Assembly instructions
Contents
1. mm above the sealing scale 25 Plug the control knob in the sealing scale Make sure that the indication of the button corresponds to the indication of the sealing scale Important TT BY REGINOX When not properly adjusted the burners will not ignite For warranty and the proper functioning of the cooking unit ensure the mounting is as described in this manual to the letter 18 Press the control knob down firmly When releasing the control knob will be in the adjustment position see Photo 19 22 Check all control buttons for the right height and adjust if necessary with the set screws 3 26 Press the control knob on the gas as a whole and sealing scale and press it on the worksheet 19 The bottom of the control knob is visible above the sealing scale 23 Check each gas burner for ignition and if they remain lit If that is not the case then check the button height again 27 Check each gas burner for ignition and if they remain lit and or for proper functioning Check malfunctions on next page 20 Tighten the set screws 3 See Photo 14 clockwise so that the control knob in the sealing scale drops 24 Remove the adhesive strip from the sealing scale If you have any questions you can always give us a call or send us an e mail Reginox Far East PITT by Reginox 2 Loyang Lane 03 03 Singapore 508913 T 65 0 67 88 53 63 F 65 0 67 88 38 35 info reginox com s2. 1 JN Rijssen info reginox com www pittbyreginox com www pittbyreginox com
3. Y Assembly instructions j TT BY REGINON Assembly instructions 1 Overview components 5 Place the heat conductor on the unit 9g Attach the heat shields hand tight 13 Connect the gas hose Then place the plug into a grounded wall socket 2 Press the sealing ring gently on the edge of the heat shield Verify that the ring is not damaged 6 Position the unit gently under the countertop 10 For the stir fry cooker make sure that the V shaped notch is in line with the axis of the burner Gasconnection 14 Overview set screws 3 Overview set screws 7 Place the heat shields on the burners Make sure you use the recesses 11 Make sure to place the pan carriers on the fixation pin This provides stability 15 Pivot all set screws 1 hand tight until the thermal conductor comes in contact with the bottom of the countertop 4 Loosen the set screws in order position 1 2 amp 3 back to approximately 3 mm above the unit 8 The 2kW and 3kW heat shield can only be placed in one position 12 The burner is complete 16 Tighten both set screws 2 hand tight until the thermal conductor comes in contact with the bottom of the countertop 17 Positioning all sealing scales including the con trols on the worksheet Please note first tweaking in position no adhesion yet 21 Let the buttons go down until the button extends for a minimum 5 mm and up to 7
4. g www pittbyreginox com Assembly instructions BY REGINOX Attention The PITT by Reginox system may only be connected by an approved installer To ensure the safety and warranty repairs may only be performed by approved professionals You Should only use original parts A burner ignites The control knob is not pressed Hold the button pressed for a See user manual and turns off long enough to activate the flame few seconds after igniting again protection The control knob is not adjusted Reset the control knob Assembly instructions at the correct height step 19 t m 22 The control but Hob is not mounted the right way Reset the control knob Assembly instructions ton touches the under the countertop step 14 t m 22 sealing scale Sealing scale is not in the center Detach sealing scale and adhere Assembly instructions vs control knob again step 25 t m 26 Spark ignition Hob is not mounted the right way Set the control knob well off Assembly instructions remains igniting under the countertop step 14 t m 22 Sealing scale is not in the center Detach sealing scale and adhere Assembly instructions vs control knob again step 25 t m 26 A burner does not The control knob is not adjusted Reset the control knob Assembly instructions kindle at the correct height step 19 t m 22 The plug is not in the Insert the mains plug into the Installation instructions outlet wall outlet step 13 Fu
5. se is defect or the central fuse Mount a new is turned off fuse or switch on the fuse again Spark ignition is polluted or Clean or dry the spark ignition See user manual humid Burner parts are not mounted Put the burner parts together by See user manual correctly the spigot Burner parts are polluted or Clean dry the See user manual humid Burner parts Make sure the outflow holes are open Main gas tap is closed Open the main gas tap Sy Control knob is not pressed long Keep the control knob pressed See user manual or deep enough long enough and sufficiently between full and small gas Burner parts are not properly Burner parts are not properly See user manual placed placed Put the burner parts together by the spigot Burner parts are polluted or Clean dry the burner parts Make See user manual humid sure the outflow holes are open Gas connection leaks Check the connection Turn main A burner is not lit evenly Gas smells in Surroundings of cooker gas valve off when you re not able to fix it right away There is a burner turned on but Close the control knob and wait See user manual not ignited a few minutes with rekindling Reginox Far East Reginox The Netherlands PITT by Reginox T 65 0 67 88 53 63 PITT by Reginox T 31 0 548 53 56 35 2 Loyang Lane 03 03 F 65 0 67 88 38 35 Noordermorssingel 2 F 31 0 548 53 56 00 Singapore 508913 info reginox com s g 746
Download Pdf Manuals
Related Search