Telescopic Pole Mount CE-CM-S-2 CE-CM-SX-6 CE-CM-SX
Contents
1. the pole where it attaches to the structure using a 7 16 wrench 2 Place a level on the pole and tighten the nuts that correspond to the direction that the pole needs to move see illustration on the right Pole will move in the direction of the tightened bolt 3 Check and adjust 2 adjacent sides of the pole until it is plumb in each direction Adjusting Height 1 Hold the lower pole where it connects to the LCD while loosening the center collar by turning it counter clockwise see illustration on left below Extend the pole by gently lowering it to the desired length 2 Once the proper length has been maintained lock the pole in position by rotating the center collar clockwise The collar should be hand tightened as snug as possible to prevent the pole from expanding see illustration on right below Loosen Tighten Secure assembly by turning collar clockwise Hold lower pole section and hand tighten as snug as possible turn counter clockwise to loose Prevent display from falling by holding lower pole section here Installing the Safety Cable 1 Run the safety cable into the cable management hole in the top of the pole and out through the bottom of the pole The crimped eyelet end will connect to the LCD 2 Remove one of the M4 x 8mm VESA mount screws from the LCD bracket assembly then connect the crimped eyelet end of the safety cable to the mo2. M4 x 8mm VESA screws 4 places NOTE Some installations may require running power and video cables prior to attaching the LCD bracket to the pole If this is the case do so before continuing to step 2 2 Hold the LCD with attached bracket up to the end of the pole mount and M4 Washer line up the wings of the bracket to the holes in the end of the pole Insert the ae da 1 4 20 x 2 bolt lock washer washers and lock nut in place according to the 1 4 20 x 2 ene ock Nut illustration on the right You will use 7 16 and 10mm wrenches to fully tighten 1 4 Lock Washer in step 4 1 4 Washer M4 x 8mm VESA screw 3 Install the M4 x 45mm screw washers and lock nut into the upper slotted hole 4 places 1 4 Washer according to the illustration on the right You will use a 2 Phillips screwdriver and a 7mm wrench to fully tighten in the next step ss Max Load 15kgs 35lbs 4 Tighten the fasteners to secure the monitor at the desired angle NOTE Avoid overtightening which can cause the pole to indent CAUTION This stand is intended for use only with the maximum weights indicated Use with products heavier than the maximum weights indicated may result in instability causing possible injury This product is intended to mount to a steel support truss or channel strut Leveling the Pole 1 You can ensure the pole is plumb by tightening the 1 4 20 lock nuts on the top of
3. Telescopic Pole Mount CE CM S 2 CE CM SX 6 CE CM SX 8 CE CM LX 12 CE CM LX 17 User Manual CLINTON Electronics 1 800 447 3306 Sales i 6701 Clinton Road 1 800 549 6393 Support www clintonelectronics com CLINTON Electron cs Loves Park IL 61111 1 800 633 8712 Fax WARNING Prior to installation and use of this product please observe the following warnings 1 Installation and servicing should be done by qualified personnel and all work done should conform to local codes 2 Using replacement parts or accessories other than from the manufacturer may void the warranty CAUTIO N 7 This symbol indicates that there are important operating and CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT Telescopic LCD ceiling mount Info This bracket is designed to mount to mount an LCD from the ceiling structure It can be used with the existing truss structure of the building or in conjunction with channel strut There are four lengths of brackets available Part CM S 2 e Part CM SX 6 e Part CM SX 8 ePart CM LX 12 e Part CM LX 17 Length of 22 to 35 Length of 36 to 67 Length of 54 to 96 Length of 71 to 139 Length of 75 to 200 Brackets are identical except for length Included Hardware amp 1 2 13 lock nut 1 pc and fender washer 1 pc Safety cable with crimped eyelet 1
4. pc gae 1 4 20 x 2 hex head bolt 1 pc M4 x 45 screw 1 pc lock washer 1 pc washers 2 pcs washers 2 pcs and locknut 1 pc and locknut 1 pc 3 U bolt cable M4 x 10mm screw M4 x 8 VESA screws clamp 1 pc to attach safety cable 4 pcs to rear of display 1 pc maintenance instructions in the literature accompanying this unit Tools Required 7 16 wrench 7mm wrench 10mm wrench 3 4 wrench 5 16 wrench 2 Phillips head screwdriver level Bracket 1 pc J U User Manual Pole Mount 1 pc Assembly 1 pc Please check to ensure all hardware is included prior to installation If parts are missing please contact Clinton Electronics for replacement parts Assembly Instructions seam gee Fender Washer If drilling is necessary Truss mount or channel strut mount Ce a CCRC bit to drill through steel ce mounting surface Securing Mount to Building 1 Insert threaded rod between truss gap or into hole in channel strut Min Hole Size 1 2 2 Place 1 2 fender washer over the threaded rod and then 1 2 lock nut Mare Moeaa P A Min Steel Thickness 1 4 3 Tighten the 1 2 13 lock nut using a 3 4 wrench Mounting LCD to Pole 1 If your LCD is supplied with a VESA plate already mounted on the back simply ensure the four M4 screws are in place and tightened If the mount is not already attached connect it using the supplied
5. unt using the supplied M4 x 10mm screw You can discard the unused M4 x 8mm VESA mount screw that has been removed as it is no longer needed 3 Connect the top end of the safety cable by inserting it through a hole in the truss or channel strut and fasten using the U Bolt cable clamp Pull any remaining slack from the safety cable and fully tighten the U Bolt using a 5 16 wrench Cut or loop any excess cable Remove original M4 x 8mm VESA screw amp replace with M4 x 10mm screw a Cord Management Hole CLINTON Electronics 1 800 447 3306 Sales CLINTON Electronics 6701 Clinton Road 1 800 549 6393 Support www clintonelectronics com Loves Park IL61111 1 800 633 8712 Fax v 04 06 11
Download Pdf Manuals
Related Search