AC Socket 3 Pin mains 230v AC USB socket USB2 DC5v 150mA Cooling Fan Yes Continuous Product Dimensions mm D x H x W 30x 105 x 75 Pack Dimensions mm D x H x W 55 x 180 x 185 Coiled Cable length mm 650 extended length Percentage of battery power to mains voltage power CE approved This inverter should only be used to power Class II non earthed products identified by the symbol m Distributed by Ring Automotive Limited Gelderd Road Leeds England LS12 6NA Automotive amp 44 0 113 213 2000 44 0 113 231 0266 autosales ringautomotive co uk www ringautomotive co uk Portable Power POWERING IMAL BESS Compact Inverter 12v DC to 230v AC Mains Inverter RINV120 User Manual www ringautomotive co uk RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE x __ Power POWERING Introduction The Ring MP 120 inverter is an electronic device that converts a low voltage 12v DC current from a battery or oth
3. er power supply and provides 230v AC current Special attention should be made to CAUTION statements in this user manual CAUTION statements identify conditions or practices that could result in damage to your MP 120 or to the equipment you are using with it CAUTION Do not exceed the maximum input voltage 15 Volts DC Improper use of the MP 120 inverter can cause damage to property and possibly harm to the user e The MP 120 contains no user serviceable parts Do not open Power Supply The battery or power supply must provide between 10 5 and 14 5 Volts DC a car battery will usually provide this and must be able to provide sufficient current to operate the load the item you require to power The power supply used may be a battery or a regulated DC power supply In order to find out if your power supply is large enough divide the power consumption of the load in watts by the voltage 12v in the case of the MP 120 inverter this will give you the current in amps that the power supply must deliver EXAMPLE Load is rated at 48W 12v 4 Amps Connecting to your power supply Connect the DC plug on the MP 120 inverter to the vehicle battery by plugging directly into the 12v DC socket cigarette lighter socket The LED power monitor illuminates green when power is on The MP 120 must only be used on vehicles where the centre contact of the cigarette lighter socket holder is positive Ensure the load requirements are within the s
4. mperature Protection If the temperature of the internal heat sink reaches gt 65 C the MP 120 will shut down automatically Remove from power and allow to reset when cool before using Cooling Fan The internal cooling fan runs continuously once the MP 120 is connected to a power supply to optimise performance
5. pecification max 120w of the MP 120 output Plug your appliance into either the 3 pin or USB socket of the MP 120 inverter Positioning of the MP 120 inverter Included in the pack are two pieces of hook and eye tape to allow for the most suitable positioning of the MP 120 inverter in your vehicle By use of the hook and eye tape the MP 120 can be removed from the vehicle when left unattended When positioning the following points should be noted CAUTION e The MP 120 inverter is not waterproof e Take care if adjacent drinks holders contain or have contained liquids The MP 120 should be used in a ventilated area Do not obstruct the vents at the front and side of the MP 120 Do not put the MP 120 on or near sources of direct heat or expose to direct sunlight Do not operate the MP 120 in or around flammable environments e Ensure cables and leads connected to the MP 120 do not interfere in the safe operation of the vehicle e When not in use store securely in a cool dry dust free environment Do not leave connected to 12v DC socket unattended Remove from 12v DC socket when not in use as the unit will continue to draw 0 4 Amps stand by current Do not operate continuously for more than 4 hours Do not use the power lead to move or carry the MP 120 e The USB socket is for charging only NOT data transfer 2 MIP alee Compact Inverter Operating Tips NOTE The MP 120 inverter is not designed to run products
6. that provide heat such as hair dryers heaters and irons Do not handle the MP 120 inverter with wet hands or if it has come into contact with liquid Ensure while driving all accessories powered by the MP 120 inverter are positioned securely Do not use distracting accessories such as mobile phones whilst driving To ensure optimum performance from the MP 120 adjust the DC plug switch for the correct fit in the vehicle s DC socket Ensure the USB plug is inserted correctly in the socket With the USB symbol facing up The MP 120 uses a USB2 type socket and will therefore charge USB1 amp USB2 devices Maintenance Cleaning Only clean the MP 120 inverter using a clean dry cloth Do not use cleaning products Ensure the USB socket is clear of any dust or other debris before connection Fuse Replacement The fuse is located in the MP 120 DC plug Unscrew the end of the DC plug and extract the 15 Amp fuse Check the fuse and replace if necessary with an equivalent 15 Amp fuse Protective features Auto shutdown The MP 120 inverter will automatically shut down if the supply voltage is less than 10v At this point the green LED will go out The inverter will automatically restart when the input voltage is above 10v Overload protection The MP 120 inverter will automatically shut down if the continuous power draw exceeds the maximum rating Short circuit protection via automatic thermal resetting fuse Te
Download Pdf Manuals
Related Search