Kip 7970 User Manual
Contents
1. ew ew Bw Bw e eB eB eB e la EF 1 Do not hold a thin wire to carry the entire tray 2 You cannot open Exit Cover until you move the tray from operation position to release position 3 Do not place any heavy object on the tray with mounted at release position 3 11 Chapter 3 Error Correction 4 Open Exit Cover Exit Cover A WARNING There are extremely hot parts inside the Heater Unit Do not touch any parts in the Heater Unit or you will be burnt Also the mis fed media can be very hot Be careful not to get burnt when you remove it 5 If it is possible to access the mis fed paper pull it out backward gently Be careful not to tear the mis fed paper If it is possible to access it close Exit Cover High Capacity Print Tray requires relocation See step 12 If itis not possible go to the next step 6 Open the Manual Table Manual Table 3 12 Chapter 3 Error Correction 7 Pull out the Upper Frame Unit to your side front with holding both handles Handle 9 Upper Frame Unit 8 Pull up both knobs and then push the Top Cover to rear side Top Cover Top Cover Top Cover 3 13 Chapter 3 Error Correction 9 Remove the mis fed paper 10 Close Top Cover Top Cover Manual Table Upper Frame Unit For the printer with High Capacity Print Tray go to step 12 on the next page for its relocation 3 14 Chapter 3 Error Correction2. 3 3 2 Toner Empty When the printer is running out of toner the Ul Screen will display Toner Empty sign For the toner cartridge replacement procedure refer to 2 4 Replacing Toner Cartridge 3 21 Chapter 3 Error Correction 3 4 Service Call Errors If an error with significant effect on the printer occurs the printer stops the operation and indicates a related Customer Engineer Call Error Code or description and its equivalent internal code on the UI screen Call the service staff immediately as these problems can be fixed by a well trained technician only Before calling the service staff try to turn on off the Printer If Service Call Error is indicated again turn off the machine unplug it and call the service staff with reporting the error description in the Ul screen Service Call Error Fusing Temperature Error Motor Error Developer Error Counter Error Cutter Error Toner Density Error High Voltage Power Supply Error Outer Device Error Wire Cleaning Error A corresponding description will be displayed in the top column status region in the Ul screen P uw COPY SCAN PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES J W MEDIA TONER Roll 1 Roll 2 Roll 3 Roll 4 e HH DIII 1 HH Se o ISO A0 ISO A1 ISO A2 ISO A3 Bond Bond Bond Bond 000o 3 22 Chapter 3 Error Correction DIGITAL PRINTER KIP 7970 Hardware Operation Guide Version A 1 Issued on April 15
3. KIP KIP 7970K User Manual Version A 1 SYSTEM SOFTWARE gt Thank you for purchasing the KIP 7970 This Hardware Operation Guide contains functional and operational explanations for the KIP 7970 Please read this Hardware Operation Guide carefully before using the Printer Please keep this Hardware Operation Guide for future reference 1 When this product is installed in North America This product complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This product may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the product Note This product has been tested and found to comply with the limits for a Class A digital equipment pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment This product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this product in a residential area is likely to cause harmful interference in which case the user will be required to corre
4. 12 Hold the thick wire parts of the tray and insert the hook parts at the lock position on the top face of the printer s rear beam Hold the wire s here Hold the wire s here Operation Position E Operation Position 1 Do not hold a thin wire to carry the entire tray 2 Ejected prints will be stacked incorrectly on Print Tray until you move it from release position to operation position 3 15 Chapter 3 Error Correction 13 Lift the Support Rod to the printer Fully slide the Lock Slide upward Slightly push the tray down to catch its bottom hooking part on the top of the Support Rod NOTE To fit the Lock Lever in position fully slide the Lock Slide upward Lock Lever not fit in 3 16 Chapter 3 Error Correction 3 1 5 Outer Device The printing paper is mis fed in the optional device such as Auto Stacker or Folder Remove the mis fed paper making reference to the User s Manual of concerning device 3 17 Chapter 3 Error Correction 3 2 Door Open When any deck cover is open not closed firmly the UI Screen will display Deck Open or any other prompt screen Close the concerning deck cover as it is impossible to print if this error exists 3 2 1 Roll Deck Deck 1 2 Open Deck Open will appear on the Ul screen when Upper Lower Roll Deck is open Completely push
5. 2015 Please note that some articles illustrations and photographs might be partially different from the actual machine because of the modification of machine and so on No part of this publication may be copied reproduced or distributed in any form without express written permission from K
6. The equipment must not be exposed to the air vents from air conditioners It may affect the image quality The equipment should not be exposed to the direct sunlight Please draw curtains to block any sunlight When you open the Upper Unit to remove a mis feed do not expose the Photoconductive Drum to strong intense light as this will damage the Drum Ozone will be generated while this equipment is use although the quantity generated is within safe levels See certifications Ventilate the room if required The site temperature range 10 to 32 degrees Centigrade with the humidity between 1596 to 8596 RH NON CONDENSING Keep the printer away from water sources boilers humidifiers or refrigerators Keep ample room around the equipment to ensure comfortable operation Refer to the following figure The equipment must be leveled and the floor strength must be ample to sustain the weight of the equipment Rear 800mm 32 or larger be S 1702mm 67 Right 300mm 12 or larger Front 800mm 32 or larger 1 2 Chapter 1 Before Use 1 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original You may be punished by the law if only you possess the copy of some kind of original We recommend you to consider enough before you copy such original Originals prohibited from copying by the law 1 It is not allowed to copy Currency Bill Money Bank Note
7. etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments 3 It is not allowed to copy unused postal stamps or government postcards without permission to make replica from Government 4 It is not allowed to copy Government issued revenue stamps certificate stamps which are prescribed by Liquor Tax Act or the Commodity Tax Act Special items to be cared 1 Itis warned by the government to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you not to copy freely such originals as government issued passport public or private issued licenses automobile inspection certification IDs and tickets like pass or meal Regulations to control fake currency and Currency Bill Money Bank Note etc Bond Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc Control Law against Forged amp faked Foreign Currency or Foreign Negotiable Foreign Currency Bill Bank Note and Bond Instruments Forged revenue stamps control law Government issued revenue stamps and certificate stamps prescribed by Liquor Tax Act or Commodity Tax Act Currency similarity securities Control Law Private issued secur
8. such as noise or flickering may occur Use a separate power line and install the PRINTER as far as possible from said equipment KIP 7970 is an ENERGY STAR qualified multifunction device oett The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations The symbol shown indicates that this product conforms to Directive 2012 19 EC of the European Parliament and the council of 4 July 2012 on waste electrical and electronic equipment WEEE and does not apply to countries outside of EU PESE Only For EU Member States The symbol shown indicates that this product conforms to SJ T 11364 2006 of People s Republic of China Electronic eS Gn Industry Standard and does not apply to countries outside of i 10 y People s Republic of China The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of China and does not apply to
9. RRR RRR RRR RRR RRR RER RRR ERRER ERRER ooo oon Appearance 0 00 0 0EZ0EZ0ES0S0S0S e 0Z0SLCSZ Z Z ZZZS 0 X 4 2 R r nn0EZEZ0EZ 0E4 O 0 0 0 0Z4 S4 5S 000E0E 0S0S000 0SSS 0S4 R pecifications for Printing Media NS TOR YVES Available Print Size sda eiie ees Dom d NSN TENTE TRER VIRAT EFIE E 2 TENE ues Men E A ba Heg ap Ygs Media not to be used P Maintaining Media ree ss Environmental Condition Z Correction E E FUR evi Ges E E Chapter 1 Before Use 1 1 Installation Requirements The following conditions are required for installation of the equipment A Left 50mm 2 or larger l 725mm 29 Printer 1 2 3 The outlet must be near the equipment and easily accessible Power source should be rated as follows 220V 240V plus 6 or minus 1096 50 60Hz 20A or higher The equipment must be on an exclusive circuit Make sure to connect this equipment to a grounded outlet 2 For PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible The installation site must not have open flames dust or ammonia gases 2
10. The joint will be latched on the right A NOTE olide the Joint until it clicks to unlock the toner cartridge Not doing so may damage the toner supply system 4 Pressing down the green lever rotate Toner Cartridge body not the Cap of Cartridge to the arrow direction until it stops This will close the toner supply opening on Toner Cartridge 5 Keep pressing the green lever Lift up Toner Cartridge and remove it A NOTE If your hand or your clothing is soiled by toner dust the toner If it is unable to dust it wash the clothing with the cold water Do not use the hot water at this time because the toner will soak into fiber 2 14 Chapter 2 Basic Operations 6 Peel off the wrap on the toner supply hole of Toner Cartridge Shake a new Toner Cartridge several times right and left to make the toner smooth 7 Press the green lever down until it clicks Insert the far left pin on Toner Cartridge into the slot firmly Please direct the opening on Toner Cartridge downward at this time A NOTE Please confirm that the green lever firmly locks the Toner Cartridge at the correct position It must be at a level position Correct Green Lever in position Wrong Toner Cartridge not locked 2 15 Chapter 2 Basic Operations 8 Slightly pull Toner Cartridge rightward and insert the swelling tab in the arrowed slot 9 Rotate Toner Cartridge to the arrow direction in 180 degrees or more The
11. To ee uus L oc O c c P an Qe 3 lt eo T o O ru c e Q 2 ug C g N Q D a S n c O c o 2o9 O0 G v Z x N D D Sc GL co O i o o Cx D ES m o Jaj 89 G S5 i 5x el n S a C O O T eL V K gt T CO Oc T gt Ss IL 5 Q X O o o D 2 op Q cr cC oO S Cc SO ja N O O gt QD QO D 4 Dog 2 x X o O o2 wx Qo C Z lm R Q d t O O Ke Ci DL c E po e Oo OQ e Ola Ss GO 2 cO c Oo S l Tl Or 2 I L LL Z Chapter 2 Basic Operations 2 21 2 With holding the extension tray slide it completely to the arrow direction For use of thin vellum tracing paper and film in D A1 portrait or E AO press the lever down In most sizes types the lever should remain up F mul E x This equipment is exclusive use of stacking ejected prints from the printer Please contact your local dealer for other outer devices Scanner Auto Stacker Folder etc See the device s documents if you use one That might include additional information for usage notice of the printer 2 22 Chapter 2 Basic Operations Chapter 3 Error Correction page 3 1 Paper Janm 250 3 1 1 Roll Deck Section Jam Deck 1 2 3 4 Mis feed TTT 3 3 3 1 2 Manual Feeder Section Jam By Pass Mis feed Registration Mis feed TTT TTT PNE 3 5 3 1 3 Media Feed Section Jam Mid Feed Mis feed Registration Mis feed Separation Mis feed 3 6 3 1 4 Fuser Section Jam Exit T
12. countries outside of People s Republic of China Safety Warning The following warnings are very important in order to safely use this product These notes are important in preventing danger to the operator or operation of the printer The following symbols are found throughout the USER S Manual and have the following meaning WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not follow the said instruction When marked with this symbol DO NOT ATTEMPT When marked with this symbol pay close attention to WARNING Ground the product with a correct ground source or you may be electrically shocked The Power source should be as follows 220 to 240V plus 6 or minus 1096 50 60Hz 20A or higher Use a circuit with a dedicated breaker Install the product as close to the wall outlet as possible If you wish to move the printer please contact your service personnel Do not remove the screw and do not open the cover if not instructed to do so in this User s Manual If you ignore this warning you may be burnt or receive an electric shock due to a hot item or electrically charged part inside of the printer Do not disassemble or tamper with the printer It may result in a fire or an electrical shock D
13. of inactivity in order to reduce the power supply for Fuser Unit e Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser Unit and some other components Sleep Mode is canceled and the machine gets ready when e the machine receives a print job through the network e an original is inserted into a KIP Scanner option e you tap on the UI screen NOTE 1 It may take time for the printer to get ready 2 Tapping on the Ul screen can cancel the screensaver but cannot recover temperature on Fuser Unit It may need another waiting time to start warming up for printing 2 18 Chapter 2 Basic Operations 2 Dehumidifying Roll Media If the roll paper is extremely humid it may cause poor prints You will experience most likely creasing and voids Normal Print Creasing If the media is humidified gt If the media is humidified _ gt A NOTE Re appearance of image especially solid black image may occur if you print with a humidified film When film is installed under the high humidity environment higher than 60 RH we also recommend that you turn on the Dehumidify Heater Re appeared image Normal print Turn on the Dehumidify Heater if the room air has too much humidity 65 or higher to prevent the above kinds of print defect You may be able to fix the above kinds of problem 2 19 Chapter 2 Basic Operations A NOTE 1
14. There are several dehumidifying settings which can be set by service personnel When these settings are determined the dehumidifier functions With any setting the printer must be plugged in and the switch noted above must be in the H position Call your service personnel if you would like to change the switch setting Note that the user can not change the setting 2 To achieve the best image quality we recommend that you use media that is unpacked from the manufacture right before installing it into the printer If media is unpacked long before installation poor image quality may occur Dehumidify Heater Switch is located on the left rear side of the machine Press H to turn on the Dehumidify Heater Press H side Dehumidify Heater Switch 2 20 Chapter 2 Basic Operations Prints on High Capacity Print Tray option 2 8 Stackin gt C LU 2 o c D TB x lt LLI CNN Y Y 7 JAN NJ NU Nb y IS N E sS gt C L S 2 A gt O Q OO O X D L ab Q CC AS O o B o o C V q O L o Q 2 c o o o C B q O gt O Q MS O xX O B o m O ab LU L O O ab C LL included in 1 print job and printed without any interruption achieved when all pages are gt Tu 5 o C S x v O 2 o d gt g o O c SG Oo 77 c o g n gt x gt O o C
15. aper Exit Door Open the Paper Exit Door when you remove the mis fed media 2 Dehumidify Heater Press H to turn on the Dehumidify Heater and press L to turn it Switch off Inlet Socket Connect the power cord here 2 It is possible to shut off supplying the AC power USB connector Connect the cable to this terminal for a KIP Scanner option USB2 0 max 5Vdc E Sor diesem the cable from a finishing device option D Sub Connector 9 pins max 12Vdc Small LAN Port MM the LAN Cable to connect i KIP m to the network Do not connect a telephone line 1 8 Chapter 1 Before Use 1 6 Optional Configurations You can combine the KIP 7970 Printer with optional outer devices KIP 7970 KIP Scanner KIP Scanner KIP 7970 KIP 7970 on network Scanner Controller KIP Scanner Other printers NM Workstation p TA Please contact your dealer for further information of integrating KIP 7970 to your network and other devices KIP 7970 1 9 Chapter 1 Before Use 1 7 Specifications for Printing Media 1 7 1 Available Print Size Available print size is as follows Minimum Maximum 117 297mm Roll j Width 5 5 210mm Cut Sheet SOC UAR 85 210mm om Length 8 5 210mm NOTE It is possible to print longer than 6 meters as an option Call your service personnel if you would like to print over 6 meters as the user can not change this setting in the printer If y
16. ar ejection this allows for front stacking An operator can choose either way according to the necessity e The KIP 7970 adopts 12 1 inch screen for the UI wider than 10 4 for our old products The capacitive multi touch screen offers smooth various and intuitive user operation that a pressure sensing device lacks 1 4 Chapter 1 Before Use 1 4 Specifications Print speed 160mm per second Inch e E 7 sheets min D Landscape 12 sheets min Metric AO 7 sheets min A1 Landscape 12 sheets min Print head Resolution Print width Maximum 36 914mm Minimum Roll 11 297mm Cut sheet Portrait 8 5 210mm Maximum Standard Print length 6 000mm bond 36 AO wide only or 5 x Standard length bond 2 x Standard length vellum 1 x Standard length film G Option 8 5 210mm NOTE If the print is longer than the maximum listed above its image quality or the reliability of paper feeding is not guaranteed Warm up time Less than 6 minutes 23 degrees Centigrade 60 RH and the rated voltage Bond First print time 15 5 seconds E A0 from Roll 1 Fusing method Development method Exposure method Charging method Transfer method Separation method Input power Power consumption Maximum 3600W or less Stand by 1300W Average Printing 2500W Average Conformity to International Energy Star Program 230V 50 60Hz and Dehumidify Heater is ON Acoustic noise less than 67d
17. b Printing less than 55db Standby Ozone less than 0 05ppm Average Dimensions 1370mm Width x 725mm Depth x 950mm Height w o UI 1702mm Width x 725mm Depth x 1377mm Height max w UI Weight Media Recommended Media US model Plain Paper 64g m to 80g m US Bond PB 20 Tracing Paper US Vellum XV 20 Film 4MIL PF 4DME Europe Asia model Plain Paper 64g m to 80g m Diamond Plain Paper 80g m Tracing Paper Gateway Tracing Paper 73g m Film NSFAMIL Film continued on the next page 1 5 Chapter 1 Before Use Environmental condition Temperature 10 to 32 degrees Centigrade for usage Humidity 15 to 8596 RH Interface Ethernet 10 BASE T 100 BASE TX 1000 Base T Serial port RS232 C USB 2 0 Storage of consumables Media Wrap the media surely to shut out the humidity Toner cartridge Keep the toner cartridge away from the direct sunlight and store it in the condition of 0 to 35 degrees Centigrade and 10 to 85 RH A NOTE The above specifications are subject to change without notice 1 6 Chapter 1 Before Use 1 5 Appearance 1 5 1 Front Name of part Function 1 User Interface UI This is a Touch Screen and many user operations are available CU MPH PLEASE DO NOT push the LOD sing oo Roll Decks Each Roll Deck drawer holds 2 rolls of print media Power Switch You can turn on off 1 7 Chapter 1 Before Use 1 5 2 Rear Name of part P
18. ct the interference at his own expense This product complies with Part 15 of FCC Rules and Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this product may not cause interference and 2 this product must accept any interference including interference that may cause undesired operation of this product Le pr sent appareil est conforme aux la partie 15 des r gles de la FCC et CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en comprometter le fonctionnement Contains FCC ID VP8 13551 Contains IC 73914 13551 2 When this product is installed in Europe This product complies with the requirements in Pub 22 of CISPR Rules for a Class A computing equipment Operation of this product in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install product around other electronic equipment or other precision instruments Other equipment may be effected by electrical noise during operation If the product is installed near other electronic equipment such as a TV or a radio interference to said equipment
19. d the UI look to be shut down when you turn off KIP 7970 However the embedded controller is still operating in approximately 2 minutes after Power Switch operation for the controller s shutdown Do not unplug the KIP 7970 before the controller s shutdown Doing so may damage data or the device 2 If you use Dehumidify Heater for Roll Decks the printer should be plugged while the printer is OFF Refer to 2 7 Dehumidifying Roll Media 2 4 Chapter 2 Basic Operations 2 3 Replacing Roll Media 1 When the printer is running out of a roll media the UI Screen will display Roll Replacement sign Follow the later procedure or as noted in the Ul s User Guide to load a roll media Please refer to your Touch Screen Operator s Guide for the UI screen 2 It is recommended that a tracing paper vellum roll is loaded to Roll Deck 3 or 4 Front lt L Rear 3 This section describes how to install a roll media to Roll Deck 1 The same procedure is applied to Roll Deck 2 3 4 unless otherwise noted 2 5 Chapter 2 Basic Operations 1 Open Roll Deck 1 Holding both Flanges 2 lift and remove a roll media or an empty roll core 3 2 Raise the green lever 4 on Flange 2 Remove both Flanges 2 from the roll core 3 3 Hold the shown part of the right Slide Guide 5 Move it to match your roll media s width The right and left Side Guides will automatically move together Hold here to
20. e Upper Frame Unit 3 Pull up both knobs and then push the Top Cover to rear side Top Cover Top Cover 3 7 Chapter 3 Error Correction 4 Remove the mis fed paper 5 Close Top Cover Top Cover 6 Close Upper Frame Unit and Manual Table Upper Frame Unit CP Manual Table 3 8 Chapter 3 Error Correction 3 1 4 Fuser Section Jam Exit Top Mis feed Exit Back Mis feed Fuser Section Exit Top Mis feed Exit Back Mis feed 1 It is necessary for a printer with High Capacity Print Tray option to move it aside to release position First remove stacked prints from the tray If your system does not have High Capacity Print Tray go to step 4 Prints High Capacity Print Tray Support Rod 3 9 Chapter 3 Error Correction 2 Flip up the Lock Lever on the top of the Support Rod olide the Lock Slide down to release the tray Tray side section Lock Lever Lock Slide Support Rod NOTE Please note that the tray may slightly bounce at the time of release 3 10 Chapter 3 Error Correction 3 With holding the thick wire s on the overlapping area of the tray lift up the entire tray Insert the hooks into the holes on the tray rest release position Hold the wire s here Hold the wire s here m m ma cm mm m c m o ma a a dl w p Operation Position i
21. ities stock draft check goods ticket etc commutation or book tickets Originals protected by the copyright It is prohibited to copy such originals as book music paintings printed copy maps drawings movie and pictures which are protected by the copyright except for personnel or family use or similar purpose 1 3 Chapter 1 Before Use 1 3 Features e KIP 7970 Digital Printer can make a print in a speed of 160mm per second The maximum print size is 36 inches 914mm wide and the minimum one is 8 5 inches 210mm for cut sheet media and 11 inches 294mm for roll media e he print image is more stabilized than before since we adopt a minute toner for mono component development e Density Compensation Process provides consistent image density in various environments e he KIP HDP Plus imaging system produces high definition lines distinctive greyscale and consistent blacks e Flange type loading mechanism eases operator s media loading work e When connected with an image scanner such as KIP2300 or KIP720 KIP7970 functions as multifunction printer e Easy access to USB port allows users to provide efficient productivity by using File to Print Scan to USB option e The following stacking options are available Auto Stacker About 200 prints Bond PPC can be stacked High Capacity Print Tray About 100 prints Bond PPC can be stacked Front Stacking Print Tray In addition to the conventional re
22. let of the installation location shall be conducted in accordance with the following N WARNING Select a power plug which meets the following criteria The plug has a voltage and current rating appropriate for the product s rating marked on its name plate The plug meets regulatory requirements for the area The plug is provided with a grounding pin or terminal If the appropriate plug does not fit the wall outlet in the installation the customer shall install an appropriate outlet Connector Type Usually found in IEC60320 C19 20A 250V UL 16A 250V IEC Usually found in NEMA6 20 20A 250V North America UL Listed AS NZS 3112 16A 250V Australia New Zealand GB1002 16A 250V China GB2099 1 Cord Type Usually found in SJT 3X12AWG Long lt 4 5m 20A 250V North America UL Listed HO5VV F 3X1 5mm 16A 250V European countries ii ds RVV 3X1 5mm 16A 250V Chapter 1 Before Use l 1 Installation Requirements PORNO DUCUM a CRM DM NUM RA NTC UE Re or a DESEE alar Ra TEI N 3 Features TE LOSS E E A E AS E A RO 1 1 S edd T2 Leo 1 4 1 1 Originals Prohibited from Duplication PTEE este ocak EET aaa eaa r R gpu LC peci ICa ions esen RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RRR RER RRR RER RRR RRR RRR
23. ll Deck Section Jam Deck 1 2 3 4 Mis feed Roll Deck Section Deck 1 Mis feed Deck 3 Mis feed BN Roll Deck Secllon Deck 2 Mis feed Deck 4 Mis feed dio Neds 1 Open the Roll Deck in issue And then rewind the roll onto the media core Roll Deck 2 f the leading edge of the media is torn or folded cut it off 3 3 Chapter 3 Error Correction 3 Set the roll media correctly Front Deck Roll 1 3 A NOTE The outside rim of Flange should meet the black triangle marked on Slide Guide Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding Correct 4 Close the Roll Deck 3 4 Chapter 3 Error Correction 3 1 2 Manual Feeder Section Jam By Pass Mis feed Registration Mis feed Manual Feeder Section By Pass Mis feed Registration Mis feed 1 Pull out the Mis feed paper from the Manual Feeder and if the leading edge of the paper is torn or folded replace it with a new one 3 5 Chapter 3 Error Correction 3 1 3 Media Feed Section Jam Mid Feed Mis feed Registration Mis feed Separation Mis feed Media Feed Section Registration Mis feed Media Feed Section Separation Mis feed Media Feed Section Mid Feed Mis feed 1 Open the Manual Table Manual Table 3 6 Chapter 3 Error Correction 2 Pull out the Upper Frame Unit to your side front with holding both handles Handl
24. new Toner Cartridge is closed firmly so as not to lose the toner during the transportation A NOTE Even if the Joint is not fit to the Toner Cartridge when you turn on the printer it is automatically fit properly Manual Table Upper Frame Unit 2 16 Chapter 2 Basic Operations 2 5 Placing Cut Sheet Media 1 Open Manual Table Manual Table 2 There are several size markings on Manual Table which indicate possible feed positions Place a cut sheet in a required size on the table between its concerning size markings then insert it into Manual Feeder When the leading edge touches the feeding roller the machine automatically carries and sets the sheet at the proper position A NOTE 1 As a curly cut sheet will cause a mis feed straighten the sheet as far as possible before printing And set the sheet in curl down direction as a mis feed can be avoided Curl up sheets tend to result in a mis feed Correct curl down Wrong curl up 2 Setting a cut sheet to the bypass feeder while printing may cause a paper jam Be sure to check the printer is idle not processing a print job before setting a cut sheet 2 17 Chapter 2 Basic Operations 2 6 Canceling Sleep Mode The KIP 7970 has two Sleep Modes to reduce the power consumption The KIP 7970 will enter Sleep Mode after a certain period of inactivity In the default setting e Warm Sleep Mode will start after a 15 minute
25. o not plug in the printer into a multi wire connector in which some other equipment is plugged into It may cause a fire due to outlet overheating Do not damage the Power Cord by stepping on or placing heavy items on it If the Power Cord is damaged it may cause a fire or you may receive an electric shock REPLACE THE CORD IF DAMAGED Do not put a flower vase a flowerpot or any water filled item on the product opilt water could cause a fire or an electric shock If the product generates an abnormal smell or noise turn it off and unplug it from the wall electrical outlet immediately Do not throw the toner into a fire or other sources of heat as it can explode CAUTION Do not install the printer in a humidified room or a dusty room Also do not install the printer on an unstable floor as injuries may occur 1 Unplug the printer before you move it The power cord may be damaged and it may result in a fire or electric shock If you do not use the printer for a long duration holidays company shutdown turn off and unplug the printer from the outlet for safety Do not pull the cord when you unplug the printer as you may damage the Power Cord There are hot items inside of the printer Take great care not to touch these items when you remove mis fed media Ventilate the room well if you print in a small area POWER CORD INSTRUCTION The installation of or exchange to a power plug which fits in the wall out
26. oll Deck fully until it locks at the correct position A paper jam may occur if it is not locked firmly 2 Be sure not to catch your finger in between Roll Deck drawers 2 11 Chapter 2 Basic Operations 10 When you close Roll Deck MEDIA screen will appear on the UI screen Choose the correct width and type and press Initial Cut button with scissors icon for the corresponding Roll Deck MEDIA Ready y Feeder 1 Feeder2 Feeder 3 CHUL Se iSMS le 1 TI Se Feeder 4 ASe 2 12 Chapter 2 Basic Operations 2 4 Replacing Toner Cartridge A WARNING There is combustible powder in the toner cartridge Do not burn up the used toner cartridge Reference When the toner is empty the UI Screen will display Toner Empty sign Follow the later procedure or as noted in the Ul s User Guide to replace the Toner Cartridge with a new one genuine NOTE 1 The KIP 7970 will indicate Toner Empty sign if an incorrect toner cartridge or no toner cartridge is installed to the printer 2 At the machine s installation some amount of initial toner powders will be supplied to the machine Thus Toner Empty sign might appear slightly earlier for the first installed toner cartridge than usual 1 Open the Manual Table Manual Table Upper Frame Unit ul 1 1 Pa 2 gt j i i F 2 13 Chapter 2 Basic Operations 3 Push the Joint rightward to release the Toner Cartridge
27. op Mis feed Exit Back Mis feed ai 3 9 3 1 5 Outer Device TTT TTT 3 17 3 2 Door Open T e NN MR CER 3 18 3 2 1 Roll Deck Deck 1 2 Open muse c AU ele c Ado SM Mt eai A telo ctu eot ahi A TENA A 3 18 3 2 2 Upper Frame Unit I Top Cover Front Cover Open GA a NATA EEN a ot 3 19 9 2 9 Paper Exit Door Paper Exit Door Open mu EE A DU RE E EN EE 3 20 3 3 Other Errors E E e A A eal 3 21 3 3 1 Roll Replacement cT mar eM DEREN 3 21 3 3 2 Toner Empty r w H cates 3 21 3 4 Service Call Errors c PPM ETE ERSTER ERPRTME 3 22 3 1 Chapter 3 Error Correction 3 1 Paper Jam Paper Jam is displayed in the Ul screen when the media is jammed The jammed location when displaying Paper Jam is shown below Manual Feeder Section Media Feed Section Fuser Section Roll Deck Section Roll Deck Section 1 Be careful not to get paper cuts on your hand 2 Gently remove a jammed paper When it does not reach Fuser Unit toner on it may spill off If toner gets into eyes or your mouth immediately rinse them with water and contact a doctor 3 Gently remove a jammed paper When it does not reach Fuser Unit toner on it may spill off on your cloth Dust off your cloth Use cold water to wash in out Using hot water may leave a stain 3 2 Chapter 3 Error Correction 3 1 1 Ro
28. or KIP 7970 into a dedicated wall outlet A WARNING 1 Do not handle the Power Plug with wet hands or you may receive an electrical shock 2 Ground the printer for safety 3 Do not plug the printer into a multi wiring connector in which other devices are plugged into It may overheat the outlet and may result in a fire 4 The OUTLET must satisfy the following rated power condition 220V to 240V plus 6 or minus 1096 50 60Hz 20A or higher 2 There is Power Switch on the right front of the printer Press side to turn on the printer Press this side O 2 2 Chapter 2 Basic Operations 3 The User Interface UI starts operating and displays Ul Screen in one minute Warming Up is displayed in the status indication while warming up Warming Up COPY IIT PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES Roll 1 Roll 2 Roll 3 Roll 4 ISO AO ISO A1 ISO A2 ISO A3 Bond Bond Bond Bond A NOTE It is not possible to print while displaying Warming Up in the status indication 4 Ready is displayed in the status indication when KIP 7970 is available to print COPY SCAN PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES J 29 2 3 Chapter 2 Basic Operations 2 2 Turning off KIP 7970 1 Press cy side on the Power Switch to turn off the printer Press this side CAUTION 1 KIP 7970 an
29. ou print longer than 6 meters the image quality or the reliability of media feeding is not guaranteed 1 10 Chapter 1 Before Use 1 7 2 Media not to be used Do not use the following kinds of printing paper Doing so may damage the printer Excessively curled Folded 1 11 Chapter 1 Before Use 7 ael L e A CAUTION Do not use the paper with staple or do not use such conductive paper as aluminum foil and carbon paper The above may result in a danger of fire A NOTE 1 Print image may become light if printed on a rough surface of the paper 2 Print image may become defective if the print paper has an excess curl 3 It will cause paper mis fed poor print image or creasing if you use a paper that does not satisfy the specifications 4 Do not use a paper of which surface is very special such as thermal paper art paper aluminum foil carbon paper or conductive paper 5 Vellum exposed to air over a long period tends to cause a defective printing It is recommended to remove one round on the surface of the vellum roll from the beginning 6 Remove fully any adhesive from the roll that may remain due to tape placed by the media Supplier 7 Do not use papers with unpacked exposed in high low temperature amp humidity ina long period Such papers may result in mis feed defective image or paper creasing 8 It is recommended to trim the leading edge by using Initial Cut Ke
30. print 2 Remove the media from the machine with plain paper and vellum right after the completion of print and High keep it in a plastic bag NOTE 1 KIP 7970 is equipped with the Dehumidify Heater Using it in high humidity environment 65 or higher is recommended Refer to 2 7 Dehumidifying Roll Media 2 Void of image and crease of paper will occur in case of extremely high or low humidity Normal Print Crease of paper If the media is humidified If the media is humidified continued on the next page 1 13 Chapter 1 Before Use A NOTE cont 3 Re appearance of image solid black image especially may occur if you print with a humidified film When film is installed under the high humidity environment higher than 6096 RH we also recommend that you turn on the Dehumidify Heater Normal print Re appeared image 1 14 Chapter 1 Before Use Chapter 2 Basic Operations page Turning on KIP 7970 nnn 2 9 Turning off KIP 7970 dd 2 4 Replacing Roll Media dit 2 B Replacing Toner Cartridge e 2 13 Placing Cut Sheet Media e 2 17 Canceling Sleep Mode e 2 18 Dehumidifying Roll Media 7 7 7 7 7 M M 2 19 Stacking Prints on High Capacity Print Tray option 2 21 2 1 Chapter 2 Basic Operations 2 1 Turning on KIP 7970 1 Plug the power cord f
31. slide 2 6 Chapter 2 Basic Operations 4 Insert each Flange 2 into both ends of the roll media core to be installed A NOTE 1 Fully insert Flange into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media Correct Fully inserted not touching roll side 2 Flange has Stoppers 6 with sharp edge Be sure not to touch them 2 7 Chapter 2 Basic Operations 5 Push both the levers 4 down in either way Position them flat against Flange to secure the roll media Continued on the next page 2 8 Chapter 2 Basic Operations NOTE 1 Note the rewinding direction Hear Deck back Hear Deck back Front to media path Front to media path Correct Edge comes from bottom Wrong Edge comes from top 2 The outside rim 7 of Flange should meet the black triangle 8 marked on Slide Guide Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding Correct 2 9 Chapter 2 Basic Operations 7 Insert the leading edge under Guide Plate 9 until it touches the feeding roller 10 Front Deck Roll 1 3 Rear Deck Roll 2 4 mi 7 2 10 Chapter 2 Basic Operations 8 Rotate the green knob 11 to the arrow direction away from front so that the feeding rollers catch the leading edge Front Deck Roll 1 3 Rear Deck Roll 2 4 A NOTE 1 Be sure to close R
32. the concerning Roll Deck toward the printer to firmly close it A NOTE The above screen will be indicated if the Roll Deck is not locked correctly although it may look closed Open and close the Roll Deck again pushing until locked Ensure both sides of the roll deck are in their correct position Correct firmly closed Wrong not closed completely 3 18 Chapter 3 Error Correction 3 2 2 Upper Frame Unit Top Cover Front Cover Open If either Upper Frame Unit or Top Cover is open the Ul screen shows Door Open Check if the Upper Frame Unit and the Top Cover are closed firmly Top Cover Upper Frame Unit Correct Both Top Cover Upper Frame Unit closed firmly 9 p Ly Resi bat Wrong Top Cover open Wrong Upper Frame Unit open 3 19 Chapter 3 Error Correction 3 2 3 Paper Exit Door Paper Exit Door Open If Paper Exit Door is open the Ul screen shows Paper Exit Door Open Check if Paper Exit Door is closed firmly Paper Exit Door 3 20 Chapter 3 Error Correction 3 3 Other Operator Call 3 3 1 Roll Replacement When the printer is running out of a loaded roll media the Ul Screen will display Out of Paper sign If there is no suitable roll media required for the current print job the Ul Screen will display Out of Paper sign as well Please load the required roll media to any Roll Deck For the roll replacement procedure see 2 3 Replacing the Roll Media
33. y on the User Interface Ul before making a long print 1 7 3 Maintaining Media Keep the paper in the custody taking care of the following matters Do not expose the paper to the direct sunlight Keep the paper away from high humidity It must be less than 70 Put the paper on a flat place do not damage the media If you will keep paper which you has already been unpacked put it into the plastic bag to avoid humidity in the media pup I 1 12 Chapter 1 Before Use 1 7 4 Environmental Condition Correction Take a necessary treatment according to the environmental condition as shown below Humidity Possible problem Necessary treatment Void of image crease of paper and 1 Install the humidifier in the room and other problems occurs when you print humidify the room air with plain paper and vellum 2 Remove the media from the machine right after the completion of print and keep it in a plastic bag Void of image occurs when you print If you will not make print soon remove with vellum the vellum from the machine and keep it in a plastic bag Remove the paper from the machine after everyday use and keep it in a plastic bag Void of image occurs when you print If you will not make print soon remove with plain paper and vellum the media from the machine and keep it in a plastic bag Void of image crease of paper and 1 Turn on the Dehumidify Heater other problems occurs when you
Download Pdf Manuals
Related Search