STD-403 STEP Motor driver User manual
Contents
1. FUNCTION SELECT 3123456 Pulse input mode selection SW 1 2 3 456 1C SW 3 4 ON SW 1 2 OFF 1 pulse mode 2C SW 1 2 ON SW 3 4 OFF 2 pulse mode 1C o 0 2C e e Step mode selection HALF HALF SW 5 ON 0 9 step 400step rev FULL FULLO SW 5 OFF 1 8 step 200step rev Standby current mode selection A CC SW 6 OFF automatically reduce at standby N CC SW 6 ON Not reduce at standby Factory set as 2C HALF A CC 5 CURRENT ADJUSTMENT The output current has been adjusted by factory before delivery The output current should measure by DC DC 5A Ampere meter connected in series between the terminal COM and step motor COM Aor COM to measured current value CC ADJ the SW 6 must be off To adjusted output current at standby condition The motor current is automatically reduction in this value at standby when selected A CC mode C ADJ the SW 6 must be on and the motor at 2 phase excitation condition 1 the SW 5 and SW 6 must be on and the motor at 1 phase excitation condition To adjusted output current at 1 phase excitation condition This current level is increased in the 1 phase excitation condition to help maintain the torque on intermediate steps j 319 TAILY AUTOMATION CO LTD gi STD 403 STEP Motor driver User manual 6 INPUT SIGNAL2. S Page 4 of 6 STD 403 with three input signals CW CO The CCW with two input mode select by function selection switch Pulse input mode CW CCW selection 1 Pulse input Direction input 2C CW pulse input CCW pulse input when this input is low lever the driver will turn of output current to free the step motor from excitation condition CONTROLLER STD 403 220R V CW PUS did A 20mA MAX 220R CCW DIR R A 20 220R BB CO 20mA MAX OV Signals wave T1 T2 T4 20us min T3 2us E E EE CCWIDIR L 0 0 5V ee Los cocos Laco CW PUS L 0 0 5V Ex CERTES G i ER 1 TAILY AUTOMATION CO LTD gi STD 403 STEP Motor driver User manual Page 5 of 6 7 INSTALLATION AND WIRING Requirement and Safety precautions 1 The driver should be operated in an environment that is protected from moisture corrosive gases oil mist and airborne dust metallic particles 2 The driver should be operated free from magnetic noise if not use a noise filter to minimize of electromagnetic interference 3 Normally operate under 10 C 40 Cenvironment do not block the intake exhaust ports of the driver Otherwise a fault may occur 4 Do not connect or disconnect connectors while power is applied to the driver 5 Make sure a
3. TAILY i AUTO STD pee driver an ser manua DOC NO 050330 Page 1 of 6 1 INTRODUCTION The STD 403 stepper motor driver is unipolar PWM chopper constant current regulated unit designed to operate with a wide range of step motors Manufactured by TAILY AUTOMATION Is suitable to drives 2 or 4 phase step motor the driver is high torque easy to interface and use high performance and low cost 2 SPECIFICATIONS wm 7 Half step 1 2 phase excitation Input signals CCW DIR input Current OFF input Ambient temperature 0 C 40 C Weight 0 75 kg Over temperature Over temperature protect with LED indicate j 319 TAILY AUTOMATION CO LTD gi STD 403 STEP Motor driver User manual Page 2 of 6 3 PANEL DESCRIPTION TAILY PW 2 cw 8 58 2 4 a co _ s5 10 Baz COM 6 zr P B B AC f CONNECTION PANEL SELECTION PANEL No name BESCRIPON FAGTORYSET Porma OOS 3 orenean s co Motorcurentofinoutteminas COM Stepper motor connection terminals A B B AG HOV a s cabs ipmeexisn crentadus 4 j 319 TAILY AUTOMATION CO LTD gi STD 403 STEP Motor driver User manual Page 3 of 6 4
4. ll the terminals are connected to the correct position before turn on the power 6 Make sure that the power source supplies the correct voltage and is capable of supplying the required current to the driver 7 Make sure that the driver is properly grounded Wiring diagram CONTROLLER STD 403 e PW V OH CW PUS CCW DIR STEPPING MOTOR AC 110V 10 50 60HZ j 319 TAILY AUTOMATION CO LTD gi STD 403 STEP Motor driver User manual Page 6 of 6 8 DIMENSION TAILY Qe Pw AUTO cw A _ CCW H CO J amp I S e COM N SS A H cdi B B AC AC 1 45 0 um CN ol N ST 80 134 0 80 140 0 uro G i Jeb 1 TAILY AUTOMATION CO LTD
Download Pdf Manuals
Related Search