INTRODUCTION USER`S MANUAL HOW TO
Contents
1. e Don t panic stay calm Follow your family escape plan e Get out of the house as quickly as possible Don t stop to get dressed or collect anything e Feel doors with the back of your hand before opening them If a door is cool open it slowly Don t open a hot door Keep doors and windows closed unless you must escape through them e Cover your nose and mouth with a cloth preferably damp Take short shallow breaths e Meet at your planned meeting place outside your home and do a head count to make sure everybody got out safely e Call the Fire Department as soon as possible from outside Give your address then your name e Never go back inside a burning building for any reason e Contact your Fire Department for ideas on making your home safer AWARNING Alarms have various limitations See General Limitations of Smoke CO Alarms for details USING THE SILENCE FEATURES AWARNING Never remove the batteries to quiet an unwanted alarm Removing the batteries disables the alarm and removes your protection The Silence Feature is intended to temporarily silence the horn while you identify and correct the problem Do not use the Silence Feature in emergency situations It will not correct a CO problem or extinguish a fire The Silence Feature can temporarily quiet an unwanted alarm for several minutes You can silence this Smoke CO Alarm by pressing the Test Silence button on the alarm cover for at least 3 5 seconds2. After the Test Silence button is released the Alarm Voice will say Horn silenced detector active The Red LED blinks during the silence mode When the CO Alarm is Silenced When the Smoke Alarm is Silenced The CO alarm will remain silent for up to 4 minutes The Smoke Alarm will remain silent for up to 15 minutes then return to normal operation After 4 minutes if CO levels remain potentially dangerous the horn will start sounding again If the smoke has not cleared or continues to increase the device will go back into alarm SILENCING THE LOW BATTERY WARNING This Silence Feature can temporarily quiet the low battery warning chirp for up to 8 hours if AC power is present Press the Test Silence button on the Alarm cover until you hear the acknowledge chirp Once the low battery warning chirp silence feature is activated the unit continues to flash the green light once a minute for 8 hours After 8 hours the low battery chirp will resume The Alarm will continue to operate as long as AC power is supplied However replace the batteries as soon as possible to maintain protection in event of a power outage To deactivate this feature Press the Test Silence button again The unit will go into Test Mode and the low battery warning will resume LED flashes and unit sounds chirp once a minute To silence Alarms in an interconnected series To silence an interconnected series
3. Constant Green CO LED Off When You Test the Alarm Voice Testing Horn 3 beeps pause 3 beeps Voice Warning evacuate smoke in Location example Basement Evacuate Power Smoke LED Flashes Red in sync with the horn pattern CO LED Off followed by Horn 4 fast beeps pause 4 fast beeps Voice Warning evacuate carbon monoxide in Location example Basement Evacuate Pause Highest carbon monoxide level was CO level example _0_ ppm Power Smoke LED Off CO LED Flashes Red in sync with the horn pattern If Battery Becomes Low or is Missing Voice Replace battery in Location example Basement Repeated every 5 hours Horn chirps once a minute Power Smoke LED Flashes Green On for 2 seconds Off for 2 seconds Low Battery Latch is now engaged CO LED Off If Alarm is Not Operating Properly MALFUNCTION SIGNAL Voice Detector error in Location example Basement please see manual Repeated every 5 hours Horn 3 chirps every minute Power Smoke LED 3 Flashes approximately once a minute CO LED Off Alarm has reached its End of Life Voice Detector error in Location example Basement please see manual Repeated every 5 hours Horn 5 chirps every minute Power Smoke LED 5 Flashes approximately once a minute CO LED Off Alarm Levels of CO are Detected Horn 4 fast beeps pause 4 fast beeps pause Voice Warning evacuate carbon m
4. you must disconnect it from the AC power before unlocking the battery compartment ADANGER ELECTRICAL SHOCK HAZARD Turn off the power to the area where the Alarm is installed before removing it from the mounting bracket Failure to turn off the power first may result in serious electrical shock injury or death a l AWARNING f a eean pliers detach one loekiNa PIN font tig mounting Always discharge the branch circuit before servicing an AC or AC DC racket Alarm First turn off the AC power at the circuit breaker or fuse box Next remove the battery from Alarms with battery back up Finally press and hold the Test Silence button for 5 10 seconds to discharge the branch circuit 1 Remove the Alarm from the mounting bracket If the unit is locked to the bracket see the section To Unlock the Mounting Bracket 2 Disconnect the power connector by gently prying it away from the back of the Alarm 3 Insert a flathead screwdriver under the head of the locking pin and gently pry it out of the battery compartment lock If you plan to relock the battery compartment save the locking pin 4 To relock the battery compartment close the battery door and reinsert locking pin in lock 5 Reconnect the power connector to the back of the Alarm reattach the Smoke Alarm to the mounting bracket and restore the power IMPORTANT When replacing the batteries always test the Alarm before relocking the battery compartmen
5. Programming This Alarm 4 5 What You Will See and Hear With This Alarm 5 LOCKING Features lt 6 chen cance es salen ee eee odes eee ee a ees 5 6 Regular Maintenance 000 ccc eee eee 6 If Your Smoke CO Alarm Sounds 00000c seen eens 7 8 What To Do First Identify The Type Of Alarm T If the CO Alarm SoundS nnn anaana aaan 7 If the Smoke Alarm Sounds nannan anaa 7 Using the Silence Features 0 ccc 7 8 Latching Features occ cvouwds eo ced bedencced ceed eens eee 8 Smart Interconnect Feature aaan anaa ees 8 What You Need To Know About CO 0 cece eee eee eee 8 What is COO iss sae wee eaen annn a E Ven bees eeee erence es 8 Symptoms of CO Poisoning sg ot0dvdessee ee ee se eee eee 8 Finding the Source of CO After an Alarm 000000 8 Potential Sources of CO inthe Home 0 000 eee 8 How Can Protect My Family From CO Poisoning 9 Regulatory Information For Smoke CO Alarms 9 10 Regulatory Information for CO Alarms 000000 ees 9 Regulatory Information for Smoke Alarms 005 9 Recommended Locations for Smoke Alarms 9 Agency Placement Recommendations naana aoaaa anna 10 About Smoke Alarms nnn annann 10 Special Compliance Considerations 02220000000e 10 General Limitations Of Smoke CO Alarms 11 12 Troubleshooting G
6. Smoke Alarm portion of this device is not intended to alert hearing impaired residents Special purpose Smoke Alarms should be installed for hearing impaired residents CO Alarms are not yet available for the hearing impaired Smoke CO Alarms may not waken all individuals Practice the escape plan at least twice a year making sure that everyone is involved from kids to grandparents Allow children to master fire escape planning and practice before holding a fire drill at night when they are sleeping If children or others do not readily waken to the sound of the Smoke CO Alarm or if there are infants or family members with mobility limitations make sure that someone is assigned to assist them in fire drill and in the event of an emergency It is recommended that you hold a fire drill while family members are sleeping in order to determine their response to the sound of the Smoke CO Alarm while sleeping and to determine whether they may need assistance in the event of an emergency Smoke CO Alarms cannot work without power Battery operated units cannot work if the batteries are missing disconnected or dead if the wrong type of batteries are used or if the batteries are not installed correctly AC units cannot work if the AC power is cut off for any reason open fuse or circuit breaker failure along a power line or at a power station electrical fire that burns the electrical wires etc If you are concerned about the limitations of ba
7. duration of the above warranty Some states provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province How to Obtain Warranty Service Service If service is required do not return the product to your retailer In order to obtain warranty service contact the Consumer Affairs Division at 1 800 323 9005 7 30 AM 5 00 PM Central Standard Time Monday through Friday To assist us in serving you please have the model number and date of purchase available when calling For Warranty Service return to BRK Brands Inc 25 Spur Drive El Paso TX 79906 Battery BRK Brands Inc make no warranty express or implied written or oral including that of merchantability or fitness for any particular purpose with respect to battery TABLE OF CONTENTS Introd cti n siaaa cence eee eee ee eee eda ane a ana a a es 1 Installation oaiae a erate ie cain ay mcce carom cn eed wt we wee wo mm wl ae 2 4 Where to Install This Alarm nnana nnana aaa 2 Where This Alarm Should NOT Be Installed 2 How to Install This Smoke CO Alarm 00000 0 eee 3 4 Weekly Testing sx scuwectseddccchur hed decd doede eee eusttes 2 3 Step By Step Guide to
8. is not a suitable substitute for complete fire detection systems in warehouses industrial facilities commercial buildings and special purpose non residential buildings which require special fire detection and alarm systems Depending on the building codes in your area this unit may be used to provide additional protection in these facilities The following information applies to all five types of buildings listed below In new construction most building codes require the use of AC or AC DC powered Smoke Alarms only AC AC DC DC or Wireless DC powered Smoke Alarms can be used in existing construction as specified by local building codes Refer to NFPA 72 National Fire Alarm Code and NFPA 101 Life Safety Code local building codes or consult your Fire Department for detailed fire protection requirements in buildings not defined as households 1 Single Family Residence Single family home townhouse It is recommended this unit be installed on every level of the home in every bedroom and in each bedroom hallway 2 Multi Family or Mixed Occupant Residence Apartment building condominium This unit is suitable for use in individual apartments or condos provided a primary fire detection system already exists to meet fire detection requirements in common areas like lobbies hallways or porches Using this unit in common areas may not provide sufficient warning to all residents or meet local fire protection ordinances reg
9. may not hear the alarm horn if the sound is blocked by distance or closed doors Noise from traffic stereo radio television air conditioner or other appliances may also prevent alert persons from hearing the alarm horn This Smoke CO Alarm is not intended for people who are hearing impaired The Alarm may not have time to alarm before the fire itself causes damage injury or death since smoke from some fires may not reach the unit immediately Examples of this include persons smoking in bed children playing with matches or fires caused by violent explosions resulting from escaping gas This Smoke CO Alarm is not a substitute for life insurance Though this Smoke CO Alarm warns against increasing CO levels or the presence of smoke BRK Brands Inc does not warrant or imply in any way that they will protect lives Homeowners and renters must still insure their lives This Smoke CO Alarm has a limited life Although this Smoke CO Alarm and all of its parts have passed many stringent tests and are designed to be as reliable as possible any of these parts could fail at any time Therefore you must test this device weekly The unit should be replaced immediately if it is not operating properly This Smoke CO Alarm is not foolproof Like all other electronic devices this Smoke CO Alarm has limitations It can only detect smoke or CO that reaches the sensors It may not give early warning of the source of smoke or CO is in a remote part of
10. the home away from the alarm device TROUBLESHOOTING GUIDE If the Alarm Problem Horn chirps about once per minute Green Smoke CO LED flashes Green On for 2 seconds Off for 2 seconds Low Battery Latch is engaged Voice Replace battery in Location every 5 hours Horn sounds 3 chirps every minute Voice Detector error in Location example Basement please see manual repeated every 5 hours LED has 3 flashes with chirps The light flashes RED and the horn sounds 5 chirps every minute Voice Detector error in Location example Basement please see manual repeated every 5 hours Carbon Monoxide Alarm ONLY CO Alarm goes back into alarm 4 minutes after CO levels indicate a potentially dangerous you Silence it situation CO Alarm sounds frequently even though no high levels of CO are revealed in an investigation details Smoke Alarm ONLY Smoke Alarm sounds when no smoke is visible For a list of acceptable replacement batteries see Regular Maintenance Low battery warning END OF LIFE SIGNAL Alarm needs to be replaced The CO Alarm may be improperly located Refer to Where to Install This Alarm for Unwanted alarm may be caused by non emergency source like cooking smoke You should Install two new AA batteries MALFUNCTION SIGNAL Device is not working Units under warranty should be returned to properly and needs to be replaced manufactu
11. wires in the junction box to the orange interconnect wire Never cross hot and neutral wires between Alarms 3 Plug the power connector into the back of the Alarm 4 Activate the battery back up by removing the Pull to Activate Battery Back Up tab Or install battery back up Battery back up cannot work until you install the battery in the correct position Match a ag to a ad and eo to 5 Position the base of the Alarm over the mounting bracket and turn the Alarm clockwise right until the unit is in place If wall mounted adjust unit so words are level 6 Check all connections AWARNING Improper wiring of the power connector or the wiring leading to the power connector will cause damage to the Alarm and may lead to a non functioning Alarm STAND ALONE ALARM ONLY e If you are only installing one Alarm restore power to the junction box INTERCONNECTED UNITS ONLY e If you are interconnecting multiple Alarms repeat steps 1 5 for each Alarm in the series When you are finished restore power to the junction box ADANGER ELECTRICAL SHOCK HAZARD Do not restore power until all Alarms are completely installed Restoring power before installation is complete may result in serious electrical shock injury or death 7 Make sure the Alarm is receiving AC power Under normal operation the Green power indicator light will shine continuously 8 If the Green power indicator light does not light TUR
12. you are not sure about your inverter or UPS type please consult with the manufacturer to verify Smoke Alarms for the hearing impaired Special purpose Smoke Alarms should be installed for the hearing impaired They include a visual alarm and an audible alarm horn and meet the requirements of the Americans With Disabilities Act Can be interconnected so if one unit senses smoke all units alarm Smoke alarms are not to be used with detector guards unless the combination has been evaluated and found suitable for that purpose All these Smoke Alarms are designed to provide early warning of fires if located installed and cared for as described in the user s manual and if smoke reaches the Alarm If you are unsure which type of Smoke Alarm to install refer the National Fire Protection Association NFPA Standard 72 National Fire Alarm Code and NFPA 101 Life Safety Code National Fire Protection Association One Batterymarch Park Quincy MA 02269 9101 Local building codes may also require specific units in new construction or in different areas of the home SPECIAL COMPLIANCE CONSIDERATIONS AWARNING This unit alone is not a suitable substitute for complete fire detection systems in places housing many people like apartment buildings condominiums hotels motels dormitories hospitals long term health care facilities nursing homes day care facilities or group homes of any kind even if they were once single family homes It
13. ENCE FEATURE BEDROOM 0 BEDROOM co alarms e BOTH OR COMBINATION SMOKE CO ALARMS Suggested locations are based on NFPA recommendations NFPA 72 for Smoke Alarms and NFPA 720 for Carbon Monoxide Alarms Always refer to national and local codes before beginning any installation In new construction AC and AC DC smoke alarms MUST be interconnected to meet NFPA recommendations e When installing on the wall the top edge of Smoke Alarms should be placed between 4 inches 102 mm and 12 inches 305 mm from the wall ceiling line e When installing on the ceiling place the alarm as close to the center as possible e In either case install at least 4 inches 102 mm from where the wall and ceiling meet See Avoiding Dead Air Spaces for more information NOTE For any location make sure no door or other obstruction could keep carbon monoxide or smoke from reaching the Alarm Installing Smoke CO Alarms in Mobile Homes For minimum security install one Smoke CO Alarm as close to each sleeping area as possible For more security put one unit in each room Many older mobile homes especially those built before 1978 have little or no insulation If your mobile home is not well insulated or if you are unsure of the amount of insulation it is important to install units on inside walls only WHERE THIS ALARM SHOULD NOT BE INSTALLED Do NOT locate this Smoke CO Alarm e In garag
14. N OFF POWER TO THE JUNCTION BOX and recheck all connections If all connections are correct and the Green power indicator still does not light when you restore the power the unit should be replaced immediately 9 Test each Smoke Alarm Press and hold the Test Silence button until the unit alarms When testing a series of interconnected units you must test each unit individually Make sure all units alarm when each one is tested ADANGER If any unit in the series does not alarm TURN OFF POWER and recheck connections If it does not alarm when you restore power replace it immediately WEEKLY TESTING AWARNING e NEVER use an open flame of any kind to test this unit You might accidentally damage or set fire to the unit or to your home The built in test switch accurately tests the unit s operation as required by Underwriters Laboratories Inc UL NEVER use vehicle exhaust Exhaust may cause permanent damage and voids your warranty e If the Alarm ever fails to test properly replace it immediately Products under warranty may be returned to the manufacturer for replacement See Limited Warranty at the end of this manual A CAUTION It is important to test this unit every week to make sure it is working properly Using the test button is Ps the recommended way to test this Smoke CO Alarm q You can test this Smoke CO Alarm by pressing and holding the Test Silence button on the Alarm cover until Alarm Voice says
15. ON FOR SMOKE ALARMS RECOMMENDED LOCATIONS FOR SMOKE ALARMS Installing Smoke Alarms in Single Family Residences The National Fire Protection Association NFPA recommends one Smoke Alarm on every floor in every sleeping area and in every bed room In new construction the Smoke Alarms must be AC powered and interconnected See Agency Placement Recommendations for details For additional coverage it is recommended that you install a Smoke Alarm in all rooms halls storage areas finished attics and basements where temperatures normally remain between 40 F 4 C and 100 F 38 C Make sure no door or other obstruction could keep smoke from reaching the Smoke Alarms More specifically install Smoke Alarms e On every level of your home including finished attics and basements e Inside every bedroom especially if people sleep with the door partly or completely closed e Inthe hall near every sleeping area If your home has multiple sleeping areas install a unit in each If a hall is more than 40 feet long 12 meters install a unit at each end e At the top of the first to second floor stairway and at the bottom of the basement stairway IMPORTANT Specific requirements for Smoke Alarm installation vary from state to state and from region to region Check with your local Fire Department for current requirements in your area It is recommended AC or AC DC units be interconnected for added protection BATTERY
16. OPERATED AND WIRELESS HARDWIRED BEDROOM HALL BEDROOM KEY SMOKE ALARMS KITCHEN LIVING ROOM z L r u S oe FINISHED BASEMENT MULTI STORY RESIDENCE gt l FINISHED BASEMENT HARDWIRED INTERCONNECTED WIRELESS INTERCONNECTED ALARMS KITCHEN DINING ROOM DINING ROOM 1 STORY RESIDENCE INSTALLING SMOKE ALARMS IN MOBILE HOMES For minimum security install one Smoke Alarm as close to each sleeping area as possible For more security put one unit in each room Many older mobile homes especially those built before 1978 have little or no insulation If your mobile home is not well insulated or if you are unsure of the amount of insulation it is important to install units on inside walls only Smoke Alarms should be installed where temperatures normally remain between 40 F 4 C and 100 F 38 r amp CO ALARMS BOTH OR KITCHEN ee COMBINATION SMOKE CO ALARMS o ONELINKe ENABLED A WIRELESS ALARMS BEDROOM AC OR AC DC ALARMS AGENCY PLACEMENT RECOMMENDATIONS Standards Underwriters Laboratories Inc Single and Multiple Station Smoke Alarms 217 NFPA 72 National Fire Code Chapter 11 For your information the National Fire Protection Association s Standard 72 reads as follows 11 5 1 One and Two Family Dwelling Units 11 5 1 1 Smoke Detection Where required by applicable laws codes or standards for the specified occup
17. Testing typically 3 5 seconds During testing you will see and hear the following sequence e The Alarm Voice will say Testing The Horn will sound 3 beeps pause 3 beeps The Alarm Voice will say Warning evacuate smoke in Location example Basement Evacuate The Power Smoke LED flashes Red and the CO LED will be Off e Next the Horn will sound 4 beeps pause 4 beeps The Alarm Voice will say Warning evacuate carbon monoxide in Location example Basement Evacuate The Power Smoke LED will be Off and the CO LED flashes Red If the unit does not alarm make sure the batteries are correctly installed and test again If the unit still does not alarm replace it immediately 3 The Parts of This Unit 1 Mounting Bracket 2 Mounting Slots 3 Locking Pins break out of bracket 4 Hot Black AC Wire 5 Neutral White AC Wire 6 Interconnect Orange Wire 7 Quick Connect Power Connector 8 Turn this way to remove from bracket 9 Turn this way to attach to bracket 10 Slide Out Battery Drawer Special Requirements For Interconnected Alarms AWARNING e Failure to meet any of the above requirements could damage the units and cause them to malfunction removing your protection e AC and AC DC Alarms can be interconnected Under AC power all units will alarm when one senses smoke or CO When power is interrupted only the AC DC units in the series will continue to send a
18. USER S MANUAL m i SMOKE amp CARBON First Alert MONOXIDE ALARM AC Powered Smoke amp Carbon Monoxide Alarm Features Exclusive Voice with Programmable Location Voice Warnin 5 Two Latching Features Ce ar Smart Interconnect Optipath 360 Technology a Two Silence Features Alkaline Battery Backup LISTED TO UL 217 and UL 2034 STANDARDS Model SC7010BV Printed in Mexico M08 0183 006 K1 09 10 IMPORTANT PLEASE READ CAREFULLY AND SAVE This user s manual contains important information about your Alarm s operation If you are installing the Alarm for use by others you must leave this manual or a copy of it with the end user INTRODUCTION Thank you for choosing First Alert for your Smoke and Carbon Monoxide Alarm needs You have purchased a state of the art Smoke amp Carbon Monoxide Alarm designed to provide you with early warning of a fire or Carbon Monoxide Key features include Smoke amp Carbon Monoxide Combination Alarm One alarm protects against two deadly household threats Exclusive Voice Warning with Location will tell you the preprogrammed location of the initiating unit and danger detected Programmable up to 11 locations ex basement When alarms sounds if programmed for basement it will say Warning evacuate smoke in basement Spread Spectrum Horn Tone Lower and varying horn frequency makes it easier for elderly with normal age related hearing loss to hear horn Sweeps thro
19. acement batteries listed below The unit may not operate properly with other batteries Never use rechargeable batteries since they may not provide a constant charge This unit has been designed to be as maintenance free as possible but there are a few simple things you must do to keep it working properly e Test it at least once a week e Clean the Smoke CO Alarm at least once a month gently vacuum the outside of the Smoke CO Alarm using your household vacuum s soft brush attachment Test the Smoke CO Alarm Never use water cleaners or solvents since they may damage the unit e If the Smoke CO Alarm becomes contaminated by excessive dirt dust and or grime and cannot be cleaned to avoid unwanted alarms replace the unit immediately e Relocate the unit if it sounds frequent unwanted alarms See Where This Alarm Should Not Be Installed for details e When the battery back up becomes weak the Alarm will chirp about once a minute the low battery warning and the Voice will say Replace battery in Location example Basement Repeated every 5 hours This warning should last 7 days but you should replace the battery immediately to continue your protection The Low Battery Latch feature will be engaged The Green Power Smoke LED will flash On for 2 seconds Off for 2 seconds Choosing a replacement battery Your Smoke CO Alarm requires two AA Energizer E91 batteries These batteries are available at ma
20. aches e An exposure to 400 ppm of CO may cause headaches in average healthy adults after 35 minutes but can cause death after 2 hours Standards Underwriters Laboratories Inc Single and Multiple Station carbon monoxide alarms UL2034 According to Underwriters Laboratories Inc UL2034 Section 1 1 2 Carbon monoxide alarms covered by these requirements are intended to respond to the presence of carbon monoxide from sources such as but not limited to exhaust from internal combustion engines abnormal operation of fuel fired appliances and fireplaces CO Alarms are intended to alarm at carbon monoxide levels below those that could cause a loss of ability to react to the dangers of Carbon Monoxide exposure This CO Alarm monitors the air at the Alarm and is designed to alarm before CO levels become life threatening This allows you precious time to leave the house and correct the problem This is only possible if Alarms are located installed and maintained as described in this manual Gas Detection at Typical Temperature and Humidity Ranges The CO Alarm is not formulated to detect CO levels below 30 ppm typically UL tested for false alarm resistance to Methane 500 ppm Butane 300 ppm Heptane 500 ppm Ethyl Acetate 200 ppm Isopropyl Alcohol 200 ppm and Carbon Dioxide 5000 ppm Values measure gas and vapor concentrations in parts per million Audible Alarm 85 dB minimum at 10 feet 3 meters REGULATORY INFORMATI
21. alarm levels of smoke or carbon monoxide The Latching Alarm Indicator stays ON until you clear it so it can alert you to an alarm that occurred while you were away from home even though smoke or CO present in the air has dropped below alarm levels Low Battery Latch is activated when the Alarm is in the low battery condition When this occurs the Smoke Power LED flashes Green On for 2 seconds Off for 2 seconds This feature is designed to help you identify which Alarm needs to have the battery replaced Although the Alarm will sound the low battery chirp approximately once every minute sometimes during the initial stages of low battery the Alarm will chirp in greater intervals than one minute sometimes up to several hours until the battery reaches a steady low battery level This innovative feature eliminates the frustration of waiting for and or identifying which unit is chirping SMART INTERCONNECT FEATURE This Alarm includes Smart Interconnect which enables the Alarm to be interconnected with other First Alert and BRK Smoke Heat and Smart Interconnect CO Alarms When smoke is detected all Alarms will sound the smoke horn pattern When CO is detected Smart Interconnect Alarms will sound the CO horn pattern Alarms that do not have the Smart Interconnect feature will remain silent during a CO alarm WHAT YOU NEED TO KNOW ABOUT CO WHAT IS CO CO is an invisible odorless tasteless gas produced when fossil fu
22. ancy approved single and multiple station Smoke Alarms shall be installed as follows 1 In all sleeping rooms Exception Smoke Alarms shall not be required in sleeping rooms in existing one and two family dwelling units 2 Outside of each separate sleeping area in immediate vicinity of the sleeping rooms 3 On each level of the dwelling unit including basements Exception In existing one and two family dwelling units approved Smoke Alarms powered by batteries are permitted A 11 8 3 Are More Smoke Alarms Desirable The required number of Smoke Alarms might not provide reliable early warning protection for those areas separated by a door from the areas protected by the required Smoke Alarms For this reason it is recom mended that the householder consider the use of additional Smoke Alarms for those areas for increased protection The additional areas include the basement bedrooms dining room furnace room utility room and hallways not protected by the required Smoke Alarms The installation of Smoke Alarms in kitchens unfinished attics or garages is not normally recommended as these locations occasionally experience conditions that can result in improper operation California State Fire Marshal CSFM Early warning detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows A Smoke Alarm installed in each separate sleeping area in the vicinity b
23. ared wall e Keep windows and doors open slightly If you suspect that CO is escaping into your home open a window or a door Opening windows and doors can significantly decrease CO levels In addition familiarize yourself with all enclosed materials Read this manual in its entirety and make sure you understand what to do if your CO Alarm sounds REGULATORY INFORMATION FOR SMOKE CO ALARMS REGULATORY INFORMATION FOR CO ALARMS WHAT LEVELS OF CO CAUSE AN ALARM Underwriters Laboratories Inc Standard UL2034 requires residential CO Alarms to sound when exposed to levels of CO and exposure times as described below They are measured in parts per million ppm of CO over time in minutes UL2034 Required Alarm Points e lf the alarm is exposed to 400 ppm of CO IT MUST ALARM BETWEEN 4 and 15 MINUTES e lf the alarm is exposed to 150 ppm of CO IT MUST ALARM BETWEEN 10 and 50 MINUTES e lf the alarm is exposed to 70 ppm of CO IT MUST ALARM BETWEEN 60 and 240 MINUTES Approximately 10 COHb exposure at levels of 10 to 95 Relative Humidity RH The unit is designed not to alarm when exposed to a constant level of 30 ppm for 30 days IMPORTANT CO Alarms are designed to alarm before there is an immediate life threat Since you cannot see or smell CO never assume it s not present e An exposure to 100 ppm of CO for 20 minutes may not affect average healthy adults but after 4 hours the same level may cause head
24. e basic installation of this Alarm is similar whether you want to install one Alarm or interconnect more than one Alarm If you are interconnecting more than one Alarm you MUST read Special Requirements For Interconnected Alarms below before you begin installation ADANGER ELECTRICAL SHOCK HAZARD Turn off power to the area where you will install this unit at the circuit breaker or fuse box before beginning installation Failure to turn off the power before installa tion may result in serious electrical shock injury or death 1 Remove the mounting bracket from the base and attach it to the junction box 2 Using wire nuts connect the power connector to the household wiring STAND ALONE ALARM ONLY Connect the white wire on the power connector to the neutral wire in the junction box Connect the black wire on the power connector to the hot wire in the junction box Tuck the orange wire inside the junction box It is used for interconnect only INTERCONNECTED UNITS ONLY Strip off about 1 2 12 mm of the plastic coating on the orange wire on the power connector Connect the white wire on the power connector to the neutral wire in the junction box Connect the black wire on the power connector to the hot wire in the junction box Connect the orange wire on the power connector to the interconnect wire in the junction box Repeat for each unit you are interconnecting Never connect the hot or neutral
25. e or circuit breaker must power all interconnected units e The total length of wire interconnecting the units should be less than 1000 feet 300 meters This type of wire is commonly available at Hardware and Electrical Supply stores e All wiring must conform to all local electrical codes and NFPA 70 NEC Refer to NFPA 72 NFPA 101 and or your local building code for further connection requirements A Unswitched 120VAC B To additional units Maximum 18 total 60 Hz source Maximum 12 Smoke Alarms 1 Alarm 4 Wire Nut 2 Ceiling or Wall 5 Junction Box 3 Power Connector 6 Neutral Wire Wht 7 Interconnect Wire Orange 8 Hot Wire Blk STEP BY STEP GUIDE TO PROGRAMMING THIS ALARM For First Time and When Changing Batteries Action Alarm Will Say 1 Insert batteries 2 AA batteries Welcome First Alert Carbon Monoxide and Smoke Alarm No location programmed if first time or Location example Basement location programmed when changing batteries To select location press and hold test button now 2 Press amp Hold Test Button if To save location press and hold you would like to program the test button after location is location or change the location heard Alarm will speak list of of the Alarm Release button locations see below after Alarm responds 3 After you hear the location of Location
26. ea in the immediate vicinity of the bedrooms For added protection install additional CO Alarms in each separate bedroom and on every level of your home NOTE For added protection install an additional Smoke CO Alarm at least 15 feet 4 6 meters away from the furnace or fuel burning heat source where possible In smaller homes or in manufactured homes where this distance cannot be maintained install the Alarm as far away as possible from the furnace or other fuel burning source Installing the Alarm closer than 15 feet 4 6 meters will not harm the Alarm but may increase the frequency of unwanted alarms In general install combination Smoke and Carbon Monoxide Alarms e Onevery level of your home including finished attics and basements e Inside every bedroom especially if people sleep with the door partly or completely closed e Inthe hall near every sleeping area If your home has multiple sleeping areas install a unit in each If a hall is more than 40 feet 12 meters long install a unit at each end e At the top of first to second floor stairs e At the bottom of the basement stairs e For additional coverage install Alarms in all rooms halls and storage areas where temperatures normally remain between 40 F and 100 F 4 C and 38 C RECOMMENDED PLACEMENT SUGGESTED AREAS FOR INSTALLING SMOKE ALARMS CO ALARMS AND COMBO UNITS TE oo BASEMENT KEY smoke alarms VAN SMOKE ALARM WITH SIL
27. els do not burn completely or are exposed to heat usually fire Electrical appliances typically do not produce CO These fuels include Wood coal charcoal oil natural gas gasoline kerosene and propane Common appliances are often sources of CO If they are not properly maintained are improperly ventilated or malfunction CO levels can rise quickly CO is a real danger now that homes are more energy efficient Air tight homes with added insulation sealed windows and other weatherproofing can trap CO inside SYMPTOMS OF CO POISONING These symptoms are related to CO POISONING and should be discussed with ALL household members Mild Exposure Slight headache nausea vomiting fatigue flu like symptoms Medium Exposure Throbbing headache drowsiness confusion fast heart rate Extreme Exposure Convulsions unconsciousness heart and lung failure Exposure to Carbon Monoxide can cause brain damage death IMPORTANT This CO Alarm measures exposure to CO over time It alarms if CO levels are extremely high in a short period of time or if CO levels reach a certain minimum over a long period of time The CO Alarm generally sounds an alarm before the onset of symptoms in average healthy adults Why is this important Because you need to be warned of a potential CO problem while you can still react in time In many reported cases of CO exposure victims may be aware that they are not feeling well but bec
28. er than 40 F C or hotter than 100 F 88 C These areas include non airconditioned crawl spaces unfinished attics uninsulated or poorly insulated ceilings porches and garages e In insect infested areas Insects can clog the openings to the sensing chamber e Less than 12 inches 305 mm away from fluorescent lights Electrical noise can interfere with the sensor e In dead air spaces See Avoiding Dead Air Spaces AVOIDING DEAD AIR SPACES Dead air spaces may prevent smoke from reaching the Smoke CO Alarm To avoid dead air spaces follow installation recommendations below On ceilings install Smoke CO Alarms as close to the center of the ceiling as possible If this is not possible install the Smoke CO Alarm at least 4 inches 102 mm from the wall or corner For wall mounting if allowed by building codes the top edge of Smoke CO Alarms should be placed between 4 inches 102 mm and 12 inches 305 mm from the wall ceiling line below typical dead air spaces On a peaked gabled or cathedral ceiling install first Smoke CO Alarm within 3 feet 0 9 meters of the peak of the ceiling measured horizontally Additional Smoke CO Alarms may be required depending on the length angle etc of the ceiling s slope Refer to NFPA 72 for details on requirements for sloped or peaked ceilings HOW TO INSTALL THIS SMOKE CO ALARM This Smoke CO Alarm is designed to be mounted on any standard wi
29. es furnace rooms crawl spaces and unfinished attics Avoid extremely dusty dirty or greasy areas e Where combustion particles are produced Combustion particles form when something burns Areas to avoid include poorly ventilated kitchens garages and furnace rooms Keep units at least 20 feet 6 meters from the sources of combustion particles stove furnace water heater space heater if possible In areas where a 20 foot 6 meter distance is not possible in modular mobile or smaller homes for example it is recommended the Smoke Alarm be placed as far from these fuel burning sources as possible The placement recommendations are intended to keep these Alarms at a reasonable distance from a fuel burning source and thus reduce unwanted alarms Unwanted alarms can occur if a Smoke Alarm is placed directly next to a fuel burning source Ventilate these areas as much as possible e Within 5 feet 1 5 meters of any cooking appliance In air streams near kitchens Air currents can draw cooking smoke into the smoke sensor and cause unwanted alarms e In extremely humid areas This Alarm should be at least 10 feet 3 meters from a shower sauna humidifier vaporizer dishwasher laundry room utility room or other source of high humidity e In direct sunlight e In turbulent air like near ceiling fans or open windows Blowing air may prevent CO or smoke from reaching the sensors e In areas where temperature is cold
30. example Basement where you are placing the Alarm location saved No location saved Your Alarm has now been programmed for the location of your choice Available locations Basement Kitchen Living Room Dining Room Child s Bedroom Master Bedroom Family Room No Location Guest Bedroom Office Hallway Utility Room 4 LOCKING FEATURES The locking features are designed to discourage unauthorized removal of the batteries or Alarm It is not necessary to activate the locks in single family households where unauthorized battery or Alarm removal is not a concern These Alarms have two separate locking features one to lock the battery compartment and the other to lock the Alarm to the mounting bracket You can choose to use either feature independently or use them both Tools you will need Needle nose pliers Standard Flathead screwdriver Both locking features use locking pins which are molded into the mounting bracket Using needle nose pliers remove one or both pins from the mounting bracket depending on how many locking features you want to use IMPORTANT To permanently remove either lock insert a flathead screwdriver between the locking pin and the lock and pry the pin out of the lock TO LOCK THE BATTERY COMPARTMENT Do not lock the battery compartment until you have installed the battery and tested the battery back up TO UNLOCK THE BATTERY COMPARTMENT IMPORTANT Once the Alarm is installed
31. hen it returns to normal operation Never remove the batteries from a battery operated unit to stop an unwanted alarm caused by cooking smoke etc Instead open a window or fan the smoke away from the unit The alarm will reset automatically A CAUTION e Connect this unit ONLY to other compatible units See How To Install This Smoke Alarm for details Do not connect it to any other type of alarm or auxiliary device Connecting anything else to this unit may damage it or prevent it from operating properly This Smoke CO Alarm has a battery drawer which resists closing unless a battery is installed This warns you the unit will not operate under DC power without a battery Do not stand too close to the unit when the alarm is sounding It is loud to wake you in an emergency Exposure to the horn at close range may harm your hearing Do not paint over the unit Paint may clog the openings to the sensing chambers and prevent the unit from operating properly INSTALLATION WHERE TO INSTALL THIS ALARM Minimum coverage for Smoke Alarms as recommended by the National Fire Protection Association NFPA is one Smoke Alarm on every floor in every sleeping area and in every bedroom See Regulatory Information For Smoke Alarms for details on the NFPA recommendations For CO Alarms the National Fire Protection Association NFPA recommends that a CO Alarm should be centrally located outside of each separate sleeping ar
32. ing HVAC equipment combustion appliances and equipment and or gas fireplaces or other decorative combustion equipment AFTER AN ALARM After the emergency responders arrive the premises aired out and your CO Alarm remains in its normal condition you can check what the highest carbon monoxide level sensed was Action Alarm Will Say 1 Press amp Hold Test Button Highest carbon monoxide level was ___ ppm Please see manual To clear highest carbon monoxide level press and hold test button now 2 Press amp Hold Test Button if Highest carbon monoxide level you would like to clear the cleared highest level sensed If you would like to keep the highest level in memory do not press anything Alarm will say nothing IF THE SMOKE ALARM SOUNDS RESPONDING TO AN ALARM AWARNING e If the unit alarms and you are not testing the unit it is warning you of a potentially dangerous situation that requires your immediate attention NEVER ignore any alarm Ignoring the alarm may result in injury or death e Never remove the batteries from a battery operated Smoke CO Alarm to stop an unwanted alarm caused by cooking smoke etc Removing batteries disables the alarm so it cannot sense smoke and removes your protection Instead open a window or fan the smoke away from the unit The alarm will reset automatically e If the unit alarms get everyone out of the house immediately WHAT TO DO IN CASE OF FIRE
33. ion It monitors the air and sounds a loud alarm before Carbon Monoxide levels become threatening for average healthy adults A CO Alarm is not a substitute for proper maintenance of home appliances To help prevent CO problems and reduce the risk of CO poisoning e Clean chimneys and flues yearly Keep them free of debris leaves and nests for proper air flow Also have a professional check for rust and corrosion cracks or separations These conditions can prevent proper air movement and cause backdrafting Never cap or cover a chimney in any way that would block air flow e Test and maintain all fuel burning equipment annually Many local gas or oil companies and HVAC companies offer appliance inspections for a nominal fee e Make regular visual inspections of all fuel burning appliances Check appliances for excessive rust and scaling Also check the flame on the burner and pilot lights The flame should be blue A yellow flame means fuel is not being burned completely and CO may be present Keep the blower door on the furnace closed Use vents or fans when they are available on all fuel burning appliances Make sure appliances are vented to the outside Do not grill or barbecue indoors or in garages or on screen porches e Check for exhaust backflow from CO sources Check the draft hood on an operating furnace for a backdraft Look for cracks on furnace heat exchangers e Check the house or garage on the other side of sh
34. ion alarm needs to be replaced Improved UV Resistance keeps the alarm from discoloring over time 2010 BRK Brands Inc All rights reserved Distributed by BRK Brands Inc 3901 Liberty Street Road Aurora IL 60504 8122 Consumer Affairs 800 323 9005 e www firstalert com All First Alert Smoke Alarms conform to regulatory requirements including UL217 and are designed to detect particles of combustion Smoke particles of varying number and size are produced in all fires x Ionization technology is generally more sensitive than photoelectric D technology at detecting small particles which tend to be produced in greater amounts by flaming fires which consume combustible materials rapidly and spread quickly Sources of these fires may include paper burning in a wastebasket or a grease fire in the kitchen Photoelectric technology is generally more sensitive than ionization p technology at detecting large particles which tend to be produced in greater amounts by smoldering fires which may smolder for hours before bursting into flame Sources of these fires may include cigarettes burning in couches or bedding For maximum protection use both types of Smoke Alarms on each level and in every bedroom of your home ADANGER ELECTRICAL SHOCK HAZARD Turn off the power to the area where the Smoke Alarm is installed before removing it from the mounting bracket Failure to turn off the power first may result in serious elec
35. le Keep the original sales receipt Proof of purchase is required to obtain warranty performance BRK dealers service centers or retail stores selling BRK products do not have the right to alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions disassembly repair or alteration by anyone other than BRK or an authorized service center Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes or any batteries that are included with this unit For your records please record Date Purchased Date Installed Month Year Replace alarm 7 years after installation Please write the date in the space provided Month Year The alarm will also provide an audible End of Life Signal approximately 7 years after installation to remind you to replace the unit The End of Life Signal can be silenced for up to 2 days Do not unplug the alarm or remove the batteries until you get replacement 11 BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the
36. nd receive signals AC powered Alarms will not operate Interconnected units can provide earlier warning of fire than stand alone units especially if a fire starts in a remote area of the dwelling If any unit in the series senses smoke all units will alarm To determine which Alarm initiated an alarm see table During an Alarm On Initiating Alarm s Red LED s flashes flash rapidly On All Other Alarms Red LED is Off After an Alarm Latching On Initiating Alarm s Red LED s On for 2 seconds Off for 2 seconds On All Other Alarms Green LED s On Red LED s Off Compatible Interconnected Units IMPORTANT Interconnect units within a single family residence only Otherwise all households will experience unwanted alarms when you test any unit in the series Interconnected units will only work if they are wired to compatible units and all requirements are met This unit is designed to be compatible with BRK Electronics Smoke Alarm Models 9120 9120B SC9120B 7010 7010B 4120 4120B 4120SB 4919 2002RAC 100S 5919 5919TH BRK Electronics Heat Alarm Models HD6135F HD6135FB BRK Electronics CO Alarm Models CO5120BN CO5120PDBN Smoke CO Alarm Model SC6120B SC7010BV SC7010B and First Alert Smoke Alarm Models SA4120 SA4120B SA4121B SA4919B SA100B Interconnected units must meet ALL of the following requirements e A maximum of 18 compatible units may be interconnected Maximum of 12 Smoke Alarms e The same fus
37. ny local retail stores IMPORTANT Actual battery service life depends on the Alarm and the environment in which it is installed All the batteries specified above are acceptable replacement batteries for this unit Regardless of the manufacturer s suggested battery life you MUST replace the battery immediately once the unit starts chirping the low battery warning To replace the batteries without removing Alarm from the ceiling or wall 1 Open the battery compartment 2 Press tabs A and B as shown in the diagram and remove each battery 3 Insert the new batteries making sure they snap completely into the battery compartment Match the terminals on the ends of the batteries with the terminals on the unit 4 Close the battery compartment and then test the unit by pressing the Test Silence button IF YOUR SMOKE CO ALARM SOUNDS WHAT TO DO FIRST IDENTIFY THE TYPE OF ALARM SIGNAL Refer to previous section What you will see and hear with this alarm IF THE CO ALARM SOUNDS ALARM MOVE TO FRESH AIR If you hear the CO alarm horn and the CO red light is flashing move everyone to a source of fresh air DO NOT remove the batteries AWARNING Actuation of your CO Alarm indicates the presence of carbon monoxide CO which can kill you In other words when your CO Alarm sounds you must not ignore it IF THE CO ALARM SIGNAL SOUNDS 1 Operate the Test Silence button 2 Call your eme
38. of Smoke CO Alarms you must press the Test Silence button on the initiating alarm The unit with the flashing red light the red light will be off on all other Alarms If you press the Test Silence on any other Alarm it will only silence that unit not the whole interconnected series 7 SILENCING THE END OF LIFE SIGNAL This silence feature can temporarily quiet the End of Life warning chirp for up to 2 days You can silence the End of Life warning chirp by pressing the Test Silence button The horn will chirp acknowledging that the End of Life silence feature has been activated After approximately 2 days the End of Life chirp will resume After approximately 2 3 weeks the End of Life warning cannot be silenced LATCHING FEATURES Alarm Latch is activated after an Alarm is exposed to alarm levels of smoke or carbon monoxide This feature will only work with AC power After smoke or CO levels drop below alarm levels the Smoke Power or CO Red LED will begin to flash once every few seconds It will continue to flash or latch until you clear it by testing the alarm This feature helps emergency responders investigators or service technicians identify which unit s in your home were exposed to alarm levels of smoke or carbon monoxide This can help investigators pinpoint the source of smoke or CO Interconnected Alarms Latching Alarm Indicator shows which Alarm s in the series were exposed to
39. ome disoriented and can no longer react well enough to exit the building or get help Also young children and pets may be the first affected The average healthy adult might not feel any symptoms when the CO Alarm sounds However people with cardiac or respiratory problems infants unborn babies pregnant mothers or elderly people can be more quickly and severely affected by CO If you experience even mild symptoms of CO poisoning consult your doctor immediately FINDING THE SOURCE OF CO AFTER AN ALARM Carbon monoxide is an odorless invisible gas which often makes it difficult to locate the source of CO after an alarm These are a few of the factors that can make it difficult to locate sources of CO e House well ventilated before the investigator arrives e Problem caused by backdrafting e Transient CO problem caused by special circumstances Because CO may dissipate by the time an investigator arrives it may be difficult to locate the source of CO BRK Brands Inc shall not be obligated to pay for any carbon monoxide investigation or service call POTENTIAL SOURCES OF CO IN THE HOME Fuel burning appliances like portable heater gas or wood burning fireplace gas kitchen range or cooktop gas clothes dryer Damaged or insufficient venting corroded or disconnected water heater vent pipe leaking chimney pipe or flue or cracked heat exchanger blocked or clogged chimney opening Improper use of appliance device ope
40. onoxide in Location example Basement Evacuate Pause Highest carbon monoxide level was CO level example __ ppm Horn 4 beeps pause 4 beeps pause repeating 2 times followed by Voice Warning above Power Smoke LED Off CO LED During Alarm Flashes Red in sync with the horn pattern After Alarm Flashes Red On for 2 seconds Off for 2 seconds CO Alarm Latch is now engaged NOTE If unit goes into CO alarm the regular 4 beeps brief pause cycle will repeat for fifteen minutes After fifteen minutes the pause will increase to one minute Smoke is Detected Horn 3 beeps pause repeating 8 times Voice Warning evacuate smoke in Location example Basement Evacuate Horn Sia pause repeating 3 times followed by Voice Warning above Power Smoke LED During Alarm Flashes Red in sync with the horn pattern After Alarm Flashes Red On for 2 seconds Off for 2 seconds Smoke Alarm Latch is now engaged CO LED Off CO Alarm is Silenced Voice Horn silenced Detector active Smoke Alarm is Silenced Voice Horn silenced Detector active Horn Off Horn Off Power Smoke LED Power Smoke LED Off rae eone CO LED Flashes Red CO LED Off 2 Pry the Alarm away from the bracket by mounting bracket pin and the mounting bracket turning both the screwdriver and the Alarm counterclockwise left at the same time REGULAR MAINTENANCE AWARNING Use only the repl
41. rating a barbecue grill or vehicle in an enclosed area like a garage or screened porch Transient CO Problems transient or on again off again CO problems can be caused by outdoor conditions and other special circumstances The following conditions can result in transient CO situations 1 Excessive spillage or reverse venting of fuel appliances caused by outdoor conditions such as e Wind direction and or velocity including high gusty winds Heavy air in the vent pipes cold humid air with extended periods between cycles e Negative pressure differential resulting from the use of exhaust fans e Several appliances running at the same time competing for limited fresh air e Vent pipe connections vibrating loose from clothes dryers furnaces or water heaters e Obstructions in or unconventional vent pipe designs which can amplify the above situations 2 Extended operation of unvented fuel burning devices range oven fireplace 3 Temperature inversions which can trap exhaust close to the ground 4 Car idling in an open or closed attached garage or near a home These conditions are dangerous because they can trap exhaust in your home Since these conditions can come and go they are also hard to recreate during a CO investigation MULTI STORY RESIDENCE 1 STORY RESIDENCE BEDROOM oe BEDROOM F wy L E HOW CAN I PROTECT MY FAMILY FROM CO POISONING A CO Alarm is an excellent means of protect
42. rer for replacement See Limited Warranty for details Immediately replace the Alarm IF YOU ARE FEELING SYMPTOMS OF CO POISONING EVACUATE your home and call 911 or the Fire Department Refer to If The CO Alarm Sounds for details Relocate your Alarm If frequent alarms continue have home rechecked for potential CO problems You may be experiencing an intermittent CO problem Silence Alarm using manual button clean the Alarm s cover with a soft clean cloth If frequent unwanted alarms continue relocate your Alarm Alarm may be too close to a kitchen cooking appliance or steamy bathroom If you have questions that cannot be answered by reading this manual call Consumer Affairs at 1 800 323 9005 M F 7 30 a m to 5 00 p m CST LIMITED WARRANTY BRK Brands Inc BRK the maker of First Alert brand products warrants that for a period of seven years from the date of purchase this product will be free from defects in material and workmanship BRK at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferab
43. rgency services fire department or 911 Write down the number of your local emergency service here 3 Immediately move to fresh air outdoors or by an open door or window Do a head count to check that all persons are accounted for Do not re enter the premises or move away from the open door or window until the emergency services responder has arrived the premises have been aired out and your CO Alarm remains in its normal condition 4 After following steps 1 3 if your CO Alarm reactivates within a 24 hour period repeat steps 1 3 and call a qualified appliance technician to investigate for sources of CO from fuel burning equipment and appliances and inspect for proper operation of this equipment If problems are identified during this inspection have the equipment serviced immediately Note any combustion equipment not inspected by the technician and consult the manufacturers instructions or contact the manufacturers directly for more information about CO safety and this equipment Make sure that motor vehicles are not and have not been operating in an attached garage or adjacent to the residence Write down the number of a qualified appliance technician here NOTE A qualified appliance technician is defined as a person firm corporation or company that either in person or through a representative is engaged in and responsible for the installation testing servicing or replacement of heating ventilation air condition
44. ring junction box up to a 4 inch 10 cm size on either the ceiling or wall if allowed by local codes Read Where to Install This Alarm and Where This Alarm Should Not Be Installed before you begin installation Tools you will need e Needle nose pliers or utility knife Standard flathead screwdriver Wire strippers AWARNING Make sure the Alarm is not receiving excessively noisy power Examples of noisy power could be major appliances on the same circuit power from a generator or solar power light dimmer on the same circuit or mounted near fluorescent lighting Excessively noisy power may cause damage to your Alarm THE PARTS OF THIS ALARM The Mounting Bracket To remove the mounting bracket from the Alarm base hold the Alarm base firmly and twist the mounting bracket counterclockwise The mounting bracket installs onto the junction box It has a variety of screw slots to fit most boxes Y The Power Connector The power connector plugs into a power input block on the Alarm It supplies the unit with AC power e The black wire is hot e The white wire is neutral e The orange wire is used for interconnect If you need to remove the power connector turn POWER OFF first Insert a flat screwdriver blade between the power connector and the security tab inside the power input block Gently pry back the tab and pull the connector free FOLLOW THESE INSTALLATION STEPS Th
45. t 1 Push and hold Test Silence button until the alarm sounds IMPORTANT If the unit does not alarm during testing DO NOT lock the battery compartment Install a new battery and test again If the Alarm still does not alarm replace it immediately 3 Push the locking pin through the hole near the battery drawer on the back of the Alarm TO LOCK THE MOUNTING BRACKET 1 Using needle nose pliers detach one locking pin from mounting bracket TO UNLOCK THE MOUNTING BRACKET ADANGER ELECTRICAL SHOCK HAZARD Turn off the power to the area where the Alarm is installed before removing it from the mounting bracket Failure to turn off the power first may result in serious electrical shock injury or death AWARNING Always discharge the branch circuit before servicing an AC or AC DC Alarm First turn off the AC power at the circuit breaker or fuse box Next remove the battery from Alarms with battery back up Finally press and hold the Test Silence button for 5 10 seconds to discharge the branch circuit 2 Insert the locking pin into the lock located opposite from the battery drawer as shown in the diagram 1 Insert a flathead screwdriver between the 3 When you attach the Alarm to the mounting bracket the locking pin s head will fit into a notch on the bracket WHAT YOU WILL SEE AND HEAR WITH THIS ALARM Under Normal Operations Voice Silent Horn Silent Power Smoke LED
46. trical shock injury or death AWARNING e This unit will not alert hearing impaired residents It is recommended that you install special units which use devices like flashing strobe lights to alert hearing impaired residents Installation of this unit must conform to the electrical codes in your area Articles 210 and 300 3 B of NFPA 70 NEC NFPA 72 NFPA 101 SBC SBCCI UBC ICBO NBC BOCA OTFDC CABO and any other local or building codes that may apply Wiring and installation must be performed by a licensed electrician Failure to follow these guidelines may result in injury or property damage This unit must be powered by a 24 hour 120VAC pure sine wave 60Hz circuit Be sure the circuit cannot be turned off by a switch dimmer or ground fault circuit interrupter Failure to connect this unit to a 24 hour circuit may prevent it from providing constant protection This Alarm must have AC or battery power to operate If the AC power fails battery back up will allow the alarm to sound for at least 4 minutes If AC power fails and the battery is weak protection should last for at least 7 days If AC power fails and the battery is dead or missing the alarm cannot operate Never disconnect the power from an AC powered unit to stop an unwanted alarm Doing so will disable the unit and remove your protection In the case of a true unwanted alarm open a window or fan the smoke away from the unit The alarm will reset automatically w
47. ttery or AC power install both types of units This Smoke CO Alarm will not sense smoke or CO that does not reach the sensors It will only sense smoke or CO at the sensor Smoke or CO may be present in other areas Doors or other obstructions may affect the rate at which CO or smoke reaches the sensors If bedroom doors are usually closed at night we recommend you install an alarm device Combination CO and Smoke Alarm or separate CO Alarms and Smoke Alarms in each bedroom and in the hallway between them This Smoke CO Alarm may not sense smoke or CO on another level of the home Example This alarm device installed on the second floor may not sense smoke or CO in the basement For this reason one alarm device may not give adequate early warning Recommended minimum protection is one alarm device in every sleeping area every bedroom and on every level of your home Some experts recommend battery powered Smoke and CO Alarms be used in conjunction with interconnected AC powered Smoke Alarms For details see About Smoke Alarms for details Smoke CO Alarms may not be heard The alarm horn loudness meets or exceeds current UL standards of 85 dB at 10 feet 3 meters However if the Smoke CO Alarm is installed outside the bedroom it may not wake up a sound sleeper or one who has recently used drugs or has been drinking alcoholic beverages This is especially true if the door is closed or only partly open Even persons who are awake
48. ugh the 2200 3400 Hz range Smart Interconnect can be interconnected to BRK Smoke CO and Heat Alarms One interconnect wire carries both smoke and CO alarm signals Optipath 360 Technology provides 360 degrees of direct access to the smoke sensor Single Button Test Silence eliminates confusion Depending on what mode the alarm is in pushing the button provides different functions such as testing the alarm silencing the alarm re testing the alarm when in silence and clearing the Latching features Two Silence Features Temporarily silence low battery chirp for up to eight hours before replacing low battery or silence an unwanted alarm for several minutes Two Latching Features Alarm Latch Easily identifies initiating alarm even after alarm condition has subsided Low Battery Latch Identifies which unit is in low battery condition Perfect Mount System includes a gasketless base for easy installation and a mounting bracket that keeps the alarm secure over a wide rotation range to allow for perfect alignment Dust Cover is included to keep the alarm clean during construction Easy Installation Maintenance features include a large opening in the mounting bracket for easy access to wiring A battery pull tab that keeps the battery fresh until the home is occupied A Side Load Battery Drawer allows for easy battery replacement without removing the alarm from the ceiling or wall End of Life Signal Provides audible confirmat
49. uide as c scsunncaeeeniw ese ticeonees cau 11 12 Limited Warranty 442 4 22sscscceteesicctetenncdewneneed 11 12 First Alert is a registered trademark of the First Alert Trust Printed in Mexico M08 0183 006 K1 09 10 12
50. ulations 3 Institutions Hospitals day care facilities long term health care facilities This unit is suitable for use in individual patient sleeping resident rooms provided a primary fire detection system already exists to meet fire detection requirements in common areas like lobbies hallways or porches Using this unit in common areas may not provide sufficient warning to all residents or meet local fire protection ordinances regulations 4 Hotels and Motels Also boarding houses and dormitories This unit is suitable for use inside individual sleeping resident rooms provided a primary fire detection system already exists to meet fire detection requirements in common areas like lobbies hallways or porches Using this unit in common areas may not provide sufficient warning to all residents or meet local fire protection ordinances regulations 5 Warehouses Commercial Buildings DO NOT use this Smoke CO Alarm in warehouses industrial or commercial buildings special purpose non residential buildings RVs boats or airplanes This Smoke CO Alarm is specifically designed for residential use and may not provide adequate protection in non residential applications 10 GENERAL LIMITATIONS OF SMOKE CO ALARMS This Smoke CO Alarm is intended for residential use It is not intended for use in industrial applications where Occupational Safety and Health Administration OSHA requirements for Carbon Monoxide Alarms must be met The
51. ut outside bedrooms and Heat or Smoke Alarms in the living rooms dining rooms bedrooms kitchens hallways finished attics furnace rooms closets utility and storage rooms basements and attached garages ABOUT SMOKE ALARMS Battery DC operated Smoke Alarms Provide protection even when electricity fails provided the batteries are fresh and correctly installed Units are easy to install and do not require professional installation However they do not provide interconnected functionality AC powered Smoke Alarms Can be interconnected so if one unit senses smoke all units alarm They do not operate if electricity fails AC with battery DC back up will operate if electricity fails provided the batteries are fresh and correctly installed AC and AC DC units must be installed by a qualified electrician Wireless Interconnected Alarms Offer the same interconnected functionality as with hardwired alarms without wires Units are easy to install and do not require professional installation They provide protection even when electricity fails provided the batteries are fresh and correctly installed Smoke CO Alarms for Solar or Wind Energy users and battery backup power systems AC powered Smoke CO Alarms should only be operated with true or pure sine wave inverters Operating this Alarm with most battery powered UPS uninterruptible power supply products or square wave or quasi sine wave inverters will damage the Alarm If
Download Pdf Manuals
Related Search