Liberty 1T36 Battery Uplighter
Contents
1. button to confirm the setting The unit will now run in sequence with the master unit To exit out of any of the above options press the MODE button Please ensure that all slave units are set to the same DMX channel mode as the master unit Sound active mode To access the sound active mode press the MODE button on the rear of the unit to show SOUND SENS on the LCD display Now press the ENTER button and use the UP and DOWN buttons to set the sound sensitivity level from OO 31 Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button Dimmer response To access dimmer response press the MODE button on the rear of the unit to show DIMMER RESPON on the LCD display Now press the ENTER button and use the UP and DOWN buttons to select between DIMMER RESPONO1 LED dimming or DIMMER RESPONO2 halogen dimming Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button Power mode this gives you the option to have the unit illuminated or off whilst charging To access the power mode press the MODE button on the rear of the unit to show POWER on the LCD display Now press the ENTER button and use the UP and DOWN buttons set to ON or OFF ON the unit will be illuminated whilst charging OFF the u2. lumen8s amp Liberty 1T36 Battery Uplighter 1 x 36W COB tri colour LED RGB User Manual Order ref LEDJ9O0B Order codes ELUM117 Black housing ELUM117A White housing Lumen8 Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCKH IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or info
3. 255 Master dimmer 0 100 DMX address examples To set the DMX address press the MENU button on the rear of the unit to show DMX MODE on the LCD display Now press the ENTER button and use the UP and DOWN buttons to choose between the adresses 000 512 Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button Colour mode To access the static colour mode press the MODE button on the rear of the unit to show 1 STATIC on the LCD display Then press the ENTER button and use the UP and DOWN buttons to change between static colour colour change 7 colour colour change 3 colour and colour fade modes Press the ENTER button to confirm the setting Now use the UP and DOWN buttons to select the RGB brightness and F flash speed Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button www elumensg co uk Liberty 1T36 Battery Uplighter User Manual 5 lumen8 Master slave mode To set the master unit press the MODE button on the rear of the master unit then select your desired program sound active auto static colour colour fade or one of the built in programs To set the other units in slave mode press the MODE button on the rear of the unit to show SLAVE MODE on the LED display and press the ENTER
4. Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CE ie www elumen 8s co uk Liberty 1T36 Battery Uplighter User Manual 12
5. LR socket Pin 2 Signal COT Pin t GND screen Pin 3 Signal Pin 2 Signal Pin 4 N C Pin 3 Signal Pin 5 N C 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal F B A 2 www elumen8 co uk Liberty 1T36 Battery Uplighter User Manual 10 lumen8 Please contact your local retailer to purchase these accessories BLACKOUT DIMMING R O G AUTORUN SELECT PROG FLASH SPEED DMXMODE SOUND ACTIVE SLAVE SET ADDR OHO 0000 0000 0000 Optional IR remote Order code LEDJ90B To keep up to date on the latest accessories and product range additions please visit www prolight co uk www elumens co uk Liberty 1T36 Battery Uplighter User Manual Optional accessories 11 lLumen8 WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries SS with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources
6. ble battery for wireless applications e IEC power input output e 3 Pin XLR in out sockets e Convection cooled e Optional IR remote LEDJ9OB 20 Lux 4500 1688 686 397 264 110 Lux 500 130 60 36 24 i _ l a SS Om im 2m 3m 4m 5m 220mm 265mm a www elumen8 co uk B LIBERTY M i d UPLIGHTER W a oga CE owen our fe 00 3000 on d MAN turou Specifications Liberty 1T36 battery uplighter Power consumption 120W when charging Battery life 6 8 hours full on 11 13 hours colour fade Battery recharge time 5 hours Power supply 100 240V 50 60Hz Dimensions 265 x 220 x 190mm Weight 5 8kg Order code ELUM117 Black housing Order code ELUM117A White housing battery life subject to usage and the environment where the fixture is situated 190mm Liberty 1T36 Battery Uplighter User Manual 3 Lumens Technical specifications Ol fall aa j I 1e ooooo0oo0000000 O000000000 O00000000000 O000000Q9 cil on ox Llumen8 BERTY 1136 AENEAS SAIK UPLIGHTER B 09 MODE ENTER uP DOWN X Be e a Gai Pot UT ne 01 Microphone O7 IEC power out socket 12 Tightening knobs for angle 02 Earth point 08 Function buttons adjustmen
7. e fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Note DMX cable must be daisy chained and cannot be split www elu
8. indicator LED is green on and red flashing it means the connection is good but the fixture is not receiving the DMX signal from the transmitter www elumensg co uk Liberty 1T36 Battery Uplighter User Manual 7 lumen8 Optional IR remote functions Button functions 01 Blackout 02 Set the LEDs colour then use the and buttons to change the brightness 03 Set in auto run 04 Run the built in programs then use the and buttons to go through the programs 05 Set the LEDs to flash on and off then use the and buttons to change the flash frequency O6 Set the run speed then use the and buttons to change the desired speed note only available in the colour change or colour fade modes 07 Set the LEDs into DMX mode 08 Set the LED into sound active mode 09 Set the LEDs into slave mode 10 Set the DMX address for the LEDs Optional IR remote Order code LEDJ90B DMX address examples To set the DMX address 245 e Now press the 5 button and all of the e Press the S button the red LEDs will come on R G B LEDs will come on the third digit 5 you can now start to set the DMX address has been set The full DMX address setting e Now press the 2 button the green LEDs will has been changed come on this means the first digit has been e Now press the DMX MODE button to save set at 2 the new address into the mem
9. mensg co uk Liberty 1T36 Battery Uplighter User Manual 9 lumen8 DMX setup Notice Be sure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out 3 pin XLR DMX 512 in 3 pin XLR a a ee XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3 Hot 3 Hot Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interference It is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order code CABL9O 5 pin Order code CABL89 5 pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion 5 pin XLR socket Pin 1 GND screen 3 pin X
10. nit will be off whilst charging Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button www elumensg co uk Liberty 1T36 Battery Uplighter User Manual 6 lumen8 Battery reference information When the battery charge indicator LED is illuminated red the fixture is recharging When the battery charge indicator LED is illuminated green the fixture is charged When the battery life indicator LED s are illuminated green the following rules apply 4 indicators 100 charged 3 indicators 75 charged 2 indicators 50 charged 1 indicator 25 charged The recharging time for the battery is 5 hours The battery usage time from fully charged is dependant on the mode and brightness of the fixture For more information please see the specifications table on page 3 Wireless DMX To activate the wireless DMX receiver press the mode button until the display shows Wireless Off press ENTER to access the menu and then UP DOWN to select Wireless On When the wireless DMX signal indicator LED is illuminated red the wireless receiver is not active When the wireless DMX signal indicator LED is flashing red and green the wireless DMX receiver is on and is trying to connect to the wireless DMX transmitter When the wireless DMX signal indicator LED is green the connection to the wireless DMX transmitter is good When the wireless DMX signal
11. ory e Now press the 4 button the blue LEDs will come on this means the second digit has been set at 4 Important notes e Set the DMX address on each fixture before plugging into the DMX controller e The IR remote is cannot be used when the fixture s are being controlled by a DMX controller e The maximum transmitter distance is 10m Please make sure that you have the IR remote aimed directly at the front panel of each fixture to be programmed e If you do not press the DMX MODE button after you have changed the DMX address when you power down the fixture it will lose the address you have set www elumensg co uk Liberty 1T36 Battery Uplighter User Manual s8 lLumen8 DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to th
12. r 90 days from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www elumensg co uk Liberty 1T36 Battery Uplighter User Manual 2 lumen8 Liberty 1T36 battery uplighter Product overview amp technical specifications Housing a 1 x 36W tri colour LED the Liberty 1T36 battery uplighter gives smooth colour mixing from rich saturated hues to subtle pastel shades These units have a rugged housing and feature a 4 push button LED menu which allows for easy access to the functions including DMX master slave sound active and stand alone An optional 20 lens is included to further increase the fixtures applications e 2 year warranty e 1x 36W tri colour LED RGB e Beam angle 110 e Beam angle with lens 20 field angle 28 e Refresh rate 3 6kHz e DMX channels 3 or 5 selectable e Wireless DMX control from W DMX e Static colour colour change colour fade auto sound active and master slave modes e 0 100 dimming and variable strobe e Adjustable angle e Carry handle e Safety bond security chain point e 4 push button menu with LCD display e Rechargea
13. rmative labels from the unit If the equipment has been exposed to drastic Do not open the equipment and do not modify the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use e Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable Only use fuses of same type and rating WARRANTY Two years from date of purchase ae NOTE Batteries are classed as consumable items which periodically are covered fo
14. t 03 IEC power in socket 09 On off buttons 13 Battery indicator 04 Fuse F2A 250V 10 LCD display 14 Charge Indicator 05 DMX in socket 11 Wireless DMX 15 Wireless DMX signal indicator 06 DMX out socket antenna In the box 1 x fixture 1 x IEC mains cable amp 1 x user manual Operating instructions Please note This fixture is not supplied in a fully charged state and must be charged for up to 24 hours before operation Angle adjustment Use the tightening knobs on either side of the fixture to adjust the angle from O 90 www elumen8 co uk Liberty 1T36 Battery Uplighter User Manual 4 lumen8 DMX channel mode Operating in DMX control mode gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX channel mode press the MENU button on the rear of the unit to show CHANNEL on the LCD display Now press the ENTER button and use the UP and DOWN buttons to choose one of the 3 or 5 DMX channel modes Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button 3 channel mode 000 255 Red 5 channel mode Channel Value Function 000 255 Red 0 100 2 000 255 Green 0 100 000 255 000 255 3 000 255 Blue 0 100 000
Download Pdf Manuals
Related Search