Home
Model No. PE4-11R-03
Contents
1. 11 000 BTU Portable Air Conditioner with dehumidifier amp Fan PE4 11R 03 Operating Instructions Model No PE4A 11R 03 Soleus Air International Thank you for choosing a Soleus Air Portable Air Conditioner This owner s manual will provide you with valuable information necessary for the proper care and maintenance of your new product Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new Soleus Air Portable Air Conditioner For your own records please attach a copy of your sales receipt to this manual Also write the store name location date purchased and serial number below Store Name Location Date Purchased Serial Number located on back of unit ko An An _ _ e e QRO A IMPORTANT INSTRUCTIONS Before installing and using your portable air conditioner please read this owner s manual carefully Store this manual in a safe place for future reference 1 Always place the unit on a level surface 2 Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual 3 Maintain at least 10 inches 25 cm clearance space around this unit Do not block or cover air inlet or outlet grilles 4 The unit must be connected to a correctly grounded power supply 5 Do not start or stop the unit by inserting or pulling out the power
2. the air conditioner or attempt to reset the LCDI Plug Contact Soleus Air Customer Service for troubleshooting recommendations RESET TEST WARNING 1 DO NOT press the TEST button while the air conditioner is operating 2 The TEST and RESET buttons should not be used as ON and OFF switches 3 The cord and plug are not intended to offer protection to externally connected loads or supply circuits 4 The cord and plug are intended for indoor use only WINDOW KIT INSTALLATION Installation of the Venting Kit lineal a an FOR SINGLE HOSE PORTABLE AIR CONDITIONERS The venting kit must be installed in order for the unit to work correctly in the air conditioning mode The venting kit should not be used while the unit is heating or fanning The window kit has been designed to fit into most vertical and horizontal window openings The window kit can also be used in a sliding door 1 Choose a suitable location near a grounded electrical outlet and a suitable window or door Remove packaging and locate components figure a 2 Slide the exhaust connector over the discharge opening on the back of the unit figure b 3 Connect the exhaust hose to the exhaust connector aligning the fitted grove figure c 4 Open the window or door and adjust the length of the window kit to fit the opening figure d If necessary mark the kit and cut one end down to properly fit the opening figures e 8 f 5 Att
3. then press the SEND button to transmit the operation 5 Dry Press the DRY Button to engage dehumidifier mode Once DRY mode is selected choose the de sired fan speed and temperature then press the SEND button to transmit the operation 6 Fan Speed Press the FAN speed button to cycle through low medium and high fan speeds 7 Temperature Setting When the unit is in Air Conditioner mode you can select your desired temperature Press the F or F buttons to select your desired temperature setting The temperature on the LCD display will increase or decrease accordingly 12 REMOTE CONTROL OPERATING INSTRUCTIONS CONT 7 Sleep Mode See SLEEP MODE on page 9 8 Timer To program the timer press the TIMER button on the remote control to select the SET TIMER MODE To program the unit to automatically turn on make sure the unit is on then press the Hr Min buttons to select the desired time between 1 18 hours Once you have chosen the auto on time press the SEND button to transmit the time To program the unit to turn off automatically press the SLEEP button on the remote then press the Hr Min buttons to select the desired time for the unit to turn off 9 After the timer is set to automatically turn on the unit will shut off and turn on at the set time Once the SLEEP button is pressed the SET TIMER function will be disable and vice versa 13 CARE 8 MAINTENANCE Prior to all cleaning and maintenance plea
4. through the wall or out a window If mounting in the wall the height of the hole should be 16 to 50 inches 40cm to 130cm Front Plastic Pipe End Middle Plastic Pipe End Rear Clip B AN v DN EE LCDI POWER CORD AND PLUG This air conditioner is equipped with an LCDI Leakage Current Detection and Interruption power cord and plug as required by US National Electric Code 440 65 This cord consists of a length of shielded flexible cord with no termination on the load side and a LCDI attachment plug on the line side The LCDI power cord and plug will remove the supply source via electrical disconnect circuit trip if the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value The cord will remain de energized until the devise has been manually reset This is intended to reduce the risk of a fire in the power cord or combustible materials nearby The cord shields are not grounded and they must be considered a shock hazards if exposed The cord shield must not be connected to ground or to any exposed metal The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly To test 1 Plug power cord into wall outlet 2 Press TEST Button circuit should trip cutting power to the air conditioner 3 Press RESET button for use If a test is performed and the indicator light remains ON current leakage has been detected Do not use
5. ach the window kit adapter to the window kit figure g 6 Place the window kit back into the window and attach the exhaust hose to the window kit adapter figures h amp i Close the window tightly figure j Your Portable Air Conditioner is now ready to cool NOTE When using the venting system keep the exhaust hose as straight as possible The exhaust hose can be shortened but it is not recommended to increase the length of the exhaust hose Do not use an extension cord with your portable air conditioner CONTROL PANEL DISPLAY amp OPERATING INSTRUCTIONS CONTROL PANEL amp LCD DISPLAY Remote Control window Z SET TEMP ON OFF LCDscreen SET TIMER O do e TEMP SET SLEEP MODE LCD Display TIMER display G see Y Jedi FAN m LOW MD HGH 0 1 kore DRY Fizi SET TEMP SET TIME SET TIMERON OFF FAN display OPERATING INSTRUCTIONS CONTROL PANEL BUTTONS Refer to the images on page 9 1 2 3 4 5 6 Power On and Off Press the ON OFF button once to manually turn the unit on Press the ON OFF button once more to turn the unit off Mode Selection Press the MODE Button repeatedly to cycle between the different modes Auto mode Air Conditioner Dehumidifier and Fan Fan Speed Control Press the FAN SPEED Button to cycle through the different fan speeds High Medium and low The fan speed can be visually distinguished by the speed of the digital ai
6. defrost There is a current problem with the power supply There is a problem with the air condi tioner The condensate holding tank Insert the power plug tightly in the electrical outlet Replace the power plug or socket Replace the fuse Cancel the Set Timer operation Set the unit temperature below the room temperature if you wish for the area to be cooler If not leave tem perature setting alone The unit is currently defrosting and will resume normal operation when defrost is complete The unit is currently defrosting and will resume normal operation when defrost is complete Turn off the unit and unplug the power cord from the electrical outlet for 10 minutes After 10 minutes plug the unit back in and try to start the unit If El is still displayed contact Soleus Air Empty the condensate holding tank If H8 is still displayed the unit may be malfunctioning and you should contact Soleus Air 15 EI WARRANTY One Year Limited Warranty Soleus International Inc warrants the accompanying Soleus Air PE4 11R 03 Portable Air Conditioner to be free of de fects in material and workmanship for the applications specified in its operation instruction for a period of ONE 1 year from the date of original retail purchase in the United States If the unit exhibits a defect in normal use Soleus International Inc will at its option either repair or replace it free of charge within a reasonable t
7. desired room temperature appears on the control panel display The temperature ranges from 61 F 86F 16 Gaal 6 Select the desired fan speed by pressing the FAN button NOTE During hot days the unit will cool the room most efficiently by setting the temperature at the lowest setting and the fan speed on high Reducing the length of the exhaust duct insulating the exhaust hose and window kit and keeping direct sunlight to a minimum will also improve the cooling efficiency NOTE When the unit is running on cooling mode the exhaust hoses are required and must be vented outside using the supplied window kit Dehumidifier Mode 1 Install the exhaust hoses and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the ON OFF Button on the control panel 4 Press the MODE button until the DRY icon appears on the control panel display NOTE The unit operates at low fan speed during dehumidifier mode The unit cools room slightly during the dehumidification Keep the windows and doors closed to aid the effectiveness of the unit in removing the moisture from the room NOTE When the unit is running in dehumidifier mode the exhaust hoses are required and must be vented outside using the supplied window kit NOTE The unit will not perform in dehumidifier mode when the room temperature is lower than 6 1F Fan Mode 1 Plug the Power Cord into an electrical out
8. drain hole The condensate water will drain out automatically When the drain pan is full replace the rubber plug into the drainage hole to stop the water flow Empty the drain pan Repeat until all the water is emptied 4 Ifthe unit is placed close to a drain you may attach the drain hose and drain the water into the drain or pan Once the water container has been emptied replace the rubber plug into the drain hole firmly Do not allow the water to drip continuously into the drain pan as it might easily overflow Drainage Pipe RUbberPlug 11 OPERATING THE UNIT USING THE REMOTE CONTROL REMOTE CONTROL LCD Display shows all settings FAN SPEED DRY MODE TIMER BUTTON MODE BUTTON TEMP SET BUTTONS n gt gt SLEEP MODE TIMER SET BUTTONS ON OFF BUTTON REMOTE CONTROL OPERATING INSTRUCTIONS 1 Power On and Off Press the I O button on the remote to turn the unit on or off 2 Send Press this button to transmit the chosen operation This button must be pressed after every operation change using the remote 3 Mode Selection Press the MODE Button repeatedly to cycle between the different modes Auto Air Conditioner Dehumidifier and Fan only mode NOTE Heat mode can be selected using the re mote control however heat mode is not functional on this unit 4 Cooling Mode Press the MODE button to choose the cooling option Once cooling mode is selected choose the desired fan speed and temperature and
9. ime after the unit is returned during the warranty period As a condition to any warranty service obligation the consumer must present this Warranty Certificate along with a copy of the original purchase invoice THIS WARRANTY DOES NOT COVER e Damage accidental or otherwise to the unit while in the possession of a consumer not caused by a defect in material or workmanship e Damage caused by consumer misuse tampering or failure to follow the care and special handling provisions in the instructions e Damage to the finish of the case or other appearance parts caused by wear e Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna tional Inc e Freight and Insurance cost for the warranty service ALL WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO ONE YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY SOLEUS INTERNATIONAL INC DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT SHALL SOLEUS INTERNATIONAL INC S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT This warranty covers only new products purchased from our authorized dealers or retailers It does not cover used sal vaged or refurbished products As some states do not allow the limitation or exclusion of incidental or consequential damages or do not allow limitation on implied warranties the ab
10. let 2 Turn on the unit by pressing the ON OFF button on the control panel 3 Press the MODE button until the FAN icon appears on the control panel display 4 Select the fan speed by pressing the FAN button NOTE It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in fan mode 10 Auto Mode 1 Install the exhaust hoses and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the ON OFF button on the control panel 4 Press the MODE button until the AUTO icon appears on the control panel display Select the fan speed by pressing the FAN button NOTE During AUTO mode the unit operates in Dehumidifier mode when the room temperature is between 68 F to 80 F And Air Conditioner mode when the room temperature is above 80 F Emergency Condensate Holding Tank When the unit is in cooling mode unwanted water is extracted from the air Most of this water is used to cool the unit and make it run more efficiently When the unit is used in extremely humid environments water will collect in a water container at the bottom of the unit When the water container is full the compressor will stop but the fan will continue to run 1 Turn the unit off Do not move the unit when the water container is full Place the drain pan accessory under the drainage port at the back of the unit 3 Remove the rubber plug from the
11. ork properly MODEL PE4 11R 03 COOLING CAPACITY 11 000 BTU H DEHUMIDIFYING CAPACITY 50 pts per Day COOLING POWER 1050 W AIR FLOW VOLUME 260 CFM 115 V 60 HZ POWER SOURCE 8 5AMP SOUND PRESSURE LEVEL 60 dB A NET WEIGHT 70 5 Lbs OPERATING E o TEMPERATURE 22599 ASSEMBLED 17 7 W X 33 1 H X14 6 D DIMENSIONS PACKAGE 27 2 WX 3425 HX 16 7 D DISCLAIMER ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER S MANUAL ARE THE PRESENTATION OF THE MANUFACTURER SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN PRODUCT DIAGRAM Y t 2 m U a MARIANAS 2 MA V gt M MAA io re B gt A A oo Y z hb AAA AN Ye ANY SS y YA See ov awe o ee SS e m a LL FRONT BACK INSTALLATION SELECTING THE LOCATION Place the unit on a flat surface in an area where the outlets are not obstructed Place the unit at least 20 away from all adjacent walls MOUNTING THE EXHAUST HOSE Slide the square front end of the exhaust duct over the hot air outlet on the back of the unit The exhaust hose should be kept as short and straight as possible Prevent any sharp bends in the exhaust hose as this will trap hot exhaust air and cause the unit to run less efficiently The hot exhaust air can be vented
12. ove limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state For Technical Support and Warranty Service Please Call 888 876 5387 Or Write To Soleus International Inc 9451 Telstar Ave El Monte CA 91731 USA www soleusair com 16
13. plug 6 Do not use an adapter plug or extension cord 7 Do not use the unit in the immediate surroundings of a bath a shower or a swimming pool 8 Do not insert anything into the air outlet Do not obstruct air inlet or outlet grills unless instructed by this manual 9 Do not let children play near this unit 10 Always inspect the cord for signs of damage before use If the power cord is damaged it must be replaced by the manufacturer or a qualified service technician 11 When cleaning the unit always turn the unit off and unplug the power cord ss PACKAGE CONTENTS Portable Air Conditioner Exhaust Hoses 1 Hose Adapters 1 Window Kit Adapter 1 Remote Control AAA Batteries 2 Window Kit 3 Sliding Panels 1 single hose panel 2 extension panels Owner s Manual Wall Cover 1 the cap covers the whole on the wall or window SSS oye AAA a SPECIFICATIONS e The cooling capacity is measured at an ambient temperature of DB 86 F WB 78 F e Noise level is measured at a distance of 3 28 ft away from the front of the unit when the unit is in cooling mode e Power consumption is measured when the fan runs at the highest speed setting e These specifications are for reference only For actual data please refer to the rating label on the back of the unit e Ifthe environment temperature is higher than the max operating temperature or lower than the minimum operating temperature the air conditioner may not w
14. r segments progressing out from the windmill fan image on the Multi color display There is an additional auto speed setting that is enabled in only heating and cooling modes This speed is next setting after low when press ing the speed control button The speeds will cycle through in this order Low Medium High Auto Each change in speed will be associated with a beep sound from the unit Set Temp Select the desired temperature by pressing either Y or A on the SET TEMP button when using the unit in COOL or HEAT mode Timer To program the timer press the A or W buttons on the SET TIMER button to set the timer To set the unit to turn on automatically turn the unit off and select the desired time for the unit to turn on To set the unit to turn off automatically turn the unit on then set the timer to turn the unit off at the desired time Sleep When the unit is running press the SLEEP button once to start the sleep operation Press the SLEEP button once more to stop sleep operation NOTE Sleep operation does not work when the unit is in AUTO mode OPERATING THE UNIT USING THE CONTROL PANEL Air Conditioner Mode 1 Install the exhaust hose and window kit properly see pages 7 amp 8 2 Plug the Power Cord into an electrical outlet 3 Turn on the unit by pressing the ON OFF button on the control panel 4 Press the Mode button until the COOL icon appears on the LCD display 5 Press the A or Y buttons until the
15. se unplug the air conditioner from the outlet Cleaning the air filter 1 Press down on the two latches hooks on top of the filter and remove the air intake grill from the air condi tioner 2 Remove the filter from the air intake grill 3 Wash the filter with a mild soap You may spray off the unit or immerse in water 4 Dry off this filter with a cloth or let it dry in the shade NOTE Do not use hot water when cleaning the filter It could cause the filter to deform and become unusable Air inlet grille Cleaning the air conditioner Please use a damp cloth or rag with warm water to wipe down the unit Do not use gasoline oil or household cleaners when cling the unit Before cleaning make sure the unit is unplugged Ba TROUBLESHOOTING The Air Conditioner Does Not Start The LCD display the number for the timer but 1t does not work The unit is set to COOLING mode but the airflow from the air conditioner is not cool The unit is set to DRY Dehumidifier mode and the airflow from the air condi tioner is not cool The LCD displays El The LCD displays H8 The Power Supply is not Connected to an outlet The Power plug is not inserted tightly to an outlet There is a malfunction with the power plug or electrical outlet and or fuse Is the Timer On in operation The room temperature is lower than the set temperature on the unit The evaporator needs to defrost The evaporator needs to
Download Pdf Manuals
Related Search
Related Contents
Verbatim Store `n` Go® Pro USB Flash Drive Quick Guide Kit de controles APTIMA Philips 46PFL5508G 46" Full HD 3D compatibility Smart TV Wi-Fi Black user and maintenance manual Telex AUDIOCOM BP-2000 User's Manual Ê800-12741SP(Š References marked on instrument or in instruction manual: TEC APO 140 - Baader Planetarium AHB-10M Manuale Tecnico CE - Testina M28E Copyright © All rights reserved.
Failed to retrieve file