Home
LED Par 64 Aircraft
Contents
1. Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C 05 Link the units as shown in figure 4 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units O6 Supply electric power Plug electric mains power cords into each unit s IEC socket then plug the other end of the mains power cord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set up and connected properly Multiple Aircrafts DMX Set Up Fig 03 Note Link all cables before connecting electric power Ordercode 30743 LED Par 64 Aircraft Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX 512 controller or to run synchronized shows on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support Important Fixtures on a serial data link must be daisy chained in one single line To comply with the EIA 485 standard no more than 30 devices should be connected on one data link Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may res
2. DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address which is the first channel from which the Aircraft will respond to the controller Please note when you use the controller the unit has 3 channels When using multiple Aircrafts make sure you set the DMX addresses right Therefore the DMX address of the first Aircrafts should be 1 001 the DMX address of the second Aircraft should be 1 3 4 004 the DMX address of the third Aircraft should be 4 3 7 007 etc Please be sure that you don t have any overlapping channels in order to control each Aircraft correctly If two or more Aircrafts are addressed similarly they will work similarly Controlling After having addressed all Aircraft fixtures you may now start operating these via your lighting controller Note After switching on the Aircraft will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will show NO DMX Signal he problem may be The XLR cable from the controller is not connected with the input of the Aircraft The controller is switched off or defective the cable or connector is detective or the signal wires are swapped in the input connector Note It s necessary to insert a XLR termination plug with 120 Ohm in the last fixture in order to ensure proper transmission on the DMX data link To unlock the display press and hold any of
3. MANUAL N O lt LLI LED Par 64 Aircraft LED Par 64 Aircraft Table of contents Wo reu dg ene2 EMT 2 OOo elermilnmaollohs mmm 4 OO 4 RSI 6 6 D SCIDION OP Me COMICS Tn IT N E E A E E A AEE E AE E AEA 8 BAI RON 8 ISO 9 9efTUDOnadOperoalionm EE KK 5 9 Wedel ese m ER 7 One Alrcrotr BUNN aS ela Eom 9 One Alrerarr Manual DImmIESFOEPEIONOP scies teseiessieceasebetotusoiesedesebeteiesebeveteYodesa Luss iocetasetadeiuseiecsisaetorsieveces 9 PAU Ole Aircrafis DMA EGG 10 oo 1 1 1 COOP EL 12 on 12 we 12 NUCE EE 13 We 14 EE 14 VN OMIA 9 rca etouiote votre ot u u E 14 de DIR ON OR Re a a EE EA T E AEA 14 14 5 Delay MOE Ne 15 MB Wee WC ICI vests mtm 15 TINK IOC CR a E I 15 cv dere nn 15 II 16 ENGINE 16 CO MORE de Ua de 16 NIOH 16 MaiMenan E RTT 17 SEN 17 MEO UD ISS MO OWING sareren E m 18 regwuwcTs6ecillcarianm EE TO ERREUR 20 Ordercode 30743 1 Show 7 a LED Par 64 Aircraft Warning For your own safety please read this user manual carefully before your initial start up Unpacking Instructions Immediately upon receiving this product carefully unpack the carton and check the contents fo ensure that all parts are present and have been received in good condition Notify the dealer immediately and retain packing material for inspection if any pa
4. the installation place is blocked and staying in the area is forbidden The LED Par 64 Aircraft can be mounted in a hanging position Fig Above or Upright Fig Below using the support brackets Mounting the LED Par 64 Aircraft with a clamp or any other mounting bracket is recommended depending on the requirements of your application The LED Par 64 Aircraft can be placed on a flat stage floor or mounted to any kind of truss by a clamp Improper installation can cause serious damage to people and property Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place International EU Cable UK Cable US Cable Pin ct BROWN RED YELLOW COPPER FASE s boue BLUE BLACK SILVER _ IE NULL s YELLOW GREEN GREEN GREEN EARTH Make sure that the device is always connected properly to the earth Improper installation can cause serious damage to people and property Ordercode 30743 5 Show 23 a LED Par 64 Aircraft A Return Procedure A Returned merchandise must be sent prepaid and in the original packing call tags will not be issued Package must be clearly labeled with a Return Authorization Number RMA number Products returned without an RMA number will be refused Highlite will not accept the returned goods or any responsibility Call Highlite 0031 455667723 or mail aftersaleseghighlite nl and request an
5. RMA prior to shipping the fixture Be prepared to provide the model number serial number and a brief description of the cause for the return Be sure to properly pack fixture any shipping damage resulting from inadequate packaging is the customer s responsibility Highlite reserves the right to use its own discretion to repair or replace product s As a suggestion proper UPS packing or double boxing is always a safe method fo use Note If you are given an RMA number please include the following information on a piece of paper inside the box 01 Your name 02 Your address 03 Your phone number 04 A brief description of the symptoms Claims The client has the obligation to check the delivered goods immediately upon delivery for any short comings and or visible defects or perform this check after our announcement that the goods are at their disposal Damage incurred in shipping is the responsibility of the shipper therefore the damage must be reported to the carrier upon receipt of merchandise It is the customers responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping Transportation damage has to be reported to us within one day after receipt of the delivery Any return shipment has to be made post paid at all times Return shipments must be accompanied with a letter defining the reason for return shipment Non prepaid return shipments will be refused unless otherwise agree
6. ams 01 Fasten the effect light onto firm trussing Leave at least 1 meter on all sides for air circulation Always use a safety cable ordercode 70140 70141 Plug the end of the electric mains power cord into a proper electric power supply socket O4 When the Aircraft is not connected by a DMX coble it functions as a stand alone device Please see page 14 for more information about the built in programs One Aircraft Manual Dimmer Operation 01 Fasten the effect light onto firm trussing Leave at least 1 meter on all sides for air circulation Always use a safety cable ordercode 70140 70141 O3 Plug the end of the electric mains power cord into a proper electric power supply socket When the Aircraft is not connected by a DMX cable it functions as a stand alone device Please see page 14 for more information about the manual dimmer control Ordercode 30743 9 Show 23 a LED Par 64 Aircraft Multiple Aircrafts DMX Control 01 Fasten the effect light onto firm trussing Leave at least 1 meter on all sides for air circulation 02 Always use a safety cable ordercode 70140 70141 O3 Plug the end of the electric mains power cord into a proper electric power supply socket O4 Use a 3 p XLR cable to connect the Aircrafts and other devices Pin 1 GND screen Pin 1 GND screen Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C
7. cloth Do not use alcohol or solvents The front panel will require weekly cleaning as smoke fluid tends to build up residues reducing the light output very quickly Do not immerse in liquid Please clean internal components once a year with a light brush and vacuum cleaner Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power The operator has to make sure that safety relating and machine technical installations are to be inspected by an expert after every year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are to be inspected by a skilled person once a year The following points have to be considered during the inspection 01 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 02 There may not be any deformations on housings fixations and installation spots 03 Mechanically moving parts like axles eyes and others may not show any traces of wearing 04 The electric power supply cables must not show any damages or material fatigue Replacing a Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the dir
8. d With this menu you can set your desired speed of the built in programs ColSpeed 01 Press the MODE button on the device until the display shows O2 Press the Up Down buttons to choose 16 different speed settings 1 is slowest 16 is fastest and sound controlled 3 Dimmer Warm White With this menu you can set your desired dim value ColSet 01 Press the MODE button on the device until the display shows 02 Press the Up Down buttons to choose 255 different dimmer settings 4 Display Backlight DispPerm 01 Press the MODE button on the device until the display shows 02 Press the Up Down buttons if you want the backlight On or Off 03 If you choose Off the LCD display will dim after 10 seconds The display will be locked and the 3 menu buttons will not function 04 To unlock the display press and hold any of the 3 menu buttons for 7 seconds The display will light Up and you are able to change your settings Ordercode 30743 E LED Par 64 Aircraft 5 Delay Mode With this menu you can set your desired backlight RampMode 01 Press the MODE button on the device until the display shows El O2 Press the Up Down buttons to choose 4 different delay modes O is no delay A is the longest possible delay 6 DMX Mode 1 Channel With this menu you can set your device to a 1 Channel DMX Mode DMX 1CH 01 Press the MODE button on the device until the display shows O2 Press the Up Down buttons to if you change the DMX chann
9. d in writing Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice After this period complaints will not be handled anymore Complaints will only then be considered if the client has so far complied with all parts of the agreement regardless of the agreement of which the obligation is resulting Ordercode 30743 6 Show 7 a LED Par 64 Aircraft Description of the device Features The Showtec LED Par 64 Aircraft is a LED parcan with high output and great effects Ordercode 30743 7 Show 7 a Old school effect back to life with all advantaged of the new technologies Due to the 3 lenses and powerful 18x 3W LEDs it creates a very narrow warm white beam just like the aircrafts we used to know Because of LED and DMX technology there is no need for heavy dimmer racks and difficult cabling Another advantage is that each aircraft can be programmed separately to create even more dynamic effects Solid housing a heavy duty double bracket and Powercon in amp output to fulfill all high demanding rental needs Output Distance 100m LED Quantity 18 x 3W WW Refreshrate 400Hz Dimmer 0 100 Strobe 0 20Hz Beam Angle 3 On Board 2x8 Character Display DMX control via standard DMX controller Control DMX 512 Built in Programs Manual DMX personality 1 2 3 Channel Input Voltage 100 240V AC 50 60Hz Power consumption 60W at full ou
10. ections below to do SO 01 Unplug the unit from electric power source O2 Insert a screwdriver into the slot in the fuse cover Turn the screwdriver to the left at the same time gently push a bit Turn and Push The fuse will come out O3 Remove the used fuse If brown or unclear it is burned out 04 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details Ordercode 30743 LED Par 64 Aircraft Troubleshooting No Light This troubleshooting guide is meant to help solve simple problems If a problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas as the power supply the LED the fuse 01 Power supply Check that the unit is plugged into an appropriate power supply The LEDs Return the Aircraft to your Showtec dealer The fuse Replace the fuse See page 17 for replacing the fuse 04 If all of the above appears to be OK plug the unit in again If you are unable to determine the cause of the problem do not open the Aircraft as this may damage the unit and the warranty will become void O6 Return the device to your Showtec dealer No Response to DMX Response Su
11. efective fixture disturbing the link Inspect connections and cables Correct poor connections Repair or 1O M Rc Insert termination plug in output jack of the last fixture on the link O oeoeoeoeoooPo X One of the fixtures is defective and disturbs data transmission on the link Bypass one fixture at a fime until normal operation is regained unplug both connectors and connect them directly together Have the defective fixture serviced by a qualified technician 3 pin XLR Out on the fixtures does not match pins 2 and 3 reversed Install a phase reversing cable between the fixtures or swap pin 2 and 3 in the fixture that behaves erratically Allow fixture to cool Clean fan Make sure air vents at control panel and front lens are not blocked Turn up the air conditioning Disconnect fixture and return to your dealer The power supply settings do not match local AC voltage and Disconnect fixture Check settings and correct if necessary LED Par 64 Aircraft P
12. el You can choose 512 different DMX addresses 7 DMX Mode 2 Channels With this menu you can set your device to a 2 Channel DMX Mode DMX 2CH 01 Press the MODE button on the device until the display shows 02 Press the Up Down buttons to if you change the DMX channel You can choose 512 different DMX addresses 8 DMX Mode 3 Channels With this menu you can set your device to a 3 Channel DMX Mode DMX 3CH 01 Press the MODE button on the device until the display shows 02 Press the Up Down buttons to if you change the DMX channel You can choose 512 different DMX addresses Ordercode 30743 LED Par 64 Aircraft DMX Channels 1 Channel Mode Channel 1 Dimmer intensity E Oe AL s NH 1 255 From black to brightest K 2 Channel Mode Channel 1 Dimmer intensity Oe s 12299 From black to brightest 00 E Q 20 CUYe0 21 40 CUYe 1 41 00 CUYe 2 muuiiuuuusuuiuuujujjjuuiuuuuuie E 61 80 CUYe3 81 100 Curve 4 3 Channel Mode Channel 1 Dimmer intensity Q 20 CUYe0 d E 21 40 CUYe 1 41 00 CUYe 2 d K 61 80 CUVE S 81 100 Curve 4 Ordercode 30743 LED Par 64 Aircraft Maintenance The Showtec LED Par 64 Aircraft requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Wipe the front glass panel clean with glass cleaner and a soft
13. evice has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature If your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service For adult use only Movinghead must be installed out of the reach of children Never leave the unit running unattended Never attempt to bypass the thermostatic switch or fuses For replacement use fuses of same type and rating only The user is responsible for correct positioning and operating of the LED Par 64 Aircraft The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device This device falls under protection class Therefore it is essential to connect the yellow green conductor fo earth During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Repairs servicing and electric connection must be carried out by a qualified Technician WARRANTY Till one year after date of purchase LED Par 64 Aircraft CAUTION Eyedamages Avoid looking directly into the lightsource N meant especially for epileptics Operating Determinations This device is n
14. hort intervals as this would reduce the device s life Do not touch the device s housing bare handed during its operation housing becomes very hot Allow the fixture to cool for at least 5 minutes before handling Do not shake the device Avoid brute force when installing or operating the device Only use device indoor avoid contact with water or other liquids Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Only operate the device after having familiarized with its functions Avoid flames and do not put close to flammable liquids or gases Always keep case closed while operating Always allow free air soace of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used or before cleaning Only handle the power cord by the plug Never pull out the plug by tugging the power cord Make sure that the device is not exposed to extreme heat moisture or dust Make sure that the available voltage is not higher Than stated on the rear panel Make sure that the power cord is never crimped or damaged Check the device and the power cord from time to time If the lens is obviously damaged it has to be replaced So that its functions are not impaired due to cracks or deep scratches If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating If the d
15. ot designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surtace must be more than 1 meter The maximum ambient temperature ta 40 C must never be exceeded The relative humidity must not exceed 50 76 with an ambient temperature of 40 C If this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging trussing and all other safety issues Do not attempt the installation yourself Always let the installation be carried out by an authorized dealer Ordercode 30743 4 Show 7 lt m n LED Par 64 Aircraft Procedure e lf the projector is lowered from the ceiling or high joists professional trussing systems have to be used e Use aclamp to mount the projector with the mounting bracket to the trussing system e The projector must never be fixed swinging freely in the room e The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging Or servicing the projector always make sure that the area below
16. roduct Specification MoGel i stowtec LED Par 64 Aireraft oo B Input Voltage 100 240 MAC d Continuous Power 60W mox at FUI OUTDUT E FUSE c AA OO Ve _ Dimensions s LA03X262 x 262 mm EXWXxH Weight o 8 72 KQ miususuuiluuisijuiuisguiuujujjuusg uuue Operation and Programming d signal pin OUT pin T earth pin 2 pin 3 a Set Up and Addressing LED Control panel DMX Channels t A D d a signalinput O N XE f male 0o i signal output O N XER female 00o s e Due to the 3 lenses and powerful 18x 3W LEDs it creates a very narrow warm white beam just like the aircrafts we used to know e Another advantage is that each aircraft can be programmed separately to create even more M dynamic effects iii e Solid housing a heavy duty double bracket and Powercon in amp output to fulfill all high demanding rental needs Design and product specifications are subject to change without prior notice CC Website www Showtec info Email service highlite nl Ordercode 30743 LED Par 64 Aircraft Ordercode 30743 2014 Showfec
17. rts appear damaged from shipping or the carton itself shows signs of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Your shipment includes e Showtlec LED Par 64 Aircraft with Powercon powercable 1 5m e User manual LED Expected Lifespan LEDs gradually decline in brightness over time HEAT is the dominant factor that leads fo the acceleration of this decline Packaged in clusters LEDs exhibit higher operating temperatures than in ideal or singular optimum conditions For this reason when all color LEDs are used af their fullest intensity life of the LEDs Is significantly reduced If improving your lifesoan expectancy is of a higher priority place care In providing for lower operational temperatures This may include climatic environmental and the reduction of overall projection intensity CAUTION N Keep this device away from rain and moisture Unplug mains lead before opening the housing Safety Instructions Every person involved with the installation operation and maintenance of this device has to e be qualified e follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused b
18. spect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 01 Check the DMX setting Make sure that DMX addresses are correct 02 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 03 Determine whether the controller or light effect is at fault Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician See next page for more problem solving Ordercode 30743 LED Par 64 Aircraft 2 Problem Probable cause s Remedy One or more fixtures are completely dead Check that power is switched on and cables are plugged in Fixtures reset correctly but all respond erratically or not at all to the controller Fixtures reset correctly but some respond erratically or not at all to the controller No light or lamp cuts out intermittently 9 pin XLR Out of the controller does not match XLR Out of the first fixture on the link i e signal is reversed Poor data quality Ordercode 30743 Install a phase reversing cable between the controller and the first fixture on the link Check data quality If much lower than 100 percent the problem may be a bad data link connection poor quality or broken cables missing termination plug or a d
19. the 3 menu buttons for 7 seconds The display will light up and you are able to change your settings Ordercode 30743 2 LED Par 64 Aircraft Menu Overview ColProgr UP DOWN ColProgr Progr 1 Progr 4 ColSpeed UP DOWN ColSpeed Speed 1 Speed 16 UP DOWN ET WW 255 DispPerm UP DOWN DispPerm On Off MODE RampMode UP DOWN RampMode Delay 0 Delay 4 DMX 1CH UP DOWN DMX 1CH DMX 1 DMX 255 DMX 2CH UP DOWN DMX 1CH DMX 1 DMX 255 DMX 3CH UP DOWN DMX 1CH DMX 1 DMX 255 The LED Par 64 Aircraft will only show its version number at start up HIGHLITE V1 0 Ordercode 30743 LED Par 64 Aircraft Main Menu Options ColProgr Progr 1 Built in Program ColSpeed Saeed ait Program Speed ColSet R WW 0 Dimmer Warm White aba Display Backlight aa Delay Mode DMX 1CH DMX 4 DMX 1 Channel Mode DMX 2CH DMX 1 DMX 2 Channel Mode DMX 3CH DMX 4 DMX 3 Channel Mode The LED Par 64 Aircraft will automatically detect the presence of a DMX signal In order to receive a DMX signal the controller must be attached to a DMX controller by a 3 5 pin DMX cable and the DMX controller must be turned on The LED Par 64 Aircraft system can operate as a 1 2 or 3 channel DMX fixture 1 Built in Programs With this menu you can set your desired built in program mode ColProgr 01 Press the MODE button on the device until the display shows O2 Press the Up Down buttons to choose 4 different programs 2 Program Spee
20. tput IP Rating IP 20 Housing Metal Connections Neutrik Powercon Powercon IN OUT XLR Data in out XLR 3 pin Cooling Convection Fuse F2 5A 250V Dimensions 403 x 269 x 269 LxWxH Weight 3 72 kg LED Par 64 Aircraft Overview Fig 01 Backside 01 LCD Display 02 Mode button O3 Up button 04 Down button 05 Neutrik Powercon OUT O6 Neutrik Powercon IN 07 Fuse F2 5A 250V 08 DMX signal connector OUT 3 pin 09 DMX signal connector IN 3 pin 10 Earth connection NOTE Knowledge of DMX is required to fully utilize this unit Ordercode 30743 8 shows a LED Par 64 Aircraft Installation Remove all packing materials from the LED Par 64 Aircraft Check that all foam and plastic padding is removed Connect all cables Do not supply power before the whole system is set up and connected properly Always disconnect from electric mains power supply before cleaning or servicing Damages caused by non observance are not subject to warranty Set Up and Operation Follow the directions below as they pertain fo your preferred operation mode Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa Control Modes There are 3 modes e Stand alone built in programs e Manual Dimmer Operation DMX512 1 2 or 3 Channels One Aircraft Built in Progr
21. ult in deterioration of the digital DMX signal Maximum recommended DMX data link distance 100 meters Maximum recommended number of Aircrafts on a DMX data link 30 fixtures Data Cabling To link fixtures together you must obtain data cables You can purchase DAP Audio certified DMX cables directly from a dealer distributor or construct your own cable If you choose to create your own cable please use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference DAP Audio Certified DMX Data Cables e DAP Audio coble for allround use bal XLR M 3 p XLR F 3 p Ordercode FLO1150 1 5m FLO13 3m FLO16 6m FLO110 10m FLO115 15m FLO120 20m e DAP Audio cable for the demanding user with exceptional audio qualities and connector made by Neutrik Ordercode FL71150 1 5m FL713 3m FL716 6m FL7110 10m The Aircraft can be operated with a controller in control mode or without the controller in stand alone mode Ordercode 30743 LED Par 64 Aircraft Control Panel A A LCD Display B Mode button C Up Button D Down Button Control board DMX 3CH DMX 1 EE B C D Fig 04 Control Mode The fixtures are individually addressed on a data link and connected to the controller The fixtures respond to the DMX signal from the controller When you select the DMX adaress and save it the controller will display the saved DMX address the next time
22. y transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only Ordercode 30743 2 Show 23 a LED Par 64 Aircraft IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any Unauthorized modification to the device Ordercode 30743 3 Show 23 a Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Never remove warning or informative labels from the unit Never use anything to cover the ground contact Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles Never place any material over the lens Never look directly into the light source Never leave any cables lying around Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Do not insert objects into air vents Do not connect this device to a dimmerpack Do not switch the device on and off in s
Download Pdf Manuals
Related Search
Related Contents
EUROLIVE F1220A 手すり『ハンドバー』 Bionaire BASF1016G fan GAGGIA Classic Coffee Cayenne S Hybrid 1 Moteur thermique Product Manual Fingerprint Access Control/ Attendance Time Clock User Manual Home Run 3.0 16 Port Nway Fast Ethernet Switch User's Manual Copyright © All rights reserved.
Failed to retrieve file