Home

Broadband Module/ Broadband Module Plus

1. gt 10BASETWAN ASDL LAN PORT 1 LAN PORT 2 th Hh LAN PORT3 LAN PORT 4 ul u Heartbeat steady to indicate normal processor activity ADSL a solid light indicates ADSL line synchronisation flashes with activity LAN 1 a solid light indicates an Ethernet connection flashes with activity LAN 2 a solid light indicates an Ethernet connection flashes with activity LAN 3 a solid light indicates an Ethernet connection flashes with activity LAN 4 a solid light indicates an Ethernet connection flashes with activity An additional two indicators LEDs on the MDF indicate e Not used permanently lit e WAN ETH DMZ a solid light indicates an Ethernet connection BT Versatility Broadband Module Broadband Module Plus Manual RESET BUTTON The MDF is equipped with a white reset button When this button is pressed the moduleresets LOCAL AREA NETWORK The module is equipped with a 4 port LAN with the following characteristics 10 100 Mb s switched Ethernet Mode The LAN device can operate in FDX Full Duplex or HDX Half Duplex mode MDI MDI X The port will automatically detect whether a straight or crossover cable is used to connect the LAN device and will adjust itself accordingly Autosensing The port will automatically adapt to the speed and mode of the device that is connected to it Connectors RJ 45 WIDE AREA NETWORK PORTS The
2. ti a v 1 c n D ct 2 in io io io ih ia ic Hen im iO ic io io S i ip io IES io i iui itu ict im iz im ini i5 im ig iz itn reete reete ertterneseesee Cancel Broadband Module ADSL Modem Manual Setup For manually configured Internet Access you must provide values for the fields below Your Internet Service Provider should provide these values 3 Tell me more about manual Internet Access settings Broadband Module WAN address 213 84 222 17 Broadband Module WAN Subnet Mask 255 255 255 0 Internet Gateway address 213 94 1222 176 Primary DNS address 212 1 32 a Secondary DNS address 212 17 232 Jal Cancel e Enter the required IP addresses and Subnet mask e Select Next The following screen is displayed Broadband Module Basic Configuration Status System Backup Restore L3 System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAM Broadband Module ADSL Modem RFC1483 Mode There are four types of RFC1483 connection available Choose a type that is suitable for your Internet connection from the options below 8 Tell me more about ADSL Modem settings LLC Bridged C LLC Routed C wCMux Bridged C wCMux Routed Enable Link State Monitoring M Next gt Cancel e Select one
3. System Backup Restore 3 Tell me more about VoIP Sia nra Username Password Advanced Configuration IP Trunk 1 23456789 eecscese Restart Required IP Trunk 2 34567890 eecesces An implement your Endpoint 3 changes a restart is required Endpoint 4 C Endpoint 5 EE El Reser tione i EEEREN con i EEEEENS etup TUM Endpoint 8 NENNEN NENNEN ADSL Modem Endpoint 9 ld LE PONE Endpoint 10 8 EHE o a endpoint 11 i REIHEN wan Endpoint 12 MENEENE NEEHEENE Cancel Enter the Username and Password for each trunk Select Next Status TOT Ue ET BB LL eT DH 0TS VoIP Confirm The endpoint settings will be System Backup Restore System Restart Username MAC Advanced Configuration IP Trunk 1 23456789 IP Trunk 2 34567890 Restart Required Endpoint 3 Not Configured To implement your Endpoint 4 Not Configured changes a restart is Endpoint 5 Not Configured required Endpoint 6 Not Configured Endpoint 7 Not Configured Restart Endpoint 8 Not Configured Endpoint 9 Not Configured Setup Endpoint 10 Not Configured LAN Gateway Endpoint 11 Not Configured ADSL Modem Endpoint 12 Not Configured ETH DMZ Port VoIP ISDN WLAN To confirm this setting click on the Confirm Changes button below If r oO r a a a m ui ui you do not wish to apply this setting click on the Cancel button Confirm Changes Cancel BT Versatility Broadb
4. 3roadband Module prasdbaind Fiedule NAT Add Global Address Pool ipwan Basic Configuration Advanced Configuration ADSL Test Add Global Address Pool Subnet Mask IP Address 2 Interface Use Subnet Type Configuration internal Use Subnet Mask Reset to Defaults IP Address Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server fidvancead TANM Add Global Address Pool e Select an interface from the drop down list e Enter an IP address and subnet mask or enter the first and last IP addresses in the range e Select Add Global Address Pool Reserved Mappings Reserved mappings are used to create exceptions to the normal NAT rules to allow incoming access to a specific server or application on the DMZ or LAN A static route is defined between an external IP address and internal IP addresses Reserved mapping is also called Port address Translation or Port Forwarding e Select Advanced NAT Configuration Advanced Setup Admin Accounts Rese rved Ma ppings Firewall amp Security IP Routes No Reserved Mappings DHCP Server Advanced ISDN Add Reserved Mapping e Select Add Reserved Mapping The following screen is displayed NAT Add Reserved Mapping ipwan Add Reserved Mapping IP Addresses Transport External Port Internal Port Range Range Global Internal Type Start End Start End 0 0 0 0 Set to 0 0 0
5. Cancel e Select Confirm Changes BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration LAN Gateway ADSL Modem ETH DM2 Port VoIP ISDN WLAM The following screen is displayed The setup is now complete 5 DMZ Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DM2 Port VoIP ISDN WLAN The default setting of the port is DMZ To change the DMZ IP address t ETHDMZ Port Broadband Module Basic Configuration Status _ System Backup Restore System Restart Advanced Configuration Setup LAM Gateway ADSL Modem ETH DM2 Port VoIP ISDN WLAN e Select Change the DMZ IP address here Broadband Module ETH DMZ Port Confirm The ETH DMZ Port will use an external IP Gateway to provide internet access The Broadband Module WAN address will be 213 94 222 177 The Broadband Module WAN Subnet Mask will be 255 255 255 0 The Internet Gateway address will be 213 94 222 176 The Primary DNS Server will be 212 57 32 1 The Secondary DNS Server will be 212 57 32 2 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel ICEL EU BB LL ET HOS ETH
6. Change your wireless security settings here Change which wireless PCs are allowed to connect here Set the interface for the wireless network here Enable Disable Enable or disable the wireless network here takes you the following screen Broadband Module A ENER WLAN Enable Disable Basic Configuration Status System Backup Restore System Restart Advanced Configuration Enabling wireless networking will allow PCs with wireless network capabilities to connect to the Internet through the Broadband Module 8 Tell me more about the wireless networks Select whether you want wireless PCs to connect to your device Setup C Disable Wireless PCs will not be able to connect to your device LAM Gateway ADSL Modem ETH DMZ Port VoIP ISDM AH AN Enable Wireless PCs will be able to connect to your device Next gt Cancel Two options are presented 53 BT Versatility Broadband Module Broadband Module Plus Manual 1 Disable e Select Next The following screen is displayed Broadband Module BU WLAN Confirm Basic Configuration Status M System Backup Restore System Restart Advanced Configuration Wireless networking will be disabled To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel LAM Gateway e S
7. Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN Select IP Gateway from the ETH DMZ Port Select Next e Two options are presented a DHCP The IP address is automatically assigned by DHCP ETH DMZ Port Mode There are three modes for the ETH DMZ Port available Choose a type that is suitable for your Internet connection from the options below Q Tell me more about ETH DMZ Port settings PPPoE use this if you use PPPoE with an external DSL modem IP Gateway use thi external router or LAN DMZ use this if your internet access is provided on the DSL port and you are using the ETH DMZ Part to host a DMZ Cancel Mode screen ICEL U BB LET DH ETE Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DM2 Port VaTD Select Next The following screen is displayed ETH DMZ Port IP Gateway Mode Choose a type that is suitable for your Internet connection from the options below Tell me more about ETH DMZ Port settings Static use this if you must configure your network settings manually Cancel Select DHCP from the ETH DMZ Port IP Gateway Mode screen Broadband Module B
8. Click ADSL Modem in the Setup menu Click Change the ADSL Modem settings here e PPPoA is selected by default click Next gt Oo Enter the PPP Username and PPP Password retype the password click Next gt The default VPI and VCI values 0 38 are shown if different values are required enter them here click Next gt Q Click Confirm Changes BT Versatility Broadband Module Broadband Module Plus Manual Dyar idap Puertas Shcibem Pers ort Broadband Fiodule Wed Cond iur a Shahin D system Dackup Restore System F start Broadband Module ADSL Modem The ADSL Modem settings cantral how the Braadband Module connects to thi Internet p Tell ma more about MeL My ADSL Modem is currently configured as follows adr Access it provided by DAL PPPoA with VPI af D and a vcl of 3H The PPP Username i The PPP Password rs not sat Change the AD ADSL Modem Types of Access There are five types of Intent Access avadable Choose a type that sc suitable for your Internet connection fram the options below a Tall me rior t ADS g a z S PPPoA use this if you have a PPPOA DSL connection D PPPOE use the if you have a PPPoE DEL connection C OHO use this if you have a DHCP DSL connection C Manual usa this ta configure your connections gateway and DHS servers directly Newt gt Cancel ADSL Modem PPPoA In order to use a PPPoA connection te the Inte
9. Select Next gt BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module broadband Module broadband Hodule Sytem Bache Foectore Syshem estt Advanced Configuration VoIP Satur up vel for the Broadband Module alis you to route tebepheny tais ever a data network aq Tel ma moro about volP Your currant Vobf cattinsgs ang Erdpenst 1 G711 0729 Not Confiquend Endpoint 2 G711 0779 Not Conf quewd Endpoint 3 G711 0729 Not Confiquned Endpoint 4 0711 0729 Not Confiurmd Endpoint 5 0211 0729 Not configuri Endpin amp 62711 0729 Not Confiqured Endpoint 7 G711 729 Not Confiquend Endpoint G111 6729 Set Confiquewd Endpoint 9 711 0729 Mot Comiquend Endpoint 10 0711 0729 Not Confiqured Endpoint 11 0711 0729 Not Configured Endpoint 12 60211 0229 Not Confiqueed Change Vel Endamnt ypsi bere Change Viol Endponint authenticatinm perg Chanos Vel En n iti l i fi Broadband Module VoIP Endpoint Type You should fill out the following fields g Tell me more about volp Extensi n Type Endpont 1 Endpent 2 Endpoint 3 Endpoint 4 Endpoint Endpoint 6 Endpoint 7 Endpont amp Endpont 9 he Endporit 10 Irure Endpoint 11 Inacteg Endpoint 12 Inacteg tet cancel Broadband Module VoIP Confirm The endpoint settings will ba Type Endpoint 1 Inactive Endpant 2 Inactive Endpoint 3 ITP Extn Endpoint 4 ITP Extn Endpoint 5 ITP Extn Endpoint 6 ITP Extn Endpar
10. 0O Admin Accounts Firewall amp Security IP Routes 61 BT Versatility Broadband Module Broadband Module Plus Manual FIREWALL amp SECURITY The BROADBAND MODULE and BROADBAND MODULE PLUS are equipped with a stateful inspection firewall The firewall resides on the interfaces between WAN and LAN External and Internal WAN and DMZ External and DMZ DMZ and LAN DMZ and Internal e Select Firewall amp Security The Firewall Configuration screen is displayed Security State The Firewall is enabled by default Broadband Module E Firewall Configuration Basic Configuration Advanced Configuration ADSL Test Diagnostics SS Flash Update Security State Firewall Enabled Disabled Reset to Defaults Intrusion Detection Enabled Enabled Disabled Advance d Setup Change State Admin Accounts Firewall amp Security To disable the Firewall e Select Disabled e Select Change State Intrusion Detection is disabled by default To enable Intrusion Detection e Select Enabled 62 BT Versatility Broadband Module Broadband Module Plus Manual e Select Change State Security Level There are four pre defined security levels high medium low and none that con
11. Advanced Configuration VPI 0 Setup VCI 38 Next gt Cancel LAN Gateway ADSL Modem ETH DMZ Port 23 BT Versatility Broadband Module Broadband Module Plus Manual VPIACI VPI VCI Virtual Path Identifier Virtual Circuit Identifier specify the ATM connection between the ADSL modem and the service provider The VPI range is O 4095 The VCI range is O 65535 The default values are 0 58 e Enter the VPI and VCI values if they are different from the default values e Select Next The following screen is displayed Broadband Module ADSL Modem Confirm Basic Configuration Status System Backup Restore Internet Access will be provided by DHCP BE system Restart The VPI will be 0 and the VCI will be 38 Advanced Configuration To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel LAN Gateway ADSL Modem e Select Confirm Changes The following screen is displayed TOT Ue Le UT B LES Te LU S Broadband ETE ADSL Modem Basic Configuration Status A System Backup Restore i System Restart Advanced Configuration The ADSL Modem settings control how the Broadband Module connects to the Internet 8 Tell me more about the ADSL Modem settings ADSL Modem is currently configured as follows Restart Required md Internet A
12. Broadband Module DMZ address 192 168 23 Broadband Module DMZ Subnet Mask 255 e5bb e55 Cancel NN NNI Setup LAN Gateway ADSL Modem Enter the new IP address and subnet mask Select Next The following screen is displayed Select Confirm Changes ICEL EUO MO E TET ETH DMZ Port Confirm Basic Configuration Status System Backup Restore System Restart Advanced Configuration The Broadband Module DMZ address will be 192 168 3 1 The Broadband Module DMZ Subnet Mask will be 255 255 255 0 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel Setup LAN Gateway ADSI Modem TOT C T HT BB LL oT V S Broadband snam ETH DMZ Port Basic Configuration Status The ETH DMZ Port settings control how the Broadband Module uses the System Backup Restore ETH DMZ Port A a System Restart Q Tell me more about the ETH DMZ Port settings Advanced Configuration The ETH DMZ Port is currently configured as follows Setu i The ETH DMZ Port hosts a DMZ LAN Gateway Change the ETH DMZ Port settings here ADSL Modem ETH DMZ Port bis The DMZ IP Address is 192 168 3 1 ISDN The DMZ Subnet Mask is 255 255 255 0 WLAN Change the DMZ IP address here The new address settings are displayed 32 BT Versatility Broadband Module Broadband Module
13. Create a new connection Disconnected Change Windows Firewall settings zd LAN or High Speed Internet See Also Local Area Connection J Network Troubleshooter Disabled Other Places Personal Area Network E Control Panel 3 My Network Places My Documents qj My Computer Details Network Connections System Folder Double click the Wireless Network Connection icon Conexant D110 MDC V 9x Mo a Broadcom Netxtreme 57xx Gig Bluetooth Network Connection Disconnected E Bluetooth Device Personal Ar GRICV33 Disconnected LL Conexant D110 MDC V 9x Mo Wireless Network Connection Mot connected LL 9 Intel R PRO Wireless 2200BG 89 BT Versatility Broadband Module Broadband Module Plus Manual i Wireless Network Connection Network Tacks Choose a wireless network q Refresh network list Click an item in the list below to connect to a wireless network in range or to get more XJ Set up a wireless network BTY Demo Room For a home or small office E nf Security enabled wireless network WPA Related Tasks damians_wpa_aim i learn about wireless Unsecured wireless network networking PRISM 01 5f 79 bernar fe Change the order of preferred networks 5B Security enabled wireless network y Change science CSE lab Wireless AIM settings 3 Security enabled wireless network WPA PRISM 01 1f 5d Unsecured wireless network Reservoir sig 5 Security enabled wireless network
14. WPA Connect A list of wireless networks is displayed e Click Change the order of preferred networks Wireless Network Connection Properties AE General Wireless Networks Advanced Available networks To connect to disconnect fram or find out more information about wireless networks in range click the button below View Wireless Networks Prefered networks Automatically connect to available networks in the order listed below Move up Move down Add Remove Properties Learn about getting up wireless network configuration e Click Add 90 BT Versatility Broadband Module Broadband Module Plus Manual Wireless network properties Association Authentication Connection Network name SSID Network 01 Wireless network key This network requires a key for the following Network Authentication WPA PSK V Data encryption TKIP Network kep eeeeeeeaee Confirm network key Tri ii ity C This is a computer to computer ad hac network wireless access points are not used Enter the network name SSID this is the Network Name SSID entered in the WLAN settings in p 43 Select WPA PSK from the Network Authentication drop down menu Select 7K P from the Data encryption drop down menu Enter the network key this is the Pass Phrase entered in the WLAN settings in p 46 Confirm the network key Click OK 91 BT Versatility Broadband Module Broadband Module Pl
15. available on the broadband connection for IP trunks and extensions BT Versatility Broadband Module Broadband Module Plus Manual IP Trunk or Extension G 711 100 kb s G 729 50 kb s NUMBER OF VOIP CHANNELS The following chart shows the bandwidth required to support up to 12 VolP channels When calculating the number of VoIP channels that can be used over ADSL always use the lower upload data rate Note that data applications for browsing etc will require additional bandwidth BT Versatility Broadband Module Broadband Module Plus Manual QUICK SETUP CONNECTING A PC TO THE LAN o Power up the PC e9 Connect the Ethernet port on the PC to any LAN port 1 4 on the MDF using a Cat 5 cable patch cord amp Check that the LED on the MDF cover for the port the PC is connected to is lit permanently This indicates a good Ethernet connection between the PC and the Broadband Module RESET o BUTTON ADSL T 2 10 BASE T WAN 4 ASDL X21 LANPORT1 LAN PORT WAN LAN PORT 3 LAN PORT 4 SET UP THE PC TO AUTOMATICALLY OBTAIN AN IP ADDRESS e Click Start and Control Panel Internet Internet Explorer E mail 5 Microsoft PowerPoint Lotus Notes QOG Microsoft Word A X Encore CX eyeBeam a AJ Adobe Reader 6 0 NZ BT Versatility Wizard isss J555 3 3 Lite My Documents O My Recent Documents gt i My Picture
16. Add Hardware Add or Administrative Automatic Bluetooth Broadcom ASF e Switch to Category View Options Remoy Tools Updates Devices Configuration See Also 2 i c cx Ay 7 Broadcom Date and Time Display Find Fast Folder Options Fonts Game o Windows Update Control Suite Controllers Ip and Q9 Help and Support I E S te v PL Intel R GMA Internet Java Plug in Keyboard Mouse Network PatchLink Driver for Options Connections Update Be 2 3S 7v Phone and Portable Media Power Options Printers and Regional and Scanners and Scheduled Modem Devices Faxes Language Cameras Tasks e 1 9 s Security SigmaTel Sounds and Speech System Taskbar and User Accounts Center Audio Audio Devices Start Menu e x Windows Wireless Firewall Network Set e Double click the Network Connections icon M Network Connections File Edit View Favorites Tools Advanced Help Q Back pe Search ic Folders E Address Network Connections Network Tasks 5 Create a new connection Change Windows Firewall settings RAS LAKE GRICV33 Disconnected Disconnected C as Conexant D110 MDC V 9x Mo LL Conexant D110 MDC V 9x Mo LAN or High Speed Internet Local Area Connection Wireless Network Connection Disabled Mot connected E A Broadcom Netxtreme 57xx Gig L p Intel R PRO Wireless 2200B6 See Also Yi Network Troubleshooter Other Places E Control Panel My Ne
17. C LAN Wireless PCs will be able to connect to your LAN devices Next Cancel LAN Gateway ADSL Modem ETH DMZ Port VoIP In order to provide maximum security PCs connected to the WLAN are not allowed to program the module via the web interface If programming from a wireless network PC is required the WLAN interface should be changed from DMZ to LAN e Select an option e Select Next The following screen is displayed TOT Ce Le UT B OL LU S de Broadband CENE WLAN Confirm Basic Configuration Status Wireless networking is set to operate in United Kingdom J System Backup Restore Wireless networking type is 802 11B G RH System Restart Advanced Conon Wireless networking will be enabled The wireless network name SSID will be set to PRISM 01 1f 54 The Broadband Module will automatically select the best wireless channel The wireless networking security will be set to Wi Fi Protected Access WPA SSID Broadcast will be enabled Only the wireless PCs shown below will be allowed to connect to the wireless network Restart Required To implement your changes a restart is required Restart Setup D0 10 36 03 2C 08 The wireless network will be on the DMZ To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel LAN Gateway ADSL Modem ETH DMZ
18. DHCP server will operate on Name Delete iplan F ipdmz F Add new interface There is an option to tell the DHCP server to operate on the ipwan interface Add new interface Use this section to tell the DHCP server to operate on another IP interface New IP interface ipwan Adc 11 BT Versatility Broadband Module Broadband Module Plus Manual Existing DHCP Server Subnets Existing DHCP server subnets Use Use local local h Assign Get host pal Auto subnet Subnet Yalue Subnet Mask address Delete address m Domain from IP as DNS Name interface default server gateway 192 168 1 0 255 255 255 0 lipan r idad 160 1 200 200 true true true Iplan Options Advanced 192 168 0 0 255 255 255 0 true tue tue ipdmz r T Apply Reset Create new Subnet O Help The settings for the existing subnets on the iplan and ipdmz are displayed All displayed parameters can be changed change the setting to a new value and click Apply To delete a subnet check the associated box and select Apply To create a new subnet e Select Create new subnet The screen displayed is the same as Edit DHCP server subnet in the following section Advanced Options e Select Advanced Options Parameters for this subnet Edit DHCP server subnet This page allows you to change an existing DHCP server subnet This can Include moving the subnet offering a different range of addre
19. Gateway ADSL Modem FTHINM Port ADSL Modem Confirm Internet Access will be provided by PPPoA The VPI will be O and the VCI will be 38 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel The new parameters are saved and the new ADSL Modem settings are displayed 20 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module NOS Broadband FUE ADSL Modem Basic Configuration Status _ System Backup Restore id System Restart Advanced Configuration The ADSL Modem settings control how the Broadband Module connects to the Internet Q Tell me more about the ADSL Modem settings ADSL Modem is currently configured as follows Restart Required To implement your changes a restart is required Restart Internet Access is provided by DSL PPPoA with a VPI of 0 and a VCI of 38 The PPP Username is username The PPP Password is set Change the ADSL Modem settings here e Restart the module The ADSL Modem setup is now complete 2 PPPoE This option uses Point to Point Protocol over Ethernet e Select PPPoE from the ADSL Modem Types of Access screen Broadband Module Broadband Module ADSL Modem Types of Access Basic Configuration Status 4 System Backup Restore i System Restart Advanced Configuration T
20. Plus Manual VoIP Manually Configuring IP trunks A broadband connection must first be established before the IP Endpoints can be programmed e Select VoIP from the Setup menu The following screen is displayed TPR Module VolP Basic Configuration Status Setting up VoIP for the Broadband Module allows you to route telephony System Backup Restore calls over a data network Tell me more about VoIP System Restart Advanced Configuration Your current VoIP settings are Setup Endpoint 1 G711 G729 Not Configured EAN Gateway Endpoint 2 G711 G729 Not Configured ADSL Modem ETH DMZ Port Endpoint 3 G711 G729 Not Configured VoIP Endpoint 4 G711 G729 Not Configured ISDN Endpoint 5 G711 G729 Not Configured WLAN Endpoint 6 G711 G729 Not Configured Endpoint 7 G711 G729 Not Configured Endpoint 8 G711 G729 Not Configured Endpoint 9 G711 G729 Not Configured Endpoint 10 G711 G729 Not Configured Endpoint 11 G711 G729 Not Configured Endpoint 12 G711 G729 Not Configured Change VoIP Endpoint types here Change VoIP Endpoint authentication here Change VoIP Endpoint additional options here e Select Change VoIP Endpoint types here The following screen is displayed quesemeyueUE VoIP Endpoint Type a Basic Configuration Status You should fill out the following fields System Backup Restore Tell me more about VoIP System Restart Advanced Configuration Extension Type Endpoint 1 Trunk Setup End
21. for user admin Username admin Password mem Comment Created by CLI Cancel and return to Admin Accounts Setup Page O Connect to 192 168 1 1 Webadmin User name Password P engineer hr Remember my password Log in to the browser programming interface using the default username password engineer engineer e Go to Advanced Setting e Select Admin Accounts 60 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is displayed The following page is displayed Select Edit user Enter a new password Select Apply ICEL EU MT T EER Admin Accounts Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults This page allows you to control access to your router s console and these configuration web pages Currently Defined Users User Comment admin Createdby CLI engineer Created by CLI Edit user Advanced Setup Admin Accounts Firewall amp Security IP Routes Fu Im Pesce Broadband Module Broadband Module Admin Accounts edit user engineer Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Details for user engineer Username engineer Password jeeeesesee Comment Created by CLI Apply Reset Cancel and return to Admin Accounts Setup Page
22. iT e C e LT B LL EST LU TETEE ETH DMZ Port Confirm Basic Configuration Status System Backup Restore System Restart Advanced Configuration The ETH DMZ Port will use PPPoE to provide internet access To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel Setup LAM abaris e Select Confirm Changes The following screen is displayed Broadband Module E EM Broadband Faas ETH DMZ Port Basic Configuration Status The ETH DMZ Port settings control how the Broadband Module uses the System Backup Restore ETH DMZ Port oar System Restart Q Tell me more about the ETH DMZ Port settings Advanced Configuration The ETH DMZ Port is currently configured as follows Setup 5 The ETH DMZ Port uses PPPoE to provide internet access LAM Gateway ADSL Modem The PPP Username is ETH DM2 Port The PPP Password is not set VoIP ISDN WLAN Change the ETH DMZ Port settings here The DMZ IP Address is 192 168 0 1 The DMZ Subnet Mask is 255 255 255 0 Change the DMZ IP address here The ETH DMZ port is now set up to connect to an external ADSL modem 28 BT Versatility Broadband Module Broadband Module Plus Manual 2 IP Gateway IP Gateway is used when connecting to another LAN or WAN via an external router iT eT e er HT B LoT DH LS
23. module is equipped with the following ports for Wide Area Networking ADSL RJ 11 This is for wires only ADSL service ITU T G 992 1 Annex A G DMT and ITU T 992 2 G Lite are supported ETH DMZ Port RJ 45 This port supports10 100 Ethernet FDX HDX and is used to connect to an external broadband gateway or DMZ host It does not support MDI MDI X ISDN N A A single 64 kb s dial up connection can be established over any ISDN line connected to the PBX BT Versatility Broadband Module Broadband Module Plus Manual EXAMPLES The on board ADSL modem is used to connect to the Internet using a wires only service See page 10 Ip E l Ex s N E I i Splitter aie rion o AX Internet The ETH DMZ port is used to connect to an external SDSL or Cable modem See page 27 Line Internet LAN PORT LAN PORT 4 The ETH DMZ port is used to connect to a Gateway into a private network See page 27 Private Network BT Versatility Broadband Module Broadband Module Plus Manual ROUTES A single route using PPP including PPPoE and PPPoA and a second route using static or dynamic IP are concurrently supported The following comb
24. provide you with a username and password when you sign up for their service 8 Tell me more about the PPP username and password PPP Username username PPP Password eeeeses Retype the PPP Password eeeeee Next Cancel Enter a Username and Password Retype the Password Select Next The following screen is displayed VPI VCI VPI VCI Virtual Path Identifier Virtual Circuit Identifier specify the ATM connection between the ADSL modem and the service provider The VPI range is O 4095 The VCI range is 0 65535 The default values are 0 38 TOT C eT HT BB LL Te LV S Broadband Module Basic Configuration Status System Backup Restore iat System Restart Advanced Configuration Setup LAM Gateway ADSL Modem ETH DMZ Port VoIP ADSL Modem Manual VPI and VCI Setup The Broadband Module needs to know which YPI and VCI it should use for Internet Access Enter the VPI and VCI values that your ISP has provided in the boxes below Q Tell me more about choosing VPI and VCI values VPI 0 VCI 38 Next gt Cancel Enter the VPI and VCI values if they are different from the default values Select Next The following screen is displayed Select Confirm Changes ICEL EU BB LL EeTO DH ETE Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration LAN
25. server fo specify its own IP address by clicking on the Use local host address as ONS server checkbox Primary DNS server address 0 fo Secondary DNS server address 0 at a a Use local hast address as ONS server v The default setting is use local host as the DNS server all DNS requests are sent to the default gateway 192 168 1 1 which then relays the request to the DNS addresses negotiated at start up Specific DNS servers can be defined if required Default gateway option information Default gateway option information Use local host as default gateway iv Use local host as default gateway is checked by default Additional option information Additional option information Aad and remove items from this list to configure additional option Information you would ike the DHCP server to give to clients on this subnet Create new DHCP option 3 OK Reset Cancel e Select Create new DHCP option The following screen is displayed 79 BT Versatility Broadband Module Broadband Module Plus Manual Create DHCP server configuration option This page allaws you to set up a new DHCP server configuration option that will be sent to DHCP clients on this subnet Create new DHCP option Choose which option you would tke to configure using the drop gown list Then fin the text box to specity what will be sent to DACP chants if they should request a value for the chosen option Some of the options such a
26. 0 to use the primary icmp o fo fo o IP address of the interface ipwan Add Reserved Mapping 66 BT Versatility Broadband Module Broadband Module Plus Manual e Enter the following parameters Global IP address This is the public IP address assigned to the WAN interface Internal IP Address This is the internal IP address of the server on the LAN Transport Type Select a protocol from the drop down list External Port A port or port range can be defined for the external IP Range address Internal Port A port or port range can be defined for the internal IP Range address e Select Add Reserved Mapping Policies Triggers Intrusion Detection Logging The security policy settings stateful inspection triggers intrusion policy detection and logging settings can be displayed and changed Security Policy Three types of filters can be defined in the firewall Port Filters are used to allow or block a specific TCP IP application level protocol The parameters used to specify this filter are source and destination IP address or range of addresses a transport level protocol TCP UDP ICMP and a port or range of ports which define the application level protocol Raw IP Filters are used to allow or block a specific protocol non TCP IP carried within an IP packet The parameters used to specify this filter are source and destination IP address or range of addresses and a protocol number which
27. 00 metres This assumes clear line of sight between a remote PC and the BBM As the coverage is distance dependent any obstruction caused by walls etc will reduce the operating range Quick Setup to WLAN without security This procedure should only be used to setup and test WLAN connectivity When this procedure has been completed and WLAN connectivity has been established go to the next section Setting up WLAN with Security and complete the process e Select WLAN in the Setup menu The following screen is displayed Scroll down to General Settings General Settings Your current wireless network settings are Wireless networking is disabled so wireless PCs can not connect to your device Enable or disable the wireless network here The Broadband Module is automatically selecting the best wireless channel to use The channel currently in use is 1 Change your wireless channel here The wireless network name SSID is PRISM 01 1f 81 Change your wireless network name SSID here Wireless network security is using Wi Fi Protected Access WPA The WPA pass phrase is not currently set SSID Broadcast is disabled Change Wireless Security settings here Any wireless PCs are allowed to connect Change which wireless PCs are allowed to connect here The wireless network is on the DMZ so wireless PCs have restricted access to your LAN devices Set the interface for the wireless network here There are curre
28. 5060 Security Trigger A security trigger can be defined for applications that are not supported by the ALGs listed above A security trigger allows the firewall to dynamically open and close secondary ports associated with a particular application and to specify the maximum length of time the port remains open Policies Triggers Intrusion Detection Logging Security Policy Configuration O Security Trigger Configuration Configure Intrusion Detection Q Configure Security Logging e Select Security Trigger Configuration The following screen is displayed 71 BT Versatility Broadband Module Broadband Module Plus Manual Security Trigger Configuration Current Security Triggers Security Triggers Secondary Secondary Enable Port Port Allow Max Enable Bi patted lala Number Number Hai Ban Multiple Activity Session He Ad Ore Start End Number Number Hosts Interval Chainin mn Reple Start End g Chaining p tcp 1720 1720 1024 65535 false 30000 true false true udp 51200 51201 1024 65535 false 3000 false false false tcp 51210 51210 1024 65535 false 3000 true false false New Trigger Return to Interface List Current security triggers are displayed There is an option to delete each entry e Select New Trigger The following screen is displayed Security Add Trigger 72 Transport Type Port Number Start Port Number End Secondary Port Number Start Secondary Port Number End All
29. BI Versatility Communication without complication Broadband Module Broadband Module Plus BT Versatility Broadband Module Broadband Module Plus Manual Table of Contents INTRODU GION 1 CONNE TION Senet ener teeter nnn RRR E E REAR tnt nnn nn nn DO DOCE OCC CD tnnennr rrr 2 INDICATORS cecescceceeccecsessenceeseessessenseeseessenseeseeseessessenseessessesseeseessenses 2 RESETIBUT TON orn N T N TON O 5 LOCALAREA NETWORK d cccesceeetiacauctudeeinancandaneeaataueeneeeccautaeedeeeceauceneeneeead 5 WV IDE AREANETWORK ccasttaitacceeadeaiedcnmseeeeeeieaineeemiaaaenediinecaaecaedainaceaasaaceaage 5 PON ssa ETE UTERE 5 EXGIMDICS RN TED E eee eee eeesesnenk 4 PROU CC Sissel cia MP M 5 PIR EVV 5 fo eee eee eee eT eT Te er TT TT nner ee 5 Bandwidth Requirements 5 ssc rere rp er ERN SRO OPE doy ashe aes EU etexs oo er tea ves ee t pR SEE 5 Number of VolP Channels ri proe teoP Che ha E ERE ren TREV ET cH Eb P iere etie to Lee 6 ames m TE 7 Connecting a PC to the LAN ses tescabsss dea atout otv si a do Pre iS cu epe a m bet edes 7 Set up the PC to automatically obtain an IP address eee 7 Setting up the BFOWSeEF iei root o toto o aede eui UE RUn E REN TEUER eR Mo bI vs se REP SR LOK rupes aU sean 9 Connecting
30. Basic Configuration Status System Backup Restore i System Restart Advanced Configuration Select the MAC address to remove below 8 Tell me more about restricting wireless access 00 1 0 36 03 2C 06 00 10 36 03 2C 06 Restart Required Cancel To implement your changes a restart is e Select the address to remove from the drop down menu e Select Next this takes you back to the Only allow the wireless PCs specify to connect option Two options are presented for the WLAN Interface DMZ this is the default setting where the WLAN normally resides on the DMZ Recommended LAN see screen warning re security iT fer er Ee B LET LO LES D eaan End Module WLAN Select Interface Basic Configuration Status System Backup Restore Eid System Restart Advanced Configuration If you place the wireless network on the LAN your LAN PCs and devices may be exposed to attack over the wireless network It is usually more secure to place the wireless network on the DMZ This restricts access from the wireless network to LAN devices but permits internet access from the wireless network Restart Required To implement your changes a restart is required Restart Setup Q Tell me more about the wireless networks Select whether you want wireless PCs to be a part of your DMZ or your LAN DMZ Wireless PCs will have restricted access to your LAN devices
31. Block Duration Scan Detection Threshold Scan Detection Period Port Flood Detection Threshold Host Flood Detection Threshold Flood Detection Period Maximum TCP Open Handshaking Count Maximum Ping Count Maximum ICMP Count Enables or disables the blocking of incoming broadcast Ping commands for the period specified in Victim Protection Block duration The period for which incoming broadcast Pings are blocked The default setting is 600 seconds If a Denial of Service attack is detected traffic from that host is blocked for the duration specified here The default setting is 1800 seconds If scan activity from a host attempting to identify open ports is detected traffic from that host is blocked for the duration specified here The default setting is 86400 seconds 1 day If the number of scanning packets counted within the Scan Detection Period exceeds the value set here a port scan attack is detected The default setting is 5 per second The duration that scanning type traffic is counted for The default setting is 60 seconds This is the maximum number of SYN packets that can be received by a single port before a flood is detected The default setting is 10 per second This is the maximum number of SYN packets that can be received from a host before a flood is detected The default setting is 20 per second If the number of SYN floods counted within this duration exceeds either the Port Flood Detection
32. CdtS 57 WEAN cr 41 Quick Setup to WLAN without security ssseeeeeeeenn nennen 41 Connecting your PC to the Wireless Network eese 43 Setting tb VV LEAN wth OCU CY uis adusta eta E ELE E a C DIE led 45 TO rT on 55 SISTEMA BACRUPURESLORE 0500000000000 ooo eet OOo eo Ope Op eoe et oO DOE nope ODE 56 DXSTEMLTSESTARIDouUSum0 05050950590405900009500490004002000029590025092299025915 9000009400990 0094 58 ADVANCED CONEIGURA TION mescteEIPDIEPNEIPDIRII DINE PD IEPUESI DUREE ID EDS DEDE EE EE 59 Ami ACCOUES 155 oie ooo inco bE ied edeces ioco fepe Ao dodatun iE aes quie E a ons i16 59 Firewall G Secufity c o ciae uo seo res sore e redo sa ie ROV E ee ended EI DU dub o awed siemens 62 p51 1 49 dL AY As San Or cocus setas ot put Pe D ME MED T Ln ere ics del en 62 je eI A OV ON Sas n cds ar cate ea scat seats ner cas vaca tare ava tne aca E sare cua sate maces 63 Security HE g gt lt e ee a ies 64 BT Versatility Broadband Module Broadband Module Plus Manual Policies Triggers Intrusion Detection Logging sse 67 I ROUEBS staked pate rte a e eR ieu ate eM cu M ME EL M LA OC Me Sod eh eat dr 76 DACP SENE sian E T mmm 77 Advanced SDN NER TTE 81 PRS UL E c PERENNE 85 DSE S taS eae sie RTT KE 84 Pi ACIOS CCS NE TR ET OTT 85 T qui Solo ERR NER TORT E A E E 85 ad fe TEN EON EE AE 86 AS UPDATE eosin cet
33. DMZ Port The ETH DMZ Port settings control how the Broadband Module uses the ETH DMZ Port Q Tell me more about the ETH DMZ Port settings The ETH DMZ Port is currently configured as follows The ETH DMZ Port is configured to use an external IP Gateway to provide internet access The WAN IP Address is 213 94 222 177 The WAN Subnet Mask is 255 255 255 0 The Default Gateway is 213 94 222 176 The Primary DNS Server is 212 57 32 1 The Secondary DNS Server is 212 57 32 2 Change the ETH DMZ Port settings here The DMZ IP Address is 192 168 0 1 The DMZ Subnet Mask is 255 255 255 0 Channe the nM7 ID address here ETH DMZ Port The ETH DMZ Port settings control how the Broadband Module uses the ETH DMZ Port Tell me more about the ETH DMZ Port settings The ETH DMZ Port is currently configured as follows The ETH DMZ Port hosts a DMZ Change the ETH DMZ Port settings here The DMZ IP Address is 192 168 0 1 The DMZ Subnet Mask is 255 255 255 0 Change the DMZ IP address here 31 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is displayed J ETH DMZ Port DMZ Setup Broadband Module Broadband Module ETH DMZ Port DMZ Setup Basic Configuration Status System Backup Restore System Restart Advanced Configuration To setup your DMZ port you must provide values for the fields below 8 Tell me more about DMZ Setup settings
34. IP address to allow NAT traversal Address Translation Type Sets address replacement on a particular packet type e Select Apply Intrusion Detection This is used to detect and block incoming attempts to attack or block traffic to the site Policies Triggers Intrusion Detection Logging Security Policy Configuration Q Security Trigger Configuration Q Configure Intrusion Detection Q Configure Security Logging 9 e Select Configure Intrusion Detection The following screen is displayed Use Blacklist false Use Victim Protection false Victim Protection Block Duration 600 seconds DOS Attack Block Duration 1 Bn seconds Scan Attack Block Duration 86400 seconds Scan Detection Threshold 5 per second Scan Detection Period E seconds Port Flood Detection Threshold IT per second Host Flood Detection Threshold 20 per second Flood Detection Period In secands Maximum TCP Open Handshaking Count l5 per second Maximum Ping Count 15 per second Maximum ICMP Count 100 per second Apply Clear Blacklist Return to Interface List e Enter the following parameters Use Blacklist Enables or disables blacklisting of an external host if the firewall has detected an intrusion from that host Access is denied to that host for 10 minutes 73 BT Versatility Broadband Module Broadband Module Plus Manual 74 Use Victim Protection Victim Protection Block Duration DOS Attack Block Duration Scan Attack
35. N Type options are presented WLAN WLAN Type Selection Select the type of wireless network you wish to use 8 Tell me more about wireless types AN 802 11B G Continuing beyond this page will clear your other wireless settings so you will be asked to enter them again C 802 11B only C 802 11G only Confirm Changes Cancel 802 11 B G operates at 11 Mb s or 54 Mb s Recommended 602 11 B only operates at 11 Mb s 802 11 G only operates at 54 Mb s e Select an option 46 BT Versatility Broadband Module Broadband Module Plus Manual e Select Confirm Changes The following screen is displayed iT OT Ce Le UT B LES Te LU LS Broadband Modul WLAN Basic Basic Configuration Status System Backup Restore System Restart Advanced Configuration Before a wireless network can operate you need to provide a name SSID for the network Network Name SSID PRISM 01 1f 54 Next Cancel Restart Required A Ta imnl lamant voie The default Network Name SSID is displayed This name can be changed if required Enter the Network Name SSID in the table provided in Appendix A as it is required when setting up PCs for wireless networking e Select Next The following screen is displayed Broadband Module us 1 WLAN Channel Selection Basic Configuration Status System Backup Restore 7 System Restart Advanced Configur
36. N interface should be changed to LAN page 51 Connect to 192 168 1 1 2 xl o Launch the browser on any PC connected to the LAN FA enter OHhitp 192 168 1 1 in the address field press return im WebAdmin User name Gadmn ttt e9 Enter User name admin and Password admin TET Bom o Cancel e The Basic Configuration screen is displayed Broadband Module Basic Configuration Basi Configuration Qabus This page shows general status information about the Broadband Module System Backup Restore Q Ime more about the status information Internet Access settings Internet Access is provided by the ADSL Modem The default gateway rs not currently set ECTHIONZ Port VoIP No name DNS servers have been configured ISDN WLAN About the Broadband Module The hardware revision for the Broadband Module is C The firmware version for the Broadband Module is 134 SETTING UP ADSL The module contains an on board ADSL modem The connection to the modem is via an RJ 11 connector on the MDF Obtain the following information from your ADSL service provider RESET Username Password Splitter 7 Type of Access VPI and VCI values ii E 1OBASETWAN ASDL_ 3 4 Q X LANPORTI LAN PORT 2 Connect the data port on the splitter to gwn 1 8 the ADSL RJ 11 port on the MDF Connect the telephone port on the splitter to a telephone or fax machine LAN PORT3 LAN PORT 4 10 e9 Enter the programming menu
37. PIMAC mapping Add new mapping Define your new fixed manong here The IP address you choose will be given to the host with the MAC address you specity The IP address must not clash with an IP address already present in a dynamic address range You should also ensure that there is suitable subnet defined for the IP acdress to reside in The MAC address should be expressed as 6 hexadecimal pairs seperated by colons e g 00 20 25 02 02 03 IP address MAC address Maximum lease time 259200 seconds OK Reset Cancel Enter the IP address to be assigned to the host Enter the MAC address of the host Enter the maximum lease time in seconds Select OK ADVANCED ISDN Additional optional ISDN settings can be entered here e Select Advanced ISDN from the Advanced Configuration menu Call Log This option is used for system maintenance and is disabled by default Edit PPPolsdn Settings Call Log The ISON Call Log is currently disabled To retrieve the ISDN Call Log right click here and select Save Target As Disabled Do nat log ISDN Calls C Enabled Log ISDN Calls made for the next 5 days Apply Options Additional parameters can be entered for ISDN 81 BT Versatility Broadband Module Broadband Module Plus Manual Backup Telephone Number Number of Retries Retry Interval Initial Period Recurring Period Idle Timer 82 Options Name Value Backup Telephone Numb
38. Port VoIP 52 BT Versatility Broadband Module Broadband Module Plus Manual The WLAN parameters are displayed e Select Confirm Changes e Restart the module Go to Appendix A when setting up PCs for wireless networking General Settings These are used to change individual settings after the wireless network has been initially set up General Settings Your current wireless network settings are Wireless networking is enabled so wireless PCs can connect to your device Enable or disable the wireless network here The Broadband Module is automatically selecting the best wireless channel to use The channel currently in use is 11 Change your wireless channel here The wireless network name SSID is PRISM 01 1f 54 Change your wireless network name SSID here Wireless network security is off SSID Broadcast is enabled Change Wireless Security settings here Only the wireless PCs you have specified are allowed to connect Change which wireless PCs are allowed to connect here The wireless network is on the DMZ so wireless PCs have restricted access to your LAN devices Set the interface for the wireless network here There are currently O wireless PCs connected View details of connected wireless PCs The links listed below allow you to change individual network settings used in the initial setup as previously described Change your wireless channel here Change your wireless network name here
39. SL connection etup m M C DHCP use this if you have a DHCP DSL connection LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDM WLAN C Manual use this to configure your connection s gateway and DNS servers directly Cancel e Select Next The following screen is displayed Broadband Module ER ADSL Modem RFC1483 Mode Basic Configuration Status There are four types of RFC1483 connection available Choose a type that L System Backup Restore is suitable for your Internet connection from the options below aa System Restart 8 Tell me more about ADSL Modem settings Advanced Configuration LLC Bridged C LLC Routed C wCMux Bridged Setup LAM Gateway ADSL Modem C V CMux Routed ETH DMZ Port VoIP ISDN WLAN Enable Link State Monitoring Next gt Cancel e Select one of the following modes Your service provider will advise you on the mode to be selected LLC Bridged LLC Routed VCMux Bridged VCMux Routed Enable Link State Monitoring should be ON e Select Next Broadband Module zd Broadband Module ADSL Modem Manual VPI and VCI Setup Basic Configuration Status The Broadband Module needs to know which YPI and VCI it should use for System Backup Restore Internet Access Enter the VPI and VCI values that your ISP has provided in the boxes below System Restart 8 Tell me more about choosing VPI and VCI values
40. T operates independently on each interface and is enabled by default on each of the three interfaces internal To disable NAT Security Interfaces Name Type NAT Disable NAT to internal interfaces ipwan external n Disable NAT to DMZ interfaces Advanced NAT Configuration O Disable NAT to internal interfaces Advanced NAT Configuration y ipdmz dmz iplan internal May be configured on external or DMZ interfaces Add Interface 9 al interfaces defined e Select Disable NAT to Interface e Restart the module Global Address Pools A global address pool is used to assign a range of public IP addresses to a WAN interface This can be used in conjunction with Reserved Mapping to associate the public IP addresses on the WAN interface with specific servers applications on the DMZ or LAN e Select Advanced NAT Configuration The following screen is displayed 65 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband Module Advanced NAT Configuration ipwan Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Global Address Pools No Global Address Pools Add Global Address Pool e Select Add Global Address Pool The following screen is displayed
41. Threshold or the Host Flood Detection Threshold traffic from the attacker is blocked for the DOS Attack Block Duration The default setting is 10 seconds This is the maximum number per second of unfinished TCP handshaking sessions that are allowed before a DOS attack is detected The default setting is 5 per second This is the maximum number of Pings per second that are allowed before a DOS attack is detected This is the maximum number of ICMP packets per second that are allowed before a DOS attack is detected Select Clear Blacklist if you wish to clear all external hosts from the blacklist Select Apply Save Configuration Restart the module Security Logging The following page is displayed BT Versatility Broadband Module Broadband Module Plus Manual Policies Triggers Intrusion Detection Logging Security Policy Configuration Security Trigger Configuration Q Configure Intrusion Detection Q Configure Security Logging Q e Select Configure Security Logging Security Logging State Security Logging is enabled Disable Security Lagging Security Event Logging States sofa IN Status State Level Output to Type Enabled notice Session Level notice Disable Console Logging Output ta Change Event Log Enabled notice Blacking Level notice Disable Console Lagging Output ta Change Event Log Enabled notice Intrusion Level notic
42. able from the service provider The range is between O and 60 minutes The default setting is 5 min The Recurring period defines the recurring billing period The range is between O and 60 minutes This can be set by the user to the recurring billing period of the ISDN call This information is available from the service provider The range is O to 60 minutes The default setting is 5 min The Idle timer monitors the call for a period before the expiry of the initial billing period and subsequent recurring periods If no data is present during the idle timer period the call is automatically disconnected at the end of that billing period The default setting is 30 secs and the range is O 120 secs If the Initial Period and the Recurring Period are set to zero no cost control is applied and the call will always remain connected BT Versatility Broadband Module Broadband Module Plus Manual regardless of whether data is present or not until the call is manually disconnected If the Initial Period is set to zero and the Recurring period is set to a non zero value then the call is only monitored for idle periods during the Recurring Period If the Initial Period is set to a non zero value and the Recurring Period is set to zero then the call is only monitored for idle periods during the Initial Period If the call is still connected after the Initial Period it will remain connected until manually disconnected Maximum Calls day A c
43. ack 45 DSL Broadband 2 ETH DMZ Port 4 28 Event logging 59 filter 56 Firewall 2 5 54 Fixed Host IP Address 49 Global Address Pools 57 Host Validators 41 ICMP 46 Indicators 5 Installation 2 Intrusion Detection 5 55 44 IP Gateway 25 ISDN 2 41 65 LAN Gateway 9 Local Area Network 2 4 Event Logging 5 BT Versatility Broadband Module Broadband Module Plus Manual Management 2 Manual addressing 20 MDF 2 NAT 56 Network Address Translation 5 56 BT Versatility Wizard 6 Packet Filter 5 Password Ping 46 Port 4 40 Port Flood attack 45 PPPoA 13 PPPoE 15 Programming 6 Quality of Service 5 Raw Filter 40 Registrar Proxy 29 Reserved Mappings 38 Reset Button 4 routes 4 58 Security State 55 Security Level 55 Security Interfaces 54 56 Security Trigger 43 SIP 29 Static IP address 26 Username 7 Victim Protection 45 VoIP 2 5 29 VPIACI 14 Wide Area Network 2 4 Wireless Networking 42 93 BT Versatility Broadband Module Broadband Module Plus Manual BT Versatility BROADBAND MODULE BROADBAND MODULE PLUS Manual Issue 5 July 2007 Part number LR 2751 51001 5 CE The CE Marking on this equipment indicates Compliance with the following This device conforms to Directive 1999 5 EC on Radio Equipment and Telecommunications Terminal Equipment as adopted by the European Parliament And Of The Council BTO Offices Worldwide The telecommunic
44. all counter sets a threshold on the maximum number of ISDN calls allowed per day When this threshold is exceeded ISDN is disabled This is designed to control the number of calls inadvertently made by applications without the knowledge of the user The range is O 1000 When this is set to O the default setting there is no limit on the number of calls that can be made The counter is automatically set to zero at midnight each day Auto Recovery On When enabled the auto recovery timer becomes active Auto Recovery Timer A timer option is provided to automatically re enable the ISDN after the retry threshold is reached The timer range is 1 120 minutes The default setting is 30 minutes e Enter the new parameters e Select Change Reset restores the default values ADSL TEST This performs a series of diagnostic tests on the ADSL connection and displays the test results Broadband Module Broadband m ADSL Test Basic Configuration Advanced Configuration Perform an ADSL test on your device to identify any problems with your ADSL Test Internet connection B Diagnostics 8 Tell me more about performing an ADSL test Flash Update Reset to Defaults To perform an ADSL test please ensure your device is connected to your phone line and press the Perform ADSL Test button below A test may take several minutes to complete please do not interrupt the check during this time Before running an ADSL test you may want to mon
45. and Module Broadband Module Plus Manual e Select Confirm Changes The following screen is displayed Broadband Module A Basic Configuration Status System Backup Restore System Restart Advanced Configuration Restart Required To implement your changes a restart is required Restart Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN Restart the module Additional Endpoint Options VoIP Setting up VoIP for the Broadband Module allows you to route telephony calls over a data network 8 Tell me more about VoIP Your current VoIP settings are IP Trunk 1 IP Trunk 2 Endpoint 3 Endpoint 4 Endpoint 5 Endpoint 6 Endpoint 7 Endpoint 8 Endpoint 9 Endpoint 10 Endpoint 11 Endpoint 12 Change VoIP Endpoint types here G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 G711 G729 23456789 34567890 Not Configured Not Configured Not Configured Not Configured Not Configured Not Configured Not Configured Not Configured Not Configured Not Configured Change VoIP Endpoint authentication here Change VoIP Endpoint additional options here There are three additional parameters for each IP Endpoint Change VoIP Endpoint additional options here Broadband Module i Basic Configuration Status t System Backup Restore System Restart Advanced Configuration Restart Required To implement your cha
46. ation You may either choose a channel yourself or allow the Broadband Module to automatically select the best channel 3 Tell me more about wireless channels Allow the Broadband Module to select channel C Select a channel manually Next gt Cancel To implement your changes a restart is required Two options are presented for selecting a channel 1 Allow Internet Module to select channel Recommended e Select Next this takes you to Security page 47 2 Select a channel manually e Select Next The following screen is displayed Broadband Module Broadband Module WLAN Channel Selection Basic Configuration Status System Backup Restore System Restart Advanced Configuration Select the channel you wish the wireless network to use 8 Tell me more about wireless network channels Channel 5 Next gt Cancel e Select a channel from the drop down menu e Select Next The following screen is displayed 47 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband Module Basic Configuration Status System Backup Restore ae System Restart Advanced Configuration Restart Required To implement your changes a restart is required Restart Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP Enable SSID Broadcast WLAN Security It is highly recommended that Wi Fi Prote
47. ations services described in this publication are subject to availability and may be modified from time to time Services and equipment are provided subject to British Telecommunications plc s respective standard conditions of contract Nothing in this publication forms any part of any contract British Telecommunications plc 2008 Registered Office 81 Newgate Street London EC1A 7AJ Registered in England No 1800000 Produced by BT Business Information Systems Marketing Cover designed by H amp P Graphics Limited 9968 PHME 42397 05 05 Part No 2731 31000 4 Printed on paper which meets international environmental standards
48. ccess is provided by DHCP with a VPI of 0 and a VCI of 38 To implement your Change the ADSL Modem settings here changes a restart is required Restart e Restart the module The ADSL Modem setup is now complete 4 Manual This option uses RFC 1483 Routed Static IP addresses will be provided by the service provider and are manually entered e Select Manual in the ADSL Modem Types of Access screen e Select Next The following screen is displayed 24 BT Versatility Broadband Module Broadband Module Plus Manual iT er DO er ure E OTI Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Select Next The following screen is displayed Broadband Module Basic Configuration Status System Backup Restore isc System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN ADSL Modem Types of Access There are five types of Internet Access available Choose a type that is suitable for your Internet connection from the options below 8 Tell me more about ADSL Modem settings PPPoA use this if you have a PPPoA DSL connection PPPoE use this if you have a PPPoE DSL connection e e DHCP use this if you have a DHCP DSL connection mn
49. ct Next The following screen is displayed Select Confirm Changes FICELLE UO BB LL ET HOS Broadband Module Basic Configuration Status System Backup Restore ak System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port Vatn The following screen is displayed 38 ISDN Confirm ISDN will be configured as a backup The phone number will be 923456789 The username will be username To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel BT Versatility Broadband Module Broadband Module Plus Manual ICEL BB LET E Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN 3 Enabled ISDN The ISDN settings control how the Broadband Module uses ISDN to connect to the Internet 8 Tell me more about the ISDN settings ISDN is currently configured as a backup The PPP Username is username The PPP Password is set The phone number is 923456789 Change the ISDN settings here This option is used where no broadband service is available and ISDN is always used to connect to the Internet When the browser is launched on any PC connected to the local LAN an ISDN call is automatically establis
50. cted Access WPA is used to prevent unauthorised access to your wireless network You can encrypt wireless network data transmissions using wireless network security Select an encryption option from the list below Tell me more about wireless network security C Off no encryption on the wireless network C 64bit encryption on the wireless network C 128bit encryption on the wireless network Wi Fi Protected Access WPA on the wireless network Cancel e Allow the WLAN to broadcast it s network name SSID e Do not allow the WLAN to broadcast it s network name SSID Recommended Four options are presented for security 1 Off e Select Next this takes you to Address Authentication page 50 2 64 bit encryption on the wireless network e Select Next The following screen is displayed Broadband Module ig i Broadband Module Basic Configuration Status System Backup Restore i System Restart Advanced Configuration Restart Required To implement your changes a restart is WLAN 64bit Network Key You must provide a 10 character hex network key for 64bit encryption A hex key is made of the letters A to F and numbers 0 to 9 3 Tell me more about Wireless network keys Key ecccccccce Cancel e Enter a 10 hexadecimal character key hexadecimal characters consist of the characters A F and the numbers O 9 Make a note of this key as it
51. ctes une E EE neces eonue E O EOE 86 RETTO OR AUT pui os iaseenae deu ese Ee MES Ee MU MIL M LL D E LE DE EAM LIE 86 opc m 88 PIPPEND Pasce T I P I I M 92 BT Versatility Broadband Module Broadband Module Plus Manual INTRODUCTION The BROADBAND MODULE and the BROADBAND MODULE PLUS are BT Versatility system modules that provide multi user high speed Internet access as well as VolP Voice over IP connectivity It also provides a LAN Local Area Network that allows users to network PCs and share printers and other resources within the office The BROADBAND MODULE has the following features Wide Area Networking Local Area Networking Wireless Local Area Networking Multi user Internet Access DSL Broadband ISDN Firewall VoIP Gateway supporting 2 IP trunks Management The BROADBAND MODULE PLUS has all the above features but includes a VoIP Gateway with 12 endpoints that can be configured as IP trunks IP extensions or any combination of both It also supports Unified Messaging BT Versatility Broadband Module Broadband Module Plus Manual CONNECTIONS The following connectors are located under the top cover ADSL RJ 11 10 Base T WAN ETH DMZ LAN Port 1 RJ 45 LAN Port 2 RJ 45 LAN Port 3 RJ 45 LAN Port 4 RJ 45 Port RJ 45 l1 3 4 X21 WAN INDICATORS There are six indicators LEDs on the MDF cover ADSL RESET BUTTON
52. d Module is 134 The YDB revision is 1 SETUP MENU The Setup menu contains the following LAN Gateway The LAN Gateway address is set by default to 192 168 1 1 The following procedure is used to change this setting e Select LAN Gateway in the Setup menu The following screen is displayed Broadband Module NT Add ressing Basic Configuration Status System Backup Restore System Restart Advanced Configuration Addressing controls the network address of the Broadband Module 3 Tell me more about the Broadband Module address settings Currently the address settings for the Broadband Module are IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Change the Broadband Module address settings here Setup LAN Gateway ADSL Modem ETH DMZ Port The current settings are shown e Select Change the Broadband Module address settings here The following screen is displayed 17 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband EE LAN Gateway Setup Basic Configuration Status You must provide an IP address for the Broadband Module and a local System Backup Restore subnet mask L System Restart 3 Tell me more about the IP addresses and subnet masks Advanced Configuration Broadband Module IP Address 182 168 1 le 1 Broadband Module Subnet Mask 255 255 255 Next gt Cancel Se
53. e System Restart Advanced Configuration Restart Required To implement your changes a restart is required Restart Setup LAN Gateway ADSL Modem ETH DMZ Port e Restart the module The ADSL Modem setup is now complete 22 ADSL Modem The ADSL Modem settings control how the Broadband Module connects to the Internet 8 Tell me more about the ADSL Modem settings ADSL Modem is currently configured as follows Internet Access is provided by DSL PPPoE with a YPI of 0 and a VCI of 38 The PPP Username is username The PPP Password is set Change the ADSL Modem settings here Your current MAC spoofing configuration is as follows MAC spoofing is disabled Enable or disable MAC Spoofing here BT Versatility Broadband Module Broadband Module Plus Manual 3 DHCP This option uses RFC 1483 Routed DHCP Dynamic Host Configuration Protocol is used to automatically obtain the IP addresses e Select DHCP from the ADSL Modem Types of Access screen Broadband Module A ADSL Modem Types of Access Basic Configuration Status System Backup Restore System Restart Advanced Configuration There are five types of Internet Access available Choose a type that is suitable for your Internet connection from the options below 8 Tell me more about ADSL Modem settings C PPPoA use this if you have a PPPoA DSL connection S PPPoE use this if you have a PPPoE D
54. e Disable Console Lagging Output ta Change Event Log Logging is enabled by default for Session Logging Blocking Logging and Intrusion Logging To disable all logging e Select Disable Security Logging Session Logging Blocking Logging and Intrusion Logging To disable any of the above e Select Disable e One of eight logging levels for reporting can be selected from the drop down menu Emergency Alert Critical Error Warning Notice 19 BT Versatility Broadband Module Broadband Module Plus Manual Informational Debug e The output can be directed to the Console or the Event Log IP ROUTES This allows static IP routes to be defined Existing routes are listed To change the parameters on an existing route e Select IP Routes in Advanced Configuration menu The following screen is displayed Broadband Module Broadband Module Basic Configuration ADSL Test Diagnostics Flash Update Reset to Defaults e Select Create new IP V4 route The following page is displayed Broadband Module Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN e Enter the following parameters Destination IP address Gateway IP address Netmask Advanced Configuration Edit Routes There are currently no Routes defi
55. eck Enable SSID Broadcast e Select Next The following screen is displayed 42 BT Versatility Broadband Module Broadband Module Plus Manual TA Broadband Module Basic Configuration Status 1 System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Select Allow any Wireless PCs to connect e Select Next The following screen is displayed RA Broadband Module Basic Configuration Status ME System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Select DMZ e Select Next The following screen is displayed ICEL EU BB LET HOS WLAN Address Authentication You can restrict which wireless PCs can connect to your device Select how you want to restrict PCs below 8 Tell me more about restricting wireless access Allow any wireless PCs to connect C Allow all wireless PCs to connect except those I specify C Only allow the wireless PCs I specify to connect Next gt Cancel Broadband Module WLAN Select Interface If you place the wireless network on the LAN your LAN PCs and y rai may be exposed to attack over the wireless network It is usually more secure to place the wireless network on the DMZ This restricts access from the wireless network to LAN devices but permits internet access from the wireles
56. ect Port Filters for an interface external internal external dmz dmz internal Firewall Port Filters external internal Source Destination pibsction Source Destination IP Port Port Address Address Protocol Min Max Min Max Inbound Outbound Any Any ICMP N A N A N A N A false true Delete si Soy TCP o 65535 O 65535 false true Delete Any Any UDP 0 65535 m 65535 false true Delete any Sny UDP 0 65535 5060 6000 true true Delete Add TCP or UDP Filter Add Raw IP Filter Return to Policy List This screen lists the filters currently in effect for that interface Adding Port Filters Select Add TCP or UDP Filter The following screen is displayed irewall Add TCP UDP Port Filter external internal Mask Mask 0 0 0 0 0 0 0 0 ree sj 0 65535 Destination Source Destination Direction Source address adres Protocol dm a s po Inbound Outbound l Range IP Address IP Address Start Range Start 0 0 0 0 0 0 0 0 End Allow gt Allow gt Apply Return to Filter List Return to Policy List Return to Interface List e Enter the following parameters 68 BT Versatility Broadband Module Broadband Module Plus Manual Source address Mask is always 255 255 255 255 P Destination address Mask is always 255 255 255 255 Protocol TCP or UDP Source port or range of ports associated w
57. ect a free endpoint and mE VolP Endpoint Type select UM Service You should fill out the following fields D Tall m mort about Voir Extension Type ITP extn 150 ITP Extension ITP Extn 161 ITP Extension ITP Extn 152 ITP Extension 7 ITP Extn 153 ITF Extension IP Trunk 5 Trunk IP Trunk 6 Tank Endpoint 7 Endpaint amp Endpoint 9 Endpoint 10 Endpoint 11 Endpoint 12 Select Next gt Tier D ESTIS DT miler ME Select Confirm Changes Broadband Hadube VoIP Co nfirm The endpoint settings will ba Restart the module Type Endpoint 1 ITP Extn Endpoint 2 ITP Extn Endpoint 3 ITP Extn Endpoint 4 ITP Estr Endigaint 5 Trunk Endgaint amp Trunk Endpoint 7 UM Biervica Endpoint amp Inactive Endgaini 9 Inactive Endigaint 10 Inactive Endpoint 11 Inactive Endpaint 17 Inactive To confirm this setting click on the Confirm Changes button below IF you do not with to apply this setting click on the Cancel button Confirm Changes Cancel 15 BT Versatility Broadband Module Broadband Module Plus Manual PROGRAMMING All BROADBAND MODULE AND BROADBAND MODULE PLUS parameters can be programmed using BT Versatility Wizard or via a browser on any PC connected to the LAN The Welcome screen and all subsequent screens presented are identical for both methods of access Programming from BT Versatility Wizard Connect the PC with BT Versatility Wizard directly to the V 24 interface on t
58. elect Confirm Changes e Restart the module 2 Enable e Select Next This takes you through the procedure as described in First Time Settings 54 STATUS This displays the current status of the main system parameters BT Versatility Broadband Module Broadband Module Plus Manual Internet Module Internet Status WAN Status DMZ Status LAN Status VoIP Status Routing Table Connected interact IP Addrass Subnet Mask Goleray Primary DNA Secondary DNS IP Assignment IP Address Subnet Mask IP Address Subnet Mask MAC Address DHCP Server User Domain SIP Proxy Destination Setmask 192 189 1 0 255 285 255 0 D 0 0 0 iplan 182 168 0 0 255 255 255 0 D 0 0 0 ipdmz 127 0 0 0 255 0 0 0 Ha ADSL Mech 0 0 0 0 0 0 0 0 net currently get Hot currently set not currently get Dynamic Ao 192 168 0 1 255 255 255 0 192 168 1 1 2E5255 255 0 n a0 7D 00 42 82 Yas bbv sipsernice nat bt com bby sipservice nat bt com 5DGO Gateway Interface 0 0 0 0 loopback Hardware Status Up Timws 20 23 08 Hardware Revision cC Firmmant Revision O67 55 BT Versatility Broadband Module Broadband Module Plus Manual SYSTEM BACKUP RESTORE This allows you to backup the module settings to your PC and also to restore the settings e Select System Backup Restore The following page is displayed Backup Configuration e Select Backup System Backu
59. ement your changes a restart is required Add an address here Next Cancel e Select add an address here The following screen is displayed TOT Ce Lr UT B OL LU S Te WLAN Address Authentication Basic Configuration Status System Backup Restore ii System Restart Advanced Configuration Enter the MAC address to add below 8 Tell me more about restricting wireless access MAC address 00 10 38 03 2c og Cancel Restart Required AA To implement your e Enter the MAC address of the PCs to be allowed to connect to the wireless network e Select Next The following screen is displayed TOT C T HT BB LL Te V S peas ete WLAN Address Authentication Basic Configuration Status System Backup Restore i System Restart gt Advanced Configuration You can configure the list of addresses to allow access to your device below 8 Tell me more about restricting wireless access 00 10 36 03 2C 06 Restart Required To implement your changes a restart is required Add an address here Remove an address here i Cancel Add an address here takes you back to the previous screen to enter another MAC address Remove an address here takes you to the following screen 51 BT Versatility Broadband Module Broadband Module Plus Manual TOT C eT LoT BB LL Te LV S pie WLAN Address Authentication
60. epair Other Places Bridge Connections E Control Panel Create Shortcut My Network Places Delete L My Documents Rename iY My Computer Properties axl O Select Internet Protocol TCP IP click General Authentication Advanced Connect using P ro p e rti es 33 Intel 8255x based Fast Ethernet This connection uses the following items Client for Microsoft Networks i Check Point SecuRemote i QoS Packet Scheduler Internet Protocol TCP IP Install Uninstall Properties Description Transmission Control Protocol Intermet Protocol The default wide area network protocol that provides communication across diverse interconnected networks E KI K V Show icon in notification area when connected v Notify me when this connection has limited or no connectivity OK Cancel ETET General Aemate Coeigquation You can gel IP antings assigned automatically ii your neuk supports Select Obtain an IP address automatically it carebit Ohare oreet ak youe ew sin fe Obtain DNS server address automatically click OK nan es acai C Uge the folowing IP addet z JP adie E Ofen DNS server ende anbomalacalte C Use the folcwang DNS server ed rerpes Parad DHG sene SG Hande DNE genes BIS WE EF The PC is now set up to automatically obtain an IP address SETTING UP THE BROWSER o0 Click Tools Internet Options 2 Select Co
61. er Number of Retries IB Retry Interval 30 seconds Initial Periad 3 minutes Recurring Period IT minutes Idle Timer 30 seconds Maximum Calls day 0 Auto Recovery On Enabled f Disabled Auto Recovery Timer 30 minutes Change Reset If the ISP provides a secondary telephone number for Internet access in case the primary number is unavailable it can be entered here If the first attempt to establish an ISDN connection is unsuccessful the module automatically redials the number The user configures the number of times the number is redialled within the range 1 255 The default setting is 50 retries The number of retries applies first to the main telephone number and then to the backup telephone number if it is enabled lf a connection cannot be established on the backup number after the last retry no further attempt is made to establish a connection No limit is placed on the number of retries if O zero is specified as the number of retries This defines the time interval between retry attempts and is programmable within the range 5 60 seconds The default setting is 10 seconds During an ISDN call a timer is set to disconnect the call if no data Is sent or received for a period of time Three timers are used The Initial Period defines the period from the start of the call to the end of the initial billing period This can be set by the user to the initial billing period of the ISDN call This information is avail
62. he PBX and launch BT Versatility Wizard e BT Versatility User Wizard 3 1 File System Extensions Lines Internet Module Hotel Ovida Setup Help Disconnected VersatilityPABXInstance xml Idle e Select Connect e Onthe pop up menu select the COM port and speed The default setting for the speed is 115 200 bps This can be changed if required e Select Connect e When the connection is established select Broadband Module on the main menu CHAT Versatility Weer Wizard 3 1 Coannecied via V 74 ariani ADI tance xml ldi amp 16 BT Versatility Broadband Module Broadband Module Plus Manual The Basic Configuration screen is displayed BASIC CONFIGURATION The Basic Configuration screen shows the current Internet access settings as well as the hardware and firmware versions Broadband Module Tor Basic Configuration Basic Configuration Status This page shows general status information about the Broadband Mod System Backup Restore 8 Tell me more about the status information a System Restart Advanced Configuration Internet Access settings Setu xm Internet Access is provided by the ADSL Modem LAN Gateway ADSL Modem The default gateway is not currently set ETH DMZ Port VoIP No name DNS servers have been configured ISDM WLAN About the Broadband Module The hardware revision for the Broadband Module is C The firmware version for the Broadban
63. he following screen is displayed TOT e Le UT B OL LU S WLAN Channel Selection Basic Configuration Status System Backup Restore i System Restart Advanced Configuration You may either choose a channel yourself or allow the Broadband Module to automatically select the best channel 3 Tell me more about wireless channels Allow the Broadband Module to select channel C Select a channel manually Next gt Cancel LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Select Allow the Broadband Module to select a channel e Select Next The following screen is displayed iT OT Ce Le UT B LES Te LU LES VIN TEGERE WLAN Security Basic Configuration Status It is highly recommended that Wi Fi Protected Access WPA is used to prevent unauthorised access to your wireless network System Backup Restore System Restart Advanced Configuration ER n You can encrypt wireless network data transmissions using wireless network security Select an encryption option from the list below Setup 8 Tell me more about wireless network security LAN Gateway Off no encryption on the wireless network ADSL Modem s C 64bit encryption on the wireless network ETH DMZ Port VoIP C 128bit encryption on the wireless network ISDN WIAN C Wi Fi Protected Access WPA on the wireless network gere Enable SSID Broadcast iw Cancel e Select Off e Ch
64. hed to connect to the Internet Broadband Module es Broadband Module Basic Configuration Status System Backup Restore D system Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAM e Select Enabled e Select Next The following screen is displayed ISDN Mode Choose an ISDN mode that is suitable for your Internet connection from the options below 3 Tell me more about ISDN settings C Disabled use this if you do not want to use ISDN for Internet access Backup use this if you want the Broadband Module to use ISDN for backup Internet Access when ADSL is unavailable Cancel Broadband Module Broadband Module Basic Configuration Status System Backup Restore m System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN ISDN Settings In order to use an ISDN connection to the Internet you must supply a username password and phone number to logon to your Internet Service Provider ISP Your ISP should provide you with these details when you sign up for their service 3 Tell me more about the ISDN settings Phone Number 823456789 PPP Username username PPP Password eeeeee Retype the PPP Password eeeeee Next gt Cancel e Enter the external call access digit default is 9 followed by the Phone Number e Enter the Username and Passwo
65. here are five types of Internet amp ccess available Choose a type that is suitable for your Internet connection from the options below 8 Tell me more about ADSL Modem settings C PPPoA use this if you have a PPPoA DSL connection PPPoE use this if vou have a PPPoE DSL connection Setup DHCP use this if you have a DHCP DSL connection LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDM WLAN C C Manual use this to configure your connection s gateway and DNS servers directly Cancel e Select Next The following screen is displayed Broadband Module Broadband we ADSL Modem PPPoE Basic Configuration Status System Backup Restore S System Restart Advanced Configuration In order to use a PPPoE connection to the Internet you must supply a username and password to logon to your Internet Service Provider ISP Your ISP should provide you with a username and password when you sign up for their service 3 Tell me more about the PPP username and password Setup PPP Username username LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN PPP Password eeeesee Retype the PPP Password eeeeees Next Cancel e Enter a Username and Password Retype the Password e Select Next The following screen is displayed 21 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband Module Basic C
66. identifies the protocol carried in the IP packet Host Validators are used to block all traffic from a specific host The parameter used to specify this filter are an IP address or range of addresses Note that if invalid filter entries are added an error message will be displayed when the configuration is saved Policies Triggers Intrusion Detection Logging Security Policy Configuration Q Security Trigger Configuration Q Configure Intrusion Detection O Configure Security Logging 9 e Select Security Policy Configuration The following screen is displayed 67 BT Versatility Broadband Module Broadband Module Plus Manual By 7 Broadband Module Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN TOT Ce Lr UT B LES Te LU S Security Policy Configuration Current Security Policies Interface Interface Type 1 Type 2 Validators Policy Configuration i i Only listed Port Host orroma Hncema hosts blocked Filters validators t Only listed Port Host eae us hosts blocked Filters Validators QO d int Only listed Port Host ie eres hosts blocked Eilters Validators The following screen is displayed for the interface selected Return to Interface List y Sel
67. inations of ports and protocols are possible Port Protocol Port Protocol ADSL Modem PPPoE PPPoA and ETH DMZ BEEN For example the ADSL Modem could be used to connect to the Internet for web browsing and the ETH DMZ port could be connected to a gateway into a private wide area network FIREWALL The module is equipped with a firewall that has the following features Stateful Inspection Packet Filter Definition Network Address Translation Intrusion Detection Security Logging VOIP The BROADBAND MODULE is equipped with a VoIP gateway with the following features e 2endpoints which support IP trunks e Proxy server registration e Codecs G 711 G 729 e Quality of Service The BROADBAND MODULE PLUS is equipped with a VoIP gateway with the following features e 12 endpoints which support trunks extensions unified messaging or any combination of all three e Proxy server registration e Codecs G 711 G 729 e Quality of Service BANDWIDTH REQUIREMENTS The BROADBAND MODULE and BROADBAND MODULE PLUS support two different codecs each with different bandwidth requirements In addition to the bandwidth used by a codec there is also an overhead imposed by the various protocols used in transporting the IP packets as well as signalling When this is taken into account the actual bandwidth required for each codec increases significantly In order to ensure good voice quality it is recommended that the following bandwidth is
68. ing chek on the Cancel button Condrm Changes Cancel The IP Extension programming is now completed The following extension numbers are assigned to each endpoint These are the default settings The extension numbers can be changed in the PBX Flexible Numbering option Extension Endpoint 150 1 151 152 153 154 155 156 157 158 159 160 161 mo O N WD oO KR Ct N EB e e N e O 14 BT Versatility Broadband Module Broadband Module Plus Manual SETTING UP UM SERVICE Unified Messaging provides email notification of voicemail messages left in the PBX voicemail system One IP endpoint must be permanently assigned to UM Select VoIP from the Setup menu Broadband Module Select Change VolP Endpoint CEDE d Module VoIP types here Setting up valIP for the Broadband Module allows you to route telephony calls over a data network E Toll mar more about vote Your current Yol settings are ITP Extn 150 G711 G729 OO 10 06 04 65 F A ITP Extn 151 G711 G729 nn 10 36 04 65 FB ITF Extn 152 GI11 G725 OO EEN EE b ITP Extn 153 711 0729 0 TEETE mE a IP Trunk 5 G711 0729 05600490010 DP Trunk amp G711 G729 OS5S600400011 Endpoint 7 6C711 C7290 Mot Conligured Endpoint amp GI11 G6725 Pont Canfiurid Endpoint amp 711 0729 Mot Canfiqured Endpoint 10 G711 G729 Not Configured Endpoint 11 6G711 G729 Not Configured Endpoint 12 C711 6720 Mot Conligured C Wigie En i LE C gl i L Broadband Module Sel
69. it 7 Inactive Endpoint amp Lranct ivo Endpaint Inactive Endpoint 10 Inactive Endpoint 11 Inactive Endpant 12 Inactive To confirm thes setting click on the Confim changes button below Tf you d not wish to apply the setting click on the Cancel button Car rm Changes Cancel Broadband Module VoIP Endpoint Authentication You should fill cut tho folowing Fields g Tell ma mora about VoIP Username Password E C Address Endpoint 1 m Endpoint 2 ITP Extn 152 IT Extn 153 ITP Extn 154 ITP Extn 155 Endpoint 7 Endpoint amp Endpoint 8 En paint 10 Endpoint 11 En paint 12 News Cancel IIT 13 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Q select Confirm Changes LITLZZ VoIP Confirm Wake Configur at oon ETT The endpoint settings will be LO pple hek Rector Restart the module system Restart Username MAC Advanced Configuration Endpoint 1 Mot Configured Endpoint 2 Mot Configured Restart Required ITP Exin 152 D010 6 0200500 To implanent your ITP Exin 153 no 10 36 02 00 00 changes a restart iz ITP Extri 154 OO LO 6 0S 500500 required TTP Extr 155 UD UO se E Endpoint 7 M t Configured Endpoint amp Not Configured Endpoint 9 Mot Configured Endport 10 Motl Conligured Endporit 11 Mot Cuonfiqunecd Endpoint 12 Mot Configured Tao confirm thes setting click on th Ganfirm Changes button below Tf you do not wish to agply thee sett
70. ith source IP address Destination port or range of ports associated with destination IP address Direction Inbound or Outbound e Select Apply e Save the new configuration e Restart the module Adding Raw IP Filters Filters based on IP address and protocol only can be added to the security level displayed e Select Add Raw Filter The following screen is displayed Firewall Add TCP UDP Port Filter external internal Source address IP Address 0 0 0 0 Mask 0 0 0 0 0 0 0 0 Apply Return to Filter List Return to Policy List Return to Interface List Enter the following parameters IP Source address and Subnet Mask IP Destination address and Subnet Mask IP Protocol Direction Inbound or Outbound e Select Apply e Save the new configuration e Restart the module Host Validators Traffic to or from specific hosts can be blocked by the firewall Destination Direction port Inbound Outbound Range Start End Db Allow z Allow z 65535 69 BT Versatility Broadband Module Broadband Module Plus Manual PENT Broadband Module Basic Configuration Flash Update Reset to Defaults Advanced Configuration L ADSL Test Diagnostics Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN 2T eT eer Ie M O DH LS Security Policy Configuration Current Security Policies Inte
71. itially installed the codec will be set by the BT engineer Advanced VolP Settings These parameters are pre configured and should not be changed Unified Messaging Settings These parameters are pre configured for use with BT e mail services If you wish to use a different e mail service provider carry out the following Go to the main VoIP screen scroll down and select the link Change Unified Communications Settings here Broadband Module Teo VolP Unified Communication Basic Configuration Status System Backup Restore iii System Restart Advanced Configuration Q Tell me more about Unified Communication The SMTP and IMAP Clients are currently configured as follows Server Name Port Setup SMTP smtp btconnect com 25 LAN Gateway IMAP imap4 btconnect com 143 ADSL Modem ETH DMZ Port VoIP ISDM WLAN Change the Unified Communication address settings here Select the link Change the Unified Communications address settings here Broadband Module TTE Unified Communication Address Setup Basic Configuration Status Server Name Port System Backup Restore z 1 BB system Restart SMTP smtp other com 25 4 Advanced Configuration IMAP imap 4 other com 1 43 Setup Cancel LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDM WLAN Enter the following SMTP server name and port number IMAP server name and port number Your e
72. itor how your DSL connection is performing by looking at the DSL Status page Perform ADSL Test e Select Perform ADSL Test The tests are performed and the results are displayed complete Failed Physical connection WAN port ADSL line connecting disconnected handshaking 83 BT Versatility Broadband Module Broadband Module Plus Manual Aborted User s ppp Configuration Incorrect username or connection changed during test password Failed User s ppp ppp connection Incorrect protocol connection establish Type of Access Incorrect VPI or VCI DSL Status e Select DSL Status on the ADSL Test page Operational mode Inactive State HandShake Trained transmit bit rate kbps Trained receive bit rate kbps Upstream power 0 0 dB Local Fast channel FEC error count Local Interleaved channel FEC error count Lacal Fast channel CRC Oo Local Interleaved CRC Local line attenuation 0 0 dB Local signal to noise margin 0 0 dB Local LOS Lacal SEF Oo Remote Fast channel FEC error count Remote Interleaved channel FEC error count O Remote Fast channel CRC Remote Interleaved CRC Remote line attenuation 0 0 dB Remote signal to noise margin dB Remate LOS oO Remote SEF o This page displays a range of DSL parameters indicating line speed and quality Parameter Description Operational Mode Inactive the line is disconnected or the DSL modem is negotiation with the DSLAM G DMT or 11 413 i
73. layed Broadband Module EE WLAN Address Authentication Basic Configuration Status System Backup Restore System Restart Advanced Configuration You can configure the list of addresses to deny access to your device below 8 Tell me more about restricting wireless access No addresses have been set Restart Required Add an address here Next Cancel To implement your changes a restart is required e Select Add an address here The following screen is displayed Broadband Module REEN WLAN Address Authentication Basic Configuration Status System Backup Restore m System Restart Advanced Configuration Enter the MAC address to add below Q Tell me mare about restricting wireless access MAC address DO 10 36 03 2C 07 Cancel Restart Required AV To implement vour e Enter the MAC address of the PC which is to be excluded from the wireless network e Select Next The following screen is displayed TOT C E HT BB LL Te V S Broadband Module WLAN Address Authentication Basic Configuration Status System Backup Restore System Restart Advanced Configuration You can configure the list of addresses to deny access to your device below 8 Tell me more about restricting wireless access grgvsmmsr scm Add an address here Remove an address here Next Cancel To implement yo
74. le Choose a type that is suitable for your Internet connection from the options below Q Tell me more about ETH DMZ Port settings C IP Gateway use this if your internet connection is provided by an setup external router or LAN LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN C DMZ use this if your internet access is provided on the DSL port and you are using the ETH DMZ Port to host a DMZ Cancel e Select PPPoE from the ETH DMZ Port Mode screen e Select Next The following screen is displayed 2 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module EEEE ETH DMZ Port PPPoE Basic Configuration Status System Backup Restore System Restart Advanced Configuration In order to use a PPPoE connection to the Internet you must supply a username and password to logon to your Internet Service Provider ISP Your ISP should provide you with a username and password when you sign up for their service 8 Tell me more about the PPPoE username and password PPP Username usemame Setup PPP Password eeeeeee LAM Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAM Retype the PPP Password eseese Cancel e Enter a Username and Password Retype the Password e Select Next The following screen is displayed
75. lished before VoIP can be programmed Refer to the VoIP section page 6 to find out how many IP trunks can be supported on your broadband connection When you subscribe to the BT Broadband Voice service you will be given a URL to link to and a username and password Connect to the URL from any PC on the LAN and enter the username and password The VolP trunks will then be automatically configured To verify that the trunks have registered with the BT Broadband Voice service e Select Status from the main menu scroll down to VoIP and verify that each trunk has registered as indicated by V SETTING UP IP EXTENSIONS The BROADBAND MODULE PLUS supports up to twelve IP endpoints which can be configured as either trunks extensions or a combination of both Note that when Unified Messaging Service is required one endpoint must be permanently assigned to it V I P Featurephones must be used as local or remote extensions Note that other manufacturers IP phones will not work with the system Refer to the V IP Featurephone Quick Reference User Guide for setting up and connecting the phone Select VoIP from the Setup menu 12 Select Change VolP Endpoint types here Select ITP Extension for each endpoint to be configured as an extension Select Next gt Select Confirm Changes O Enter the Password and MAC address for each extension The MAC address is printed on a label on the base of the V IP Featurephone
76. mail service provider will provide the above information If synchronization is not provided by your service provider leave the IMAP server name and port number at their default settings these fields must not be left blank Select Next gt 36 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband AeIE Unified Communication Confirm Basic Configuration Status System Backup Restore ia System Restart The SMTP Server settings will be smtp other com 25 The IMAP Server settings will be imap4 other com 143 Advanced Configuration To confirm this setting click on the Confirm Changes button below If you do not wish to apply this setting click on the Cancel button LAN Gateway Confirm Changes Cancel ADSL Modem ETH DMZ Port VoIP ISDN WLAN Select Confirm Changes Broadband Module E VolP Unified Communication Basic Configuration Status System Backup Restore System Restart Q Tell me more about Unified Communication The SMTP and IMAP Clients are currently configured as follows Advanced Configuration Server Name Port Setup SMTP smtp other com 25 LAN Gateway IMAP imap4 other com 143 ADSL Modem ETH DMZ Port Change the Unified Communication address settings here VoIP ISDN WLAN The new settings are displayed ISDN Where the PBX is equipped with ISDN line s ISDN can be used to automatically back up the on board ADSL modem in the eve
77. mat you must supply a usemame and password to lagen to your Intemet Service Provider TER Your ISP should provide you with a usemame and password when you sign up For their service D Tell ime m r PPP Lstrmamae PPP Password Retype the PPP Password Heo gt Cancel ADSL Modem Manual VPI and VC Setup The Broadband Module rieedz ta know which YPL and vcr it should use far internet Access Enter the VPI and Wel values that your SP has provided in the boeas below ae Tall me mor af ve 0 c1 30 Mett Cancel Broadband Module Broadband Module fare Corfapr ation Satus T System Bacup Restore System Bm wt Advanced Configurelon ADSL Modem Confirm Internet Access will be provided by PPPoA The VPI will be 0 and the VCI wil be 38 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings cick on the Cancal button Confirm Changes Cancel 11 BT Versatility Broadband Module Broadband Module Plus Manual 9 The new settings are displayed Broadband Module Restart the module ADSL Modem Ta implement your charges a reitartm reogured change the ADSL Modem Settings hane The ADSL setup is now complete SETTING UP IP TRUNKS The following procedure is used to set up the BROADBAND MODULE and the BROADBAND MODULE PLUS to operate with the BT Broadband Voice service A broadband connection must first be estab
78. must be entered into every PC that connects to the WLAN e Select Next this takes you to Address Authentication page 48 3 128 bit encryption on the wireless network e Select Next The following screen is displayed 48 BT Versatility Broadband Module Broadband Module Plus Manual TOT C eT LoT BB LL Te LV S Broadband Module Basic Configuration Status System Backup Restore E System Restart Advanced Configuration Restart Required To implement your changes a restart is WLAN 128bit Network Key You must provide a 26 character hex network key for 128bit encryption A hex key is made of the letters A to F and numbers 0 to 9 3 Tell me more about Wireless network keys Key 0esesesesecesceseseses Cancel e Enter a 26 character hexadecimal key hexadecimal characters consist of the characters A F and the numbers 0 9 Make a note of this key as must be entered into every PC that connects to the WLAN e Select Next this takes you to Address Authentication page 48 4 Wi Fi Protected Access WPA on the wireless network Recommended e Select Next The following screen is displayed TOT C T HT BB LL oT UI Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Restart Required To implement your changes a restart is required WLAN Wi Fi Protected Access You must p
79. nd is available to engineering support personnel only RESET TO DEFAULTS This resets the module to the factory default settings Select Reset to Defaults from the Advanced Configuration menu The following screen is displayed Internet Module Internet Module Reset to Defaults Resetting Internat Module will change its settings to factory defaults This will overwrite any changes that you have previausty made to the device Settings CF Tell ma mare about resetting to defaults Peset ng the devece to factory defaults can not be undone To reset Internet Module tek the Conlin box and then cheek on Reset bp Daelaults Li tentfire Piesetto Dudas 86 BT Versatility Broadband Module Broadband Module Plus Manual Check the Confirm box Select Reset to Defaults The default settings are restored 87 BT Versatility Broadband Module Broadband Module Plus Manual APPENDIX A Setting up wireless networking on a PC using the recommended settings in WLAN setup Enter the settings used in the initial WLAN setup page 44 in the table below Refer to this table when setting up PCs to connect to the WLAN Ce 0 00000 a e ELT NENNEN ELT NNNM ELT NENNEN ELT C NENNEN ELT NENNEN Wem 000 wos O Wem 000 This procedure describes setting up WPA security on a PC with Windows XP For other operating systems please consult your PC user manual Note that some older wireless LAN adapters do not su
80. ndicates the DSL standard that has been negotiated with the DSLAM Showtime the line is synchronised and the ADSL connection is successfully established Training the ADSL modem is negotiating line speed with the DSLAM Handshake the handshaking procedure is taking place to determine the nature and capabilities of the endpoints Trained transmit bit rate The upstream line speed Trained transmit bit rate The downstream line speed 84 Upstream power Local Remote fast channel FEC error count Local Remote interleaved channel FEC error count Local Remote fast channel CRC Local Remote interleaved channel CRC Local Remote line attenuation Local Remote signal to noise margin Local Remote LOS Local Remote SEF DIAGNOSTICS BT Versatility Broadband Module Broadband Module Plus Manual The output power of the ADSL modem The fast channel Forward Error Correction error count measured at the near far end The interleaved channel Forward Error Correction error count measured at the near far end The fast channel Cyclic Redundancy Check error count measured at the near far end The interleaved channel Cyclic Redundancy Check error count measured at the near far end The line loss measured at the near far end The signal to noise ratio measured at the near far end The number of occurrences of Loss of Signal at the near far end The number of Severely Errored Frames received at the near far end This i
81. ned Create new Ip V4Route O Help Broadband Module Create Ip V4Route Name Value Destination 0 0 0 0 Gateway Netmask 0 0 0 0 Cost fi Interface none Advertise false ok Reset Cancel Cost this sets the number of hops counted as the cost of the route Interface choose from the following ipwan ipdmz iplan None Advertise true or false e Select OK The list of routes is displayed again 76 BT Versatility Broadband Module Broadband Module Plus Manual DHCP SERVER e Select DHCP Server in the Advanced Configuration menu The DHCP Server is displayed Enable Disable The DHCP server is enabled by default Broadband Module TEETE Module DHCP Server Basic Configuration __ Advanced Configuration This page allows creation of DHCP server subnets and DHCP server fixed L ADSL Test host IP MAC mappings You may also enable and disable the DHCP server Diagnostics from here Flash Update Reset to Defaults The DHCP server is currently enabled Disable Advanced Setup Admin Accounts e Select Disable to turn off the DHCP server DHCP Server Interfaces By default the DHCP server operates on the iplan and ipdmz interfaces There is an option to delete DHCP on each interface AULT ALLUUTILS Firewall amp Security IP Routes DHCP server interfaces DHCP Server Advanced ISDN Use this section to edit the list of IP interfaces that the
82. nexant temp m Name InternetModule icf Custom Callouts Training File Download s Documents and Settings Urmet Type Unknown File Type 30 4 KB E EPOAgent vor From 192 168 1 1 i386 CQ VoIP Testing italy windows E LAKE WLAN Save Cancel Lotus O xXtenNetworksInc D ovida Software InternetModule icf While files from the Internet can be useful some files can potentially m harm your computer If you do not trust the source do not save this File name IntemetModule e file What s the risk My Network Save as type icf Document e Select Save e Select the folder where the file is to be saved e Save the file Restore Configuration e Browse for the configuration file Choose file Look in lt Local Disk C odi Gm 73 BT PATHWAY Owners Manual dS winPcap 3 1 beta4 ry BBM Firmware 064 Report Log My Recent sEjcamtasiaf Documents E comLoG B ethereal setup 0 10 11 EM coogleEarth InternetModule icf v iTunesSetup E Resip rrrrrrrr tic sambar62p S setup sigma Router Specification Qi strauss thus spake zarathustra voip test1 lt Jill Desktop E My Network File name lIntemetM odule m Places Files of type All Files m e Select Open Broadband Module System Backup Restore Basic Configuration Status This page allows you to backup the configuration settings to your System Backup Restore computer or rest
83. nfiguration Status System Backup Restore RS System Restart gt Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP maa The following screen is displayed ISDN Mode Choose an ISDN mode that is suitable for your Internet connection from the options below 8 Tell me more about ISDN settings C Disabled use this if you do not want to use ISDN for Internet access Backup use this if you want the Broadband Module to use ISDN for backup Internet Access when ADSL is unavailable Enabled use this if you want to always use ISDN for Internet Access Next Cancel ICEL U BB LET HOS Broadband Module Basic Configuration Status System Backup Restore Lu System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN ISDN Settings In order to use an ISDN connection to the Internet you must supply a username password and phone number to logon to your Internet Service Provider ISP Your ISP should provide you with these details when you sign up for their service 8 Tell me more about the ISDN settings Phone Number 823456789 PPP Username username PPP Password eeeeee Retype the PPP Password cocoes Next gt Cancel Enter the external line access digit default is 9 followed by the Phone Number Enter the Username and Password Retype the Password Sele
84. nges a restart is required Restart Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDM WLAN Enable Silence Suppression This applies to IP trunks only is disabled by default and should not be changed Enable RFC2833 VoIP Endpoint Additional Options You should fill out the following fields Tell me more about VoIP Enable Silence IP Trunk 1 IP Trunk 2 Endpoint 3 Endpoint 4 Endpoint 5 Endpoint 6 Endpoint 7 Endpoint 8 Endpoint 9 Endpoint 10 Endpoint 11 Endpoint 12 Next Cancel Suppression m E NS B B E M E EH D E iil Enable RFC2833 Codecs B G711 G728 gt 87118729 gt 6711 6729 G711 G729 gt G711 8729 a711 4729 gt a711 4729 G711 G729 gt a711 8729 gt 87118729 gt q711 6729 gt 6711 6729 z E m Bi Bi O mi Hi Bi Bi M On the BROADBAND MODULE this applies only to IP trunks is disabled by default and should not be changed On the BROADBAND MODULE PLUS it will be automativally enabled by the BBV Service on registration and should not be changed Codecs On the BROADBAND MODULE G 711 will be automatically enabled by the BBV Service on registration and should not be changed 35 BT Versatility Broadband Module Broadband Module Plus Manual On the BROADBAND MODULE PLUS G 729 will be automatically enabled by the BBV Service on registration and should not be changed For IP extensions when the V IP Featurephone is in
85. nnections click LAN Settings Uncheck Use a proxy server for your LAN click OK The browser is now set up BT Versatility Broadband Module Broadband Module Plus Manual 3i LAKE Intranet Microsoft Internet Explorer File Edit View Favorites WEWEEE Help 3 Mail and News e 2 Oo v v x gt e S Back Forward Stop Pop up Blocker Favorites History Mail Print Edit Manage Add ons Synchronize Windows Update Address Links 8 Aesthetics of the Prime Sequ LAKE d s Most Comprehensive Motoring Site Currency Internet Options 9 popes unm D F Bi a T gmas LAKE Group Info Doing the Business Deres Security Privacy Content Connectiont Program Advanced 5 Tosu an Intemel connecter click T 9i em mm EE Chocia Dehri if pou need bo conbguare amp pr ey Settings bene bea correction ime TE Newer dad connection T Dial shanini a reiber rk connection it not peint T7 Pleni cial any sd mult conimeection Cunendelmdc None LAN Sergi do nob apok lo daup connectors LAN Senna Len 7 a BT Versatility Broadband Module Broadband Module Plus Manual CONNECTING TO THE PROGRAMMING INTERFACE In order to provide maximum security PCs connected to the WLAN are not allowed to program the module via the web interface If programming from a wireless network PC is required the WLA
86. nt of line failure In the case where no broadband service is available ISDN can be used for Internet access The default setting is that ISDN is disabled Obtain the following information from your Internet Service Provider Phone number to connect to the ISP Username Password e Select ISDN from the Setup menu The following screen is displayed Broadband Module AA ISDN Basic Configuration Status The ISDN settings control how the Broadband Module uses ISDN to connect to the Internet System Backup Restore E Q Tell me more about the ISDN settings System Restart Advanced Configuration ISDN is currently disabled Setup LAN Gateway ADSL Modem CTU Div Change the ISDN settings here e Select Change the ISDN settings here Three options are presented for using ISDN 37 BT Versatility Broadband Module Broadband Module Plus Manual 1 Disabled With this option ISDN is never used to establish an Internet connection This is the default setting 2 Backup When this option is enabled ISDN is used to automatically backup the on board ADSL modem in the event of line failure When a line failure is detected ISDN will wait 60 seconds before backing up ADSL When the ADSL line is restored the ISDN call will be automatically disconnected and browsing resumed over ADSL Select Backup Select Next TOT Ce EU Te B Li EST TIE Broadband Module Basic Co
87. ntly O wireless PCs connected View details of connected wireless PCs e Select Enable or disable the wireless network here The following screen is displayed Broadband Module TET Module WLAN Enable Disable Basic Configuration Status Enabling wireless networking will allow PCs with wireless network System Backup Restore capabilities to connect to the Internet through the Broadband Module System Restart Q Tell me more about the wireless networks Advanced Configuration Select whether you want wireless PCs to connect to your device Setup C Disable wireless PCs will not be able to connect to your device LAN Gateway ADSL Modem Enable Wireless PCs will be able to connect to your device r M S He ETH DMZ Port VoIP Cancel ISDN WLAN e Select Enable e Select Next 41 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is displayed Broadband Module acus TERETE WLAN Basic Basic Configuration Status Before a wireless network can operate you need to provide a name System Backup Restore SSID for the network System Restart Network Name SSID PRISM_01_1f_54 Advanced Configuration Next Cancel Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Note the SSID e Select Next T
88. oadband Module Broadband Module Plus Manual External External DMZ Low Security Level lt gt lt gt lt gt from any source IP io or any Internal DMZ Internal inserter On e on w on pF T T T TY T Aw ree 9 655 F T E T E T HIP TCP 80 F T T T Tj T Tent TCP 235 F T T T TO OT SMP _ TCP 25 OF CTT CT T FrFy rT RMP TCP 50 OF OT TO FrFyj rT rTj Fr po TCP 350 FT FT FT TTF POP TCP 110 FO TO TO TO OF oT ISAKMP UDP 50 F TO FO TO TO OF SSL TCP 443 OF CT CF CT CT OF Kerberos TCP 88 F T F TO TO OF Kerberos UDP 88 F T F TO T OF DNS UDP 5 FE TT TT TTT TT TT Changing the security level deletes the previous security level and any filters set and replaces them with the new configuration To change the security level IP Routes DHCP Server Security Level Advanced ISDN Security Level high M Change Level none high Security aces e Select the required level from the drop down menu e Select Change Level To add a filter See section on Security Policy Configuration see page 64 Security Interfaces Three security interfaces are defined by default ipwan external to internal ipwan external to dmz 64 BT Versatility Broadband Module Broadband Module Plus Manual ipdmz dmz to internal NAT Network Address Translation NA
89. of the following modes Your service provider will advise you on the mode to be selected LLC Bridged LLC Routed VCMux Bridged VCMux Routed Enable Link State Monitoring should be ON e Select Next 25 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is displayed VPI VCI VPI VCI Virtual Path Identifier Virtual Circuit Identifier specify the ATM connection between the ADSL modem and the service provider The VPI range is 0 4095 The VCI range is O 65535 The default values are 0 38 Broadband Module Broadband Module ADSL Modem Manual VPI and VCI Setup Basic Configuration Status System Backup Restore System Restart The Broadband Module needs to know which VPI and VCI it should use for Internet Access Enter the VPI and VCI values that your ISP has provided in the boxes below Q Tell me more about choosing YPI and VCI values Advanced Configuration VPI 0 VCI 38 Next gt Cancel LAN Gateway ADSL Modem ETH DMZ Port VoIP Enter the VPI and VCI values if they are different from the default values Select Next The following screen is displayed Select Confirm Changes Broadband Module Broadband Module ADSL Modem Confirm Basic Configuration Status pus System Backup Restore RR System Restart The following values will be used for your manual amp DSL Modem settings The Broadband Module WAN address
90. onfiguration Status System Backup Restore System Restart Advanced Configuration LAN Gateway ADSL Modem ETH DMZ Port VoIP VPINCI ADSL Modem Manual VPI and VCI Setup The Broadband Module needs to know which YPI and VCI it should use for Internet Access Enter the VPI and VCI values that your ISP has provided in the boxes below Q Tell me more about choosing VPI and VCI values VPI D 38 VCI Next gt Cancel VPI VCI Virtual Path Identifier Virtual Circuit Identifier specify the ATM connection between the ADSL modem and the service provider The VPI range is O 4095 The VCI range is O 65535 The default values are 0 58 Select Next The following screen is displayed Enter the VPI and VCI values if they are different from the default values Broadband Module ag Broadband Module Basic Configuration Status System Backup Restore L System Restart Advanced Configuration Setup LAN Gateway ADSL Modem e Select Confirm Changes The following screen is displayed ADSL Modem Confirm Internet Access will be provided by PPPoE The VPI will be O and the VCI will be 38 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel Broadband Module E Broadband Module Basic Configuration Status _ System Backup Restor
91. ore configuration from your computer System Restart Advanced Configuration Q Tell me more about System Backup Restore Backup Configuration Backup configuration to your computer Backup Restore Configuration Restore configuration from a previously saved file Restoring the configuration will overwrite any configuration changes since the configuration was backed up Configuration File Browse Restore 57 BT Versatility Broadband Module Broadband Module Plus Manual e Select Restore When the configuration has been restored the following screen is displayed Broadband Module Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration Restart Required To implement your changes a restart is required Restart e Restart the system Configuration Restored Your configuration has been restored The configuration changes will not take effect until you restart your Broadband Module To restart now click the Restart button below 4 restart will briefly disconnect you from the Internet NOTE You must restart your Broadband Module before making any further configuration changes Restart The module restarts and the Basic Configuration is displayed SYSTEM RESTART This allows you to restart the module e Select System Restart from the menu The following page is displayed Broadband Module B
92. ow Multiple Hosts Max Activity Interval Enable Session Chaining UDP Session Chaining Secondary Secondary Enable Port Port Allow Max Enable DE Number Number S LN E Multiple Activity Session Scot YP Start End Start End Hosts Interval Chaining Chaining Rt tcp v 1024 65535 Allow Allow v Allow v A Apply Return to Trigger List Return to Interface List Enter the following parameters Adds a trigger for a TCP or UDP application Sets the start of the trigger port range for the control session Sets the end of the trigger port range for the control session Sets the start port range that the trigger will open Sets the end of the port range that the trigger will open Allow or Block sets whether or not a secondary session can be initiated to from different remote hosts or the same remote host on an existing trigger The max interval time in milliseconds between the use of the secondary port sessions If a secondary port opened by a trigger has not been used for the specified time it is closed If this is enabled TCP dynamic sessions also become triggering sessions which allows multi level session triggering If this is enabled UDP dynamic sessions also become triggering sessions which allows multi level session triggering BT Versatility Broadband Module Broadband Module Plus Manual Binary Address Sets whether the destination IP address of the incoming Replacement packet is replaced with the associated internal
93. p Restore Broadband Module Basic Configuration Status ae System Backup Restore System Restart Advanced Configuration This page allows you to backup the configuration settings to your computer or restore configuration from your computer Q Tell me more about System Backup Restore Backup Configuration Backup configuration to your computer Backup Restore Configuration Restore configuration from a previously saved file Restoring the configuration will overwrite any configuration changes since the configuration was backed up Configuration File Browse Restore The following screen is displayed Broadband Module cs JADI Broadband Module Backup Configuration Basic Configuration Status _ System Backup Restore System Restart Advanced Configuration If the download does not start automatically please download the configuration from here Some browsers will start the backup automatically If your browser does not start automatically then e Select the link Please download the configuration from here A Windows File download screen is then displayed 56 BT Versatility Broadband Module Broadband Module Plus Manual Save As lt Local Disk C Q em OAIM Manuals Program Files My Recent LJAIM Software Qysambar 2 Documents AIM specs 14 Jun 05 sb BTLB Birmingham Sigma Do you want to save this file cache Bsr Co
94. point 2 Inactive LAN Gateway Endpoint 3 ADSL Modem Endpoint 4 ITP Extension ETH DMZ Port VoIP Endpoint 5 Inactive z ISDN Endpoint 6 Inactive v WLAN r Endpoint 7 Inactive x Endpoint 8 Inactive Endpoint 9 Inactive z Endpoint 10 Inactive Endpoint 11 Inactive Endpoint 12 Inactive z Cancel e Add Trunk from the drop down menu for every endpoint to be configured as a trunk e Select Next The following screen is displayed 33 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is displayed The following screen is displayed 34 Select Confirm Changes Broadband Module Basic Configuration Status Broadband Module VolP Confirm The endpoint settings will be System Backup Restore System Restart Type Advanced Configuration Endpoint 1 Trunk Endpoint 2 Trunk Endpoint 3 Inactive LAN Gateway Endpoint 4 Inactive ADSL Modem Endpoint 5 Inactive ETH DMZ Port Endpoint 6 Inactive VoIP Endpoint 7 Inactive ISDN Endpoint 8 Inactive WLAN Endpoint 9 Inactive Endpoint 10 Inactive Endpoint 11 Inactive Endpoint 12 Inactive eU Broadband Module Basic Configuration Status To confirm this setting click on the Confirm Changes button below If you do not wish to apply this setting click on the Cancel button Confirm Changes Cancel VoIP Endpoint Authentication You should fill out the following fields
95. pport WPA e Click Start on the task bar of the PC e Click Control Panel 88 BT Versatility Broadband Module Broadband Module Plus Manual amp Control Panel File Edit View Favorites Q X O Search gt gt Folders Ga Tools Help a Address Control Panel v Eo amp i Accessibility Add Hardware Options x 9 Broadcom Control Suite id 9 Vg Control Panel a Je Switch to Category view See Also Add or Remowv E Display Java Plug in Date and Time D windows Update Q9 Help and Support Internet Options Intel R GMA Driver for b amp Phone and Portable Media Power Options Printers and Regional and Scanners and Modem Devices rx 9 Security SigmaTel Sounds and Center Audio Audio Devices Windows Firewall _ Vb Wireless Network Set Double click the Network Connections icon Network Connections File Edit Tools Advanced Help Q Back pe Search ic Folders E View Favorites Administrative w 0 P Automatic Bluetooth Broadcom ASF Tools Updates Devices Configuration A ow ow Find Fast Folder Options Fonts Game Controllers Keyboard Mouse Network PatchLink Connections 9 Scheduled Cameras Tasks Update EN Faxes s Speech Language System Taskbar and User Accounts Start Menu Address S Network Connections Network Tasks RAS LAKE 5
96. r Tcer lelerelilemuiferelti Broadband Module Basic Configuration Status i System Backup Restore sn System Restart Advanced Configuration LAN Gateway ADSL Modem ETH DM2 Port VoIP ETH DMZ Port IP Gateway Mode Choose a type that is suitable for your Internet connection from the options below 8 Tell me more about ETH DMZ Port settings C DHCP use this if your provider uses DHCP to assign network settings pr m Cancel Select Static from the ETH DMZ Port IP Gateway Mode screen Select Next The following screen is displayed iT eT e EE LT M TE Broadband Module Basic Configuration Status is System Backup Restore j System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DM2 Port VoIP ISDM WLAN Enter the required IP addresses and Subnet mask Select Next The following screen is displayed 30 ETH DMZ Port Static IP Gateway For static configuration you must provide values for the fields below Your Service Provider or L N administrator should provide these values 3 Tell me more about static IP gateway settings Broadband Module WAN address 213 94 l222 17 Broadband Module WAN Subnet Mask 255 255 255 0 Internet Gateway address 213 94 222 176 Primary DNS address 212 5 N32 a Secondary DNS address 212 57 32 l
97. ration Addressing controls the network address of the Broadband Module Q Tell me mare about the Broadband Module address settings Currently the address settings for the Broadband Module are IP Address 192 168 2 1 Subnet Mask 255 255 255 0 Change the Broadband Module address settings here Setup LAN Gateway ADSL Modem ETH DMZ Port Note that the DHCP Server address range for LAN hosts will automatically change in the Advanced Configuration settings to reflect the new address range 18 BT Versatility Broadband Module Broadband Module Plus Manual ADSL MODEM To set up the ADSL modem obtain the following information from your service provider Type of Access Username Password VPINCI e Select ADSL Modem from the Setup menu The following screen is displayed ie Ter er Ee B LET T LS Broadband VEPHE ADSL Modem Basic Configuration Status _ System Backup Restore Ds System Restart Advanced Configuration The ADSL Modem settings control how the Broadband Module connects to the Internet 8 Tell me more about the ADSL Modem settings ADSL Modem is currently configured as follows Setup Internet Access is provided by DSL PPPoA with a VPI of O and a VCI of 38 The PPP Username is The PPP Password is not set LAM Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN Change the ADSL Modem settings here This screen shows the c
98. rd Retype the Password e Select Next The following screen is displayed 39 BT Versatility Broadband Module Broadband Module Plus Manual TOT e er Uu Te B LL EST LU LES Broadband Module ISDN Confirm Basic Configuration Status System Backup Restore System Restart Advanced Configuration ISDN will be enabled The phone number will be 923456789 The username will be username To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button LAN Gateway ADSL Modem Confirm Changes Cancel ETH DMZ Port VoIP e Select Confirm Changes The following screen is displayed Broadband Module BET Uis Urdsdband duis ISDN Basic Configuration Status The ISDN settings control how the Broadband Module uses ISDN to System Backup Restore connect to the Internet em System Restart Tell me more about the ISDN settings Advanced Configuration ISDN is currently enabled Setup F The PPP Username is username LAN Gateway The PPP Password is set ADSL Modem ETH DMZ Port The phone number is 923456789 VoIP ISDN WLAN Change the ISDN settings here The ISDN setup is now complete 40 BT Versatility Broadband Module Broadband Module Plus Manual WLAN This allows users to set up wireless PC connections and to configure their security settings The WLAN provides coverage at a range of up to 1
99. rface Interface Type 1 Type 2 Validators Policy Configuration t iE Only listed Port Host Stll erie hosts blocked Filters validators QO t d Only listed Port Host externa mz hosts blocked Filters Q9 Validators Q d int Only listed Port Host i LARS SUL hosts blocked Eilters q Yalidators e Select Host Validators for a particular interface The following screen is displayed Broadband Module Broadband Module ADSL Test Diagnostics Flash Update IP Routes PIA Cee Reset to Defaults Admin Accounts Firewall amp Security Basic Configuration Advanced Configuration Return to Interface List Host Validators No Host Validators Defined Add Host Validator QO Return to Policy List Q9 Return to Interface List Q e Select Add Host Validator for the selected interface The following screen is displayed Select Apply Save the new configuration Restart the module 70 Broadband Module 05 Broadband Module Basic Configuration __ Advanced Configuration ADSL Test iid Diagnostics Flash Update ahh E Reset to Defaults Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN Enter the host IP address and Subnet mask Select the direction Inbound Outbound or Both Configure Validators external internal Firewall Add Host Validator ex
100. roadband Module Basic Configuration Status System Backup Restore J System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DM2 Port n Tr e Select Confirm Changes The following screen is displayed ETH DMZ Port Confirm The ETH DMZ Port will use an external IP Gateway to provide internet access The network settings will be obtained by DHCP To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel 29 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Basic Configuration Status d System Backup Restore System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN The setup is now complete b Static Broadband Module ETH DMZ Port The ETH DMZ Port settings control how the Broadband Module uses the ETH DMZ Port Q Tell me more about the ETH DMZ Port settings The ETH DMZ Port is currently configured as follows The ETH DMZ Port is configured to use an external IP Gateway to provide internet access The network settings will be obtained by DHCP Change the ETH DMz Port settings here The DMZ IP Address is 192 168 0 1 The DMZ Subnet Mask is 255 255 255 0 Change the DMZ IP address here Static IP addresses will be provided by the network administrato
101. roadband Module Basic Configuration Status System Backup Restore t System Restart Advanced Configuration e Select Restart System Restart To restart now click the Restart button below 4 restart will briefly disconnect you from the Internet Restart The module restarts and the Basic Configuration page is displayed 58 BT Versatility Broadband Module Broadband Module Plus Manual ADVANCED CONFIGURATION e Select Advanced Configuration from the main menu The following screen is displayed note the warning Broadband Module Advanced Configuration Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Changing the Advanced Configuration can affect the security and functionality of the Broadband Module Only specialists with knowledge of the advanced features should make changes to the Advanced Configuration Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN The following menu items are displayed under Advanced Configuration ADMIN ACCOUNTS Access to the browser programming interface is controlled by two username password pairs which provide the user with identical programming privileges The default username password pairs are Username To change the passwords carry out the following procedure using the browser programming interface When changing the password
102. roadband Module Plus Manual ETH DMZ Port By default this port is set up as a DMZ with an IP address of 192 168 0 1 and a subnet mask of 255 255 255 0 The DHCP server is enabled on this and provides addresses in the same subnet range The ETH DMZ port can also be used to connect to an external broadband modem a LAN ora WAN or to add a host to the DMZ To do this follow the following procedure e Select ETH DMZ Port The following screen is displayed Broadband Module SEFT ETE ETH DMZ Port Basic Configuration Status The ETH DMZ Port settings control how the Broadband Module uses the System Backup Restore ETH DMZ Port B System Restart 8 Tell me more about the ETH DMZ Port settings Advanced Configuration The ETH DMZ Port is currently configured as follows Setu es The ETH DMZ Port hosts a DMZ LAN Gateway Change the ETH DMZ Port settings here ADSL Modem ETH DMZ Port vor The DMZ IP Address is 192 168 0 1 ISDN The DMZ Subnet Mask is 255 255 255 0 WLAN Change the DMZ IP address here e Select the Change the ETH DMZ settings here To Change the DMZ IP address here see page 51 Three options are presented 1 PPPoE PPPoE is used when connecting to an external broadband modem Broadband Module EREA ETH DMZ Port Mode Basic Configuration Status System Backup Restore System Restart Advanced Configuration There are three modes for the ETH DMZ Port availab
103. rovide a pass phrase for Wi Fi Protected Access This should consist of between 8 and 63 characters 8 Tell me more about Wireless network pass phrases Nus essssesescecescesese Cancel e Enter a pass phrase of between 8 and 63 characters Enter the Pass Phrase in the table provided in Appendix A as it is required when setting up PCs for wireless networking e Select Next The following screen is displayed TOT C T HT BB LL Te LV S Broadband Module Basic Configuration Status System Backup Restore SP System Restart 77 Advanced Configuration Restart Required AN Restart To implement your changes a restart is required WLAN Address Authentication You can restrict which wireless PCs can connect to your device Select how you want to restrict PCs below 8 Tell me more about restricting wireless access ER A M Lm A ard CR n Ae d C Allow all wireless PCs to connect except those I specify C Only allow the wireless PCs I specify to connect Cancel Three options are presented for Address Authentication 1 Allow any wireless PCs to connect e Select Next this takes you to Select Interface page 51 2 Allow all wireless PCs to connect except those specify e Select Next 49 BT Versatility Broadband Module Broadband Module Plus Manual The following screen is disp
104. s fe My Music 43 My Computer a My Network Places Set Program Access and Defaults a Connect To ka Printers and Faxes All Programs gt Q9 Help and Support 79 Search 17 Run Log Off 9 Shut Down start 3 3 O P G Terence williams Inbox Ty Microsoft Wo BT Versatility Broadband Module Broadband Module Plus Manual E Control Panel aloj xi File Edit View Favorites Tools Help a e Click Network Connections 5 O sean es I gt Address E Control Panel Go vz Control Panel e ETT si L e A Accessibility Add Hardware Add or Administrative ALi Sound Automatic Date and Time Display e Switch to Category View Options Remoy Tools Setup Updates See Also A F 3 4 m B gt Fonts Game Internet Keyboard PatchLink Phone an A Windows Update Controllers Options i Network Update Modem Connections Help and Support 9 3G x Regional and Scanners and Scheduled Security Sounds and Speech System Taskbar ai Language Cameras Tasks Center Audio Devices Start Mer 8 e U ga W Eb TOSHIBA User Accounts Windows Wireless Link Wireless Power Saver Firewall Network Set VRAT nega Right click Local Area Connection oe J device LAN or High Speed Internet W Repair this connection C i C k P ro p e rti es fm Rename this connection 8 Ey View status of this connection Di areas Change settings of this oe connection Status R
105. s WINS servers may 5e 3 list of IP addresses vou should type them in seperated by commas as in the following example 192 168 279 7 192 365 220 1 Option name Default gateway E Le iz te algewssv Option value iC efault qate Bu Domain name OK Reset IRC server LE HTTP server SMTP server Cancel POP3 server MNTP server WINS servers Time servers Select one of the following options from the drop down menu Default gateway Domain name IRC server HTTP server SMTP server POPS server NNTP server WINS server Time server Enter the option value in the field below Select OK To always assign the same IP address to a host The same IP address will always be assigned to a specific host with the specified MAC address Existing DHCP server subnets Use Ll local local Assign Get host host Bd rdss Auto subnet address ae Domain from IP as DNS Name interface default server gateway Advanced 192 168 1 0 2552552550 tue x tue tue x fiplan z r Options of Ad 2 192 158 0 0 255 255 255 0 tue v tue tue fipdmz r TERR Apply Reset Create new Subnet O Subnet Value Subnet Mask Delete Help There are currently no DHCP server fixed IP MAC mappings defined Create new Fixed Host O Help Select Create new Fixed Host The following screen is displayed 80 BT Versatility Broadband Module Broadband Module Plus Manual Create new DHCP server fixed host I
106. s from their default settings it is recommended that both passwords are changed To change the Admin password Connect to 192 168 1 1 WebAdmin User name 45 admin Password sesse i Remember my password Log in to the browser programming interface using the default username password admin admin e Go to Advanced Settings e Select Admin Accounts The following screen is displayed 99 BT Versatility Broadband Module Broadband Module Plus Manual ony Broadband Module Basic Configuration _ Advanced Configuration ADSL Test m Diagnostics Flash Update Reset to Defaults Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDM e Select Edit user The following screen is displayed Broadband Module configuration web pages Admin Accounts This page allows you to control access to your router s console and these Currently Defined Users User Comment admin Created by CLI Edit user engineer Created by CLI ICEL Te BB LL eT E Broadband Module Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Advanced Setup Admin Accounts Firewall amp Security IP Routes DHCP Server Advanced ISDN e Enter a new password e Select Apply To change the Engineer password Admin Accounts edit user admin Details
107. s network Q Tell me more about the wireless networks Select whether you want wireless PCs to be a part of your DMZ or your LAN DMZ Wireless PCs will have restricted access to your LAN devices C LAN Wireless PCs will be able to connect to your LAN devices Next gt Cancel Broadband Module Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN e Select Confirm Changes e Restart the module WLAN Confirm Wireless networking will be enabled The wireless network name SSID will be set to PRISM 01 1f 54 The Broadband Module will automatically select the best wireless channel The wireless networking security will be set to off SSID Broadcast will be enabled All wireless PCs will be allowed to connect to the wireless network The wireless network will be on the DMZ To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel Connecting your PC to the Wireless Network e Click Start e Click Control Panel 43 BT Versatility Broadband Module Broadband Module Plus Manual amp Control Panel File Edit View Favorites Tools Help se P Search gt Folders E Address G Control Panel v amp b amp b w ww O E Vg Control Panel a Accessibility
108. s used for system maintenance and contains the following diagnostic tools Event Log Broadband Module Diagnostics Broadband Module Basic Configuration Advanced Configuration ADSL Test Diagnostics Flash Update Reset to Defaults Welcome to the Broadband Module Please select a menu option to view diagnostic and status information about your module Diagnostics Event Log Ping Logging Shows system related events This provides diagnostic information Broadband Module Broadband Module Event log Basic Configuration Advanced Configuration ADSL Test a Diagnostics Flash Update Reset to Defaults Showing all events most recent events last times are since last reboot or real time if available Time Event Diagnostics Event Log E s Clear these entries Ping Logging Select events to view Select a lag View 85 BT Versatility Broadband Module Broadband Module Plus Manual PING This is used to test the broadband connection Ping This allows you to check the availability of the listed services Description Address Ping Status Gateway Address not currently set RUE Primary DNS nat currently set not currently set SIP Server sip bbvservice nat bt com E Secondary DMS Pi User Defined Ping IP Routes LLLI Ping Fina All Fingal f FLASH UPDATE This option is used to update the module with a new version of firmware a
109. ss PCs are currently connected bu System Backup Restore System Restart MAC Address 00 12 f0 55 7c cd Advanced Configuration Signal Strength 37 Setup Return to the wireless status page LAN Geo Return to the wireless status page ADSL Modem ETH DMZ Port VoIP ISDN WLAN Setting up WLAN with Security The recommended settings to provide maximum security are indicated as Recommended Where instructed enter the relevant information in the table provided in Appendix A as this information is required when setting up PCs for wireless networking e Select WLAN The following screen is displayed 45 BT Versatility Broadband Module Broadband Module Plus Manual D Broadband Module Basic Configuration Status pis System Backup Restore 2 System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDM WLAN First Time Settings Broadband Module WLAN Wireless networking allows you to connect wireless PCs through the Broadband Module to the Internet Q Tell me more about the wireless networking settings The wireless settings are split into two sections the first section contains settings which need to be configured before you use wireless for the first time but are unlikely to be changed after that The second section contains settings you might change more often First Time Settings The wireless first time settings wizard helps you enable your wirele
110. ss for the first time you probably won t need to change these settings after you have entered them once Wireless networking is currently set to operate in United Kingdom Wireless network type is currently 802 11B G Change your wireless first time settings here This automatically takes you through the configuration screens necessary for setting up the wireless network for the first time e Select Change your wireless first time settings here The following page is displayed TOT e eU Te T LU Ee Broadband Module Basic Configuration Status System Backup Restore EE system Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP TOMAI WLAN Set Country To make sure the Broadband Module does not transmit on illegal frequencies you must set where you are in the world Tell me more about setting a country A Country United Kingdom Confirm Changes gt Cancel Continuing beyond this page will clear your other wireless settings so you will be asked to enter them again e Select United Kingdom default setting from the drop down menu e Select Confirm Changes The following screen is displayed Broadband Module Broadband Module Basic Configuration Status System Backup Restore System Restart Advanced Configuration To implement your changes a restart is required Restart Three WLA
111. sses on the subnet or altering option configuration parameters offered to DHCP clients on this subnet Parameters for this subnet Edit the gefinition of the DACP subnet here If you go not wish to specify the subnet value and subnet mask by hand you may instead select an IP Interface using the Get subnet from IP interface field The subnet wil track the IP address and subnet mask belonging to the chosen IP interface Subnet value 482 M68 INN nm Subnet mask 255 255 255 m Get subnet from IP interface iplan Maximum lease time 259200 seconds Default lease time 259200 0 seconds The current subnet parameters are shown These can be changed as required IP addresses to be available on this subnet 78 BT Versatility Broadband Module Broadband Module Plus Manual IP addresses to be available on this subnet You need to make sure that the start and end agdgresses offered in this range are within the subnet you defined above Alternatively you may check the Use a default range box to assign a suitable default IP address poo on this subnet Start of address range i i i T End of address range 192 Use a default range vw The range of IP addresses available on the subnet is shown These can be changed if required DNS Server option information DNS server option information Enter the addresses of Primary and Secondary ONS servers to be provided to DOHC chants on this subnet You may instead alow DHCP
112. tain different security filters for each interface WAN LAN WAN DMZ DMZ LAN When None is selected all traffic is blocked Additional filters can be added to each security level as required The default setting is High Security Level The Medium Security level has additional filters For example it is set up to allow access to a web server or a mail server on the DMZ from the External interface The Low Security level adds more filters For example as well as allowing access to a web server or a mail server on the DMZ it also allows Telnet and FTP access from the External interface The pre defined security configurations are External External DMZ High Security Level lt gt lt gt from any source IP address or any Internal Internal source Service Destination Port ICMP 0 65535 0 65535 RMCP 5 5 8 o MERNENNE 51 ISAKMP F F F 0 F 1 F F F 8 F F F 3 F 3 F F F 1 ME o ES E pF Else BE ONE EF Lp M i e RE NE E L POPS i TCP OHIO f F LEE DROP n 125 LE TE T E p SSA I4 CP e 22 00 Et D D ETTET E T PT TCP 556 j T TyjJ T T TO OT 88 8 amp 8 HTTP TCP 80 F ER qom L 95 ER C NMEN 88 5 2 25 2 External External Medium Security Level lt gt lt gt from any source IP address or any Internal DMZ Internal source port peamant n On m om m om STP 51 ee Fyj T TJ rF F F D F F HTTP TCP 80 F 63 BT Versatility Br
113. ternal internal Add Host Validator Host IP Address 192 168 1 7 Host Subnet Mask 255 255 255 0 Direction both Return to Validator List Return to Policy List Q Return to Interface List BT Versatility Broadband Module Broadband Module Plus Manual Application Level Gateways There are certain applications that NAT and Firewall configurations cannot manage In many cases ALGs Application Level Gateways are needed to translate and transport packets correctly An ALG provides a service for a specific application such as FTP File Transfer Protocol Incoming packets are checked against existing NAT rules or Firewall filters IP addresses are evaluated and detailed packet analysis is performed If necessary the content of a packet is modified and if a secondary port is required the ALG will open one The ALG for each application does not require any configuration ALG support is provided for the following applications If support is required for additional applications security triggers can be configured for these Application TCP Port UDP Port AIM AOL Instant Messenger 5190 N A FTP File Transfer Protocol N A IKE Internet Key Exchange N A 500 ILS Internet Locator Service 389 1002 N A MSN Microsoft Networks 1863 PPTP Point to Point Tunnelling 1723 Protocol RSVP Resource Reservation Protocol N A L2TP Layer 2 Tunnelling Protocol N A SIP Session Initiation Protocol
114. to the programming interface ccce eee eene nere eas 10 Setmo MUD PAD SL T 10 Settingedp IP TEF DEKS uctor obl onetco v ua seen Oi Or olei s v oue oa meer utu teu d nate nave E AEDEM 12 Setting p IP Extelisloris sese eder i er rn ee ee Pete iis E eU LUE 12 Setting up UM SerVICe idees teint rb er e IV aUa VH en UM EE EE 15 Programming from BT Versatility Wizard ssssssssee eene 16 BASIC CONEIGURATION S aset E 17 SOUD MENU da ads teed ci trite Om TREE 17 AN Ce EVV NS 17 ADSL MOGdeIm usdetontade ceret uen E tent mote sua Botero states edo E E EE 19 SB U 19 2 nd sd Pe ET E 21 2p M e MERERETUR a as E NT 23 tA Mattia E c eh tata se E Eam dl S c pl EQ ate cease corr ace eL aet 24 ETRUDIZ PORE 2223 coriis APER esu Qu cada bu va osa E kic ve tetas bo M Tosdes coda id dida ced ioa dud 27 ED PPEROE CEN E NUMEN Pu ME M T DL M 27 PAA EEEE A EEE E EAR A T LM E AC AR eT MEE LEM 29 OROM E EE 31 VOIP T 535 Manually Connguriha UP TUK S essor metere eese t queue ebat E EEA 33 Additional Endpoint Options 00 0 0 cece cccccsscscccccssssscceessssssccssessssecccsesssssscseesssssecesesassseseeseseess 35 Advanced MolIPSSePrtilitsu eom e xD D Mm I UM EC EM DL E PEE 36 Unified IMessadildg Seti ds aee cuite b e ECT Ple isane uis NS dte E co eeu eee ee eases 36 ISDN sss oa eie Pica aeta D HUNE PEIUS
115. tup LAN Gateway ADSL Modem ETH DMZ Port MaTP e Enter the new IP address and Subnet Mask e Select Next The following screen is displayed e Select Confirm Changes Broadband Module SENA LAN Gateway Confirm Basic Configuration Status System Backup Restore i System Restart Advanced Configuration The IP address for the Broadband Module will be 192 168 2 1 The Subnet Mask for the Broadband Module will be 255 255 255 0 To confirm this setting click on the Confirm Changes button below If you do not wish to apply this setting click on the Cancel button Confirm Changes Cancel Setup LAN Gateway ADSL Modem The following screen is displayed ICEL EU B LET DOES EET Changing IP Address For The Broadband Module Basic Configuration Status System Backup Restore System Restart B Advanced Configuration Your router s IP address is being changed There will be a short pause while the address is changed and then you will be redirected to the new address If you have not been redirected within 30 seconds click on this link to go to the new address Setup LAN Gateway ADSL Modem ETH DMZ Port When the new parameters have been saved the following screen is displayed showing the new settings Broadband Module Broadband Fioduls Add ressing Basic Configuration Status System Backup Restore K System Restart Advanced Configu
116. twork Places Personal Area Network Bluetooth Network Connection Disconnected E Bluetooth Device Personal Ar My Documents qj My Computer Details Network Connections System Folder e Double click the Wireless Network Connection icon 44 BT Versatility Broadband Module Broadband Module Plus Manual i Wireless Network Connection Choose a wireless network Network Tasks q Refresh network list Click an item in the list below to connect to a wireless network in range or to get more information lt 2 Set up a wireless network for a home or small office Related Tasks damians_wpa_aim WD Learn about wireless Unsecured wireless network networking PRISM_01_5f_79_bernar gfe Change the order of preferred networks t Security enabled wireless network y Change science CSE lab Wireless AIM settings f Security enabled wireless network WPA PRISM 01 1f 5d Unsecured wireless network Reservoir sig 5g Security enabled wireless network WPA A list of wireless networks is displayed e Select the SSID being broadcast by the module e Click Connect You will now connect to the Wireless LAN Connected wireless PCs Selecting the View details of connected wireless PCs link under General Settings takes you to the following screen which shows details of PCs connected to the WLAN Broadband Module WLAN Connected Wireless PCs Basic Configuration Status The following 1 wirele
117. ur changes a restart is required The entered MAC address is displayed Add an address here takes you back to the previous screen to enter another MAC address Remove an address here takes you to the following screen Broadband Module PEE WLAN Address Authentication Basic Configuration Status System Backup Restore ii System Restart Advanced Configuration Select the MAC address to remove below Tell me more about restricting wireless access 00 1 0 35 03 2C 07 00 10 35 03 2C 07 Cancel Restart Required To implement your changes a restart is e Select the address to remove from the drop down menu 90 BT Versatility Broadband Module Broadband Module Plus Manual e Select Next this takes you back to the Allow all wireless PCs to connect except those specify option 2 Only allow the wireless PCs specify to connect Recommended Refer to Appendix B to find out the MAC address of a PC Enter the MAC Addresses in the table provided in Appendix A e Select Next The following screen is displayed Broadband Module AA WLAN Address Authentication Basic Configuration Status System Backup Restore pi System Restart Advanced Configuration You can configure the list of addresses to allow access to your device below 8 Tell me more about restricting wireless access No addresses have been set Restart Required To impl
118. urrent settings e Select Change the ADSL Modem settings here The following screen is displayed Broadband Module TCE ADSL Modem Types of Access Basic Configuration Status There are five types of Internet Access available Choose a type that is System Backup Restore suitable for your Internet connection from the options below B System Restart 8 Tell me more about ADSL Modem settings Advanced Configuration PPPoA use this if you have a PPPoA DSL connection enn PPPoE use this if you have a PPPoE DSL connection etup LAN Gateway ADSL Modem ETH DMZ Port servers directly C C DHCP use this if you have a DHCP DSL connection C Manual use this to configure your connection s gateway and DNS VoIP WLAN Four options are presented for Type of Access 1 PPPoA This option uses Point to Point Protocol over ATM e Select PPPoA from the ADSL Modem Types of Access screen e Select Next The following screen is displayed 19 BT Versatility Broadband Module Broadband Module Plus Manual Broadband Module Broadband Module Basic Configuration Status System Backup Restore Ki System Restart Advanced Configuration Setup LAN Gateway ADSL Modem ETH DMZ Port VoIP ISDN WLAN ADSL Modem PPPoA In order to use a PPPoA connection to the Internet you must supply a username and password to logon to your Internet Service Provider ISP Your ISP should
119. us Manual APPENDIX B To find out the MAC address of a PC e Click start e Click Run Type the name of a program folder document or Internet resource and Windows will open it For you cmd e Enter cmd ct C WINDOWS system32 cmd exe Microsoft Windows XP Version 5 1 2600 lt C gt Copyright 1985 2661 Microsoft Corp C Documents and Settings terrywilliams Desktop gt ipconf ig all_ e Atthe prompt gt type ipconfig all return c C WINDOWS system32 cmd exe Microsoft Windows XP Version 5 1 2666 lt C gt Copyright 1985 2661 Microsoft Corp C Documents and Settings terrywilliams Desktop gt ipconfig all Mindows IP Configuration Host Name WILLIAMS_TERRY Primary Dns Suffix lakecommunications com Node Type Hybrid IP Routing Enable care N dU Ethernet adapter Wireless Network Connection Media State Media disconnected Description _Intel R gt PRO Wireless 2206BG Ne Connection 80 12 F8 55 7C CD C Documents and Settings terrywilliams Desktop gt The MAC address is displayed under Ethernet adapter Wireless Network Connection Physical Address MAC address 92 Index Admin 33 ADSL 8 ADSL Health Check 50 Advanced Configuration 52 Advanced NAT Configuration 57 Auto configuration 12 Application Level Gateways 42 ATM 14 Basic Configuration Blacklist 45 Codecs 5 29 Connections 3 DHCP 11 18 DMZ 28 DOS Att
120. will be 213 94 222 177 Advanced Configuration The Broadband Module WAN Subnet Mask will be 255 255 255 0 ER The Internet Gateway address will be 213 94 222 176 etup LAM Gateway ADSL Modem ETH DMZ Port VoIP The YPI will be O and the VCI will be 38 ISDM WLAN The Primary DNS Server will be 212 17 32 1 The Secondary DNS Server will be 212 17 32 3 To confirm these settings click on the Confirm Changes button below If you do not wish to apply these settings click on the Cancel button Confirm Changes Cancel The following screen is displayed Restart the module ICEL Ee BB LL eT DOES 1 ADSL Modem Broadband Module Basic Configuration l Status NS System Backup Restore 3 System Restart Advanced Configuration The ADSL Modem settings control how the Broadband Module connects to the Internet Q Tell me more about the ADSL Modem settings ADSL Modem is currently configured as follows Restart Required To implement your changes a restart is required Restart Setup Internet Access is manually configured with a VPI of 0 and a VCI of 38 The WAN IP Address is 213 94 222 177 The WAN Subnet Mask is 255 255 255 0 The WAN Default Gateway is 213 94 222 176 The Primary DNS Server is 212 17 32 1 The Secondary DNS Server is 212 17 32 3 Change the ADSL Modem settings here LAN Gateway The ADSL Modem setup is now complete 26 BT Versatility Broadband Module B

Broadband Module/ Broadband Module Plus

Contents

Download Pdf Manuals

Related Search

Related Contents