Home

- Frank`s Hospital Workshop

image

Contents

1. Racks Crossover Assemblies or Squeegee Rollers 5 Remove the Evaporation Covers and the Crossover Assemblies a Rinse the Evaporation Covers b Rinse the developer fixer and fixer wash Crossover Assemblies in warm water 6 Rotate and clean the Rollers with a soft brush and warm water CROSSOVER ASSEMBLIES 7 Dry the Rollers with a cloth or synthetic sponge DETECTOR CROSSOVER FEED ASSEMBLY SHELF H112_0066CCB H112 0066CC 8 Wipe off all chemical deposits above the solution level in the processing section 9 Clean off debris or buildup from the dryer area with a warm damp sponge or cloth 10 Install the Crossover Assemblies and the Evaporation Covers 11 Install the Top Cover leaving a5 cm 2 in gap Keep the Top Cover open overnight for venting purposes Use only qualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures 15 OPERATOR MANUAL Every Two Weeks Figure 13 Biweekly Cleaning of the Racks and Crossovers DRYER ASSEMBLY GUIDE CROSSOVER ASSEMBLIES DETECTOR CROSSOVER FEED ASSEMBLY SHELF H112_0066CCB H112 0066CC A Warning Dangerous Voltage Disconnect the main power before doing any of the following cleanup procedures 1 Turn off the Main Power Switch 2 Disconnect the main power 3 Turn off the water supply 4 Remove the Top Cover Caution e When removin
2. When the Fixer Tank is drained install the blue Weir 5 Drain the Developer Tank in the same way Use only qualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures OPERATOR MANUAL A Important Do not interchange the weirs Weir Tank red developer blue fixer beige wash Filling the Tanks Figure 9 Filling the Tanks Caution FILL solutions to avoid contamination of the solutions ea N EINES e Mix the developer first then the fixer a Xx e Wash the mixing equipment thoroughly between 7 Ad a 2 e Rinse the mixing and filling equipment before each a pe 5 PRS use WE eee Fill the Fixer Tank first nae E Ys eae lt 1 Install the Splash Guard between the Developer N replenisher until the solution is at the higher Fill FIXER DEVELOPER Line on the blue Weir Tank and the Fixer Tank See Figure 7 on page 8 WASH tank TANK Hi Sake ANK 3 Remove and rinse the Splash Guard 4 Install the Splash Guard over the Fixer Tank 2 To fill the processor Fixer Tank add fixer 5 To fill the processor Developer Tank a Fill the Developer Tank half full of developer replenisher from the replenisher tank b Add 190 mL 6 5 fl oz of KODAK RP X OMAT Developer Starter c Fill the Developer Tank to the higher Fill Line on the red Weir with developer replenisher 6 Remove the Splash Guard and rinse thoroughly 7 Install the Racks in t
3. temperature of the developer is correct for the mode selected Standard or Extended If necessary have gualified service personnel make adjustments NOTE Check the incoming water temperature It must be a minimum of 4 C 7 F lower than the desired developer temperature Check that the correct Bulb is in the Safelight If the digital temperature display is blank and all noise ceases including the Main Drive Motor and the Ventilation Fan turn off the main power and the Main Power Switch on the Processor Check that the problem film is compatible with the mode selected Standard or Extended Use only gualified service personnel to perform 14 all necessary adjustments and procedures 09JUL98 981158 Cleanup and Periodic Maintenance Section 6 Cleanup and Periodic Maintenance Daily Figure 12 Daily Cleaning of the Racks and Crossovers A Warning Dangerous Voltage Disconnect the main power before doing any of the following cleanup procedures gt Note The best time to do daily cleanup is at shutdown DRYER 1 Turn off the Main Power Switch ASSEMBLY GUIDE 2 Disconnect the main power 3 Turn off the water supply 4 Remove the Top Cover Caution e When removing the Crossover Assemblies be careful not to twist them out of square or disturb the Guide Shoes e Use a damp cloth or a synthetic sponge and warm water Do not use any abrasive material on the
4. 0 3 C 92 0 F t0 5 F The immersion time in the developer solution is 33 seconds A film feed signal sounds 3 seconds after the film being processed has cleared the rollers of the Detector Crossover Assembly This indicates that the processor is ready to accept another piece of film Publication Part Numbers This publication is part of a series of instruction books that provide technical support information on the KODAK M35 and M35A X OMAT Processors It is recommended that these publications be kept in the binder provided If an individual book is misplaced or destroyed order another copy from your Eastman Kodak Representative using the Publication Part Numbers below Figure 1 Related Publications for the M35 and M35A Processors COMPLETE BINDER 981797 OPERATOR INSTALLATION SERVICE MANUAL ae a INSTRUCTIONS MANUAL 981159 981777 PARTS LIST 981778 981158 H112_9002BC Use only qualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures 3 OPERATOR MANUAL Section 2 Processing Film Start Up Figure 2 Main Power Switch TOP COVER S A H112_0089ACB H112_0089AC MAIN POWER SWITCH Figure3 Water Inlet Tube of the Wash Tank EVAPORATION WATER COVER 2 INLET TUBE DRYER TEMPERATURE CONTROL KNOB H112_0140ACA H112_0140AC A Warning Keep fingers clothing cleaning materials etc away from the moving parts of the processo
5. 112_0114AC 7 When the Replenishment Pump stops check that the amount of solution in the Graduated Cylinder is the same as in the table on page 14 If the amount is not correct contact qualified service personnel 8 Connect the Developer Tubing again by pushing it into the Metal Latch until the Developer Tubing locks in place 9 Check the fixer replenishment flow rate by doing steps 3 8 with the Fixer Tubing 10 Install the Top Cover Figure 11 Detector Crossover Assembly UPPER ROLLER DETECTOR CROSSOVER ASSEMBLY DETECTOR SWITCH 2 H112 0121BCB H112 0121BA Use only gualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures 11 OPERATOR MANUAL Table 1 Setting Replenishment Flow Rates Replenishment Flow Rate Average Amount mL per 35 cm 14 in mL per 43 cm 17 in of Film 28 seconds 34 seconds Film Size Use per 8 Hours of of Film Travel of Film Travel Processed Condition Processor Operation Developer Fixer Developer Fixer Only 35 x 35 cm High 90 sheets or more 50 70 14 x 14 in film Medium 60 sheets 65 85 Low 30 sheets or less 80 100 Average size High 115 sheets or more 50 70 film intermix Medium 80 sheets 65 85 Low 40 sheets or less 80 100 Only 35 x 43 cm High 75 sheets or more 60 85 14x 17 in film Medium 50 sheets 80 100 Low 25 sheets or less 100 120 L gt Note KODAK R
6. 8 09JUL98 all necessary adjustments and procedures 19 OPERATOR MANUAL Figure 18 Splash Guard and Drip Tray DRIP TRAY SPLASH GUARD 7 a LO Ai ae H112_0015ACA H112_0015AC Caution When installing the Racks use the Splash Guard Lower the Racks slowly g Install the Racks the Crossover Assemblies and the Dryer Assembly Check that each assembly seats firmly h Turn on the main power the water and the processor i Check the solutions If the surfaces of the solutions are moving the recirculation pumps are operating j When the Temperature Ready Light flashes use a thermometer of known accuracy and check the solution temperature in the developer Tank The correct temperature is 33 3 C 0 3 C 92 0 F 0 5 F 2 If the processor handles a high volume 25 sheets of film day or more do steps a j on a monthly basis Use only qualified service personnel to perform 20 all necessary adjustments and procedures 09JUL98 981158 New Equipment Warranty Section 7 New Equipment Warranty Warranty Coverage Kodak warrants this KODAK M35 or M35A X OMAT Processors to function properly for 6 months from the date of initial installation when installed within one year from the date of shipment If this equipment does not function properly during the warranty period the dealer for KODAK X OMAT Processors who sold the equipment will provide or arrange for repair of the equipment during the dealer s normal w
7. P X OMAT Chemicals are recommended Replenishment rates are based on one sheet of film Film feeding orientation should be consistent for best results e Slight sensitometric changes will occur as subsequent films are processed through a freshly started process This is known as seasoning and is normal with any photographic process Process control aims may have to be adjusted slightly to compensate e For 30 sheets or less flooded replenishment is recommended 12 Use only qualified service personnel to perform all necessary adjustments and procedures 09JUL98 981158 Correcting Difficulties Section 5 Correcting Difficulties 1 Transport Failure 2 Surface Artifacts 3 Abnormal Film Densities 4 Wet Films 5 Low Solution Levels 6 Overlapping of Films Film Feeding Error Feed only single thicknesses of film Feed the next film only after the film feed signal sounds If there is no film feed signal refer the difficulty to qualified service personnel Feed only compatible films Check that all Racks and Crossovers are seated correctly Check that the surfaces of all the Rollers are clean and smooth especially in the Developer Turnaround Assembly Check that the Dryer Air Tubes are in the correct positions Remove any dirt from the Dryer Rollers and Air Tubes especially the slots Use a bottle brush and rinse with water Check the replenishment se
8. Publication No 981158 09JUL98 Supersedes 981158 160CT97 OPERATOR S MANUAL for the Kodak M35 X Omat PROCESSOR Kodak M35A X Omat PROCESSOR 9 L R3 A MM LA ZR d 0 Z H112_0043AC Ka HEALTH IMAGING Eastman Kodak Company PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the subject matter gained by Eastman Kodak Company prior to publication No patent license is granted by this information Eastman Kodak Company reserves the right to change this information without notice and makes no warranty express or implied with respect to this information Kodak shall not be liable for any loss or damage including consequential or special damages resulting from any use of this information even if loss or damage is caused by Kodak s negligence or other fault Table of Contents Description Page OVERVIEW ani ben es end EA wea eed dota ond Se eed ath be dew dae wit eet ows 3 Description Pan aera ates Sees RE ae oe RN Ra cused an Sit ae Boe 2 3 Publication Part Numbers eens 3 Processing Filim sio edan uban nan nan Me su bun la 4 DAU Paten e s Sinar ant terb wats toe owe ak GE bb em NE gna witee ota eee quel 4 Feeding Sheet FUM 5 000 0 ee acme egadtnts weed wera ee koe E 6 Feeding 35 mm Roll Film ii 1 Shutdown ken eta bihan nba BN BEA BAN NE ENG SE ANA 7 Processing Solutions ii 8 Preparatio
9. SSOVER ASSEMBLY H112_0066CCD H112 0066CC 5 Install the Top Cover on the processor 6 Press the Run Standby Switch gt Note The Temperature Ready Light flashes when the developer solution is at the correct temperature for processing film 7 Feed a sheet of KODAK Roller Transport Cleanup Film CAT No 166 2303 into the processor when the Temperature Ready Light flashes The recommended temperature is 33 3 C 0 3 C 92 0 F 0 5 F Adjust the Dryer Temperature Control Knob to the lowest setting to dry the film 8 i 981158 09JUL98 Use only qualified service personnel to perform all necessary adjustments and procedures 5 OPERATOR MANUAL Feeding Sheet Film gt Note e The motors will begin to operate 35 x 35 cm sa e After film removal the processor will 14x14 in automatically return to the standby mode 35 x 43 cm or e The Temperature Ready Light flashes when kada the developer solution is at the correct temperature for processing film 2 Feed a sheet of film emulsion side up into the processor gt Note A film feed signal will sound 3 seconds after the trailing 5430 cin 24x 24 cm edge of a sheet of film has left the rollers of the Detector A Crossover Assembly 10 x 12 in 1 each 2 each 10 x 10 cm 18 x 24 cm or 4x4in 18 x 43 cm 11x14in H112 9001CC Use only gualified service personnel to perform 6 all necessary adjustments an
10. d procedures 09JUL98 981158 Processing Film Feeding 35 mm Roll Film Caution e The leader must be at least 18 cm 7 inches long and 35 mm wide e The adhesive side of the tape must not be exposed e Other types of tape are unacceptable because their bases are soluble in the processing solutions 1 Use a sheet of film as a leader 2 Use 2 cm 1 inch wide 3M SCOTCH Brand Polyester Film Tape No 850 to connect the sheet of film to the roll film S TEMPERATURE RUN STANDBY aaah A SWITCH H112_0089AC Shutdown Figure 6 Processor in Shutdown Mode TOP COVER SWITCH H112_0141ACA H112 0141AC 1 Turn off the Main Power Switch and the water supply 2 Disconnect the main power 3 Remove the Top Cover and Evaporation Covers 4 Do the Daily cleanup procedure on page 19 5 Install the Top Cover with a 5 cm 2 in opening A Important Keep the Top Cover open overnight for venting purposes 981158 09JUL98 Use only qualified service personnel to perform all necessary adjustments and procedures OPERATOR MANUAL Section 3 Processing Solutions Preparation Figure 7 Processing Tanks with the Splash Guard and the Drip Tray DRIP TRAY SPLASH GUARD NA 2 Sy NG H112 0015ACA H112 0015AC Caution Avoid contamination of the processing solutions e To avoid spilling solutions from one tank into the next one use the Splash Guard between th
11. e developer and fixer Tanks e Slowly install or remove the Racks e Use the Drip Tray when moving Racks to or from the processor 1 Mix the volume of processing solution required in the correct replenisher tank Use the instructions packed with the chemicals to mix the solution G Important Do not mix more than a 2 week supply for replenisher tanks with floatation lids 2 Remove the Crossover Assembly and the Rack from the Tank that is to be filled Use only qualified service personnel to perform 8 all necessary adjustments and procedures 09JUL98 981158 Processing Solutions Draining the Tanks Figure 8 Draining the Tanks WATER INLET fixer fixer x DRAIN 3 developer developer H112_0071DCB H112_0071DA Caution e Drain only one Tank at a time e Make certain that all drain materials and fluids comply with local state and federal regulations e Relatively small amounts of fixer can seriously contaminate the developer If solutions are changed in both Tanks fill the Fixer Tank first so that any solution spilling into the Developer Tank can be thoroughly cleaned 1 If the processor has a Silver Recovery Unit connected disconnect the fixer drain tube at the input side of the Silver Recovery Unit See Figure 14 on page 19 2 Lift the blue Weir from the Fixer Tank 3 Drain the fixer solution Check the local codes for the correct disposal procedures 4
12. e Replenishment Strainer Assemblies STRAINER ASSEMBLY 5 r Q c Ara De Z L Fi A EE TN i SCREEN H112 0092BCA H112 0092BA Use only gualified service personnel to perform 18 all necessary adjustments and procedures 09JUL98 981158 Cleanup and Periodic Maintenance Special Maintenance for Low or High Volume Usage 1 If the processor handles a low volume 25 sheets of film or less a day do the following every 2 weeks Caution If the PROCESSOR has a Silver Recovery Unit attached drain only one Tank at atime When draining the Fixer Tank disconnect the Drain Tube at the input side of the Silver Recovery Unit and direct it to the Floor Drain before lifting the Weir a Remove the Weirs on the developer and fixer Tanks See Figure 17 b Drain the Tanks c Flush with clean water d Install the Weirs red for developer and blue for fixer e To fill the processor fixer Tank add fixer replenisher until the solution is at the higher Fill Line on the blue Weir f To fill the processor developer Tank Add 190 mL 6 5 fl oz of KODAK RP X OMAT Developer Starter Fill the developer Tank to the higher Fill Line on the red Weir with developer replenisher solution Figure 17 Weirs H112 0014ACB H112_0014AC Use only qualified service personnel to perform 98115
13. e developer and fixer Tanks e Use the Drip Tray when removing or installing the Racks See Figure 7 on page 8 e Do not rinse the Detector Crossover Assembly or the Dryer Assembly 11 Remove the Racks 12 Rinse the Racks and wipe them with a cloth 13 Check the following a that the Chains move freely and are adjusted correctly b that all the Rollers rotate correctly c that the space between the Turnaround Side Plates and the Rack Side Plates is equal and that the Side Plates are parallel on both ends 14 Check the operation of the Silver Recovery Unit if installed 15 Check that no solution is flowing through the Bypass gt Note If solution is present in the Bypass the Silver Recovery Unit is not operating 16 Use KODAK Silver Estimating Test Papers CAT No 196 5466 to check the silver content of the solution flowing into the drain 17 If the test shows more than 1 gram litre of silver install a new cartridge in the Silver Recovery Unit Use only qualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures 17 OPERATOR MANUAL 18 Clean the Replenishment Strainers when mixing new chemicals a Place pinch clamps on the tubing to stop the replenishment flow b Disassemble the Strainer Assemblies c Use a brush and warm water to clean the Strainer Assemblies and to remove dirt and chemical deposits from the Screens Figure 16 Cleaning th
14. ervices or claims of your customers for such damages e This limitation of liability will not apply to claims for injury to persons or damage to property caused by the sole negligence or fault of Kodak or by persons under its direction or control Publication History Affected Print Date Pub No ECO No Pages File Name Notes OISEP92 981158 4014 318 All 3047cm_a txt Supersedes Publications No 635816 and 635037 The previous operating instructions for the M35 and M35A Processors were combined into one manual and the information updated 160CT97 981158 4014 457 All o0m3041_1_loct97 doc deleted steps that required the customer to do procedures that only qualified service personnel should do O9JUL98 981158 4014 473 All om3041 1 09jul98 doc For MDD compliance deleted steps that reguired the customer to do procedures that only gualified service personnel should do Use only gualified service personnel to perform 981158 09JUL98 all necessary adjustments and procedures 21 0m3041_1_09jul98 doc Printed In USA Kodak and X Omat are trademarks HEALTH IMAGING EASTMAN KODAK COMPANY e ROCHESTER N Y 14650 Ka
15. g the Crossover Assemblies be careful not to twist them out of square or disturb the settings of the Guide Shoes e Use a synthetic sponge and warm water Do not use any abrasive material on the Racks Crossover Assemblies or Squeegee Rollers Do not rinse the Detector Crossover Assembly or the Dryer Assembly 5 Remove the Evaporation Covers and the Crossover Assemblies a Rinse the Evaporation Covers b Rinse the developer fixer and fixer wash Crossover Assemblies in warm water 6 Rotate and clean the Rollers with a soft brush and warm water 7 Dry the Rollers with a damp cloth or synthetic sponge 8 Wipe off all chemical deposits above the solution level in the processing section 9 Remove the Dryer Assembly 10 Clean off debris or buildup from the dryer area and Dryer Assembly with a warm damp sponge or cloth Use only qualified service personnel to perform 16 all necessary adjustments and procedures 09JUL98 981158 Figure 14 Silver Recovery Unit BYPASS at Pa nl 3 H112_0007ACA SILVER RECOVERY UNIT H112_0007AC Figure 15 Rack and Turnaround Assembly STUD A TURNAROUND SY H112_0018AcB SIDE PLATE 2 H112_0018AC Cleanup and Periodic Maintenance Caution e Fixer will contaminate the developer When removing the Rack Assemblies use the Splash Guard between th
16. he correct Tanks Seat them firmly L gt Note The washer on the top of the drive side of the Developer Rack has a D on it The Fixer Rack has an F The Racks may also have red blue and white wire ties for easy identification red for the Developer Rack blue for the Fixer Rack white for the Wash Rack 8 Install the Crossover Assemblies the Dryer Assembly and the Evaporation Covers 9 Allow the developer to reach the operating temperature before processing any film Use only qualified service personnel to perform 10 all necessary adjustments and procedures 09JUL98 981158 Replenishment Section 4 Replenishment Checking the Replenishment Flow Rates Figure 10 Checking the Replenishment Flow Rates 1 Remove the Top Cover DEVELOPER TUBING QUICK 2 Lift the Upper Roller of the Detector Crossover METAL DISCONNECT Assembly LATCH 3 Check that the replenisher solutions flow freely GRADUATED through the tubing located along the drive side of CYLINDER the Racks FIXER TUBING 4 Disconnect the Developer Tubing by pressing the Metal Latch gt Note The Developer Tubing may have a red wire tie on it for easy identification 5 Pull the Developer Tubing slightly and rotate it over the edge of the frame and into a Graduate 6 Lift the Upper Roller of the Detector Crossover Assembly for the correct time 28 or 34 seconds See the table on the next page H112_0114ACA H
17. n AAA SR AN BEN RN AN 8 Draining the Tanks isss yen So sen ea mana 9 Pilling th Tanks sea in san Dona Hbd da bie RES ae eat 10 Replenishment et Manna ena ana En BnR UPN dsb arene Spa aeons 11 Checking the Replenishment Flow Rates eee eee 11 Correcting Difficulties ii 13 Cleanup and Periodic Maintenance ii 15 Daily sonar set deta sbatea mann asa agan Sunan busana Sowa 15 Every Two Weeks entot na NS uan Ban REA NN en 16 Special Maintenance for Low or High Volume Usage 19 New Equipment Warranty ii 21 Warranty Coverage mana nae doe ote coe eee una dan an eee ew 21 How to Obtain Service 0 0 ee cette eee eee 21 EAMMtA ONS aa ten elsa atta a Re ea ee OE a BT Bee EA i 21 2 09JUL98 981158 Overview Section 1 Overview Description The KODAK M35 and M35A X OMAT Processors are designed to process medical x ray sheet or roll film that can be processed in KODAK RP X OMAT Developer Replenisher and in KODAK RP X OMAT Fixer and Replenisher This self threading roller transport system has a film length detection system a replenishment system a developer solution filter a recirculation system for the developer and fixer solutions an automatic standby feature The transport speed is 30 inches per minute or 2 minutes and 20 seconds drop time dry to dry for a 24 cm sheet of film The developer temperature is the standard 33 3 C
18. onnel to perform all necessary adjustments and procedures 13 OPERATOR MANUAL 1 Transport Failure 2 Surface Artifacts 3 Abnormal Film Densities 4 Wet Films 5 Low Solution Levels 6 Overlapping of Films Check that the Turnaround Assembly is adjusted correctly Make sure that the Turnaround Assemblies are square with the Racks Check the incoming water temperature Temperature must be between 4 4 C 40 F and 29 4 C 85 F Check that the correct Bulb and Safelight Filter are in the Safelight and at the correct distance from the Feed Shelf and work surface Check that the Top Cover and Panels are tight on the Processor Check that there are no leaks in the Lighttight Gasket 10 x 10 cm films feed films diagonally if they fail to transport reliably Check the time delay For all transport speeds the buzzer should sound once the trailing edge of the film has advanced 75 mm 3 in into the Processor e Check that the tank solution levels are at the overflow Weirs Adjust the Guide Shoes correctly NOTE Most often in the Developer Turnaround Adjust the long edges of the guide shoes in the exit turnaround as close as possible to the rack roller above them Check for solution in the Replenishment Tanks Fill if necessary NOTE Mix developer replenisher in guantities not to exceed a 2 week supply With a thermometer of known accuracy check that the
19. orking hours Such repair service will include any necessary adjustments and or replacement of parts necessary to maintain your equipment in good working order How to Obtain Service Should equipment require service refer to the sales contract for details on whom to call for service or contact the dealer for KODAK X OMAT Processors who sold the equipment Limitations e Warranty service is limited to the contiguous United States the island of Oahu in Hawaii and certain areas of Alaska e This warranty does not cover circumstances beyond Kodak s control misuse abuse any attachments accessories or alterations not marketed by Kodak including service or parts to correct problems resulting from the use of such attachments accessories or alterations failure to follow Kodak s operating instructions or supply items e Kodak makes no other warranties express implied or of merchantability for this equipment Repair without charge is Kodak s and the dealer s only obligation under this warranty Kodak will not be responsible for any consequential or incidental damages resulting from the sale use or improper functioning of this equipment even if loss or damage is caused by the negligence or other fault of Kodak Such damages for which Kodak will not be responsible include but are not limited to loss of revenue or profit downtime costs loss of use of the equipment cost of any substitute equipment facilities or s
20. r 1 Turn on the water supply and the Main Power Switch 2 Remove the Top Cover 3 Check the following are seated correctly See Figure 4 e Developer Rack e Fixer Rack e Wash Rack Fixer Wash Crossover Assembly Developer Fixer Crossover Assembly Detector Crossover Assembly Dryer Assembly 4 Check e the developer fixer and wash solutions are at the overflow level of the Weirs e water is flowing from the Water Inlet Tube of the Wash Tank e the Evaporation Covers are installed Use only qualified service personnel to perform 4 all necessary adjustments and procedures 09JUL98 981158 Processing Film Figure 4 Racks and Crossovers FIXER WASH CROSSOVER ASSEMBLY DEVELOPER FIXER CROSSOVER ASSEMBLY DRYER ASSEMBLY t ii ji Po rat a WASH h L RACK F lt E Ash 1 F 2 STT NG Hi H iu a L z Ez O oo TT Fal 1 o u HE O malm T wmm mjr aT ET n IL Ee uu uh n UI Ha H o D TSS ooo 2 BA FIXER RACK DEVELOPER RACK DETECTOR FEED SHELF CRO
21. ttings are correct Adjust the Dryer temperature control setting to the lowest possible temperature that still allows good drying Clean the Feed Shelf and Detector Rollers Clean any biological growth in the Wash Tank with a mild solution of chlorine bleach Use 60 mL 2 fl oz of bleach per 3 8 L 1 gallon of water Wipe the Tanks with a soft sponge Check that the Weirs are seated correctly Check that the Tanks are full Change any chemicals that were not mixed correctly are exhausted or are contaminated Check that replenishment flow rates are correctly set Fill the Replenishment Tanks if necessary Check that all Rollers are in place and positioned and rotating correctly Check that all Roller Gears Sprockets and Idlers are engaged Replace any Roller that has a broken or worn Gudgeons Replace any Bearings that do not allow the Turnaround Rollers to rotate correctly Check the tension on the Rack Chain Check that the Rollers do not hesitate and that the Chain moves smoothly With the Processor on check for movement on the surface of the solutions Movement indicates recirculation If the incoming wash water is dirty clean the Rack and Tank thoroughly Change the incoming water Filter Make sure to use the correct water Filter Check that the Dryer Air Exhaust is free from any obstruction 981158 09JUL98 Use only qualified service pers

Download Pdf Manuals

image

Related Search

Related Contents

TP301DTM – Device Type Manager  Netgear WAB102 User Guide  Conserver Flowmeter User Manual  Règlement du jeu - total raffinage marketing  BEDIENUNGSANLEITUNG NORDAC vector mc Frequenzumrichter  a PDF Product Sheet  Istruzione d`uso  取扱説明書・ 承認図  Cotek SK200 & SK350 Manual  Compressed Earth Brick Press: User Manual  

Copyright © All rights reserved.
Failed to retrieve file