User`s manual
Contents
1. or lt The current underline frame setting appears in the display Press lt 7 and gt until the desired underline frame setting is displayed Press or to apply the selected underline frame setting to the text MIRROR PRINTING This function prints your label so that the text can be read from the adhesive side of the tape If mirror printed labels are attached to glass or some other transparent material they can be read correctly from the opposite side Note e With this function the text must be printed on transparent tape e To quit the following procedure at any time without making any changes press GN Press Ceca Press amp 7 and gt until MIRROR is displayed and then press or lt The current mirror printing setting appears in the display Press amp 7 and gt until the desired mirror printing setting is displayed Press or lt to apply the selected mirror printing setting to the text TAPE MARGIN This function can be used to leave equal margins of 1 6 4 mm 4 1 2 12 mm or 1 24 mm on both sides of the text Using the tape margin setting multiple formats can be printed with margin 8 mm one after the other without feeding the tape onto a single label Note To quit the following procedure at any time without making any changes press lo Press S Press 7 and gt until MARGIN is displayed and then press or lt The current tape margin set2. 9 corresponding to the file number of the text that you want to recall Press or lt to clear the display and recall the selected text DELETING A TEXT FILE Note To quit the following procedure at any time without making any changes press CoN Press ao Press amp 7 and gt until MEMORY is displayed and then press or lt Press lt 7 and gt until DELETE is displayed and then press or lt The message 1 9 appears in the display Press lt 7 and gt until the text file that you want to delete is displayed OR Press the key 1 9 corresponding to the file number of the text that you want to delete Press or lt to delete the selected text file ERROR MESSAGE LIST ERROR An error has occured such as the tape is incorrectly loaded or the font selected is to large for the tape etc BATTERY The batteries are weak The maximum number of characters 55 characters including spaces FULL have already been entered or the memory is full TROUBLESHOOTING 1 The display stays blank after you have e Check that the batteries are correctly turned on the machine inserted e Ifthe batteries are weak replace them 2 The machine does not print or the e Check that the tape cassette has been printed characters are blurred inserted correctly e Verify that the tape cassette is not empty and if so replace the tape cassette e Check that the character size is appropriate for
3. q sey yu wdinb siy L JOILON 994 99U9194 1 1N N JO BOe d Apuey e ul JenuewW y d y pue uies aojegq Ajjnjaseo penuew siy pea noA yeu seHHns m asn o se si uiyoew siy yBnouly ulyoLew yeonoeid jewax ue y SOMCW 064 L Ld 24 Jo eOUeWOJJEd pue Aypenb y woy y JO qel y A1098 y BdIJJO y UJ Bunuud jeuoiss zord nb yey syse JUeHIN Inoge Aom o BAeY JBHUC OU NA S10 09 Buljloxe pue SUIPIM uaap YUM sj qel uid 0 NOA smojje jqeere s puyeo ede jo enea y uoppe ul sjaqej wosno nyyneaq Ubisep oO s j s pue s z s J9 0e1eYO somes Auew y woy 20199 UOIedI dde Aue 10 sjaqej 242919 UD NOA 064 L Ld MOU 1NA YIM NOILONGOY ZLNI Backspace key GENERAL PRECAUTIONS e To avoid injuries do not touch the cutters edge e Use only Brother TZe tapes with this machine to avoid damage Do not use tapes that do not have the mark e Tapes are available in three different widths 0 23 6 mm 0 35 9 mm and 0 47 12 mm e Do not pull the tape since this may damage the tape cassette e Do not attempt to cut the tape while printing or feeding since this will damage the tape e Do not clean the machine with alcohol or other organic solvents Use only a soft dry cloth e Remove the batteries if you do not intend to use the machine for an extended period of time Note If power is disconnected for more than three minutes all text shown in the display and any text f
4. to cut off the label and then use scissors to cut along the printed dots and center the text within the label REPEAT PRINTING This function allows you to print up to nine copies of the same label Note To quit the following procedure at any time without making any changes press lo Press ce Press 7 and gt until REPEAT is displayed and then press or lt The message 1 9 appears in the display Press 7 and gt until the number of labels that you want to print appears on the right side of the display OR Press the key 1 9 corresponding to the number of labels that you want to print Press or SS or to print the labels Note e After printing with the tape margin setting hold down and press Gn once to feed the tape before pushing in the tape cutter lever to cut it e After printing with the or tape margin setting push in the tape cutter lever to cut off the tape and then use scissors to cut along the printed dots and separate the labels This function can be used to print many copies of the same text while increasing a selected number by 1 after each label is printed for example when printing labels containing a serial number for example 0123 0124 and 0125 Note To quit the following procedure at any time without making any changes press CO Position the cursor below the number that you wish to increase Press ao Press lt 7 and gt until NUMBER
5. 54 mm W x 5 5 64 129 mm D x 2 1 2 64 mm H Weight 0 9 lbs 400 g without batteries and tape cassette Buffer size 55 characters including spaces Memory size 300 characters including spaces maximum 9 text files Warranty For USA Only 90 Days One Year Limited Warranty and Replacement Service For further details regarding the warranty please refer to the warranty card that is included with this product Thank you for purchasing this Container Store Product We hope that you will enjoy using it We suggest that you keep all packing and other materials After referring to the instruction manual if you still need assistance call Brother Customer Service at Voice 1 877 BROTHER 1 877 276 8437 Web www brother com Fax 1 901 379 1210 If you need to locate a service center please call 1 877 BROTHER 1 877 276 8437 or visit us at www brother com
6. ER layer e Insert ends before ends Sanne a e Remove ends before ends i ri e Replace all 6 batteries at the same time with new ones il TT Insert tape cassette 7 Insert two hooks on bottom end of back cover into slots on bottom of machine Push down firmly on cover until it snaps into place Turn machine on If no power immediately remove batteries and call Brother Customer Service at 1 877 BROTHER 1 877 276 8437 OVERVIEW Tape cutter lever Display Function key Return key Back cover Caps key On Off key Num key Print head Batteries Tape cassette TAPE CASSETTES This machine uses the Brother TZe tape which is available in a variety of colors and three widths 0 23 6 mm 0 35 9 mm and 0 47 12 mm Two TZe tapes are supplied with this machine Press in on the rough area at the top end of the machine and fold open the back cover Should be the exact process as loading batteries If a tape cassette is already installed remove it by pulling it straight up If the ink ribbon in the other tape cassette is loose use your finger to wind the toothed wheel in the direction of the arrow on the cassette until there is no slack in the ribbon Also make sure that the end of the tape feeds under the tape guides Note If you are using a new tape cassette provided with a stopper be sure to remove the stopper Insert the tape casset
7. The Container Store MODEL PT 1190 USER S GUIDE TZO TAPE Printed in China LAD987001 oy souisnpu seyjoig Aq poumo ae UOIUM Souweu 1onpoid pue syewepe sjenoyew PS1UHUAdOD surezuoo JUBLWUINDOP SIU JUsWUdINbe y eyesedo 0 AjOUINe sasn y PIOA PjNOO pr seuisnpuy Jeulojg Ag peroudde Ajsseidx9 10U SUOITeOIII OOW 10 seBueYyD diay 10 UBIDIUYOS A Olpes paouanedx Ue JO Ijeap y yNSUOD P9 OD9UUOD SI JADI y YOIUM O Jey WOI JUSIAYIO PNOO e UO Jeno Ue o JUBLUCINbS y JO9UUOD J Al3091 pue JUSLUCINDS y ussmeq uoeed s y sSe u euugzue Hula BU 9720091 JO JU HOSY Seinseaw HulMmo o y JO BOW JO BuO Aq 9U31 9 U y 1081109 0 AJ 0 pebeinoous s 1 sn y UO pue yo pu wdinb y Buluin Aq p uiw p aq UBD YOIYM uodas UOISIAS 9 JO Opel 0 DOUSJOPSJUI Nzuey asneo s op yu wd nb s y J UOe e SU We NOed e ul 1NDDO 10U JIM BOUBJOLSIU yeu dejUeJeNH OU SI 819 AABMOH SUOIJEOIUNWLWOD OIPes 0 BOUdIO9 UI Injwuey sneo Aew SUOIJONIJSUI 3y UUM BOUePJODOe UI p sn pue p jezsul 10U JI pue A6saue Aou nb oipe ayeipes ued pue sasn sa esoueb zuowdinbe siy L UONEI E SUI jeuapisa e ul BOUSJOLEJU NJUWeY suree UO ND9 01d jqeuosea piaod o p uf s p ae syw s y L s Nny OD ey Jo GL Hed 0 uensund adIAep jepp g Ssg e JO spw y YUM Ajdwo 0 punoy pue pasa u
8. e the corresponding function or add the corresponding character to your text CAPS KEY By pressing to enter Caps mode you can add upper case letters to your text by simply pressing the character keys When this mode is on the Caps indicator in the top left corner of the display comes on To exit Caps mode press until the Caps indicator goes off NUM KEY By pressing um to enter Num mode you can add numbers to your text by simply pressing the corresponding keys When this mode is on the Num indicator in the bottom left corner of the display comes on To exit Num mode press Aum until the Num indicator goes off DISPLAY This machine s LCD shows one row of 8 characters however the text that you enter can be up to 55 characters including spaces The 8 character display is like a window which moves across the text lt p gt 1234567890123456789012345678901234567890123456789012345 Es CURSOR MOVEMENT You can view and edit different parts of the text by moving the cursor backward and forward To move the cursor one character at a time press amp 7 or gt To move the cursor to the beginning of the text hold down and press 7 To move the cursor to the end of the text hold down and press O BACKSPACE KEY This key can be used to remove characters from your text clear all of the text or cancel the current function and return to the text input mode To delete the character to the left o
9. f the cursor or to cancel a function press GN To clear all of the text that is currently entered hold down and press lo SPACE KEY As on a word processor press to add a blank space to your text RETURN KEY Press when you wish to accept or confirm a setting or end the first line of text and start the second To adda second line press amp once The return mark J appears in the text to indicate the end of the first line and the beginning of the second Note Two lines of text can only be entered if 0 35 9 mm or 0 47 12 mm wide tape is installed To accept or confirm a setting from a list press amp once ACCENTED CHARACTERS You can also choose from a list of other accented characters that can be added to your text Accented character Accented character Press if you want the accented character to be an upper case letter Note To quit the following procedure at any time without making any changes press GN Hold down and press TD The message A U appears in the display Press the key for the letter in the accented character that you wish to add and then press lt 7 and gt until the cursor is positioned under the desired accented character Press lt to add the selected character to your text SYMBOLS In addition to the letters symbols and numerals on and above the keys there are 72 symbols available with the Symbol function These symbols are divided into 9 groups co
10. iles stored in the memory will be lost e Do not put any foreign objects into the machine e Do not put anything on top of the machine e Do not expose the machine to high temperatures or high humidity Never leave it on the dashboard or in the back of your car e Do not use the machine in dusty places and keep it out of both direct sunlight and rain e Do not leave any rubber or vinyl on the machine for an extended period of time which may cause staining of the machine e After inserting a new tape cassette advance the tape by holding down and pressing once e Donot touch the print head mechanism If the head is touched clean it immediately with a soft wipe e g a cotton swab to avoid permanent damage e To prevent damage during shipment a clear protective sheet is placed over the LCD panel Remove this clear protective sheet before beginning use POWER SUPPLY Changing the batteries CAUTION Batteries installed incorrectly can overheat and leak This can result in chemical burns and machine overheating and damage Your machine requires 6 alkaline AAA batteries Carefully follow these instructions Press bumps on top of back cover and open Pull out tape cassette if one was installed Remove batteries if they were already installed Hold machine as pictured Inser six new batteries as follows FIRST in SECOND in Always LOWER layer UPP
11. in your label If a setting other than NORMAL is selected the Style indicator at the bottom of the display lights up NORMAL J SMITH SHADOW J SMITH I1 BOLD italic bold J SMITH Note e If there are two lines of text they are printed in the NORMAL style regardless of the selected style setting e To quit the following procedure at any time without making any changes press CoN Press Press amp 7 and gt until STYLE is displayed and then press or lt The current style setting appears in the display Press amp 7 and gt until the desired style setting is displayed Press or lt to apply the selected style setting to the text OUTLINE J SMITH BOLD J SMITH ITALIC I OUTL italic outline J SMITH J SMITH I SHADOW italic shadow VERTICAL JLS MITH i f i f i gt D MS FL i UNDERLINE FRAME This option allows you to emphasize or decorate your entire text by framing or underlining it If any setting other than OFF is selected the Undl Frm indicator at the bottom of the display lights up OFF no underline or frame ROUND WOODEN ABC POINTING CANDY UNDL underline ABC X ABC X ABC Note e The underline or frame is not printed if the VERTICAL style setting is used e To quit the following procedure at any time without making any changes press 6N Press Press 7 and gt until UNDL FRM is displayed and then press
12. is displayed and then press or lt 4 The message 1 9 appears in the display Press 7 and gt until the last number that you want to print appears on the right side of the display OR Press the key 1 9 corresponding to the last number that you want to print Note The last number that will be printed must be larger than the number selected in the text otherwise the message ERROR will appear when you try to print Press or lt 7 or to print the labels Note e After printing with the tape margin setting hold down and press once to feed the tape before pushing in the tape cutter lever to cut it k e After printing with the or tape margin setting push in the tape cutter lever to cut off the tape and then use scissors to cut along the printed dots and separate the labels MEMORY You can use the memory to store your most frequently used text The text file remains in the memory even after all characters are removed from the display by holding down and pressing C Later the text can easily be reused by recalling it from the memory The machine s memory can store up to 300 characters including spaces which can be divided into as many as nine text files The maximum capacity for a single text file is 55 characters including spaces STORING TEXT lear Note To quit the following procedure at any time without making any changes press Press Qoca Press lt 7 and gt u
13. ntil MEMORY is displayed and then press or lt Press amp 7 and gt until STORE is displayed and then press or lt The message 1 9 appears in the display Press amp 7 and gt until the file number where you want to store the text is displayed OR Press the key 1 9 corresponding to the file number where you want to store the text Press or lt to store the text The text previously shown in the display reappears Note e To avoid injuries do not touch the cutter s edge e If the file number you selected already contains text the message ERROR appears Press or lt and then select a different file number e f nine text files are already stored the message ERROR appears Press or lt and then delete one of the stored text files before trying to store the current text e If 300 characters are already stored the message FULL appears Press or lt and then delete one of the stored text files before trying to store the current text RECALLING TEXT lear Note To quit the following procedure at any time without making any changes press Press Ceco Press 7 and gt until MEMORY is displayed and then press or lt Press amp 7 and gt until RECALL is displayed and then press or lt The message 1 9 appears in the display Press lt 7 and gt until the text file that you want to recall is displayed OR Press the key 1
14. rresponding to the letters A through I Press aD The message A I appears in the display Press the key for the letter of the group containing the symbol that you wish to add and then press say and gt until the cursor is positioned under the desired symbol Press lt to add the symbol to the text The characters in the text can be set to one of five different sizes in addition to AUTO which automatically adjusts the characters to the largest possible size according to the width of the installed tape The currently selected size setting is shown by the indicators at the top of the display All of the size indicators light up when the AUTO setting is selected SIZE 1 A standard size SIZE 2 A double width SIZE 3 A double height JSMITH SIZE 4 double width amp double height SIZE 5 4x width amp double height J SMITH J SMITH Note e If there are two lines of text they are printed with the SIZE 1 setting applied regardless of the selected size setting e To quit the following procedure at any time without making any changes press GN Press Qao Press lt 7 and gt until SIZE is displayed and then press or lt The current size setting appears in the display Press amp 7 and gt until the desired size setting is displayed Press or lt to apply the selected size setting to the text STYLE You can also use one of nine different print styles for the characters
15. te firmly into the compartment making sure that the entire back of the cassette contacts the bottom of the compartment Note When inserting a tape cassette make sure that the inner ribbon does not catch on the corner of the metal guide Securely close the back cover making sure that it snaps into place Feed the tape by holding down and pressing once and then push in the tape cutter lever to cut the tape LETTERING STICK The enclosed lettering stick enables you to easily remove the backing from laminated tapes Hold the tape in your left hand with the printed surface facing up and hold the stick in your right hand Pass the tape halfway through the long narrow hole in the stick 22 Turn the stick three quarters of a turn towards you and pull the stick away from you as shown below 4 Peel off the label backing STARTING Press o If batteries have been installed the previous session s information is displayed when the machine is turned on This feature allows you to stop working on a label and turn off the machine then return to it later without having to re enter the text The machine automatically turns off if no key is pressed within five minutes The current session s information is stored in the machine s internal memory and displayed when the machine is later turned on again CODE KEY By holding down and pressing a key with a function character or accent written above it you can us
16. the width of the tape that is used 3 The printed characters are not formed e Ifthe batteries are weak replace them properly 4 Striped tape appears e The tape cassette is empty Replace it 5 The memory has cleared on its own e The batteries may be weak Replace them 6 A blank horizontal line appears through e There may be some dust on the print the printed label head Remove the tape cassette and use a dry cotton swab to gently wipe the print head with an up and down motion Try printing again and if the dust still remains dip a cotton swab in isopropyl rubbing alcohol and gently wipe the print head again e Turn off the machine and then while holding down and 6N press to turn the machine back on Finally release and lo Note The text and formats in the display and all text files stored in the memory are erased 7 The machine has locked up i e nothing happens when a key is pressed even though the machine is on SPECIFICATIONS Keyboard 42 keys Print speed 10 mm sec Standard size Double width Double height Double width amp double height 4 0 width amp double height Character size Character font HELSINKI Print tape Pressure sensitive adhesive based TZe tape only Three widths available 0 47 12 mm 0 35 9 mm 0 23 6 mm LCD 7 x 5 dots 1 line x 8 characters Power supply Six AAA size alkaline batteries LRO3 Auto power off Dimensions 6 1 16 1
17. ting appears in the display Press K7 and gt until the desired tape margin setting is displayed 4 Press or lt to apply the selected tape margin setting to the text Note e After printing with the tape margin setting hold down and press once to feed the tape before pushing in the tape cutter lever to cut it otherwise some of the printed characters may be cut off e After printing with the or tape margin setting push in the tape cutter lever to cut off the label and then use scissors to cut along the printed dots and center the text within the label PRINTING amp CUTTING After you have entered the text and chosen the desired format settings you are ready to print the label To print the label press oF The message PRINT is displayed while the label is being printed and the label comes out of the tape exit slot at the top end of the machine To feed out 1 1 24 25 mm of tape for example after printing using the tape margin setting hold down and press once The message FEED is displayed while the tape is fed out hi To cut off the label push in the tape cutter lever in the top right corner of the machine Note e To avoid injuries do not touch the cutters edge e In order to prevent damage to the tape do not try to cut it while the messages PRINT or FEED are displayed e After printing with the or tape margin setting push in the tape cutter lever
Download Pdf Manuals
Related Search