Network Camera - WebcamCenter.nl
Contents
1. SNC DH110 DH210 106 4 4 SNC DH110T DH210T 106 4 4 Unit mm inches Preparations Connect the sensor input cable to the camera D Before installation connect the supplied sensor input cable to the camera according to your usage environment Wiring diagram for sensor input Mechanical switch open collector output device Camera inside Outside 3 3 V Mechanical switch Sensor input Sensor input GND or ppke Open collector GND GND GND output device Attaching the fall prevention rope E When you install the camera on a ceiling or a high location be sure to attach a fall prevention rope not supplied to prevent the camera from falling Thread the fall prevention rope through the hole on the camera as in the illustration and then fix it to the junction box on the ceiling or wall with a screw not supplied For details about the fall prevention rope please consult the store of purchase or an authorized Sony dealer Installation If you attach the camera in the height such as the wall or the ceiling etc entrust the installation to an experienced contractor or installer e If you install the camera on the ceiling ensure that the ceiling is strong enough to withstand the weight of the camera and then install the camera securely If the ceiling is not strong enough the camera2. 2 Select and click on the manual that you want to read This opens the PDF file of the manual Clicking an item in the Table of Contents allows you jump to the relevant page The files may not be displayed properly depending on the version of Adobe Reader In this case install the latest version which you can download from the URL mentioned in Preparations above Ifyou have lost or damaged the CD ROM you can purchase replacement Contact your Sony service representative Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United States and or other countries Location and Function of Part Appearance Dome casing PT Pan Tilt casing Care should be taken while turning the PT casing as it may separate if pulled it too hard Should this occur see When the PT casing separates on the reverse side and install the casing correctly lens casing Normal cover SNC DH110 DH210 only Clear cover SNC DH110T DH210T only Hook Press the hook inward and meanwhile turn the dome casing then remove the dome casing from the camera unit Knockout type flange When threading the cables through the side of the camera use pliers to break off the knockout flange with pliers etc TOP E The figure shows the camera without the dome casing and the cover Camera unit Lens A fixed focus lens is mounted Reset switch If you hold down this switch for about 40 sec
3. casing counter clockwise When the PT casing separates 1 Ifthe camerais installed on the ceiling or wall detach the camera unit first 2 Push inwards and hold the bottom of the flat spring on the camera to avoid it springing out 3 Make sure to align the little cube projection on the inside of the PT casing with the notch of the camera as in the illustration 4 Set the slits of PT casing 4 positions closely with the flat spring of the camera then press the PT casing down gently Make sure not to press at the top of flat spring otherwise it may cause deformation When you find the PT casing can not be easily clicked with the camera unit check the direction of the PT casing and whether the slits are aligned with the flat spring again Push the casing forcedly may cause the damage Compression Video compression format Maximum frame rate JPEG MPEG4 H 264 JPEG MPEG4 H 264 30 fps 1280 x 720 16 9 mode Camera Image device SNC DH110 DH110T 1 3 8 type CMOS Effective picture elements Approx 1 280 000 SNC DH210 DH210T 1 2 8 type CMOS Exmor Effective picture elements Approx 3 270 000 SNC DH110 5 0 Ix AGC max 50 IRE IP SNC DH110T 5 5 Ix AGC max 50 IRE IP SNC DH210 2 0 Ix AGC max 50 IRE IP SNC DH210T 2 3 Ix AGC max 50 IRE IP Minimum illumination Lens Focal length SNC DH110 DH110T 2 34 mm SNC DH210 DH210T 3 3 mm Maximum relative aperture F2 8 View angle SNC DH110 Hor
4. de la classe A est conforme la norme NMB 003 du Canada For the customers in Europe The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents For the customers in Europe Australia and New Zealand WARNING for model SNC DH210 DH210T only This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures In the case that interference should occur consult your nearest authorized Sony service facility This apparatus shall not be used in the residential area ATTENTION The electromagnetic fields at specific frequencies may influence the picture of the unit SNC DH110 DH210 Notes on Use Before Use If you find condensation before use leave the camera out for long enough and do not turn on the power until the condensation disappear Remove static electricity before installation and operation Data and security You should keep in mind that the images or audio you are monitoring may be protected by privacy and other legal rights and the responsibility for making sure you are complying with applicable laws is yours alone Access to the
5. television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Model SNC DH210 DH210T NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense For customers in Canada Model SNC DH110 DH110T This Class B digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada Model SNC DH210 DH210T This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique
6. 4 261 054 12 1 SONY Network Camera Installation Manual Before operating the unit please read this manual thoroughly and retain it for future reference IMPRELA HD SNC DH110 DH110T SNC DH210 DH210T http www sony net 2010 Sony Corporation Printed in China Owner s Record The model and serial numbers are located on the bottom Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No To reduce a risk of fire or electric shock do not expose this product to rain or moisture Serial No To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only WARNING This installation should be made by a qualified service person and should conform to all local codes WARNING A readily accessible disconnect device shall be incorporated in the building installation wiring WARNING for Installers only Instructions for installing the equipment on the ceiling or the wall After the installation ensure the connection is capable of supporting at least a force of 50 Newtons N downwards CAUTION The rating label is located on the bottom CAUTION Use shielded LAN cables to install the SNC DH110 DH110T CAUTION for LAN port For safety reason do not connect the LAN port to any network devices that might have excessive voltage The LAN port of this unit is to be connected onl
7. OR FOR ANY OTHER REASON WHATSOEVER If you lose data by using this unit SONY accepts no responsibility for restoration of the data Personal information The images taken by the system using this device can identify individuals and thus they fall under personal information stipulated in the Act on the Protection of Personal Information Please handle the video data appropriately according to law Information recorded using this product may also be personal information Upon disposal transfer repair or any other occasion where this product or storage media is passed on to a third party practice due care in its handling Operating or storage location Do not shoot an extremely bright object an illumination the sun etc Also avoid operating or storing the camera in the following locations as these can be a cause of a malfunction Extremely hot or cold places Operating temperature 0 C to 50 C 32 F to 122 F Exposed to direct sunlight for a long time or close to heating equipment e g near heaters Close to sources of strong magnetism Close to sources of powerful electromagnetic radiation such as radios or TV transmitters Locations subject to strong vibration or shock Humid or dusty locations Locations exposed to rain Locations under the influence of fluorescent light or reflection of a window Under an unsteady light the image will flicker Ventilation To prevent heat buildup do n
8. images and audio is protected only by a user name and the password you set up No further authentication is provided nor should you presume that any other protective filtering is done by the service Since the service is Internet based there is a risk that the image or audio you are monitoring can be viewed or used by a third party via the network SONY IS NOT RESPONSIBLE AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR ANYONE ELSE FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR EVEN SERVICE CANCELLATION THE SERVICE IS PROVIDED AS IS AND SONY DISCLAIMS AND EXCLUDES ALL WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO THE SERVICE INCLUDING BUT NOT LIMITED TO ANY OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR THAT IT WILL OPERATE ERROR FREE OR CONTINUOUSLY Always make a test recording and verify that it was recorded successfully SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS RECORDING MEDIA EXTERNAL STORAGE SYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE Always verify that the unit is operating properly before use SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY
9. izontal 80 7 Vertical 63 3 4 3 mode SNC DH110T Horizontal 79 Vertical 62 4 3 mode SNC DH210 Horizontal 88 Vertical 65 4 3 mode SNC DH210T Horizontal 86 Vertical 64 4 3 mode Minimum object distance 0 5 m Interface LAN PoE 10BASE T 100BASE TX auto negotiation RJ 45 1 port make contact and break contact switchable Sensor input Monitor out NTSC PAL 1 0 Vp p 75 ohms unbalanced sync negative AV minijack Use AV cable with mini plug at AV4 terminal Others Power IEEE802 3af compliant PoE system Class 1 Power consumption 24W Operating temperature Storage temperature 0 C 50 C 32 F to 122 F 20 C to 60 C 4 F to 140 F Operating humidity 20 to 80 Non condensing Storage humidity 20 to 95 Dimensions diameter x height SNC DH110 DH210 106 mm x 50 5 mm 4 inches x 2 inches SNC DH110T DH210T 106 mm x 56 5 mm 4 1 4 inches x 2 inches Mass SNC DH110 DH210 Approx 160 g 5 6 oz not including the cables SNC DH110T DH210T Approx 170 g 6 0 oz not including the cables CD ROM User s Guides and supplied programs 1 Template 1 Sensor input cable 1 Installation Manual this document 1 Supplied accessories Design and specifications are subject to change without notice Recommendation of Periodic Inspections In case using this device over an extended period of time please have it inspected periodically for safe use I
10. m for Power over Ethernet IEEE 802 3af standard compliant devices Sensor Input Connect the supplied sensor input cable The cable is not connected when the unit comes from the factory Sensor input R cable color Signal Red Sensor input White Sensor input GND For details on function and required settings refer to the User s Guide stored in the supplied CD ROM For the wiring see Wiring diagram for sensor input Camera installation hole 2 positions Make sure to tighten the screws securely when installing the camera Model name label This label shows device information such as the model name and serial number MAC Address label Indicates the MAC address of this camera continued on the reverse side D LAN connector Sensor input Rope not supplied SNC DH110 DH110T 57 SNC DH210 DH210T 60 Adjustable angle of lens Pan Hole for connecting cables G28 Screw hole Unit mm inches Ceiling LAN cable Network cable straight not 100BASE TX PoE supported device such as Rope not supplied AS i ee Cube projection Slots for flat spring
11. may fall and cause serious injury To prevent the camera from falling make sure to attach the fall prevention rope not supplied e If you attach the camera to the ceiling check periodically at least once a year to ensure that the connection has not loosened If conditions warrant make this periodic check more frequently Deciding the Installation Location of the Camera After deciding the direction in which the camera will shoot use the supplied template to decide the location of the hole for connecting cables and required screw holes Make the hole for connecting cables 28 mm When threading the cables through the side of the camera there is no need to make the hole for connecting cables Connect to the Network Connect the LAN connector of the camera to a PoE supported device such as a hub using the network cable straight not supplied The electrical power is supplied through the network cable For details refer to the instruction manuals of the PoE supported devices PoE The acronym for Power over Ethernet IEEE 802 3af standard compliant devices Installing the Camera 1 Remove the dome casing Press the hook and meanwhile turn the dome casing in the counterclockwise direction then remove the dome casing from the camera unit 2 Fix the fall prevention rope not supplied to the ceiling or wall 3 Install the camera The supplied template indicates the location of screw holes to be made in the ceili
12. ng or wall Align with the 2 screw holes in the camera and fix the screws not supplied Mounting screws The required mounting screws differ depending on the installation location and its material Mounting screws are not supplied Steel wall or ceiling Use M4 bolts and nuts Wooden wall or ceiling Use M4 tapping screws The panel thickness must be 15 mm s inch or more Concrete wall Use anchors bolts and plugs suitable for concrete walls Junction box Use screws to match the holes on the junction box The required mounting screws differ depending on the installation location and its material If you do not secure the camera with the appropriate mounting screws the camera may fall off Take care not to trap the cables between the camera and the ceiling or the wall If the cable is trapped it may cause a fire or electric shock due to breaking Adjusting the Camera Direction and Coverage Turn the PT casing and lens casing to adjust the pan and tilt directions separately then you are able to turn the lens in the desired shoot direction You can turn the PT casing by holding it If you pull the PT casing it may separate As you rotate the lens it may reach a stop In this case do not force the lens instead turn the lens in the opposite direction to select the shoot direction Do not pull the PT casing as it may separate Should this occur see When the PT casing separates and install the casing correctly U
13. onds when the camera is on normal operation the POWER indicator turns off and the NETWORK indicator lights up in orange and then the camera will be reset to the factory default settings and restarted MONITOR out connector AV minijack Output the composite video signal from the camera Monitor out is used when you adjust the view angle Before use see the procedure from Setting the view angle of the monitor out Before use it is neseccery to connect to the PC and change the system setting POWER indicator Green When the power is supplied to the camera the camera starts checking the system If the system is normal this indicator lights up NETWORK indicator Green Orange The indicator lights up or flashes when the camera is connected to the network The indicator is off when the camera is not connected to the network When 100BASE TX is connected the indicator turns green When 10BASE T is connected the indicator turns orange NTSC PAL switch Switching the video output Bottom Fall prevention rope mounting hole When installing the camera on a ceiling or a wall Be sure to secure a fall prevention rope not supplied to this hole for safety LAN connector PoE RJ 45 Use the network cable UTP category 5 for network communications and PoE power supply LAN cable RJ 45 is connected when the unit comes from the factory See Connect to the Network for connection PoE The acrony
14. ot block air circulation around the camera Power supply The power of this model is supplied by network cable Use the network cable UTP category 5 Damage to the network cable may result in fire or electric shock Transportation Always turn off the power when carrying When transporting the camera repack it as originally packed at the factory or in materials of equal quality Cleaning Use a blower to remove dust from the lens Use a soft dry cloth to clean the external surfaces of the camera Stubborn stains can be removed using a soft cloth dampened with a small quantity of detergent solution then wipe dry Do not use volatile solvents such as alcohol benzene or thinners as they may damage the surface finishes Note on laser beams Laser beams may damage image sensors You are cautioned that the surface of image sensors should not be exposed to laser beam radiation in an environment where a laser beam device is used Phenomena Specific to Image Sensors The following phenomena that may occur in images are specific to image sensors They do not indicate a malfunction White flecks Although the image sensors are produced with high precision technologies fine white flecks may be generated on the screen in rare cases caused by cosmic rays etc This is related to the principle of image sensors and is not a malfunction The white flecks especially tend to be seen in the following cases
15. sing the monitor out Setting the view angle of the monitor out 1 Make sure the POWER indicator lights up 2 Select the installation tab in system setting menu then set monitor out to On 3 Connect the AV cable to the monitor out AV minijack 4 Adjust the view angle 5 Select the installation tab in system setting menu then set monitor out to Off 6 Disconnect the AV cable The system setting is changed from PC For details on required settings see the User s Guide stored in the supplied CD ROM Connect the AV cable when the POWER indicator lights up Be aware that the system performance may be influenced if the monitor out is set to On Be sure to set it to Off and disconnect the AV cable Attaching the Dome Casing 1 1 Check the dome casing inside As in the illustration make sure the projection on the normal cover or on the clear cover is fully engaged with the notch of the dome casing 2 Align the rectangle white marker on the printed circuit board with the notch of the dome casing then turn the dome casing in the direction of arrow to fasten it tightly 3 Remove the protecting film on the clear cover When threading the cables through the side of the camera use pliers to break off the knockout flange with pliers etc How to remove the dome casing after installation While pushing slightly on the hook with a minus screwdriver or thin instrument of approx 1 mm diameter turn the dome
16. t may appear flawless but the components may have deteriorated over time which may cause a malfunction or accident For details please consult the store of purchase or an authorized Sony dealer
17. when operating at a high environmental temperature when you have raised the gain sensitivity when using the slow shutter Aliasing When fine patterns stripes or lines are shot they may appear jagged or flicker SNC DH110T DH210T About the Supplied Manuals Installation Manual this document This Installation Manual describes the names and functions of parts and controls of the Network Camera gives connection examples and explains how to set up the camera Be sure to read the Installation Manual before operating The pictures of SNC DH210T are mainly used in explanatory examples User s Guide stored in the CD ROM The User s Guide describes how to set up the camera and how to control the camera via a Web browser After installing and connecting the camera correctly operate referring to this User s Guide Using the CD ROM Manuals The supplied CD ROM disc includes the User s Guides for this unit in PDF format Preparations The Adobe Reader Version 6 0 or higher must be installed on your computer in order to use the guides stored in the CD ROM disc If Adobe Reader is not installed it may be downloaded from the following URL http www adobe com Reading the manual in the CD ROM 1 Insert the CD ROM in your CD ROM drive A cover page appears automatically in your Web browser If it does not appear automatically in the Web browser double click on the index htm file on the CD ROM
18. y to the devices whose power feeding meets the requirements for SELV Safety Extra Low Voltage and complies with Limited Power Source according to IEC 60950 1 Use IEEE802 3af standard compliant devices For customers in the U S A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B or Part 15 of FCC Rules Model SNC DH110 DH110T NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or
Download Pdf Manuals
Related Search