MT0404-VL4 User Manual
Contents
1. 10801 1080P 3D 2 0CH 5 1CH 7 1CH USER1 Output and Input select A OUTPUT X select INPUT Y 1 Press OUTPUT X X means 1 to 4 of outputs 2 Press INPUT Y Y means 1 to 4 of inputs 2 Press OUTPUT X X means 1 to 4 of outputs press the left and right arrow buttons to select the input B All outputs select INPUT Y Press ALL button in zone OUTPUT 2 Press INPUT Y button Y means 1 to 4 of inputs then INPUT Y switched to ALL OUTPUTS C Mirror all inputs and outputs Ex Input 1 to output 1 input 2 to output 2 etc Press PTP button in Zone OUTPUT MT0404 VL4 User Manual EDID Set Up A Fixed EDID to INPUT Y ALL Press 10801 1080P 3D A4K Press 2 0CH 5 1CH 7 1CH INPUT Y ALL button in Zone INPUT B Copy EDID of OUTPUT X to INPUT Y ALL Press COPY button Press OUTPUT X button Press INPUT Y ALL button NOTE Copy priority is from the HDBT output so if demand to copy HDMI output EDID first need to unplug HDBT output under the same group and then perform the copy C User defined EDID to INPUT Y ALL Press USER1 USER2 button Press INPUT Y ALL NOTE Pressing button sequence should be finished in 5 seconds otherwise operation discarded MT0404 VL4 User Manual Application Diagram IR Receiver Link to Control Device Blu Ray DVD DVD Sink 5 Game Console ik 70m 230ft 70m 230ft 70m 230ft 70m 230ft HDBT Receiver HDBT Re2. 00100 10 RS 232 and Telnet Commands 442 40 1 0 11 QUI control 2 LR Hate 11 Mainteriance 21 2 teet e edes Do 22 Warranty PoliGy i idet eias eue eios 22 Limitations of isse tette eene Re 22 Exclusive Bemedies u rre ort rrr ul e tesi nei 22 RMA PONCY i eu ee re RARE ERU ee tee nae vias 23 MT0404 VL4 User Manual Introduction The MT0404 VL4 HDBaseT 4x4 Matrix for HDMI routes four Hi Def sources to any four HDTV displays supporting 1080p Full HD plus all 3D formats along with multichannel digital audio formats such as Dolby True HD and DTS HD Master Audio Based on HDBaseT Lite chipset inside the output distance can reach up to 70m via Cat5e Cat6 Each source can be routed to any display using the front panel push buttons IR remote control RS 232 interface or via TCP IP Warning CCA Category Cable should not be used with this product Features e Supports resolutions up to 1080p 960HZ 36 bit deep color e HDBaseT Lite chipset inside for the output distance up to 70m e Matrix can power the remote receivers via POC so no power supply is needed for the receivers e Allows any source to be displayed on multiple displays at the same time e Allows any HDMI display to view any HDMI source at any time e Dolby TrueHD and DTS HD master audi
3. Define tags for respective Output port then displays connect the Output ports be easily remembered Click buttons with x caption to delete tag which is no use any more if tag is still used by any other Output port delete action will be discarded 17 MT0404 VL4 User Manual Setting page 3 4x4 HDMUHDBT Matrix Controller ver1 4 Pre Settings bn pis 3 Output 5 17 Settng2 3 Setting3 Settings ERSTE 3 co Sening Setting8 Output from Input M by od be d 2 Uu UJ General Port Setting EDID control Advanced FW upgrade Connected 192 168 0 123 Done 2013 12 13 1432 LED which displays Input number for respective Output port Click to select Input port for respective Output port Click to select previous or next Input port for respective Output port Display Output from Input with tag information when mouse moves over Zbuttons Pre Setting items Default is Port to Port Click to edit selected pre setting item NO OP ON Set selected pre setting item to Matrix NOTE When Change to this Setting page software will try to refresh source selection status of Output port 18 MT0404 VL4 User Manual Pop up tag messages When Display Input Output tags when fo
4. UK Ltd The warranty does not apply to any product or parts thereof where the serial number or the serial number of any of its parts has been altered defaced or removed The warranty does not cover damage or loss incurred in transportation of the product The warranty does not cover replacement or repair necessitated by loss or damage from any cause beyond the control of Aclass Technology UK Ltd such as lightning or other natural and weather related events or wartime environments The warranty does not cover any labor involved in the removal and or reinstallation of warranted equipment or parts on site or any labor required to diagnose the necessity for repair or replacement The warranty excludes any responsibility by Aclass Technology UK Ltd for incidental or consequential damages arising from the use of the equipment or products or for any inability to use them either separate from or in combination with any other equipment or products A fixed charge established for each product will be imposed for all equipment returned for warranty repair where Aclass Technology UK Ltd cannot identify the cause of the reported failure Exclusive Remedies 25 MT0404 VL4 User Manual Aclass Technology Ltd s warranty as stated is in lieu of all other warranties expressed implied or statutory including those of merchantability and fitness for a particular purpose The buyer shall pass on to any purchaser lessee or other us
5. the matrix from a computer 7 HDMI inputs 1 to 4 Connect HDMI sources 8 HDBT outputs 1 to 4 Work with remote receivers for long distance transmission 9 HDMI outputs 1 to 4 Output for displays AVR etc 10 IR extension receiver input 3 5mm stereo phone jack 11 POC Power port Use included 12V 5A DC adaptor to power the remote receivers 12V 5A DC adaptor to power the matrix switcher MT0404 VL4 User Manual Side Panel 1 EDID DIP switch UP 0 DOWN 1 DIP 0000 HDMI 1080p 60Hz Audio 2CH PCM 01 1111 EDID control by Remote Control Terminal enabled DIP 0001 HDMI 1080p 60Hz Audio 5 1CH PCM DTS DOLBY DIP 0010 HDMI 1080p 60Hz Audio 7 1CH PCM DTS DOLBY HD DIP 0011 HDMI 1080i 60Hz Audio 2CH PCM DIP 0100 HDMI 1080i 60HZz Audio 5 1CH PCM DTS DOLBY DIP 0101 HDMI 1080i 60HZz Audio 7 1CH PCM DTS DOLBY HD DIP 0110 HDMI 1080p 60Hz 3D Audio 2CH PCM DIP 0111 HDMI 1080p 260Hz 3D Audio 5 1CH PCM DTS DOLBY DIP 1000 HDMI 1080 2 Audio 7 1CH PCM DTS DOLBY HD DIP 1001 HDMI 4K2K Audio 2CH PCM DIP 1010 HDMI 4K2K Audio 5 1 CH PCM DTS DOLBY DIP 1011 HDMI 4K2K Audio 7 1 CH PCM DTS DOLBY HD DIP 1100 DVI 1280x1024 60Hz Audio None DIP 1101 DVI 1920x1080 260Hz Audio None DIP 1110 DVI 1920x1200 960Hz Audio None MT0404 VL4 User Manual Remote Control Description ES POWER OUTPUT 1 2 3 4 ALL PTP
6. 04 zz 00 HDMI 1080p 60Hz Audio 2CH PCM 22 01 HDMI 1080p 60Hz Audio 5 1CH PCM DTS DOLBY 22 02 HDMI 1080p 60Hz Audio 7 1CH PCM DTS DOLBY HD 22 03 HDMI 1080i 60Hz Audio 2CH 22 04 HDMI 1080i 60Hz Audio 5 1CH PCM DTS DOLBY zz 05 HDMI 1080i 60Hz Audio 7 1CH PCM DTS DOLBY HD 22 06 HDMI 1080p 60Hz 3D Audio 2CH 14 EDID xx DF zz 22 07 HDMI 1080p 960Hz 3D Audio 5 1CH PCM DTS DOLBY 22 08 HDMI 1080p 960Hz 3D Audio 7 1CH PCM DTS DOLBY HD zz 09 HDMI 4K2K Audio 2CH PCM zz 10 HDMI 4K2K Audio 5 1 PCM DTS DOLBY 22 11 HDMI 4 Audio 7 1 PCM DTS DOLBY HD 22 12 DVI 1280x1024 60Hz Audio None zz 13 DVI 1920x1080 60Hz Audio None zz 14 DVI 1920x1200 60Hz Audio None 12 OUT xx FR yy GUI Control PC System Microsoft Windows Operation System Installation 4x4 HDMI Matrix controller is a green software You just need to copy 4x4 HDMI Matrix Controller vx x exe to the PC which is used to control the Matrix by RS232 COM or TCP to complete installation Preparation 1 Connect PC and Matrix RS232 cable or UTP cable 2 Power up Matrix It will take about 5 seconds to be ready with Di beep sound 3 Double click 4x4 HDMI Matrix Controller vx x exe icon to run it How to control Matrix Common information 13 MT0404 VL4 User Manual General Port Tag Setting EDID control IR Configuration FW upgrade Click to select tab page Connect
7. AT cable 5 To reduce the interference among the unshielded twisted pairs of wires in CAT cable do not run HDBaseT Zone Cat5e 6 6a cabling with or in close parallel proximity to mains power cables Shielded CAT cables Can be used to improve EMI problems which is worsen in long transmission 6 Because the quality of the CAT6 cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality the actual transmission range is subject to one s choice of CAT 6 cables 7 Do not substitute or use any other Power Supply other than the enclosed unit or a Aclass Technology approved Replacement Part Doing so will void the warranty and potentially expose the user to dangerous voltages resulting in an electrical shock 8 Do not disassemble the device for any reason Doing so will void the manufacturer s warranty Also our unique case is an integral part of the design of this unit and is responsible for cooling and circuitry shielding Any modifications to this case will potentially cause malfunction and product failure 9 Do not expose the device to water moisture or liquids Possible electric shock may result as well as failure of the unit to operate Warranty Policy 24 MT0404 VL4 User Manual Aclass Technology UK Ltd products are warranted against defects in material and workmanship for two years from the date of shipment During the warranty period Aclass Technology UK Ltd
8. MT0404 VL4 User Manual MT0404 VL4 User Manual MT0404 VL4 User Manual Thank you for purchasing this product For optimum performance and safety please read these instructions carefully before connecting operating or adjusting this product Please keep this manual for future reference SURGE PROTECTION DEVICE RECOMMENDED This product contains sensitive electrical components that may be damaged by electrical spikes surges electric shock lightning strikes etc Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment MT0404 VL4 User Manual Safety Notice 1 The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY 1427071 6 2 EIA TIA 568 B termination T568B for CAT cables is recommended for better performance 3 DO NOT use 568A 568B standard mixed CAT cable cross over cable because there are 2 pairs swapped this will make POE OVER CURRENT and damage POE components Please use straight through CAT cable both RJA5 headers are 568A or 568B standard 4 It is recommended that power up the device after connections of source sink and CAT cable 5 reduce the interference among the unshielded twisted pairs of wires CAT cable do not run HDBaseT Zone Cat5e 6 6a cabling with or in close parallel proximity to mains power cables Shielded CAT cables can be used to improve EMI problems which can be worse in longer transmissions 6 B
9. ceiver HDBT Receiver HDBT Receiver Connection of IR Emitter and Receivers For transmitting IR from TV locations for controlling the matrix as well as any source device First connect the larger of the IR Emitters into the RX slot on the receivers Secondly put the smaller of the IR pieces into the IROUTPUT Slot on the back of your matrix You should notice that the IR Slots are numbered please note that they relate to the source number The sources IR pick up maybe difficult to locate and you may have to move the IR piece to various angles If you need to send IR from the matrix location to your TV location this could be done by putting the Larger IR Pieces into the IR INPUT Slot on the back of the matrix You will also need to place the smaller IR Pieces into the TX Slot on the receivers 10 MT0404 VL4 User Manual Specifications Bandwidth 2 97Gbps Video Input Connectors 4x HDMI Type A 19 pin female locking Video Output Connectors 4x HDMI Type A 19 pin female locking 4x RJ 45 connector RS 232 serial port 5x DB 9 female TCP IP Control 1x RJ 45 female IR Input ports 5x 3 5mm stereo jack R Output ports 4x 3 5mm stereo jack Rack Mountable 1 U rack height rack ears included Shipping Weight 2 7kg Operating Temperature 32 F to 104 F 0 C to 40 C Storage Temperature 4 F to 140 F 20 C to 60 C Power Supply 12V 5A DC main 12V 5A DC POH Dimensions W x H x D 428mm x 245mm x 43mm w
10. ct to availability the replacement product will be shipped on the business day following receipt of the defective product In the event the product returned to Aclass Technology UK Ltd has been discontinued i e the product is no longer being manufactured by Aclass Technology UK Ltd but is still under warranty Aclass Technology UK Ltd will at its discretion either repair or replace with recertified product Once you have obtained an RMA number After obtaining an RMA number from Aclass Technology UK Ltd you must send the product freight prepaid to Aclass Technology UK Ltd The Aclass Technology UK Ltd RMA number must be prominently displayed on the outside of your package If you send your product to Aclass Technology UK Ltd without the RMA number prominently displayed on the outside of the package it will be returned to you unopened Please use a shipping company that can demonstrate proof of delivery Aclass Technology UK Ltd does not accept responsibility for any lost shipments unless proof of delivery to 26 MT0404 VL4 User Manual Aclass Technology UK Ltd is provided Please note Product shipped to Aclass Technology UK Ltd must be properly packaged to prevent loss or damage in transit Shipping your RMA to Aclass Technology UK Ltd using regular mailing envelopes is not acceptable as they do not protect the product from damage during shipping Aclass Technology UK Ltd will not repair or re
11. cus setting buttons checkbox on General page is checked and Input output port tag has been defined tag messages will pop up like as 2 4x4 Matrix Controller ver1 4 gt Pre Sentings Name Outpu Oupa 1 1 1 1 1 1 1 1 Output Output Oupa Output Setingl 3 Setting Setting3 Settings ath Settings 312 3141 11215 41 3121313 Settings 1 213141 815 Ourpati LG TV Output3 SAMSUNG TV fron Output SONY Output3 SAMSUNG TV Outputs PANASONIC TV Input SONY DVD Input SAMSUNG DVD Input PS3 Input4 XBOX 360 F2 P2 Ud od Ud QU QU ou de de da de de de de Ser General Poet Tag Setting EDID control Advanced FW upgrade Comectet 192 168 0 123 Done 2013 12 13 1438 When mouse moves over 2 buttons and click mouse right button menu will pop up like as 11213134 Al Outputs 3 92 Bs Ar 4 4 1 Output Outputs SAMSUNG TV from Imput 3 Outpues 4 Outputs Port to Port General Poet Setting EDID control Advanced FW upgrade Comected 192 168 0 123 Done All Outputs All Outputs from same Input 19 MT0404 VL4 User Manual 1 Output to 4 Outputs Set current Output where mouse right clicked and the next x 1 range is from 1 to 4 set total x Outputs at the same time O
12. ecause the quality of the CAT5 6 cables has a major effect on the length of which the transmission can reach and also picture quality the actual transmission range is subject to one s choice of CAT cables 7 Do not substitute or use any other Power Supply other than the one enclosed or a Aclass Technology approved Replacement Part Doing so will void the warranty and potentially expose the user to dangerous voltages resulting in an electrical shock 8 Do not disassemble the device for any reason Doing so will void the manufacturer s warranty Also our unique case is an integral part of the design of this unit and is responsible for cooling and circuitry shielding Any modifications to this case will potentially cause malfunction and product failure 9 Do not expose the device to water moisture or liquids Possible electric shock may result as well as failure of the unit to operate MT0404 VL4 User Manual 10 11 12 13 14 15 Table of Contents be bte eqs Du uper pi ied 4 Features eso ote bon DEI Red HV Vio tO Re dude todas 4 Pariel Descriptions 4 Remote Control Descriptions s o i retreat etatem ded eben duet beds 7 Application Diagram nett Been Re dev eae 8 SpecificatlofiS ioc eee pete dot T preci rp cia 9 Package Contents iae RE e ieee a vc roue do bi v e e ed ee 9 RS 232 Pin
13. ed 192 168 1 121 Done Omm 10 17 COM port or TCP connect status Control command process status Prompt message display area Date and Time display peo Ie General page 3 4x4 HDMI HDBT Matrix Controller ver1 4 Control mode select COM control mode Device information COM control mode Port Device Not known 5 TCP control mode 52 Version Not known TCP control mode Input Not known Outputl Not known Input2 Not known HDMI Output2 Not known MT0404 VL 1 41 Static IP 192 168 0 123 00 15 09 22 4C 87 Sem X3 oad HDMI 3 Not known 5 Config Input Notknown HDMI Output Not known Connection 5 Connect Refresh device status Device status 7 Display tags setting Display Input Output tags when focus setting buttons General Port Taz Setting EDID control Advanced FW upgrade Disconnect 2013 12 13 14 26 Select control mode RS232 COM mode Auto COM ports detected or TCP mode List detected COM ports List all Matrix devices after search operation Click to search all Matrix devices that connected in same subnet Click to configuration the selected Matrix s TCP control configurations Click to connect or disconnect PC and Matrix Connection will be established automatically before control commands sending 7 Click to refresh device status include device information displayed in 9 area and Input output port co
14. er of Aclass Technology UK Ltd s products the aforementioned warranty and shall indemnify and hold harmless Aclass Technology UK Ltd from any claims or liability of such purchaser lessee or user based upon allegations that the buyer its agents or employees have made additional warranties or representations as to product preference or use The remedies provided herein are the buyer s sole and exclusive remedies Aclass Technology UK Ltd shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory RMA Policy When returning product to T Aclass Technology UK Ltd for any reason the customer should fill out the official RMA form to obtain a RMA number Without the permission or approval Aclass Technology UK Ltd will be no responsible for any return This can be initiated by emailing or calling your related sales All requests are normally processed within 48 working hours Standard Replacement For customers that agree to return defective product to Aclass Technology UK Ltd first a Standard Replacement option is available An RMA number must first be issued by sales This RMA number will need to be referenced on the outside of the return shipment Upon receipt of the defective product Aclass Technology UK Ltd will at its discretion either repair or replace the product and ship it out in the most expeditious manner possible Subje
15. grade progress 0 2 O Messages Clear 5 General Port Tag Setting EDID control Advanced FW upgrade Connected 192 168 0 123 Done 2013 12 13 14 50 1 Click to open firmware file file extension is fw 2 Firmware upgrade progress 3 Click the button to upgrade firmware 4 Firmware upgrading messages display 5 Click to clear the messages displayed in the memo box NOTE If failure occurs during upgrading firmware process the following steps SHOULD be done sequentially to establish next upgrading procedure Power down the Matrix 2 Close the 4x4 HDMI Matrix Controller 3 Re power up the Matrix then wait for 10 seconds to ensure the Matrix is ready 4 Run 4x4 HDMI Matrix Controller open firmware file and upgrade again 23 MT0404 VL4 User Manual Maintenance Clean this unit with a soft dry cloth Never use alcohol paint thinner or benzene to clean this unit Safety and Notice 1 The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY 1427071 6 2 EIA TIA 568 B termination T568B for CAT cables is recommended for better performance 3 DO NOT use 568A 568B standard mixed CAT cable cross over cable because there are 2 pairs swapped this will make POE OVER CURRENT and damage POE components Please use straight through CAT cable both RJ45 headers are 568A or 568B standard 4 It is recommended that power up the device after connections of source sink and C
16. it Input port tags 3 Output port tags 4 Click to edit Output port tags 4x4 HDMI HDBT Matrix Controller ver1 4 Output port tags 7 Tag of Output Tag of Output3 LG TV SAMSUNG TV Tag of Output Tag of Output4 SONY TV PANASONIC TV 2013 12 13 1428 NOTE Edit boxes are read only click Edit button to pop up window to edit the tags One set of Input output port tags can be set for Matrix device when COM control mode selected Input output port tags can be set for respective Matrix device according to device s MAC address 16 MT0404 VL4 User Manual Edit Input port tags After action of 2 edit form will pop up as below a Edit Input port tags Input port tags Device name connect 1 Device name connect Input3 soo 45 Device name connect Input2 Device name connect Input4 SAMSUNGDVD x Define tags for respective Input port then devices connect the Input ports be easily remembered Click buttons with x caption to delete tag which is no use any more if tag is still used by any other Input port delete action will be discarded Edit Output port tags After action of 4 edit form will pop up as below Edit Output port tags Output port tags Display name connect 1 Display name connect Output3 Display name connect Output2 Display name connect Output4 gt Panasonictv gt ox
17. ithout feet Package Contents 1 1x MT0404 VL4 2x 12V 5A DC power supply 1x Remote control 4x IR Transmitter 5x IR Receiver 1x mounting kit SOO 1x CD for control software 11 MT0404 VL4 User Manual RS 232 Pin Assignment MT0404 VL4 Remote Control Console PIN Assignment PIN Assignment 1 NC 1 NC 2 TX 2 Rx 3 Rx 3 Tx 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate 57600 bps Data Bit 8 bit Parity None Stop Bit 1 bit Flow Control None 12 MT0404 VL4 User Manual RS232 and Telnet Commands No Comand Action 1 Print Help Information 2 Print Help Information 3 Print System Status And Port Status 4 Power On System Run On Normal State 5 Power Off System Run On Power Save State 6 IR ON OFF Set System IR Control On Or Off 7 KEY ON OFF Set System KEY Control On Or Off 8 APM ON OFF Set Advanced Process Mode On Or Off 9 BEEP ON OFF Set Onboard Beep On Or Off 10 RESET Reset System To Default Setting Should Type Yes To Confirm No To Discard 11 OUT xx ON OFF Set OUTPUT xx On Or Off xx 01 04 Set OUTPUT xx From INPUT yy xx 00 Select All OUTPUT Port xx 01 04 Select One OUTPUT Port yy 01 04 Select One INPUT Port 13 EDID xx CP yy Set Input xx EDID Copy From Output yy Set Input xx EDID To Default EDID zz xx 00 Select All OUTPUT Port xx 01
18. nnection status in gx gie NOTE Tab pages cannot be changed during control command is processing 8 To enable or disable Input output tags displaying when setting buttons on Setting page focused 14 MT0404 VL4 User Manual 9 Device information display area 10 Input output port connection status Set TCP control configuration Click Config button to show TCP configuration window 3 configuration Device informabon Device Tag MT0404 VL 1 51 E AutoIP 6 Static IP 2 ess 192 he 4 6 1 Set tag to identify Matrix device 2 Set IP mode Subnet should support DHCP protocol when set Auto IP mode then Matrix device will obtain IP automatically Otherwise set Static IP mode and designate a useable IP for Matrix device 3 Set IP address not editable when Auto IP mode selected Note The last IP BYTE s range is 2 252 Matrix device MAC address 5 Click OK to set configuration If configuration is set OK Matrix devices will be searched out again 6 Click to Close the window and configuration cancelled 15 MT0404 VL4 User Manual Port Tag page a Input Tag of Input Tag of Input SONY DVD Sx Tag of Input2 Tag of Inputd SAMSUNGDVD Roxo 0 2 C General Port Tag Serting EDID control Advanced FW upgrade Disconnect Modify TCP configuration cancelled 1 Input port tags 2 Click to ed
19. o pass through HDMI output e Advanced EDID management for rapid integration of sources and displays e Front panel LCD display for status feedback e Multiple switching mode push in button IR remote control RS 232 control and TCP IP control Easy installation with rack mounting ears e Full 3D pass through e HDCP compliant MT0404 VL4 User Manual Panel Descriptions Front Panel 0 o Or tta OF 1 1 1 Power LED indicator Indicate the status of the power for the matrix 2 IR receiver window Receive the IR from the remote control of MT0404 VL4 3 Output selection button from 1 to 4 Press to change the I O connections of output 1 to 4 4 Input LED indicator Show the status of selected input Back Panel 7 8 2 09000000 e o Gem foam SL es E Sl eres oo LJ TCP IP RS232 HMI HOMI 2 HOMIS HDMI L Host Hoar l 5 6 7 8 9 1041 42 1 IR inputs 1 to 4 3 5mm stereo phone jack 2 IR outputs 1 to 4 3 5mm stereo phone jack 3 RS232 port with each HDBT out Connect to PC and work with the remote receiver 4 Grounding screw 5 RJ45 TCP control 6 RS232 port Connect to this port for control of
20. place a module that is shipped in such a way that the product is not properly protected Aclass Technology UK Ltd will not accept any product that has been damaged as a result of accident abuse misuse natural or personal disaster or any unauthorized disassemble repair or modification r modification 27
21. ut port to selected Input port or All Input ports click Copy button to complete action 3 Read EDID content from Output port and display in grid click Read button to complete action 4 Save EDID content which displayed in grid to binary file file extension is bin Open EDID binary file and display in grid 6 Download EDID content which displayed in grid to selected Input port or All Input ports click Download button to complete action When User1 Memory User2 Memory selected download EDID content to respective memory then User1 User2 EDID mode can be set 7 EDID content displaying grid NOTE EDID content displayed in grid is read only 8 Click to clear EDID content displayed in grid 21 MT0404 VL4 User Manual IR Configuration page 0 a 4x4 HDMI HDBT Matrix Controller ver1 4 IR control enable disable setting Enable IR control TCP Module infomation O Reset TCP Module General Port Tag Setting EDID control Advanced FW upgrade Connected 192 168 0123 Done 2013 12 13 14 49 To enable or disable IR control function When box checked IR control function enabled otherwise IR control function disabled This setting is not memorized IR control function is always enabled after power up 22 MT0404 VL4 User Manual FW upgrade page 3 4x4 HDMI HDBT Matrix Controller ver1 4 zx FW upgrade Open FW file rj 1 Up
22. utput s from same Input Port to Port Output from Input1 Output2 from Input2 Output3 from Input etc Edit selected pre setting item After action of 6 edit form will pop up as below 3 Edit Output setting Output setting 7 SC 7 2 V Setting name 1 Ourputs from Setting Select Input z Out LG TV from Out3 SAMSUNG TY from Ini SONY DVD M PS3 2 SONY TV from Out4 PANASONIC TV from In SAMSUNG DVD XBOX 360 OK Caes 1 Pre Setting name 2 Set all Output ports from same Input 3 Select Input for respective Output 20 MT0404 VL4 User Manual EDID control page 4x4 HDMUHDBT Matrix Controller ver1 4 45 EDID mode control Set EDID mode Select EDID 10 Select Input 1 Set Copy EDID from Select Ourput fto Select Input 2 Copy EDID data control Read EDID datafrom Select Output 3 Read Save to EDID file gt Open EDID fie 5 Download EDID data to Select Input Download General Port Setting EDID control FW upgrade Connected 192 168 0 123 2013 12 13 1448 1 Set EDID mode for selected Input port or All Input ports click Set button to complete action NOTE When set User1 User2 EDID mode should Download EDID content to User1 Memory User2 Memory first User1 User2 default EDID content is 1080p Stereo Audio 2 0 2 Copy EDID from Outp
23. will at its option repair or replace products that prove to be defective Repairs are warranted for the remainder of the original warranty or a 90 day extended warranty whichever is longer For equipment under warranty the owner is responsible for freight to Aclass Technology UK Ltd and all related customs taxes tariffs insurance etc Aclass Technology UK Ltd is responsible for the freight charges only for return of the equipment from the factory to the owner Aclass Technology UK Ltd will return the equipment by the same method i e Air Express Surface as the equipment was sent to Aclass Technology UK Ltd All equipment returned for warranty repair must have a valid RMA number issued prior to return and be marked clearly on the return packaging Aclass Technology UK Ltd strongly recommends all equipment be returned in its original packaging Aclass Technology UK Ltd s obligations under this warranty are limited to repair or replacement of failed parts and the return shipment to the buyer of the repaired or replaced parts Limitations of Warranty The warranty does not apply to any part of a product that has been installed altered repaired or misused in any way that in the opinion of Aclass Technology UK Ltd would affect the reliability or detracts from the performance of any part of the product or is damaged as the result of use in a way or with equipment that had not been previously approved by Aclass Technology
Download Pdf Manuals
Related Search