User Manual & Programming Guide 4.0
Contents
1. 8 8 Mounting Template Section 3 Features of your eVault No Look Entry System Unique LCD Provides Visual Lock StatuS eveoo and ev1200 oniy Programmable Combination Pry resistant Recessed Door Powder Coat Tuff Finish Tamper Detect System Security Lockdown System Low Battery Indicator Combination Retained if Power is Lost Spring Loaded Door for Quick Access Backup Key Entry System Padded Interior 16 Gauge Steel Construction Optional Security Cable Section 4 Getting Started First Time Use You must open your eVault with the keys to gain access to the inside before attempting to install the batteries DEFAULT CODE is set to 1 2 3 4 Left to Right 4 1 Key Operation Locate the two 2 keys provided with your eVault Insert the key into the key cylinder and rotate to open the door manually DO NOT store your keys inside your eVault We recommend storing the keys separatly and recording the key code located on the key in the event they are lost 4 2 Installing the Batteries Locate the battery compartment on the top rear of the inside of your eVault and remove by un screwing the two 2 thumb screws Remove the battery compartment by un plugging the wire snap from the side and slide off the strap that retains the batteries Install eight 8 AA batteries connect the wire snap to the compar2. Combination Read thru before attemping The setup button is located INSIDE of your eVault beneath the 2 entry button Press setup button for 2 seconds Green LED flashes amp remains on Enter your 4 digit code Press setup button for 2 seconds LED will turn red amp remains on Enter your 4 digit code 2 time Press setup button for 2 seconds LED turns green and flashes 5 times Note New Code failed if the LED flashes 5 times RED Repeat 4 6 4 6 Lockdown A Lockdown condition occurs when 3 invalid combinations are entered Your eVault will not accept any pushbutton entries for two 2 minutes 4 7 Alarm An audible alarm will sound after the 2 minute lockdown condition if another invalid entry is attempted 20 short audible ticks will be heard first then a 2 minute alarm The ONLY way to silence the alarm is to enter the correct code 4 8 Tamper Detect The Tamper Detect will tell you if your eVault has had an invalid entry attempt Press down keypad buttons 1 and 4 for 5 seconds to display the LED light Red light indicates an invalid entry attempt and a Green light indicates No invalid entry attempt detected 4 9 Turning Sound ON OFF Read thru before attemping To Turn ON Press setup button for 2 seconds Green LED flashes 1 time Press setup button for 2 seconds Green LED flashes 2 times Release the setup button Press keypad button 1 for 10 seconds Green LED flashes 3 ti
3. Revision GRANITE SECURITY PRODUCTS INC WINCHESTER SAFES eVault eV400 eV600 eV1200 User Manual amp Programming Guide GRANITE SECURITY PRODUCTS INC User Manual amp Programming Guide Granite Security Products Inc 4801 Esco Dr Fort Worth TX 76140 www winchesterevault com Table of Content Section 1 Introduction to your eVault Section 2 List of Contents Section 3 Features of your eVault Section 4 Getting Started 4 1 Key Operation 4 2 Installing the Batteries 4 3 Connecting the External Power Supply 4 4 Keypad Operation 4 5 Programming amp Changing Combination 4 6 Lockdown 4 7 Alarm 4 8 Tamper Detect 4 9 Turning Sound On Off 4 10 Low Battery Indicator 4 11 Use of Security Cable optional Section 5 Mounting your eVault Section 1 Introduction to your eVault Congratulations on your purchase of an eVault The components that make up your eVault are of the highest quality and workmanship to insure years of service and reliability Please take a moment and fill out your registration card or register online at www winchesterevault com Section 2 List of Contents 1 eVault Unit eV400 eV600 eV1200 2 Battery Compartment with two 2 Screws Located inside your eVault 3 External Power Supply Located inside your eVault eV600 amp eV1200 Only 4 Two Keys 6 Warranty Certificate 7 2 3 4 5 User Manual amp Programming Guide 6 7 Product Registration Form
4. mes To Turn OFF Press setup button for 2 seconds Green LED flashes 1 time Press setup button for 2 seconds Green LED flashes 2 times Release the setup button Press keypad button 2 for 10 seconds Green LED flashes 3 times 4 10 Low Battery Your eVault will monitor your battery level and displays that status on the LCD 3 cells indicates FULL Capacity 2 cells indicates 60 Capacity and 1 cell indicates LOW Capacity 4 11 Use of Security Cable optional The use of the optional security cable allows your eVault to be relocated and secured There are two 2 knock out holes located on the sides of your eVault Use a punch and hammer to remove the knock outs To Install Using the end of the security cable with the loop secure the cable to a stationary object Next insert the threaded end of the security cable into the side of your eVault Place the lockwasher c over the threads and secure with the hex nut b Insert the safety pin to retain the hex nut a Section 5 Mounting your eVault SEE OPERATING MANUAL FOR IMPORTANT WARNINGS CF V400 Template eV600 Template _ _ V1200 Template 5 1 5 2 5 3 5 4 9 9 ia Locate your template at your mounting location Mark with a pencil all 6 holes as located on the template Remove the template and drill the holes Install screws in holes 4 and 6 leaving approx 1 8 inch under the screw head and mou
5. nting surface This is to allow the screw to slide on the slotted hole Position your eVault over the mounting screws and lower it down Gently slide your eVault back and install the remaining 4 screws from the inside You will need to carefully remove the padded bottom to gain access to the holes Reinstall the padded bottom once mounting is complete
6. tment replace the battery retaining strap and secure the compartment with the thumb screws IMPORTANT We recommend Duracell AA batteries NEVER attempt to use a volt battery or re chargeable batteries as this will not work with your eVault and may damage the electronics 4 3 Connecting the External Power Supply eV600 amp eV1200 Locate the AC DC external power supply and plug the small connector into your eVault Plug the other end into a grounded recepticle Your eVault will operate with either batteries and or the external power supply attached Your eVault will retain your combination in the event of a full power loss 4 4 Keypad Operation Your eVault is equiped with a 4 digit keypad designed to provide No Look access The raised No Look guide lines located just below each of the 4 buttons are designed to operate the keypad in the dark poorly lit areas or special mounting applications The Keypad also features Braille When your eVault is alseep LCD is not lit any one 1 of the buttons will wake up your eVault DEFAULT CODE is setto 1 2 3 4 Left to Right To enter you 4 digit combination press firmly down on the buttons and you will receive a in the LCD and an audible beep confirming each entry Enter the entire 4 digit code 1 button at a time When the correct 4 digit code has been entered your eVault door will open and the LCD will varify with an open padlock icon 4 5 Programming amp Changing
Download Pdf Manuals
Related Search