JX2360 UM - FLASHELEK
Contents
1. JX 2360 User manual Release 1 0 This document is subject to modification without notice Please if necessary ask for new release at contact flashelek com FLASHELEK 2007 17 rue Marcel Sembat F 21000 DIJON NR NAUA Table of contents Erona NR NN ANN NN 3 POYSICA AS AA chia A EE EE NS 3 2 AS DS DO IO O va 3 2 SAME Base SEC in ida 4 2 3 CONS A a da 5 224 BUS MOE iii ad a tee ana aaa aa lade ee eh 5 Dz Anao mode iii A a di a a ion 6 SECT AAA SATA AAA AAA AAA 7 Technical speciticato sta 2 WINO deal 9 Pac a aaa a 9 Spare DAS a 10 2 10 1 Generals The JX 2360 set has to be used in conjonction with a PAR 56 Type Flash lamp 2000V typ In this case 1t complies with ICAO Annex 14 recommandations The JX 2360 can be used to realise SFLS cat I and cat II II with and without RTIL It also can be used as RTIL only ODALS and Helipad approach 2 Physical wiring 2 1 Mains The Power Station supplies the sets with main 230V AC 10 Black wite on diagram The mains cable have to be able to supply 0 5 rms A 230 V AC or 1 rms A 110 V AC for each flash lamp This power supply is maintained continuously on line as the eventual heater resistor may Power Station have to be supplied Anyway in case when the heater resistor have to be switched off it must JX 5600 be supplied with a separate cable The Supervision system for example JX 5600 will be in charge of switching On and Off the flashes 32. 10 2 2 Time Base sequence This flash is the Master Its internal clock pilots the repetition The sets are hierarchicaly period of the whole SFLS sequenced via an unique It has to be setted in factory analog time base line clock signal blue wite on diagram This signal passes through single shielded wire Each clock top is a 20Vpp pulse of 10 ms duration Power Station These 2 flashes are RTILS They have no intervall delay and by the fact flash always together as one They have to be setted in factory 4 10 23 Commands 2 3 1 J Bus mode E a Connect a J Bus Load here Power Station es E It is recommanded to insert a signal repeater every 1 000 m gt Connect a J Bus Load here The sets are monitored and controled via a serie RS485 digital bus called J Bus Green wire on diagram This bus is constructed with a shielded twist pair cable This bus allows JX 5600 to 1 Command the sets 2 Query the sets It is necessary to connect a J Bus Load on each end of line to insure a perfect impedance for the digital signal 3 J Bus Loads are delivered with each X 5600 A signal repeater symetrical amplifier may be necessary when the line is longer than 1 000 m even if a 1 600 m trial succeded The J Bus lets the JX 5600 command the flash sets state and query sets infos For more details see JX5600 User Manual document 1 If you need spare parts do not h
3. esitate to ask at your reseller or contact flashelek com 2 Ordered separately Ask your reseller for details or send a mail at contact flashelek com 5 10 2 3 2 Analog mode The sets can also be monitored by short circuiting 3 wires onto a ground 4 wire On the connector the wiring can be done as follow When short circuiting 4 to 2 the sets goes ON When they ate ON When short circuiting 1 to 2 the sets goes on HI mode When short circuiting 3 to 2 the sets goes on MI mode Otherwise the sets goes on Ll mode E Y POTES 9 AS A BEE OOO E g D ol h Switch on HI Switch on MI Switch ON 6 10 3 Setting up The sets are configured in factory you normally need nt change the configuration Anyway if it would be necessary proceed as follow Open the cabinet On the clock panel locate the 8 micro switches Verify that the switches nbr 1 7 and 8 are ON e Master Slave To configure the set on MASTER push the switch nbr 2 ON To configure the set on SLAVE push the switch nbr 2 OFF e Inter Flash Delay Configure the switch nbr 3 and 4 as follow RTIL 14 ms 67 ms 267 ms e Period 1 5 s 2s Configure the switch nbr 5 and 6 as follow 7 10 0 5 s 1s On the auxiliary panel locate the micro switch of the RTIL Lock e On the MASTER and on the SLAVES this switch has to be ON e On the two RTILS this switch has to be OFF this will activate the auto locking syste
4. m By the fact when one of the two RTIL is faulty the other stops flashing 8 10 4 Technical specifications Power supply Repetion period Inter flash delay Brilliance levels Power consumption Cos y Efficiency Working temperature range External dimensions 5 Wiring 230V AC 10 50 Hz 110V AC 60Hx on demand 0 5s 1s 1 5s 2s setted in factory these values can be changed on site with JX3600 interface 14 ms 67 ms 267 ms setted in factory these values can be changed on site with JX3600 interface Hight intensity 100 day mode Medium intensity 10 crepuscular mode Low intensity 3 night mode these values can be changed on site with JX3600 interface or via simple switches 150 VA typ Higher than 0 95 Higher than 80 25 C to 55 C Outer boxes may be equiped with a heater resistor for very low temperature or particularly high moisture H 350 mm x W 300 mm x D 172 mm For wiring details see the Outer Box connection manual 6 Packing Each set is delivered with an OuterBox connector Weight H 320 mm x W 440 mm x D 280 mm 8 kg 9 10 7 Spare parts Order Code 1 Power Supply 30 07 04 2 Clock Panel 30 13 64 3 Auxiliary Panel 30 07 02 4 Set of capacitors 31 00 30 5 Power coil 41 00 20 6 Set of fuses by 5 31 00 05 10 10
Download Pdf Manuals
Related Search