User Manual - SkylinkNet Alarm System
Contents
1. Allstar transmitter or LOM oo on 7 RT learn the keypads code First open the battery compartment receiver has fewer than 9 Stanley 1976 1997 Position 1 to 10 OR 11 amp 12 setto vor remove the battery isolator the plastic strip between the two switches and the existing n Multi Code 1982 1997 Position 1 to 10 OR 11 amp 12 set to or batteries replace the battery cover Press the learn button on transmitter has 2 buttons Chamberlain 1983 1997 Position 1 to 9 0 center OR the garage door opener unit with motor located in the ceiling see diagram C then the Lift Master 1983 1997 Position 1 to 9 0 center OR fth f imately t d that the light Sears 1983 1997 Position 1 to 9 0 center OR of the garage for approximately two seconds so that the lig button that operates the Wayne Dalton 1983 1997 Position 1 to 9 0 center OR beside the learn button goes on While the light is on enter the receiver will determine how Master Mechanic 1983 1997 Position 1 to 9 0 center OR 4 digit pin number currently set at 0000 then press the SEND to set the number 9 DIP q P Genie 9 positions 1983 1997 Position 1 to 9 OR key If the light beside the learn button flashes the operator has switch of the model 88 If Genie 12 positions 1983 1997 Position 1 to 12 OR nalei b d Master Craft 1985 1997 Position 1 to 12 OR now learned and will rec2. PROGRAMMING THE TRANSMITTER Thank you for your purchase of the Skylink garage door remote control Model 88 There are 3 different things you need to setup in order to use this universal garage door remote control to operate your existing garage door opener These 3 things are 1 Frequency switch select the correct frequency accord ing to the brand of your existing garage door opener 2 Brand jumper place the brand jumper at the correct position according to the brand of your existing garage door opener 3 Code setting Set the DIP switches on the Model 88 so that they match the code setting of your existing garage door opener Please follow the detail instructions below in order to set 1 up the Skylink Model 88 to work with your existing opener Open the front cover and slide open the battery compartment Remove the battery isolator the plastic strip between the two batteries then re place the battery cover battery Isolator SET BRAND JUMPER SET FREQUENCY SWITCH 2 To Program Your 3 Set brand jumper by moving Frequency 4 Set frequency switch located above the Keypad the red plastic tab to the correct Switch ABCD to the corresponding letter Open the cover jumper see diagram and chart USA CANADA j Set switch Set switch on the back below Slide an opened paper Brand of your
3. e light beside the learn button flashes the operator has now learned and will recognize the keypads code lf your Pulsar Allister Allstar ADX9921 has 2 position Dip switches refer to the chart below If any of the Dip switches in your Pulsar Allister Allstar switches in the model 88 to the 88 to the position If the Dip switches 5 9 on the Pulsar Allister Allstar are set to the ON position set the position see Diagram transmitter receiver are set to the OFF position set A and B the switches in the model 88 to the o position lf Dip DIP switch setting to match with Pulsar Allister Allstar transmitter switches 1 4 on the Pulsar Allister Allstar are PULSAR ALLISTER ALLSTAR MODEL 88 set to the ON position set the switches in the model DIP switch position setting DIP switch position setting Examples of how to set Model 88 l ON Ork L KORO 2 ON OFF 2 ORO Existing Transmitter 3 ON OFF 3 OR0 Model 88 4 ON OFF 4 ORO 5 ON OFF 5 ORO 6 ON OFF 6 ORO 7 ON OFF 7 ORO 8 ON OFF 8 ORO 9 ON OFF 9 ORO Diagram A Diagram B SET DIP SWITCHES DIP switch setting to match your opener 7 If your Pulsar Allister lf your existing opener does not have any switches then it can
4. f this keypad has 3 positions 0 If the switches of your existing receiver Stanley Genie Multi Code Linear Moore O Matic Martec Skylink have only two positions set the switches of the model 88 to for ON and for OFF or OPEN Do not use 0 center position If the switches of your existing transmitter Chamberlain Sears DIP Switch Location 7 8 9 Lift Master Wayne Dalton Pulsar or Master Mechanic have 3 positions set the dip switches of the model 88 to 4 5 i Hoa e J e e Ld Qo o 0 ojo 6 match their corresponding positions switches than this transmitter match only the first corresponding DIP switches Leave the remaining DIP switches at 0 or the center position If your garage door opener is a Stanley or Multi Code the unused DIP switches may need to be set to either the or the posi tion If the transmitter is still not working try reversing the set Dip switches example if the 1 DIP switch is set to change it to and continue reversing the remaining DIP switches Also try the unused DIP switches in the 0 or positions SET DIP SWITCHES If your Stanley Multi Code receiver has fewer than 10 switches and you have a 2 button transmitter then the button that operates the receiver will determi
5. ing insert screw above the keypad in the slot provided a Remove the battery cover and insert the second screw in the lower slot b PIN press enternew PIN again press For example if you are changing the PIN number from 0000 to 1234 enter the following sequence 0000 1234 1234 bright outside When any key is pressed the next key must be pressed within 5 seconds or the backlight turns off and the sequence is canceled You must begin again digit PIN and the SEND key If confirmed the model 86 will emit three DO NOT let children use beeps the garage door tran smitter without adult supervision Children can injure themselves or If the keypad does not emit a beep when pressed wait a few seconds and press the key again If you hear a beep the keypad has accepted that Replace the battery key If confirmed the backlit others by the garage cover and insert LED flashes and the unit door screw Cc emits a long beep E E Skylink will not be held N If within one year from date Two 3 volt Lithium type WARNING The Universal Garage Door WARNING liable or responsible for WIRELESS of purchase this product CR2032 batteries included If the battery is completely Remote Control is approved Changes or modifications any misuse or application KEYLESS ENTRY should become defective drained or if it is disconnected by the FCC and it complies to this unit not expressly of this product o
6. ne whether you use Channel 1 or Channel 2 If the number 10 Dip switch of your existing transmitter is set in the OPEN or OFF position you have Channel 1 set the number 10 DIP switch in the model 88 to position If the number 10 Dip switch of your transmitter is set in the CLOSED or ON position you have Channel 2 set the num ber 10 DIP switch in the model 88 to position If your Sears Cham berlain or Lift Master transmitter has three buttons two small one large then the button that operates the receiver will determine how to set the number 1 DIP switch of the Skylink transmitter If the large button is used to operate the unit set the 1 DIP switch to position if the middle button is used set the 1 DIP switch to the center position if the button at the end is used set the 1 DIP switch to position Set the other DIP switches DIP switch 2 onward to match the setting of your existing transmitter Note LEARN CODE Some transmitters receivers do not have DIP switches this means they can learn new code settings Just set the DIP switches on our transmitter to any code combination Press the learn button located on the back of the garage door receiver located in the ceiling of the garage for 2 seconds then release so that the light beside the learn button goes on While the light is on enter the 4 digit pin number currently set at 0000 then press the key If th
7. ognize the keypads code the left button is usea to Martec Teckey 1992 2001 Position 1 to 10 OR 11 amp 12 set to operate the receiver set the Pulsar Allister Allstar 1985 2001 Position 1 to 9 0 center OR 5 9 DIP switch to posi Diagram C Skylink 1993 2001 Position 1 to 8 0 center OR 1 5 set or 0 Opener GDO tion if the right button is oe set to 0 used set the 9 DIP switch i a If your Skylink Universal Remote Control does not activate your Garage Door Opener GDO the reason to 0 position may be that your GDO age or manufacturer is not listed on the compatibility chart The solution is the Skylink UR 100 Universal Receiver or the 838 The Code Scrambler convert any GDO to a Total Security System For more information call 800 304 1187 aaa Button INSTALLATION KEY PAD OPERATION If this transmitter triggers Installation 9 Key Pad Operation To change your PIN Operation P EEES i Position the keypad NOTE The backlight comes on and a beepis Enter the current PIN Press PIN SEND pea arava on the garage door tlv set at0000 your neighborhood emited when any key is pressed The backlight currently set a To open or close garage change all your trans frame of the key pad may not be visible when it is too press enter new 4 digit door press your four mitters and receiver to a Lift up the cover and new code sett
8. opener to position Frequency to position Frequency clip into the top of the red plas Stanley 1976 1997 AorB 300 310 A 310 j i iti Multi Code 1976 1997 AorB 300 310 A 310 5 tic tab then lift and reposition MartecTeckey 1992 2001 l n j Skylink 1993 2001 AorB 300 310 A 310 CLOSE Brana Pe vot opener Vee AMan Number a ee B 310 A 310 Ter i M O M 1983 1997 B 310 A 310 Stanley 2 Master Craft 1985 1997 BorD 315 390 Multi Code 2 Pulsar Allister Allstar 1985 2001 C 318 C 318 Chamberlain 3 Chamberlain 1983 1997 D 390 BorD 315 390 OPEN Lit Mastar 3 l Lift Master 1983 1997 D 390 BorD 315 390 ae ay aues 3 DIP Switch Location Sears 1983 1997 D 390 BorD 315 390 He ee a E O Wayne Dalton 1983 1997 AorD 300 390 BorD 315 390 O Genie 9 positions 4 meme Master Mechanic 1983 1997 D 390 BorD 315 390 Genie 12 positions 5 Genie 9 positions 1983 1997 D 390 BorD 315 390 Master Craft 5 Genie 12 positions 1983 1997 D 390 BorD 315 390 Martec 6 Unknown Unknown Unknown syne ee Works with Skylink s Universal Receiver UR 100 SET DIP SWITCHES Brand Jumper 5 Opener Has DIP Switches 6 If your existing transmitter has fewer DIP Use a pen to set the DIP switches to match the code of your existing transmitter or receiver If your opener is a Chamberlain Lift Master Sears Wayne Dalton or Master Mechanic and does not have any DIP switches go to point 6 Each dip switch o
9. ther than USER S INSTRUCTIONS except battery due to longer than 1 week the PIN with Part 15 of the FCC approved by the party res for its intended use Model 88 faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase is required Battery Compartment It is time to change the bat teries when the backlight no longer appears you have set WILL revert to the factory preset of 0000 To preserve your PIN and reduce the chance of someone using PIN 0000 for unauthorized entry be sure to check and replace the battery regularly When replacing the battery check your PIN and reset it if needed Rules Its operation is subject to the following two conditions 1 This device may not cause harmful inter ference 2 This device must accept any interference that may cause undesired operation ponsible of compliance could void the user s authority to operate the equipment SKYLINK TECHNOLOGIES INC 2213 Dunwin Drive Mississauga Ontario L5L 1X1 CANADA 905 608 9223 905 608 8744 FAX Customer Service 800 304 1187 http www skylinkhome com P N 101A069 006 Rev 6 Patent no 5680134 Patents Pending 1995 SKYLINK TECHNOLOGIES INC are registered trademarks of their respective corporations
Download Pdf Manuals
Related Search