User Manual
Contents
1. The fluorescent lamp s electromagnetic field cause color roll This is proper AREA SEL AREA1 8 a on pane g pap CAUTION TO PREVENT ELECTRIC SHOCKS AND RISK OF PRIVACY AREA STATE OFF ON p l FIRE HAZARDS DO NOT USE OTHER THAN OFF ON Reduce the fluorescent lamp numbers or increase the distance between the SPECIFIED POWER SOURCE HEIGHT WIDTH LEFT RIGHT TOP BOTTOM COLOR camera and the fluorescent lamps can improve it PARK LIN Use power supply external sync camera can solve it OFF ON LT LB RT RB F N T V 1 V2 V3 SPE LENS SHAD OFF ON CIAL 2DNR OFF ON MIRROR OFF ON Note FONT COLOR FONT 0 15 ID amp TITLE 0 15 CONTRAST 0 255 SHARPNESS 0 31 NEG IMAGE OFF AN Please note the camera s operating temperature and its using ON Notes environment requirement Avoid using the camera at too high or too low temperatures The operating temperature is 30 60 C Recommendatory operating temperature is 10 50 C Never make the camera face the sun or bright object Other wise it will damage the CCD Do not mount the camera near by the radiator or heater 4 The picture smear too mass The power supply s voltage unstable Connecting cables not connect correctly or have high impedance DISPLAY CRT PED LEVEL 0 63 COLOR GAIN 0 255 LCD GAMMA 0 1 PED LEVEL 0 63 COLOR 0 255 The power supply must through safe attestation Its output voltage USER GAMMA 0 1 PED LEVEL 0 63 COLOR 0 255 current volt2. age polarity and operating temperature must match the camera s requirement When using the camera in the thunderbolt condition please note to mount Anti thunder device or put off the power supply plug and cable COMM CAM ID 0 255 BAUD RATE PROTOCOL DISPLAY ID ADJ ID POS LAN CHINESE ENGLISH ESPANYOL PYCCKNN DEUTSCH l Sa GUAGE PORTUGUES FRANCAIS JAP in order to capture high quality pictures the power supply s cable and FACTORY RESET video output cable should not be too long
3. m Specification c EET MCP650 Color Camera Pick up Element 1 3 SONY Super HAD CCD II SUSHI a BOONE NTSC 768 H x494 V PAL 752 H x582 V Horizontal Resolution 650 TV Line Minimum Illumination 0 001 Lux F1 2 S N Ratio More than 52dB P EN Talos Miniature Color Camera Synchronous System Internal Negative sync Auto Electronic Shutter NTSC 1 60s 1 100 000s PAL 1 50s 1 100 000s Gama Characteristic 0 45 Video Output 1Vpp 750 Auto Gain Control Auto Power Current DC12V 10 150mA Lens 3 7mm Taper Pinhole Lens Dimension mm 30 W x19 H x30 D Weight g 150 Storage Temperature 30 60 C RH95 MAX Operating Temperature 10 50 C RH95 MAX Notes Before providing power for the camera please read this User Guide in detail E Packing List Franchiser Do not attempt to disassemble the camera If the camera can not work please contact No Name Model ERT local franchiser or our company 7 Miniature Color Camera MCP650 1 2 User Guide MCP650 1 OSOReeeECE REO COe er erre eer reer errr err re rere rerr errr rer rre reer rer rrr rere rere rr rere rr rrr errr rr er errr errr reer reer rere rer rrr srr rre rer rr errr reer errr errr reece reer rere reer rere rere rere rere reece errr errr reer rere eer reece rere ee rere er rer errr reer reer errr reer reer errr reer reer errr errr errr rere errr reer rere errr rer rrr rr rrr reer errr errr errr reer reer errr ree rere reer reer rere rr rre cer rrr
4. mbol is intended to alert the user to the presence of OFF DC12V Power Supply ni ti d int important operating and maintenance servicing BACK BLC AREA SEL AREA STATE GAIN HEIGHT LEFT RIGHT TOP TROUBLE AND SOLUTION Instructions in the literature accompanying the appliance LIGHT BOTTOM a The symbol is intended to alert the user to the presence of coon l withi BURST OFF ON IR SMART OFF ON IR GAIN HEIGHT 1 No Picture after providing power uninsulated dangerous voltage within the product s DAY amp B W WIDTH LEFT RIGHT TOP BOTTOM IR LEVEL HIGH May be the power supply voltage abnormity please check the power enclosure that may be of sufficient Magnitude to constitute D N LEVEL DELAY N D LEVEL DELAY Please check all the connecting cable and monitors whether be connected _ correctly or not DPC CAUTION DPC COVER THE LENS THEN PRESS ENTER KRY a CAM 2 The picture level direction have flowing interference ripples RISK OF ELECTRIC DO NOT OPEN TITLE ON OFF May be caused by the power supply AC ripples it need filter the wave of the AREA LARENA power supply CAUTION TO REDUCE THE RISK OF ELECTRIC MOTION AREA STATE OFF ON i Check the monitor and peripheral equipments used DO NOT REMOVE COVER OR BACK NO USER OFF ON HEIGHT WIDTH LEFT RIGHT TOP BOTTOM DEGREE l l SERVICEABLE PARTS INSIDE REFER SERVICING VIEW 3 The picture background color changes continuously
5. rrr rre cer errr errr eer rere errr reer rere rere errr r errr reer errr errr reer errr errr rere errr errr reer rere rere rr rere errr reer rire rr rrr errr errr errr errr ere rere reer errr reer reer errr r rrr E BRIEF OF PRODUCT E CONNECTING E INTRODUCTION Congratulations on your purchase of this product This User Guide suits MCP650 product We adopt the latest SONY technical of sensor and driver The most at tractive characteristics are small and easy hidden suits the elevator and corridor In addition it owns the charac ters of high definition and stability strong anti jamming rich and real color Fixing and using this model are con venient too It is very good for you to apply to your CCTV MCP650 system Please read this instruction manual carefully to en sure proper use of the product Sensor CCD Adopt SONY 1 3 CCD Sensor Auto Gain Control AGC Monitor Built in auto gain control AGC circuit The color camera can get high definition picture in low Lux condition Scanning Mode NTSC or PAL mode OSD SETTING LENS MANUAL DC VIDEO See AUTO FLK 1 50 1 250 1 500 1 2000 1 40000 Link wire rule mae 1 5000 1 10000 1 100000 Video a SURE AGC LOW MIDDLE HIGH OFF D WDR OFF ON LEVEL 0 63 WHITE ATW AWB AWC SET ANTI CRL MANUAL INDOOR BAL Power To prevent fire or shock hazarded Do not expose the unit Waming to rain or moisture OUTDOOR MANUAL Dd Ge The sy
Download Pdf Manuals
Related Search