User Manual - Transmitter Solutions
Contents
1. L ae q KEYPADLIGHT GO NOGO 1 SOUND 2 LED 3 LIGHTS 4 Notused 5 Notused 6 WIRELESS MODE a Switching this dip switch to off will enable the toggle gate feature and switching to the on position will disable the toggle gate feature Disabling this feature can potentially save battery power in the case that the toggle gate feature has been accidentally activated Refer to the programming chart for more details with the toggle gate feature 7 Notused 8 Not used OPTION 2 Installing a 433MHz Module STEP1 STEP2 Prepare the Remove cut the 433 MHz module battery connector Antenna Activation Wires Common amp Normally Open STEP 3 Install the 433 MHz Module to the keypad board ADAPT ANS SS lt K oe u gt e cy 4 ee pa J y g Uc ZLTA fi DES we 2 T YOy 9 Ew jase y t e VDC BATTERY IMPORTANT Be sure to connect the power source to the correct terminals The battery terminals and the AC DC terminals are different 7 i GO NOGO KEYPADLIGHT lt Any channel can be assigned for devices that connect to normally open normally closed 3 Programming Guide NOTE Default Master Code 11 2 3 4 o Add Access Codes Channel 112113114 L JL IL IL New Access Code Example STEP 1 Press 12 3 4 STEP2 Press 1 STEP 3 Enter access code 22. 2 STEP 4 Press 1 multiple beeps confirm STEP 5 Press STEP 6 Test new access code _ light will flash 6 times confirming that the new access code has been accepted STEP 7 Install the module STEP 8 Proceed to program the keypad to the receiver Use Channel 1 if unsure The different channels are dependent on the RF terminal used Any channel can be assigned for devices that connect to normally open normally closed e Remove Access Codes Helsi ei LIL IL TE Access Code to Delete Set Relay Output Time 1111211314 Seconds 0 60 Change Master Code 1 2 3 41 OOL New Master Code Clear All Codes 1 2 3 4 NOTE This will clear all data except the Master Code kd Advanced Features Add Guest Code Channel 1111211314 OUL Access Code The Guest Code is a one time use access code Once used the number will be cleared from memory Add Access Toggle Code Channel Helia A OLL Toggle Code NOTE TOGGLE MODE ONLY FOR USE WHEN KEYPAD IS HARD WIRED Entering Access Toggle Code will toggle the keypad to continuously activate Entering the code again will toggle the keypad off Dip switch 6 on the circuit board needs to be in the off position in order for this mode to work Resetting the Keypad and Master Code Locate the red Master Reset Button on the circuit board 1 Remove the battery or eliminate the power source to the keypad Wait 30 seconds for the keypa
3. DOL1000 MF Keypad 233 EE 4515 Terminal Guide Module Installation Programming Guide Dolphin Advanced Features ystems Tete 916 RESET BUTTON OITO Wr Bg FR o 1 A M NN AJ 7 P4 a gt ul x 9 Jil sto T These terminals will supply power to the transmitter Channel 1 terminal Normally open Use N O for equipment that requires a temporary surge of electricity to activate Example Electric door locks automated gates push plates etc cow Common ground e NC Normally closed Use N C for equipment that requires a constant flow of electricity to function properly Example Magnetic locks receivers etc BATTERY 6VDC If deciding to power the DOL1000 MF with a battery then connect the battery to these terminals 6 24VAC DC If deciding to hardwire the DOL1000 MF directly to a power source use these terminals Master Reset Button Holding this button down for 5 seconds reconnecting to its power source will make the keypad beep 3 times This will indicate that the Master Code has been reset to 1234 Installing a Dip Switch Module Be sure to connect the power source to the correct terminals The battery terminals and the AC DC terminals are different 0 or N 14771 40 1 HALIMS did af
4. EM AS IS WHERE IS TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND WHETHER DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING INJURIES TO PERSONS OR PROPERTY TO BUYER ITS EMPLOYEES OR AGENTS AS A RESULT OF THE SALE BUYER ALSO AGREES TO HOLD TRANSMITTER SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER OR ANY THIRD PARTY MAY HAVE AS A RESULT OF BUYER S USE OR DISPOSAL OF THE GOODS BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS TransmitterC SOLUTION S 3788 West 2270 South Suite E Salt Lake City UT 84120 866 975 0101 866 975 0404 fax www transmittersolutions com
5. d to completely power off 2 Press and hold the Master Reset Button 3 While holding the Button reconnect the battery or power source to the keypad 4 Continue to hold to Button until the keypad beeps 3 times This indicates that the Master Code has been reset to 1234 Specifications IP Rating IP64 Temperature Rating 40C to 70C 40F to 158F Size 7 1 2in x 7 3 4in x 3 5 8in Weight 1 34 Ibs Housing ABS Face Plate Material ABS Operating Voltage 6 24 AC DC Output relays 1A TRANSMITTER SOLUTIONS WARRANTY The warranty period of Transmitter Solutions keypad is twenty four 24 months This warranty shall begin on the date the keypad is manufac tured During the warranty period the product will be repaired or replaced at the sole discretion of Transmitter Solutions if the product does not operate correctly due to a defective component This warranty does not extend to a the keypad case which can be damaged by conditions outside the control of Transmitter Solutions or b battery life of the keypad This warranty is further limited by the following disclaimer of warranty and liability EXCEPT AS SET FORTH ABOVE TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE GOODS EXPRESS OR IMPLIED INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICU LAR PURPOSE BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER SOLUTIONS EXPRESS OR IMPLIED WITH REGARD TO THE GOODS AND ACCEPTS TH
Download Pdf Manuals
Related Search