E-Board Series 5 User Manual
Contents
1. proper size hole for the screw to be used the largest holes receive M8 screws smaller holes receive M6 screws NOTE User may want additional clearance for any other desired Mantel Box peripherals To find the height clearance adjustment that s right for user consider the following steps 1 On the backside of the Flat Screen locate the lowest mounting positions and measure from this position to the bottom of the Flat Screen Using this measurement add the 2 to 3 inches recommended as noted above Keep this Totaled Number 2 On the E Board be sure the Tilt Assembly is fully retracted leaned back reference Figure 2 on page 11 3 On the Universal Mounting Plate locate the mounting pattern that matches the Flat Screen mounting pattern and note the lowest mounting positions 4 Check the Totaled Number to see if adjustment of the Universal Mounting Plate is necessary If needed loosen the four 4 Universal Mounting Plate M8 Flat Head Screws with provided 5mm Allen wrench adjust the vertical position to the closest matching mounting position using the Totaled Number THIS STEP REQUIRES AT LEAST TWO PEOPLE Read the additional NOTES on next page before starting this step NOTE For convenience located in Widget Works Carton 14104 in Parts Bag C5 are two 2 M8 Threaded Studs Wing Nuts that can be used by removing the top two 2 M8 Flat Head Screws first and installing the two 2 M8 Threaded studs2. 0 pounds 11 STEP 9 Use your Flat Screen manufacturer s directions for picking up the Flat Screen Genily insert the Threaded Studs into the proper matching top mounting holes in the Universal Mounting Plate on the E Board as shown Figure 3 REQUIRES AT LEAST TWO PEOPLE CAUTION THIS STEP REQUIRES AT LEAST TWO PEOPLE With two people holding the Flat Screen in this position they can align the Treaded Studs into the correct mounting holes and then thread the two 2 corresponding Wing Nuts onto ends of the Threaded Studs to prevent the Flat Screen from sliding forward while securing proper screws Figure 3 STEP 10 Install two 2 proper sized Button Head Screws through the Universal Mounting Plate and into the lower Flat Screen wall mounting locations Once the two 2 lower Button Head Screws are started secure but not tighten with the appropriate Allen Wrench one at a time remove each top Wing Nut Threaded Stud replacing them with the proper sized Button Head Screw A person may need to lift up on the threaded stud side of the flat screen to relieve the screen weight to remove stud Be certain that all Button Head Screws for this Flat Screen mounting are now secured STEP 11 Consult the Flat Screen User Manual for connecting the power cord video cable and other cables as instructed Reference any additional peripheral user manual s for cords and cables at this time NOTE Additional power cord s video cable or other c
3. The UPS is a combination surge protection and battery backup The UPS has extra power outlets for any addition components you may want to install Please also know that the UPS has built in indicators that produce a beeping sound code Please reference the UPS instruction sheet for details on these codes The E Board Series 5 120 volt power plug when not plugged into a power receptacle should be protected with the provided plastic protective cover and kept off the floor Please remember the UPS has a battery Note the pinch point areas reference the two labels The Universal Mounting Plate for the Flat Screen has the VESA standard design and non standard patterns for fitting most Flat Screens There is a vertical adjustment for clearance between the Mantel Box and Flat Screen bottom if needed Finishing with the front side of the E Board Series 5 with the unit lowered to the half way position 1 Review the operating instructions for the E Board The raise and lower control buttons in black for vertical adjustment of the Flat Screen The tilt front and back control buttons in white for angular movements of the Flat Screen lf applicable review the Flat Screen manufactures owner s manual for more details Please note that four casters of the E Board Series 5 are locking and should be locked for safety reasons when using the E Board Series 5 Please note that the E Board Series 5 has a wireless handset it is impo
4. Widget Works LLC TM PATENTED Series 5 USER MANUAL Universal Mounting Plate e CONTENTS Tilt Assembly Tilt Actuator e Operating Instructions backside hid a ac e Safety Precautions niemi UPS CPU e Requirements p Power Supply Mounting Support e Features Benefits e Crate Contents S ii e Assembly Instructions pe e roubleshooting Cross Beam e User Walk Around ie Ureciaed e Limited Warranty Retracting as Extension Power Cord Vertical Actuator a Swivel Sub Frame Caster Assembly Please fully read this User Manual U S Patent No 7 640 866 carefully follow all Thank you for purchasing the E Board by Widget Works LLC Set up should take approximately 30 to 45 minutes If you should instructions and have any questions about the product or for technical support retain it for future please email service widgetworksusa com or call 864 621 1444 between the hours of 9 00am and 5 00pm EST reference Errors descriptive typographic or pictorial are subject to correction Specifications are subject to change without notice 14 10 28 Email service widgetworksusa com Series 5 LA31 RF Widget Works LLC This manual contains important safety warnings and cautions Please read and follow all instructions carefully during assembly and operation _of the E Board WARNING e The E Board Series 5 is designed to mount a Flat Screen with a weight not to exceed 250 pound
5. Wing Nuts This allows support for the Universal Mounting Plate before removing the two 2 bottom M8 Flat Head Screws making the Universal Mounting Plate adjustment easier NOTE Make sure to use the same four 4 tapped holes on the Tilt Assembly when adjusting the Universal Mounting Plate SPECIAL NOTES If the Universal Mounting Plate will not adjust high enough simply rotate the Universal Mounting Plate one hundred and eighty degrees 180 for new range of higher adjustments restart this Step at Item 3 Should the Universal Mounting Plate need to be lowered more than the allowed adjustments there is a provision to do this Locate the four 4 yellow covered setscrews on the Tilt Assembly Remove these setscrews with 4mm Allen wrench and place each of these setscrews into one of the current tapped holes Make sure these setscrews are flush with mating surface When finished you now have lowered the Universal Mounting Plate adjustments approximately two 2 inches restart this Step at Item 3 5 Once the Universal Mounting Plate is re located be certain that all four 4 M8 Flat Head Screws for the Universal Mount Plate are secured STEP 6 Once again located in Parts Bag C5 is the following Threaded Studs Wing Nuts Button Head Screws and Allen Wrenches these are provided for mounting the Flat Screen to the E Board NOTE Again your Flat Screen User Manual will also give you the Flat Screen mounting pattern and screw
6. ables with extra length can be stowed in the Cross Beam s open cavities LZ STEP 12 Plug in the power cord from the Flat Screen into the surge protected only side of the UPS STEP 13 Figure 4 references the UPS CPU Mounting Support from the back side and also the Electronics Support located to the left The UPS CPU Mounting Support has a horizontal area to the left for mounting a desktop CPU The vertical surfaces have mounting patterns with fasteners for mounting a compact CPU two locations and on the horizontal surface of the Electronic Support for mounting a wireless gateway Figure 4 NOTE There is a vertical cut out on the back left side of the Cross Beam to stow the AC Adapter for the compact CPU Again any extra length of the cable and cord can be stowed in the Cross Beam STEP 14 Plug the CPU power cord into the battery back up side of the UPS If peripherals have been added plug related power cords into the appropriate side of UPS STEP 15 Plug video cable and all other user peripherals into the CPU and Flat Screen STEP 16 It is recommended at this point to do a start up Turn on all the equipment The Flat screen may need to be set to a particular Picture Setting and or other settings for specific needs Reference the appropriate user manual for any issue s An IT person may be helpful for additional software applications 13 STEP 17 The E Board assembly is now finished We recommend reading the E Boar
7. b Frame Assembly plug in the extension cord Plug the extension cord into a power outlet and turn on the UPS unit The E Board Series 5 now has power CAUTION The following safety options should be considered when children are using this device or are in the area during its usage This is not a toy as covered earlier in the Safety Warnings Option 1 Located under the Cross Beam reference cover photo on the left side looking from the backside of the E Board locate the Control Box the E Board power receptacle plug tagged with fluorescent yellow cable tie can be unplugged after the adjustments to the E Board Series 5 are made for the user This will stop power to the all actuators to ensure unaccompanied children may not operate the unit Option 2 At the Control Box is a receiver cable also tagged with fluorescent yellow cable tie for controlling the RF Wireless Handset which can also be unplugged this accomplishes the same purpose as Option 1 NOTE Both options may be utilized for additional safety precautions Before operating reference the E Board Series 5 Operating Instructions on page 3 CAUTION Before going to the next step make sure the E Board Series 5 is ona level surface and the four casters are locked WARNING The E Board Series 5 is designed to mount at Flat Screen with a weight not to exceed 250 pounds Total additional weights to E Board Series 5 including amenities in the Box Mantel are not
8. d Series 5 User Walk Around on page 16 to identify most of the design details that the E Board Series 5 has to offer NOTE Lastly there will be extra assembly items remaining due to Flat Screen variations we recommend keeping the extra items Screws Threaded Studs Spacers etc in a safe place along with the E Board Series 5 User Manual With the Universal Mounting Plate for Flat Screens and other designs built in to the E Board updating with new electronic components may be done with ease 14 Widget Works LLC TROUBLESHOOTING Uninterruptible Power Supply UPS e Beeping sounds coming from the UPS review the UPS User s Manual under the Definitions for Illuminated LED Indicators e UPS not performing see UPS Users Manual under Trouble Shooting Actuator Stoppage user cannot raise lower or tilt Flat Screen For RF Wireless Handset e The Wireless Handset is activated when assembling the E Board Please be aware that other equipment such as doorbells which use the same radio frequency can disturb the RF signal Should stoppage occur locate the RF Receiver a small plastic box mounted on the bottom side of the Cross Beam on the left hand side looking from the front side of the E Board Activate the reset key on the RF Receiver small opening on right side as follows Activate the reset key on the RF Receiver by using a pen or similar item to keep the button pressed Keeping the rese
9. he Flat Screen to its lowest level to ensure your safety CAUTION The E Board Series 5 120 volt power plug when not plugged in to a power receptacle should be protected with the provided plastic protective cover and kept off the floor Please remember the UPS has a battery e CAUTION The E Board Series 5 is not a toy and children should not be allowed to play with the actuator controls This unit has a wireless handset it is important to keep this out of reach when children are present See Step 2 in the Assembly Instructions for children safety considerations e CAUTION When moving the E Board Series 5 on a ramp special care should be taken so that the machine will be safely controlled at all times It is always recommended that at least two persons perform this operation e CAUTION The E Board Series 5 is not designed for outdoor use e CAUTION The E Board Series 5 is not designed for use around any type of water e CAUTION The E Board Series 2 is not design to be transported in any vehicle without being Widget Works LLC REQUIREMENTS Standard power specifications of 60 Hertz 50 Hertz if applicable For integration of computers with at least 128 MB video card and at least 1920x1080 resolution capability FEATURES BENEFITS RF Wireless Handset for actuator movements Height adjustments with Powered Vertical Movement from 28 through 55 at Box Mantel Beam Flat Screen with Powered Angular Tilt Movement with 15 fr
10. led a Works Carton S5 14 x 10 x 4 with the following v LN NN E Board User Manual RF Handset Parts Bag C5 for mounting Flat Screen Two 2 M6 Threaded Studs M6 x 50 mm long Two 2 M8 Threaded Studs M8 x 50 mm long Two 2 M6 Wing Nuts Two 2 M8 Wing Nuts Six 6 M6 Button Head Screws M6 x 16 mm long Six 6 M8 Button Head Screws M8 x 20 mm long One 1 2 5 mm Allen Wrench One 1 3 mm Allen Wrench One 1 4 mm Allen Wrench One 1 5 mm Allen Wrench One Lot Wire Ties 12 Strap Rip Tie All Purpose Strap Four 4 2 Center Labels 1 Wide x 36 Length Elastic Hook amp Loop Clinching Strap for Mini Computer HDMI Video Cable UPS Manual and Accessories Extension cord Widget Works LLC ASSEMBLY INSTRUCTIONS Before getting started fully read the Operating Instructions and the important m Safety Warnings STEP 1 STEP 2 STEP 3 Locate Widget Works Carton 14104 In this carton is the Uninterruptible Power Supply with battery backup UPS instruction sheet please take a moment to read Review your Voltage Amps VA and Watt W ratings for all the equipment that is going to be mounted to the E Board Series 5 to ensure the UPS is properly sized for the electrical loads Also located in Carton 14104 is an extension cord locate the E Board Series 5 common receptacle plug on the Su
11. ont tilt and 5 back tilt Engineered for ease of movement Foot print area Depth 33 x Width 43 not including Flat Screen Swivel Twin Wheel Casters allow for ease of mobility four wheel locking for increased stability Approximately 325 Lbs without flat screen and computer peripherals Integrated tubing electrical enclosures for cables and cords eliminating clutter Uninterruptible Power Supply UPS for surge protection and battery backup UPS CPU Mounting Support for power supply computer s and other peripherals a patented design feature allows for a single external power cord for operation Universal Mounting Plate for 50 to 90 Flat Screen with VESA MIS standard patterns provides vertical adjustment for clearance between Flat Screen and Box Mantel for user comfort Maximum Flat Screen weight 250 Ibs Stained wood storage box mantel for wireless handset user manual and flat screen devices Frame color Matt black on all surfaces Video Cable HDMI or Display Port User manual minimal assembly required includes fasteners and tools for mounting of Flat screen Standard power specifications of 60 Hertz 50 Hertz if applicable Controller for the actuators is programmable provides customizable height and tilt adjustments range control contact Widget Works LLC for details E Board Series 5 Limited Warranty for two 2 years from date of purchase Widget Works LLC E BOARD CONTENTS E Board Series 5 assemb
12. outside the permitted or intended uses as described by WWK c cosmetic damage including but not limited to scratches and dents that does not otherwise affect the Product s functionality or materially impair its use In no event will WK be liable whether as a result of breach of contract warranty tort including negligence or other grounds for special consequential incidental liquidated or punitive damages including but not limited to loss of profits or revenue loss of use of the Product cost of capital cost of substitute product facilities or services downtime costs or claims of customers of the user of the Product for such damages WARRANTY SERVICE EXCLUSIVE REMEDY WWK will be solely responsible for determining whether or not the Product is defective If a defect in the Product arises and a valid claim is received within the Warranty Period WWK will at its option either 1 repair or designate a service company to repair the defect at no charge using new refurbished or rebuilt replacement parts 2 replace the Product with Product that is new refurbished rebuilt or which has been manufactured from new or serviceable used parts and that is at least functionally equivalent to the original Product or 3 refund the purchase price of the Product upon its return WWK may request that you replace defective parts with user installable parts that WWK provides in fulfillment of its warranty obligation Repaired or replacement parts o
13. r Product will be covered by this Limited Warranty for the balance of the Warranty Period Defective Product and parts will become the property of WWK This paragraph states WWkK s sole and exclusive obligation and liability and your sole and exclusive remedy under this Limited Warranty WWK shall not be responsible for a failure to provide warranty services due to causes beyond WWK s control WWK shall not be responsible for related Flat Screens or Computers etc any Limited Warranty on those products or other accessories is provided by the related manufacturer WARRANTY CLAIMS Claims under this Limited Warranty must be reported to WWK during our normal business hours at the following number 864 621 1444 or by e mail at service widgetworksusa com or by contacting your authorized dealer distributor 17 Widget Works LLC NOTES
14. rtant to keep this out of reach when children are present See Step 2 in the Assembly Instructions for children safety considerations 16 Widget Works LLC E BOARD LIMITED WARRANTY LIMITED WARRANTY Widget Works LLC WWk warrants to you the purchaser that when operated and maintained according to instructions attached to or furnished with the E Board Product Product will be protected from defects in material and workmanship during the Warranty Period subject to the terms and conditions set forth herein The Warranty Period is two 2 years from the date the Product is purchased by the original purchaser THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF AND EXCLUDES ALL OTHER WRITEN OR ORAL WARRANTIES OR CONTRACTUAL AGREMENTS WHETHER EXPRESS OR IMPLIED BY LAW OR OTHERWISE INCLUDING IN THIS EXCLUSION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WARRANTY EXCLUSIONS WWK does not warrant that the Product will meet your specifications or needs You acknowledge that you are solely responsible for the selection of the Product and determining the suitability of the Product for your needs WWE is not responsible for damage arising from failure to follow instructions relating to the Product s use This Limited Warranty does not apply to a damage caused by accident alteration abuse misuse flood fire earthquake or other external causes b damage caused by operating the Product
15. s Total additional weights to E Board Series 5 including amenities in the Box Mantel are not to exceed 20 pounds CAUTION Read this E Board Series 5 User Manual the UPS Uninterruptible Power Supply Instructions amp Flat Screen Manual BEFORE PLUGGING IN this machine Take time to look over the machine to locate the labels marked Pinch Points and familiarize yourself and others with the controls BEFORE PLUGGING IN amp OPERATING this machine When placing next to a wall or other furniture allow at least a two 2 inch open buffer soace to prevent possible operational obstructions or pinch points The casters have locking mechanisms to prevent moving during use Please take a moment to locate labels marked Pinched Points and familiarize yourself and others with the controls before continuing Widget Works LLC E BOARD OPERATING INSTRUCTIONS RF WIRELESS HANDSET e The E Board Series 5 is controlled by a Radio Frequency RF Wireless Handset The Wireless Handset control button descriptions are as follows The top row in black on the RF Handset will Raise A and Lower v Flat Screen The bottom row in white on the RF Handset will Tilt Screen Forward v and Tilt Screen Back A CAUTION The E Board Series 5 Wireless Handset is not a toy and children should not be allowed to play with the actuator controls It is important to keep this out of reach when children are present See Step 2 in the Assembly In
16. size SPECIAL NOTE Should part of the flat screen mounting pattern go behind the UPS unit remove the Stop Lock round plastic knob mounted directly on top of the UPS Lifting up to remove the UPS unit move to the center area on the UPS CPU Mounting Plate and temporarily secure with furnished strapping Once the flat screen is mounted and secured re mount the UPS unit Re attach the Stop Lock making sure to rotate clockwise so that it is tight against UPS Make sure the Stop Lock fastener is secured STEP 7 Referencing information from both Steps 4 through 6 use the proper Threaded Studs Wing Nuts provided from Parts Bag C5 By hand screw in the two 2 Threaded Studs as far as possible into the two top vertical wall mounting locations in the back of Flat Screen as shown in photo Figure 1 Wall Mounting Locations Figure 1 CAUTION Before going to the next step make sure the E Board is on a level m surface and the four casters are locked 10 STEP 8 Be certain that the Tilt Assembly is retracted leaned back Figure 2 Use the RF Handset by pressing the white Tilt Screen Back button A referenced in the E Board Operating Instructions on page 3 to make this adjustment Figure 2 WARNING The E Board Series 5 is designed to mount a Flat Screen with a weight not to exceed 250 pounds Total addition weights to E Board Series 5 including amenities in the Box Mantel are not to exceed 2
17. structions for children safety considerations Widget Works LLC l E BOARD SAFETY PRECAUTIONS a e CAUTION The E Board Series 5 is designed to mount a Flat Screen with a weight not to e exceed 250 pounds Total addition weights to E Board Series 5 including amenities in the Box Mantel are not to exceed 20 pounds At no time should any person sit or lean on the E Board Series 5 e CAUTION When placing the E Board Series 5 near a wall or other furniture allow at least a two 2 inch open buffer space to prevent possible operational obstruction or pinch points The casters have locking mechanisms to prevent moving during use e CAUTION With the mounted Flat Screen check ceiling clearance water sprinkler heads and hanging light fixtures before operating E Board Series 5 If clearance is an issue the E Board series 5 controller is programmable to include limits on actuators Contact Widget Works for details e CAUTION Do not attempt to lift the E Board Series 5 with a Flat Screen mounted If lifting is required remove Flat Screen and lift from the Sub Frame only do not lift while gripping a hold of Box Mantel e CAUTION Take time to look over the E Board Series 5 to locate the labels marked Pinch Points and familiarize yourself and others about these locations e CAUTION The E Board Series 5 was not designed to be used on any raised platform incline or slope e CAUTION When moving the E Board Series 5 always lower t
18. t key activated the RF Handset must be activated by pressing any button on the RF Handset Upon activation of the RF Handset the reset key must be released For Actuators e Actuator stoppage is very unlikely Actuators are initialized at assembly and should not need further adjustment Should an unlikely stoppage occur the Controller must be reset as follows Vertical Movement Press the black Lower v Flat Screen button once or twice Then hold the button down until the actuator runs into the end stop position Release the button only when the movement has completely stopped Angular Tilt Movement Press the white Tilt Screen Back A button once or twice Then hold the button down until the actuator runs into the end stop position Release the button only when the movement has completely stopped Doing these steps will reset the Controller NOTE If the button is released before the sequence is complete then the initialization is interrupted and must be started again from the beginning Email service widgetworksusa com 15 Widget Works LLC E BOARD SERIES 5 USER WALK AROUND Starting with the back side of the E Board Series 5 with the unit raised to the highest position i Let s start by reviewing the power source the uninterruptible power supply UPS The retracting power cord connected to the UPS is the only cord leaving the E Board The UPS has its own power button
19. to exceed 20 pounds STEP 4 STEP 5 Read your Flat Screen User Manual before proceeding Use your Flat Screen manufacturer s directions for picking up the Flat Screen In preparation for the remaining steps review the Flat Screen User Manual s section related to vertical wall mounting Follow the manufacturer s steps for removing the stand from the Flat Screen if applicable For reference the Flat Screen User Manual will also give you the Flat Screen mounting pattern and screw size CAUTION For correct installing mounting and uninstalling of the Flat screen it is strongly recommended to use a trained person s with knowledge and experience in the vertical wall mounting of flat screens Failure to follow correct procedures may result in damage to the equipment or injury to the installer Flat Screen Universal Mounting Plate Preparations The Universal Mounting Plate has already been fastened to the Tilt Assembly at the lowest adjustment for shipping This plate has vertical adjustment increments to allow for clearance between the Mantel Box top surface and the bottom of the Flat screen It is recommended that you leave 2 to 3 inches of clearance to avoid possible pinching when the Flat Screen angular tilting adjustment is activated also keeping in mind clearance for the lid opening on the Mantel Box NOTE The Universal Mounting Plate has different size clearance holes for the different size screws to be used Choose the
Download Pdf Manuals
Related Search