Sweeper Beam LED User Manual
Contents
1. Reset ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 9 Sweeper Beam LED System Menu System Menu When making adjustments press ENTER to confirm your setup and then press and hold the MENU button for at least 3 seconds To exit without making any adjustments press the MENU button ADDR DMX Address Setting 1 Press the either the MENU UP or DOWN buttons until ADDR is displayed press ENTER 2 The current address will now be displayed and flashing Press the UP or DOWN buttons to find your desired address Press ENTER and then press and hold the MENU button to set your desired DMX address SLND This will let you set unit as a master or slave in a master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either MAST SL 1 or SL 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is displayed press ENTER and then press and hold the MENU button to confim NOTE In a Master Slave configuration you can set one fixture to Master and then set the next fixture to SL 2 the fixtures will now have contrast movement to each other CHND This will let select your desired DMX channel mode 1 Press the either the MENU button until CHND is displayed press ENTER Either 1CH 6CH 11CH or 15CH will be displayed 2 Press the UP or DOWN buttons to choose your desired DMX2. 3 13 r SWEEPER AD BEAM LED User Instructions Sweeper Beam LED General Information Unpacking Thank you for purchasing the Sweeper Beam LED by ADJ Products LLC Every Sweeper Beam LED has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to oper ate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Sweeper Beam LED is an intelligent 8 zone LED beam effect The Sweeper Beam LED can operate as a stand alone fixture or in a Master Slave configuration The Sweeper Beam LED has three operating modes sound active mode show mode and DMX control This fixture is suitable for theaters studios retail stores and other similar locations This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initi
3. Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse Sweeper Beam LED Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Sweeper Beam LED P Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the rear pan
4. Sweeper Beam LED Hanging Precautions Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Regardless of the rigging option you choose for your Sweeper Beam LED always be sure to secure your fixture with a safety cable not included Caution For added protection mount the fixtures in areas out side of walking paths seating areas or areas were the fixture might be reached by unauthorized personal Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight To avoid injury never stand directly below the device when mounting removing or servicing the fixture Always use and install a safety cable not included as a safety measure to prevent accidental damage and or injury in the event the clamp fails Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 5 Sweeper Beam LED Set Up Power Supply The ADJ Sweeper Beam LED contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lig
5. L E D Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 23 Sweeper Beam LED Specifications Model Voltage LEDs Power Consumption Beam Angle Dimensions Colors Weight Fuse Duty Cycle DMX Sound Active Working Position Warranty Power Cord Daisy Chain Sweeper Beam LED 100V 240V 50 60Hz 8 x 3W White Cree LEDs 47W 3 5 Degrees 9 Fixtures Max 38 5 L x 3 W x 5 25 H 973mm x 73mm x 132mm White 13 Lbs 6 3 kgs 7A None 1 6 11 amp 15 DMX Channel Modes Yes Any Safe Secure Position 3 Year 1095 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info adj com A D J Supply Europe B V Junostraat 2 E 6468 EW Kerkrade Netherlands serviceQadj eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow U
6. TILT is displayed press ENTER 2 The display will show either YES or NO Press the UP or DOWN buttons to select YES to activate tilt inversion or ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 13 Sweeper Beam LED System Menu NO to deactivate tilt inversion 3 Press ENTER and then press and hold the MENU button for at least 3 seconds to activate DISP This will flip the LED display 180 1 Press the MENU button until DISP is displayed press ENTER 2 Either DISP or DSIP will now be displayed Press the ENTER button to flip the display TEST This function will run a self test program 1 Press the MENU button until TEST is displayed press ENTER 2 The fixture will now run a self test FHRS with this function you can display the running time of the fixture 1 Press the MENU button until FHRS is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit VER with this function you can display the version soft ware of the fixture 1 Tap the MENU button until VER is displayed press ENTER 2 The software version will now be displayed Press MENU to exit ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 14 Sweeper Beam LED Operation Operating Modes The Sweeper Beam LED can operate in three different modes In each mode you can run the fix
7. mode and press ENTER to confim and exit ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 10 Sweeper Beam LED System Menu SET This will set the Sweeper to a preset angle 1 Press the either the MENU button until SET is displayed press ENTER Either 150 120 or 90 will be displayed these are the preset angles 2 Press the UP or DOWN buttons to choose your desired angle and press ENTER to confim and exit SHND SH 0 SH16 show modes 0 16 Factory programs Show mode can run with or without sound active mode 1 Press the MENU button until SHND is displayed press ENTER 2 Sh X will now be displayed X representing a number between 0 16 Programs 1 16 are factory programs while Sh 0 is random mode Press the UP or DOWN buttons to find your desired show 3 When you have found your desired show press ENTER then press and hold the MENU button for at least 3 seconds to acti vate SOUN Sound Active mode 1 Press the MENU button until SOUN is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to activate sound active mode or OFF to deactivate sound active mode 3 Press ENTER and then press and hold the MENU button for at least 3 seconds to activate ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 11 Sweeper Beam LED System Menu SE
8. the controls on the rear panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables lf you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro S fessional sound and lighting stores Your cables Figure 1 should be made with a male and female XLR connector on either end ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 6 Sweeper Beam LED Set Up of the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Male Socket XLR Female Socket 1 e Figure 3 XLR Pin Configuration 2 Cold 1 1 Ground Pin 1 Ground Pin 2 Data Compliment negative 1 1 Pin 3 Data True positive s Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt res
9. until LED is displayed press ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 12 Sweeper Beam LED System Menu ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to keep the LED display on at all times or OFF to switch to have the LED display switch off after 10 seconds To make the display reappear press and hold the MENU button for at least 5 secs 3 Press ENTER to confirm To make the display reappear press and hold the MENU button for at least 5 secs REV This function is used in conjuction with 11 Chan nel mode and 15 Channel mode The direction in which the projector lenses light up can be reversed so that the LED line up can start at either end of the bar This feature is useful when the unit is installed in a reversed orientation so the unit itself does not have to be uninstalled and reversed Example When using 11 Channel mode Channel 4 LED 1 can start at either end of the bar depending on this functions set up 1 Press the MENU button until REV is displayed press ENTER 2 The display will show either YES or NO Press the UP or DOWN buttons to select YES which will have the projector lenses light up right to left or NO which will have the projec tor lenses light up left to right 3 Press ENTER to confirm TILT This function activates tilt inversion 1 Press the MENU button until
10. G 0 100 LENS 2 4 CHASES 6 DIMMING 0 100 LENS 3 0 7 NO FUNCTION 7 DIMMING 0 100 LENS 4 CHASE 1 CHASE 2 DIMMING 0 100 LENS 6 CHASE 3 DIMMING 0 100 LENS 7 CHASE 4 DIMMING 0 100 LENS 8 CHASE 5 CHASE 6 CHASE 7 CHASE 8 CHASE 9 CHASE 10 CHASE 11 CHASE 12 CHASE 13 CHASE 14 CHASE 15 CHASE 16 FULL ON 6 0 255 MASTER DIMMER 0 10096 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 19 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 20 Sweeper Beam LED 15 DMX Channel Mode Function 7 STROBING 0 15 NO FUNCTION 16 131 STROBING SLOW FAST 132 139 NO FUNCTION 140 181 SLOW OPEN FAST CLOSE 182 189 NO FUNCTION 190 231 SLOW CLOSE FAST OPEN 232 239 NO FUNCTION 240 247 RANDOM STROBING 248 255 NO FUNCTION 8 0 255 DIMMING 0 10096 LENS 1 9 DIMMING 0 100 LENS 2 10 DIMMING 0 100 LENS 3 11 DIMMING 0 100 LENS 4 DIMMING 0 100 LENS 5 DIMMING 0 100 LENS 6 DIMMING 0 100 LENS 7 DIMMING 0 100 LENS 8 Sweeper Beam LED Photometric Chart lux 26600 8190 3680 2070 1320 __ OOOO m O ou ces a e ET rua Fe e pe om O a Il SS 1 aa Distance m 0 1 2 3 4 5 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 21 Sweeper Beam LED Fuse Replacement
11. NS sound sensitivity control 1 Press the MENU button until SENS is displayed press ENTER 2 The display will show a number between 0 100 Press the UP or DOWN buttons to adjust the sound sensitivity O being the least sen sitive and 100 the most sensitive 3 Press the ENTER button to confirm DNST This mode can be used as a precaution mode that in case the DMX signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operat ing mode you would like the unit to return to when power is applied 1 Press the MENU button until DNST is displayed press ENTER 2 Either MAST BLND or LAST will be displayed Choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost MAST Master Slave If the DMX signal is lost or power is applied the unit will automatically go into Master Slave mode BLND Blackout If the DMX signal is lost or power is applied the unit will automatically go into stand by mode LAST Last State If the DMX signal is lost the fixture will stay in the last DMX set up If power is applied and this mode is set the unit will automatically go into the last DMX set up 3 Press ENTER to confirm your desired set up LED with this function you can have the LED display turn off after 10 seconds 1 Press the MENU button
12. ackage No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or imp
13. al operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 823 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 2 General Instructions Sweeper Beam LED To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Sweeper Beam LED Features DMX 512 Protocol 4 DMX Channel Modes 1 Channel Mode 6 Channel Mode 11 Channel Mode amp 15 Channel Mode 3 Operating Modes Sound Active Show Mode and DMX Control Internal Microphone Digital Display for Address and Function Setting UC3 Controller Not Included Sweeper Beam LED Warranty Registration The Sweeper Beam LED carries a 3 year 1095 days limited war ranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj
14. com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Sweeper Beam LED Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 3 Sweeper Beam LED Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of a
15. de Function SHOWS 0 7 BLACKOUT 8 22 SHOW 1 23 37 SHOW 2 38 52 SHOW 3 53 67 SHOW 4 68 82 SHOW 5 83 97 SHOW 6 98 112 SHOW 7 CHASES NO FUNCTION 8 22 CHASE 1 23 37 CHASE 2 38 52 CHASE 3 53 67 CHASE 4 113 127 128 142 143 157 158 172 173 187 188 202 203 217 218 232 233 247 248 255 SHOW 8 SHOW 9 SHOW 10 SHOW 11 SHOW 12 SHOW 13 SHOW 14 SHOW 15 SHOW 16 RANDOM SHOW 68 82 83 97 CHASE 5 CHASE 6 CHASE 7 CHASE 8 CHASE 9 CHASE 10 CHASE 11 CHASE 12 CHASE 13 CHASE 14 CHASE 15 CHASE 16 FULL ON 0 255 CHASE SPEED SLOW FAST 6 0 255 MASTER DIMMER 0 100 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 18 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 17 Sweeper Beam LED 11 DMX Channel Mode Sweeper Beam LED 15 DMX Channel Mode Function Function 1 n o 0 255 TILT 30 210 _ Emm MASTER DIMMER 0 100 2 TILT MOVEMENT MACRO STROBING NO FUNCTION NO FUNCTION TILT MOVEMENT MACRO 60 120 STROBING SLOW FAST TILT MOVEMENT MACRO 45 135 NO FUNCTION TILT MOVEMENT MACRO 30 150 SLOW OPEN FAST CLOSE TILT MOVEMENT MACRO 0 180 NO FUNCTION TILT MOVEMENT MACRO 30 210 SLOW CLOSE FAST OPEN TILT MOVEMENT MACRO 0 90 NO FUNCTION TILT MOVEMENT MACRO 90 180 RANDOM STROBING 3 TILT MOVEMENT MACRO SPEED NO FUNCTION 0 7 NO FUNCTION DIMMING 0 10096 LENS 1 8 255 SLOW FAST 5 DIMMIN
16. el of the unit 2 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 22 Sweeper Beam LED Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original p
17. ferent functions including blackout Show Mode In this mode you can choose 1 of 16 show modes to run 1 Tap the MENU button until SHND is displayed and press ENTER 2 Tap the UP or DOWN buttons until you find your desired show and press ENTER then press and hold MENU for 3 seconds to confirm See page 11 for more info 3 The optional UC3 Controller not included may be used to con trol different functions including blackout Sweeper Beam LED Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 9 fixtures maximum After 9 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 16 Sweeper Beam LED UC3 Control Blackout Blackout the unit Sweeper Beam LED 6 DMX Channel Mode Function TILT MOVEMENT MACRO NO FUNCTION TILT MOVEMENT MACRO 60 120 TILT MOVEMENT MACRO 45 135 TILT MOVEMENT MACRO 30 150 TILT MOVEMENT MACRO 0 180 TILT MOVEMENT MACRO 30 210 TILT MOVEMENT MACRO 0 90 TILT MOVEMENT MACRO 90 180 3 TILT MOVEMENT MACRO SPEED 8 255 SLOW FAST 4 0 7 1 Sound Strobe Full on 2 Auto Strobe Full on Select Shows Show 1 16 Mode Random Show LED OFF Show LED ON Sweeper Beam LED 1 DMX Channel Mo
18. hting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Sweeper Beam LED can be controlled via DMX 512 protocol The Sweeper Beam LED can be a 1 6 11 or 15 channel DMX unit The DMX address is set electronically using
19. istor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference It is always advisable Z p to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 7 Sweeper Beam LED Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor Ground Shield 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 Pin 3 Not Used Pin 4 Do Not Use Not Used o Pin 5 Do Not Use Sweeper Beam LED Installation The unit should be mounted using a mounting clamp not provided affixing it to the mounting bracket that is provided with the unit Always ensure that the unit is firmly fixed to avoid vibrati
20. n internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 22 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 4
21. niversal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Sweeper Beam LED can be a 1 6 11 or 15 DMX channel fixture See pages 17 21 for detailed description of the DMX val ues and traits ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 15 Sweeper Beam LED Operation 2 To control your fixture in DMX mode follow the set up procedures on pages 6 8 as well as the set up specifications that are includ ed with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instructions on page 10 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture For help operating in DMX mode consult the manual included with your DMX controller pude amp Sound Active Mode This mode allows either single unit several units linked together to run to the beat of the music 1 Tap the MENU button until SOUN is displayed and press ENTER 2 Tap the UP or DOWN buttons to choose either OFF or ON and press ENTER then press and hold MENU for 3 seconds to con firm To adjust sound sensitivity see page 12 3 The optional UC3 Controller not included may be used to con trol dif
22. on and slip ping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times the unit s weight Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture The equipment must be installed by a professional and it must be installed in a place where it is out of the reach of people s grasp ADJ Products LLC www adj com Sweeper Beam LED User Manual Page 8 Sweeper Beam LED System Menu DMX512 Address OL 1 Fr Master Slave Mode 1 Irc Channel Mode IF 1 tt C a 511 3 Angel Setting r r Show Mode 0 16 Sound Mode SEAS Sound Sense 0 100 LOFT 1 1 DMX State F o Fc LED 15 7 n DL Display Inversion DL Tilt Inversion ra n noa REV ES E Self Test 5 Fixture hours utr Software Version
23. rovements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps Laser Products 90 Day Limited Warranty
24. s On facebook com americandj twitter com americandj youtube com adjlighting
25. ture as a stand alone fixture or in a master slave confiugration This next section will detail the differences in the operating modes e Sound Active mode The fixture will react to sound chasing through the built in programs Show mode Choose 1 of 16 show modes to run e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the Elatione Show Designer Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture Set the Master unit to your desired operating mode 3 For the slave units press the MENU button until SLND is dis played and Press ENTER Set the slave units to either SL 1 or SL 2 4 The slave units will now follow the Master unit m U
Download Pdf Manuals
Related Search