Navodila diseqc controller a5-ANG-public
Contents
1. table below 7 ENERGY SUPPLY E Equipment has its own battery inside Ni Cd 12V 600mAh It is enough to drive satellite polar mount motor for few hours non stop When battery is low indicator will light red can be adjusted with inside trimmer resistor When external charger is connected charger will charging battery disconnected from equipment but equipment will be supplied by charger Battery will be charged with constant current of cca 60mA that method is recommended for Ni Cd battery When charging LED indicator will constantly lighting green and stop to light when charging is terminated Termination method for charging is voltage level When battery voltage will reach pre defined voltage level charging will be finished termination voltage level can be adjusted with inside trimmer resistor Aware that charging must not exceed 14 hours 8 RECEPTION OF DISEQC STRING E Universal DiSEqC controller is two way DiSEqC device It can send and receive DiSEqC strings When use it as DiSEqC monitor normally connect it with measure device i e satellite receiver and you will be able to see receiver s output strings on second line of LCD Only thing to be noted here is output voltage of measured device must be as close as Universal DiSEqC controller have it that is 18V All recepted string will be sent through RS232 COM port to PC for logging purpose SAT CONTROL 9 Want to get more Y Universal gt DiSEaC control2. Do not expose to any moisture or rain o Do not use it at low temperatures below 0 C or high temperatures above 50 C o Strokes and shocks can damage the device Avoid device from falling down to the hard floor o It is not recommended to repair it by yourself Contact your supplier if anything is wrong with the device 4 CONNECTIONS ON UNIVERSAL DISEQC CONTROLLER 4 4 1 F CONNECTORS Upper side has two F connectors for connecting equipment to DiSEqC measure device Any sent DiSEqC string will go out on these two connectors Also DiSEqC reply will be received here if two way DiSEqC communication is used Both F connectors are shorted for signal and DC supply and are totally equal One connector can be connected to i e motor LNB switcher and other can be used for purposes like signal meter analysers etc 4 2 RS232 PORT Beside F connector there is RS232 port for connection to PC Any received DiSEqC string will be sent also to RS232 port and can be seen on any terminal program on PC Use extension COM cable for connecting DB9 Female DB9 Male 2 2 3 3 5 5 Recommended program on PC is HyperTerminal included in almost all Windows environments Set configuration of program to 21x Port Settings Bits per second X patate yl Party None Fl sete FG Flow control Hardware y Restore Defaults Cancel Apply SAT CONTROL 5 Want to get more Y Universal gt gt DiSEgC contr
3. QUIPMENT CONTROL SAT CONTROL v Wantio get more Universal gt gt DiSEaC controller 3 General preCautions iii 5 4 Connections on Universal DiSEqC Controller LM e PE 4 2 RS292 poll ice ic cre PR PL ic 5 9 Charger P 6 6 Structure of meni iii tert ei et 6 6 1 COMMANG edis seme ht tre tien tette ata Sena 6 Goto degrees cet acit ni a i c eni re n a A ET nr 6 iud 6 Store location jandp pH Drive east cie eie tm da T Drive WESE 7 Switchi comm tatlve ic cete a ede diel iaia 7 Switch UNCOMMU AIVO soi aaan Ana 7 6 2 ManUall nena ctun atte n cod ie ate B e ERE Ro 7 A aaa 8 Adjust O degrees 1 nm ada 8 Adjust O degrees 2 Read eeprom d aita ect u ra a PEE prd ERE aa aia IUNCTI d M newest 8 Read ram sue ca ten oi a OR E Ure ARI aaa 9 DO MO acetone n teste tertii tenir finite itu ino tan 9 Te Energy SUpply cree eee eae o a be t ln 9 8 Reception of DISEQC string nente teen tenente nn 9 4 SAT CONTROL yy Mee Universal DiSEaC controller ARK En 4 o Universal DiSEqC Controller is low voltage device Do not connect it to some high voltage o Use checked cables for connections o For cleaning its housing use soft and not aggressive liquids o Do not leave it on the sun or by any source of heat o
4. Universal DiSEaC controller 444 USER MANUAL SAT CONTROL S CONT Want to get more L LJ L LJ LJ LJ LJ LJ LJ LJ LJ e e LJ LJ LJ LJ CONTROL DATI Wantio get more Universal DiSEqC controller 444 Satellite television is one of most favourite and popular medium in today s world But reception 36 000 km away from the sky is more technically difficult Every user must have accurate setted dish with high tech reception block and additionally complicated devices for pointing many satellites and splitting signal for more users In the earlier years of satellite TV DiSEqC Digital Satellite Equipment Control protocol was invented due to commanding between master device and all slave peripheries DiSEqC protocol uses 22 kHz signal modulated with digital PWK pulse wide keying and like that it can be transmitted by the same coax cable like satellite signal and DC supply voltage With these principe master device can command all other devices connected on the same cable in a multi drop mode real time Every technician who work on development or service for satellite devices have a need for some measurement equipment with DiSEqC generating strings And this need is introduced in this script like Universal DiSEqC controller Equipment is generator of DiSEqC strings as they are presented in original Eutelsat s document with additional manual entry and some special functions DIGITAL SATELLITE z E
5. an get current zero factor anytime you want by pressing 2nd function button Note for versions of motors without LED light emitting diode by F connectors Read eeprom This command will read value from internal storage place There motor have stored locations for all 50 satellites used when you are driving motor by location and NOT used when you are using degree commanding Eeprom also has stored some system parameters that can be checked please refer to technical script of motor SM3D22 Set wanted eeprom address and press enter Motor will give you reply of current value of address Write eeprom In this submenu values stored in eeprom can be changed Attention Do not change values unless you know what you are doing Changing values can cause inaccuracy of the motor please refer to technical script of motor SM3D22 Enter address of eeprom to be changed and press enter Enter new value in HEX format and press enter again New value is written SAT CONTROL Want o get more Universal DiSEaC controller ARK Read ram This option can read internal working ram values If you don t know meaning of addresses this submenu is unusable for you please refer to technical script of motor SM3D22 Set wanted ram address and press enter Motor will give you reply of current value of address Set mode Motors from Sat Control can work in different options Setting its mode can change working of motor as described in
6. er to get stored satellite controlling motor by location Note Default frame byte is OXE0 and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Stop motor Send command for unconditional stop Note Default frame byte is OXE0 and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Want to get more Universal DiSEaC controller KKK Drive east Command will move a polar mount motor to east direction for defined number of impulses What angle it will be it depends on resolution of the motor Note Default frame byte is OxEO and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Drive west Command will move a polar mount motor to west direction for defined number of impulses What angle will that be it depends on resolution of the motor Note Default frame byte is 0XE0 and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices S
7. ler Dear customer If you have not been able to put the system into operation or have problems installing it call the Technical Assistance phone as indicated on the first and the last pages or write to us at support sat control si We will be pleased to provide you with further information If you have installed the system to your satisfaction we congratulate you Your manufacturer SAT CONTROL d o o Manufacturer SAT CONTROL d o o Pozenik 10 SI 4207 CERKLJE SLOVENIA Phone 386 4 281 62 00 Fax 386 4 281 62 12 www sat control net sales sat control si All rights reserved Copying is forbidden The product is patented Made in EU Slovenia SAT CONTROL Wantio get more x SAT CONTROL Se Want to get more wr
8. o setup polar mount motors made by Sat Control d o o It also uses PWK modulation on the same base frequency but string content is totally different communication with motor is two way and fully secured from data collision to achieve the best regularly transmittion Menu allow user to get into motor s software and setup its settings and on line check behaviour of the motor That option is best way to control a motor and its working Adjust 0 degrees 1 Submenu can adjust motor scale of degrees by setting its zero degrees If the motor is not accurate when you are pointing it with GotoX degrees you must adjust it in this submenu By moving number E or W and pressing enter motor will do the move Command for shift and command for goto zero degrees will be sentto the motor and motor will move to its new zero position If new zero position equal to real zero motor is adjusted Otherwise repeat unless you get real zero degrees Note for versions of motors without LED light emitting diode by F connectors Adjust 0 degrees 2 Submenu has the same purpose like upper submenu but it works in two way communications When enter in this submenu equipment will get current value of zero factor from the motor Now you can change it as you want and press enter to send it in the motor Motor will than move to its new zero position If new zero position equal to real zero motor is adjusted Otherwise repeat unless you get real zero degrees You c
9. oller b 5 CHARGER PLUG Use this plug to charge internal battery See chapter Energy supply Charger s voltage is around 17V a 6 STRUCTURE OF MENU 6 1 COMMAND This menu contains the most useful DiSEqC commands for driving motor and signal switchers For more detailed description of these commands please see Eutelsat s DiSEqC bus specification Goto degrees Send commands for driving polar mount motor to wanted degrees Motor will turn to relative angle If you are pointing satellite geometrical calculation according to your geo position must be done This submenu is suitable for GotoX Usals controlling of motor Note Default frame byte is OxEO and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Goto location Send commands for calling stored satellite location Motor will move a dish to stored location that belongs to called number Location is stored in motor Note Default frame byte is OxEO and address byte is 0x31 for motors as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Store location When satellite is pointed and signal is on maximum with this command you can store location of dish to some location number Note receiver should call that numb
10. witch commutative Send commands for DiSEqC 1 0 switchers Signal switcher will switch HF connection to the selected input Usually this type supports maximum four inputs Note Default frame byte is OxEO and address byte is 0x10 for switchers as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices Switch uncommutative Send commands for DiSEqC 1 1 switchers Function is the same like in commutative switchers but number of inputs is extended to max 16 some application have 32 in combination with commands from Switch commutative menu Note Default frame byte is OxEO and address byte is 0x10 for switchers as refer in original DiSEqC specifications With button 2nd function this two bytes can be changed but aware that this can cause unworking of DiSEqC devices 6 2 MANUAL This menu is suitable for manual entry of DISEqC command You can put into line any bytes you want the only restriction is that number of bytes must be greater than 3 bytes and smaller than 7 bytes Also half of byte is not allowed Than entered string will be send Device will not check if string is in DiSEqC specification or not Press button lt q to clear display SAT CONTROL Y Want to get more Universal gt gt DiSEaC controller 6 3 SPECIAL This menu is NOT by DiSEqC specification Its purpose is t
Download Pdf Manuals
Related Search