GlAss And dishwAshERs instAllAtion And opERAtion
Contents
1. again The display will show alternately 4 and or the remaining water quantity liter In the lower Display appears the value up to 999 liter Thousands will be shown in the upper Display Example 1586 liter Max indication 999 999 To reset the counter to pre set value push and hold 3 seconds the ON OFF button 10 7 TERMINATION OF SETTING MODE COUNTER DISPLAY Open the hood and close it again or not press any button for 10 seconds 16 AG 21590 A 09 08 11 FROST PREVENTION In case of frost or longer operation pauses e g for seasonal operations the machine must be completely drained This should be carried out by after sales service Reset for operation according to chapter 5 12 MAINTENANCE For trouble free operation we recommend you enter into a service contract with your local Service Office DERVIEE 13 TROUBLESHOOTING GUIDE TYPE OF FAILURE Poor wash result POSSIBLE CAUSE REMEDY Dishes are not clean Wash arms stiff you should be able to turn them easily by hand Take out wash arms and clean them thoroughly Check water outlet from machine to wash arms is clear Wash arm nozzles are clogged visual check Take out wash arm remove cleaning cap and rinse wash arm thoroughly until soil is removed Replace correctly Rinse arm nozzles are clogged possibly by lime deposit Remove rinse arms and decalcify them in se2. GLASS AND DISHWASHERS INSTALLATION AND AM900 OPERATION INSTRUCTIONS Starting from Serial No 8658 0001 REV 29 09 2008 AG 21590 A 09 08 Page AG 21590 A 09 08 IMPORTANT NOTES 0ccesecccccsseeccccsssseeeeceseeeeceasseeeeseceseeeeees 4 2 INSTALLATION 5 Pale Location 5 2 2 Converting to Corner Operation sosirea 5 2 3 Electrical CONNECTION cenene 6 2 4 Water connection cccccccccccccessssseeeeceeeccesessseeeeeeeecesstsateeeeseesessnsaes 6 2 5 Drain connection cccccccccecccesssseeeeceeececsessseeeeceeeceesnsseeeeeeeeeetsnsaes 6 3 CONNECTING A POWDER OR SOLID DETERGENT DISPENSER 7 A CONTROLS 2 2 8 5 START UP 9 5 1 Detergent 9 5 2 Priming the SUCtION NOSES nnani 9 5 3 Softener only Option 10 6 OPERATION siccisicacctesdiadeheaccua dnain daaa E aaaeaii 11 Ok 11 6 2 1 6 3 Program Selection asessgnnnunnansnnnnnnnnn innnan 12 7 SWITCH OFF AND CLEANING THE MACHINE 13 71 SWECO Eea a aaa a Aaaa Aa SarSan 13 Cleaning 13 7 3 22 13 8 PREVIEW OF TEMPERATURES 14 9 vaudavenvaudavedvadesuauvuneees 1
3. 0 s 0 2 2 g l appears Adjustment should be done in accordance with chemical suppliers recommendations as m Oo ADJUSTMENT OF WATER HARDNESS With optional softener only To adjust the softener to the local water hardness obtain details from local water authority Push Program button repeatedly until in the upper Display HO2 appears Push ON OFF button repeatedly until the required value 1 4 will be displayed up to 9 2 10 to 18 eh 19 to 26 4 27 to 38 eh water hardness eh Clark AG 21590 A 09 08 15 SETTINGS AND COUNTER VALUES 10 4 CYCLE COUNTER Push Program button again The display will show alternately P or the number of wash cycles Inthe lower Display appears the value up to 999 Thousands will be shown in the upper Display Example 1023 wash cycles Max indication 999 999 10 5 WATER CONSUMPTION COUNTER Push Program button again The display will show alternately or the water consumption liter In the lower Display appears the value up to 999 liter Thousands will be shown in the upper Display Example 10217 liter Max indication 999 999 10 6 REMAINING WATER QUANTITY COUNTER FOR EXTERNAL WATER TREATMENT Only available if activated in service mode 518 The capacity liter of the water treatment has to be stored via C79 80 Push Program button
4. 4 10 SETTINGS AND COUNTER VALUES 15 10 1 Adjustment of detergent dosage Quantity 15 10 2 Adjustment of rinse aid dosage Quantity 15 10 3 Adjustment of water hardness cccssssccccsscseeseeseeesssseeesseseeeess 15 16 10 5 Water CONSUMPTION COUNTED 16 10 6 Remaining water quantity counter for external water treatment 16 10 7 Termination of setting mode counter display 16 11 FROST PREVENTION 17 12 MAINTENANCE 17 13 TROUBLESHOOTING GUIDE 17 1 IMPORTANT NOTES GB Use in Accordance with Regulations This machine is exclusively to be used to wash ware such as plates cups glasses cutlery trays etc Do not use for electrically heated cooking and heat conservation appliances Safety Never hose down the machine safe operation of the machine The Attention symbol is shown beside instructions that are essential for the Please read these passages thoroughly Liability Installations and repairs which are carried out by non authorized technicians or the use of other than original spare parts and any technical alterations to the machine may affect the warranty set out in the standard conditions of sale Machine noise l
5. SUCTION HOSES We recommend the manual hose priming as follows ATTENTION The machine has to be switched off Open the hood Push Stop button 3 and Program button simultaneously until the upper Display shows CH1 Push Program button repeatedly until d is displayed Close the hood In the upper Display appears SF1 in the lower START UP 5 2 1 DETERGENT SUCTION HOSE Pushing the ON OFF button activates the hose priming for 60 seconds Each cycle can be interrupted by pushing the ON OFF button again 5 2 2 RINSE AID SUCTION HOSE Push the Program button In the upper Display appears 5 2 in the lower Pushing the ON OFF button activates the hose priming for 360 seconds Each cycle can be interrupted by pushing the ON OFF button again 5 2 3 TERMINATION OF HOSE PRIMING Open hood and close it again or do not press any button for 10 seconds 5 3 SOFTENER only on option For the first run the softener has to be filled with regeneration salt and potable water Filling the salt reservoir with cleaning agent will damage the water softener Open the hood Unscrew the softener lid and fill the softener with 2 kg of Granular regeneration salt do not use salt tablets Fill up the softener with potable water only at the first run Clean seal and rim of softener lid carefully before closing the li
6. al demineralisation is strongly recommended Machines without softener Connect to soft and if possible warm water up to 4 Clark 0 5 mmol l max 60 C Machines with softener Connect to warm water max 60 C if possible Line flow pressure 0 5 10 bar Important the line flow pressure must not be less than 0 5 bar If the line flow pressure is above 10 bar provide pressure reducer at source Connect the union nut 3 4 of the water supply hose to the site shut off valve Do not kink or cut the supply hose If an extended supply hose is required use one of the same specifications as the original 2 5 DRAIN CONNECTION Connection between machine and site drain must not exceed max height of 0 75 m Do not place the drain hose loosely on the floor the hose could be rubbed through Fix it at site Do not kink the drain hose AG 21590 A 09 08 3 CONNECTING A POWDER OR SOLID DETERGENT DISPENSER Must be carried out by an authorized technician according GB to the local and national codes Tank must be drained Switch off main switch or unplug Remove front panel and the left hand or right hand side panel according to requirement on site Lift up control box and turn it to front Break out perforated disk at the tank panel either at the right or left side Drill a hole through the inner tank wall appropriate to the required connection diameter Screw up tigh
7. d Close lid and tighten Adjust the water hardness according to chapter 10 3 When the Salt indicator illuminates during operation the softener has to be refilled with regeneration salt There will be a slight delay before salt light goes out after refill 10 AG 21590 A 09 08 6 OPERATION AG 21590 A 09 08 PREPARATION Check correct position of rack guide wash rinse arms and strainers Open shut off valve Switch on main switch or put the plug in Check level of detergent and rinse aid containers Close hood and push the ON OFF button 1 tank will be filled The ON OFF button flashes green during fill and heating cycle This process can take several minutes When the button changes to green steady burning light machine is ready for operation Place glasses and cups face downwards into the rack Remove any food debris before loading plates into rack Spray off greasy food soil RUN Put rack into the machine and close the hood The ON OFF button flashes green wash cycle is running As soon as the ON OFF button changes to steady green light the wash cycle is finished Open the hood and take out rack Allow dishes to dry for 1 minute approx OPERATION 12 To avoid heat loss lower hood to Stand By position between wash cycles PROGRAM SELECTION The machine is operating automatically with standard cycle time If needed it is po
8. ervice Pressure transmitter rinse booster defective Call the after sales service Pressure transmitter tank defective Call the after sales service OTHER INDICATIONS Moving light point in the upper display Softener regeneration active only with built in softener 14 AG 21590 A 09 08 10 SETTINGS AND COUNTER VALUES ATTENTION The machine has to be switched off Open the hood If the hood will be closed or if no button is pressed for 10 seconds the indicator automatically switches off and the new settings will be saved Therefore the setting procedure can be interrupted at any time 10 1 ADJUSTMENT OF DETERGENT DOSAGE QUANTITY Push Stop button und Program button simultaneously until in the upper Display 1 appears In the lower Display appears e g 8 pre adjusted value of the detergent dosage time 8 s 2 0 g l To adjust the detergent dosage time push ON OFF button 1 repeatedly until the desired value 0 50 s 0 15 4 g appears Adjustment should be done in accordance with chemical suppliers recommendations ADJUSTMENT OF RINSE AID DOSAGE QUANTITY Push Program button again In the upper Display appears 2 In the lower Display appears e g 7 0 pre adjusted value of the rinse aid dosage time 7 0 s 0 31 g adjust the rinse aid dosage time push ON OFF button repeatedly until the desired value 0 5
9. evel The machine noise level is lt 70 dB A 4 AG 21590 A 09 08 2 INSTALLATION LOCATION Rear wall clearance not required For corner installation lateral clearance of 107 mm is required For free standing installation the optional rear panel has to be installed Level machine by turning the feet Distribute machine weight equally onto all feet 2 2 CONVERTING TO CORNER OPERATION Depending on direction of operation the guide rails may need to be adjusted to suit the direction of operation see arrows Unscrew the guide rail in front Refit guide rail at right angle according to the direction of operation AG 21590 A 09 08 INSTALLATION Racu II SS 2 3 ELECTRICAL CONNECTION Must be carried out by an authorized technician according to the local and national codes The electrical supply shall comply with the name plate data Line fuses and cable cross section shall comply with the requirements A cut off device shall be provided to connect the supply cord isolating switch or accessible plug device According to EN 60 335 the appliance must be connected to an equipotential conductor The connecting screw 7 is located beside the cable inlet 2 4 WATER CONNECTION Must be carried out by an authorized technician according to the national and local codes The machine must be operated with potable water For water with an extremely high mineral content an extern
10. icy of HOBART specifications are subject to change without notice Printed in Germany AG 21590 A 09 08 PC
11. nd rinse arms AG 21590 A 09 08 13 8 PREVIEW OF TEMPERATURES Press and hold 3 seconds the Program button 2 until the actual temperatures C are displayed top rinse bottom wash The indicators go out 10 seconds after releasing the Program button Permanent temperature display can be activated on request by the service technician According to the fault an error code will be shown in the upper display see table below Please report the error code to the service technician POSSIBLE CAUSE MEASURES Drain hose blocked Restart drain cycle Clean drain hose if necessary Rinse booster heating defective Call the after sales service OPTION External demineralisation cartridge depleted Replace cartridge Salt deficiency Refill the softener with granular regeneration salt only with built in softener The Service indicator is illuminated and POSSIBLE CAUSE MEASURES Shut off valve is closed Open shut off valve at site and switch on machine again Fill valve or fill system defective Call the after sales service Tank strainer not correctly positioned Put strainer correctly in place Drain hose blocked Clean drain hose and restart drain cycle Fill system or drain system defective Call the after sales service Temperature probe rinse booster defective Call the after sales service Temperature probe tank defective Call the after sales s
12. parate container Detergent concentration is too low or too high Check setting of detergent concentration See also operating instructions point 10 1 Coarse strainer soiled Take out strainer empty and clean it Fine strainer soiled or obstructed by lime Take out fine strainer If heavily soiled soak in a vinegar solution Then clean it thoroughly until the pores are free Cleaning is to be done daily see operating instructions Wrong program selected for heavily soiled dishes Select program with longer wash cycle Dishes or glasses do not dry properly AG 21590 A 09 08 Rinse aid concentration too low Increase concentration See also operating instructions point 10 2 Dishes still greasy 1 Detergent concentration too low increase see instructions 2 Check if detergent is appropriate If not choose a stronger one 3 Drain soiled water and refill machine Check pre scrapping procedure Rack is not suitable for type of dishes sloping Use appropriate racks to create a sloping position which allows water to drain away from cavities Dishes stay too long in the machine at the end of program Take out dishes as soon as cycle is completed to enable them to dry TROUBLESHOOTING GUIDE TYPE OF FAILURE Poor wash result POSSIBLE CAUSE REMEDY Stripes and staines on dishes or glasses Rinse aid concentration too high Reduce quantit
13. ssible to select a shorter or longer program To show the present program push the Program button before starting the wash cycle To change the program push the Program button again 01 Short cycle for light medium soiled dishes and glassware P 02 Standard cycle for medium heavy soiled dishes 03 Long cycle for dried on soiling and containers The machine continues with the chosen cycle time until it is switched off or another program is chosen AG 21590 A 09 08 7 SWITCH OFF AND CLEANING THE MACHINE 7 1 SWITCH OFF Close the hood Push and hold min 3 seconds the ON OFF button 1 The button flashes green during the drain cycle NOTE During the drain cycle the interior of the machine is cleaned automatically A final inspection is recommended to remove any food debris When the ON OFF button goes off Switch off main switch or unplug and close the shut off valve 7 2 CLEANING DAILY To clean the machine do not use any chloric acidic or abrasive products and no metallic brushs Open hood and take out rack guide Take out strainers and flush Please ensure that food debris does not enter pump intake Clean interior of the machine Put strainers and rack guide back into place Leave hood open for ventilation 7 3 CLEANING WEEKLY Take out rack guide Loosen the retaining screws A by turning them counter clockwise Take out and clean wash a
14. tly the dosing connection with tank wall Connect the plug A of the wire harness with the dosage pump max 100 VA Close control box and put panels back into place Switch on main switch at site or put the plug in Dispenser adjustment see chapter 10 1 CONDUCTIVITY PROBE Conductivity probe should be installed at the flat part of tank bottom see The hole size should be appropriate the conductivity probe Important Remove drilling chips thoroughly to prevent corrosion AG 21590 A 09 08 7 4 CONTROLS T Machine ON OFF 2 Program button Pushing this button switches the machine on By pushing and holding 3 seconds this button the drain and self cleaning cycle starts At the end of the cycle the machine switches off automatically After switch off the machine is not voltage free Furthermore the button illuminates to indicate the mode of the machine GREEN flashing Machine is filling and heating Wash cycle is running Machine is draining switches off GREEN permanent Machine is ready for operation By pushing this button it is possible to select between different preset programs according to the model and equipment The program no e g 2 will be shown in the Display 3 Stop button In case of operating error or faults it is possible to switch off the machine immediately without the drain cycle by pushing this button After s
15. witch off the machine is not voltage free Display 5 Display e g temperature indication Wash C see chapter 8 e g temperature indication Rinse C see chapter 8 6 Salt required Indicating the need for regeneration salt to be added Only with built in softener 7 Service indicator Indicating that the machine has a fault see chapter 9 AG 21590 A 09 08 5 START UP AG 21590 A 09 08 5 1 DETERGENT RINSE AID Use only commercial detergent and rinse aid Please pay attention to the manufacturers safety instructions The dosing pumps can operate to a maximum head height of 1 5 m Do not confuse the containers 5 1 1 DETERGENT Do not use any acidic detergent products with the built in detergent pump The ph value has to be higher than 7 Place the suction hose into the external detergent container Fill the suction hose according to chapter 5 2 5 1 2 RINSE AID Place the suction hose blue marking into the external rinse aid container Fill the suction hose according to chapter 5 2 5 1 3 CHANGING THE TYPE OF DETERGENT RINSE AID Before changing to a different product type even from the same supplier the suction hoses must be rinsed thoroughly with fresh water procedure as described under 5 2 Otherwise the mixing of different types of chemicals will cause crystallisation which may result in a malfunction of the dosing pump 5 2 PRIMING THE
16. y see instructions Hard water or high mineral content Check water quality Obtain details from local water authority Recommended values Ideal degree of hardness is 4 Clark Ideal conductivity value for glasses is 150 uS cm and for dishes max 400 5 Rack is not suitable for type of dishes sloping Use appropriate racks to create a sloping position which allows water to drain away from cavities Insufficient rinse aid concentration causes staines Increase quantity see instructions Machine with softener Wrong type of salt used Use only granular regeneration salt Other malfunctions Glasses are totally or partially cloudy Surface of glasses is rough and porous this is called glass corrosion This is not caused by a malfunction on the machine Replace with new glasses Glass breakages Use of inappropriate dish or glass racks Use appropriate racks Machine suddenly stops during wash program Machine is connected to a maximum power supply unit which cuts out the energy consumer at a given point or ma chine is interlocked with another energy consumer unit Connect machine separately call electrician Blown site fuse Check site fuses If no button will be pressed during 6 hours the machine switches off automatically without draining AG 21590 A 09 08 AG 21590 A 09 08 As continued product improvement is a pol
Download Pdf Manuals
Related Search