Blade-550 (550x0.1g) - User Manual
Contents
1. Weigh Scales Inc BLADE Series 50 0000000 00 User Manual BLADE 550 BLADE 1000 Blade Series Manual Thank you for purchasing the American Weigh BLADE Series digital scale Please read all operating instructions carefully before use This electronic scale is a precision instrument With normal care and proper treatment it will provide years of reliable service Never load the scale with more than the maximum capacity Overloading will permanently damage it Avoid any exposure to extreme heat or cold Your scale works better when operated at normal room temperature Always allow the scale to acclimate to normal room temperature for at least one hour before use Give your scale sufficient warm up time Usually 30 60 seconds before calibration to give the internal components a chance to stabilize Keep your scale in a clean environment Dust dirt moisture vibration air currents and a close distance to other electronic equipment can all cause an adverse effect on the reliability and accuracy of your scale Handle with care Gently apply all items to be weighed onto tray top Although this scale is designed to be quite durable try to avoid rough treatment as this may permanently damage the internal sensor Avoid shaking dropping or otherwise shocking the scale This is a precision instrument and must be handled with extreme care Only operate the2. 6802 32 150zt 250ct 257 2dwt 353 7dwt 643 1dwt 771 59 Resolution 0 01g 0 19 0 00102 0 0102 0 05 0 19 0 2gn Weighing Units 9 02 ozt dwt 9 02 ct gn Calibration Weight not Included 400g 500g 10009 509 Platform Dimensions inches 2 75 x 2 75 Stainless Steel Scale Dimensions inches 375 x 3 75 x 0 75 Power 2 AAA Batteries included CEE si 0 45 Ib 0 51 Ib 0 45 Ib
3. Wait until the LCD displays 0 0 then press and HOLD the MODE key for 3 seconds The LCD will display CAL You can now release the MODE key 3 Press MODE key again the LCD will display CAL and 1000 0 4 Add 1000g calibration weight the display will show PASS and return to normal weighing mode 5 Put away the calibration weight and press ON OFF to turn off the scale Finished Repeat if necessary V TROUBLESHOOTING primary reasons for inaccuracy or malfunction are low batteries incorrect calibration overload or operating on an unstable surface Please keep this in mind and maintain and operate your scale properly This scale is a precise instrument and must be handled with the utmost care and caution Display Elimination of errors Nothing Battery Symbol lo or 88888 Change the batteries OUE2 Recalibrate the scale as shown above EEEEE You are overloading the scale Remove the excessive load immediately LLLLL The delicate weighing load cells have been damaged by misusing the scale i e it was shocked dropped or overloaded You can try recalibrating the scale If the load cell has not been damaged too much it will work again after recalibration UNST Use the scale in a more stable position Specifications Model Blade 400 Blade 550 Blade 1000 Blade 50 400g 550g 10009 509 14 1102 19 4002 35 2702 1 76402 12 8602 17
4. scale on a stable vibration free surface 1 OPERATION Place Scale on a horizontal flat surface 1 Press ON OFF key 2 Wait until 0 0 is displayed 3 Put the object s on the weighing platform 4 Using the MODE key you can switch between the weighing units TARE WEIGHING 1 Turn on scale as described above 2 Place the tare item on the platform 3 Press TARE and wait until 0 0 is displayed 4 Add the net weight item Ill CALIBRATION Calibration is NOT required before first use Only calibrate if scale is not weighing properly Make sure you use the correct calibration weight for your scale or the calibration will not be accurate BLADE 50 500 calibration weight BLADE 400 400g calibration weight BLADE 550 500g calibration weight BLADE 1000 See section IV Blade1000 Calibration Procedures 1 Turn ON the scale 2 Press and hold the MODE key until CAL is dis played Release the MODE key 3 Press MODE again Now the display will read CAL and the required calibration weight will flash 3 times 4 Place the required calibration weight for your scale on the center of platform Wait 3 4 seconds The LCD will display PASS 5 Remove the weight and press ON OFF to turn off the scale Finished Repeat if necessary IV BLADE1000 Calibration Procedures You will need a 1000g 1kg calibration weight 1 Turn on the scale by pressing ON OFF key 2
Download Pdf Manuals
Related Search